Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This matters to any sort of device that is wired to one of the CPU
interrupt pins on an SMP system.  Typically the scenario is most easily
triggered with the count/compare timer interrupt where the same interrupt
number and thus irq_desc is used on each processor.

   CPU A			CPU B

   do_IRQ()
   generic_handle_irq()
   handle_level_irq()
   spin_lock(desc_lock)
   set IRQ_INPROGRESS
   spin_unlock(desc_lock)
				do_IRQ()
				generic_handle_irq()
				handle_level_irq()
				spin_lock(desc_lock)
				IRQ_INPROGRESS set => bail out
   spin_lock(desc_lock)
   clear IRQ_INPROGRESS
   spin_unlock(desc_lock)

In case of the cp0 compare interrupt this means the interrupt will be
acked and not handled or re-armed on CPU b, so there won't be any timer
interrupt until the count register wraps around.

With kernels 2.6.20 ... 2.6.23 we usually were lucky that things were just
working right on VSMP because the count registers are synchronized on
bootup so it takes something that disables interrupts for a long time on
one processor to trigger this one.

For scenarios where an interrupt is multicasted or broadcasted over several
CPUs the existing code was safe and the fix will break it.  There is no
way to know in the interrupt controller code because it is abstracted from
the platform code.  I think we do not have such a setup currently, so this
should be ok.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The GNU `config.guess' uses "linux-gnu" as the canonical system name.
Fix the list of compiler prefixes checked to spell it correctly.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Adds a JR.HB after halting a TC, to ensure that the TC has really halted.
only modifies the TCSTATUS register when the TC is safely halted.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

We have no guarantee by the generic time code that the timer is stopped
when the ->next_event method is called.  Modifying the Timer Initial Count
register while the timer is enabled has UNPREDICTABLE effect according to
the BCM1250/BCM1125/BCM1125H User Manual.  So stop the timer before
reprogramming.

This is a paranoia fix; no ill effects have been observed previously.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

For the old minimum of a single tick a value of zero would be programmed
into the init value register which in the BCM1250/BCM1125/BCM1125H User
Manual in the Timer Special Cases section is documented to have
UNPREDICTABLE effect.

Observable sympthoms of this bug were hangs of several seconds on the
console during bootup and later if both dyntick and highres timer options
were activated.

In theory contiguous mode of the timers is also affected but in an act of
hopeless lack of realism I'll assume nobody will ever configure a KERNEL
for HZ > 500kHz but if so I leave that to evolution to sort out.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The range of MIPS_CPU IRQ and the range of LASAT IRQ overlap.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Shadow register support would not possibly have worked on multicore
systems.  The support code for it was also depending not on MIPS R2 but
VSMP or SMTC kernels even though it makes perfect sense with UP kernels.

SR sets are a scarce resource and the expected usage pattern is that
users actually hardcode the register set numbers in their code.  So fix
the allocator by ditching it.  Move the remaining CPU probe bits into
the generic CPU probe.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This avoids us executing an mfc0 c0_count instruction on processors which
don't have but also on certain R4000 and R4400 versions where reading from
the count register just in the very moment when its value equals
c0_compare will result in the timer interrupt getting lost.

There is still a number of users of get_cycles remaining outside the
arch code:

crypto/tcrypt.c:                start = get_cycles();
crypto/tcrypt.c:                end = get_cycles();
crypto/tcrypt.c:                start = get_cycles();
crypto/tcrypt.c:                end = get_cycles();
crypto/tcrypt.c:                start = get_cycles();
crypto/tcrypt.c:                end = get_cycles();
drivers/char/hangcheck-timer.c: return get_cycles();
drivers/char/hangcheck-timer.c: printk("Hangcheck: Using get_cycles().\n");
drivers/char/random.c:  sample.cycles = get_cycles();
drivers/input/joystick/analog.c:#define GET_TIME(x)     do { x = get_cycles(); }
include/linux/arcdevice.h:          _x = get_cycles(); \
include/linux/arcdevice.h:          _y = get_cycles(); \
mm/slub.c:      if (!s->defrag_ratio || get_cycles() % 1024 > s->defrag_ratio)
mm/slub.c:      p += 64 + (get_cycles() & 0xff) * sizeof(void *);
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

iounmap if pci clock is over 33MHz.  Cosmetic because the iomap() in this
case is just a bit of address magic.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Or strange things will happen.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This was crashing the combination of highmem and sparsemem.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The recent switch of the Sibyte SOCs from the processor specific cache
managment code in c-sb1.c to c-r4k.c lost this old hack

    [MIPS] Hack for SB1 cache issues

    Removing flush_icache_page a while ago broke SB1 which was using an empty
    flush_data_cache_page function.  This glues things well enough so a more
    efficient but also more intrusive solution can be found later.
Signed-Off-By: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

in the hope it was no longer needed.  As it turns it still is so resurrect
it until there is a better solution.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [CRYPTO] geode: Fix not inplace encryption

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  mlx4_core: Fix thinko in QP destroy (incorrect bitmap_free)
  RDMA/cxgb3: Set the max_qp_init_rd_atom attribute in query_device
  IB/ehca: Fix static rate calculation
  IB/ehca: Return physical link information in query_port()
  IB/ipath: Fix race with ACK retry timeout list management
  IB/ipath: Fix memory leak in ipath_resize_cq() if copy_to_user() fails
  mlx4_core: Fix possible bad free in mlx4_buf_free()

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/x86:
  x86: enable "make ARCH=x86"
  x86: do not use $(ARