[why]
Due to bad hardware, the PHY repeater count in LTTPR cap is read as 0xFF
in some monitors while the LTTPR is actually present.

[how]
Remove PHY repeater counter check when configuring LTTPR mode.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
indirect register index/data pair may be used by multi-threads.  when it
happens, it would cause register access issue that is hard to trace.

[How]
Using cgs service, which provide a sync indirect reg access api.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Roy Chan <roy.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

DSC sequence for non virtual dpcd synaptics hub
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Determine if DFP present and the type of downstream device
based on dsc_aux
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Sequence to reset synaptics SDP fifo before enabling first stream
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why/How]
We need to handle cable capabilities for cables that support cable ID.
The cable attributes are intersected with the verified link caps to
determine appropriate max link rate. After determining cable attributes
we update the DP receiver.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
If the DPCD caps specifies a PSR version newer than PSR_VERSION_1 then
we fallback to using PSR_VERSION_1 in amdgpu_dm_set_psr_caps.

This gets overriden with the raw DPCD value in amdgpu_dm_link_setup_psr,
which can result in DMCUB hanging if we pass in an unsupported PSR
version number.

[How]
Fix the hang by using link->psr_settings.psr_version directly during
amdgpu_dm_link_setup_psr.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Prepare for future dm can have different implementation depends on the
return value.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DMCUB will hang if we send a PSR unsupported set version command.

This can occur if we fall-through into the default case in the switch
statement for PSR version.

[How]
Add an unsupported check after the switch statement.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY?]
SKUs that contain an unused eDP connector will throw an error when no
display is connected.

[HOW?]
Change error to a warning.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dillon Varone <divarone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Implement handling for escape call to query the MCLK switch support for
the current display config.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why & How]
Increase width of some variables to avoid comparing integers of
different widths
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Link encoders are created based on its engine ID. The position of a link
encoder in an array could be null since it didn't be allocated.  Current
matching logic didn't consider this situation and could get null
encoder.

[How]
To add null encoder check to make the matching logic can go to next to
get a valid one.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Currently, when we're tentatively detecting link configuration under mst
case, we will wrongly notify a none existing stream sink to drm layer.

It's due to we'll call amdgpu_dm_update_connector_after_detect() within
dm_helpers_read_local_edid() to update connector when we're still under
tentative detection procedure.

[How]
dm_helpers_read_local_edid() was designed to do "read" only. Don't
update drm connector status when we're still under detection process.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
There is a recent refactor that contains a typo to cause set throttled
vcp size skipped for dpia link. The change is to fix this typo so it won't cause
black screen
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
This is internal to dc so we don't have to add a prefix to indicate it
is dc link_hwss instead someone else link_hwss.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
as we add more link_hwss we are making a generic way to determine which type
of link_hwss we should use.
Later on we may think of introduce a link policy layer. it could be a thin layer
that decide the type of link_hwss we use. So instead of passing in link and link_res
we can just pass in link_policy and swtich based on link_policy->get_link_hwss_type.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
Current we have hundreds of if/else or switch statement to check
encoder type in dc_link level. The reason is because depending
on the type of encoder dc_link needs to perform similar programming
task but with different encoder interfaces. The story is to abstract
these interfaces so dc_link can just perform the programming task
without knowing the detail of which encoder it's dealing with.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why & How]
DCN guard is not necessary for DP2.x relevant logic.
Drop them.

v2: squash in fix for misplaced #endif (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
According to the USB4 specification, FEC and DSC should be disabled
when a USB4 DPIA operates in TBT3 compatibility mode.

[How]
Upon detecting that a USB4 DPIA is connected to a device that is known
to operate in TBT3 mode, disable FEC and DSC support if they have been
reported by the TBT3 device.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
dc_link_detect_helper has multiple purpose:
1. Detect link and local sink.
2. Verify link capability by performing detection link training.
3. Start mst topology discovery and if succeeded fails the current interface.

This is difficult to maintain as item 2 has become more destructive to current
dc state. The change is to decouple these sequences to its own functions.
Eventually only item 2 is a destructive method and we will redesign this
sequence with a more unified policy across different encoder types.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove redundant code and use general smu_v11_0_fini_smc_tables function.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Some clients(e.g., kfd) query sclk/mclk through this function.
As cyan skillfish doesn't support dpm, for sclk, set min/max
to CYAN_SKILLFISH_SCLK_MIN/CYAN_SKILLFISH_SCLK_MAX(to maintain the
existing logic).For others, set both min and max to current value.

Before this patch:
 # /opt/rocm/opencl/bin/clinfo

 Max clock frequency:                           0Mhz

After this patch:
 # /opt/rocm/opencl/bin/clinfo

 Max clock frequency:                           2000Mhz

v2:
 - Maintain the existing min/max sclk logic.(Lijo)
v3:
 - Avoid fetching metrics table twice.(Lijo)
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This reverts commit df4f0041.

Xgmi ras initialization had been moved from .late_init to early_init,
the defect of repeated calling amdgpu_ras_register_ras_block had been
fixed, so revert this patch.
Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Move xgmi ras initialization from .late_init to .early_init, which let
xgmi ras can be initialized only once.
Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Pmfw read ecc info registers in the following order,
     umc0: ch_inst 0, 1, 2 ... 7
     umc1: ch_inst 0, 1, 2 ... 7
The position of the register value stored in eccinfo
table is calculated according to the below formula,
     channel_index = umc_inst * channel_in_umc + ch_inst
Driver directly use the index of eccinfo table array
as channel index, it's not correct, driver needs convert
eccinfo table array index to channel index according to
channel_idx_tbl.
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

create a common helper function for soc15 and onwards
to read bios image from rom
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Not needed anymore.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Zhou, Peng Ju <PengJu.Zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Instead of ip specific implementation for rlcg
indirect register access
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Zhou, Peng Ju <PengJu.Zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The helper will be used to access registers from sriov
guest in full access time
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Zhou, Peng Ju <PengJu.Zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Initialize all the register offsets that will be
used in rlcg indirect reg access path for gfx10
in sw_init phase
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Zhou, Peng Ju <PengJu.Zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Initialize all the register offsets that will be
used in rlcg indirect reg access path for gfx9 in
sw_init phase
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Zhou, Peng Ju <PengJu.Zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add structures that are used to cache registers offsets
for rlcg indirect reg access ctrl and flag availability
of such interface
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Zhou, Peng Ju <PengJu.Zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Switch to common helper to query rlcg access flag
specified by sriov host driver for gfx10
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Zhou, Peng Ju <PengJu.Zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Switch to common helper to query rlcg access flag
specified by sriov host driver for gfx9
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Zhou, Peng Ju <PengJu.Zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Query rlc indirect register access approach specified
by sriov host driver per ip blocks
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Zhou, Peng Ju <PengJu.Zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Eliminate the follow smatch warning:
drivers/gpu/drm/amd/display/dc/dml/calcs/dce_calcs.c:3415 bw_calcs() warn: inconsistent indenting
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
Resource release is needed on the error handling path
to prevent memory leak.

[how]
Fix this by adding kfree on the error handling path.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Yongzhi Liu <lyz_cs@pku.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Clean the following coccicheck warning:

./drivers/gpu/drm/amd/pm/legacy-dpm/si_dpm.c:7035:2-4: WARNING: possible
condition with no effect (if == else).
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This issue takes place in an error path in
amdgpu_cs_fence_to_handle_ioctl(). When `info->in.what` falls into
default case, the function simply returns -EINVAL, forgetting to
decrement the reference count of a dma_fence obj, which is bumped
earlier by amdgpu_cs_get_fence(). This may result in reference count
leaks.

Fix it by decreasing the refcount of specific object before returning
the error code.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>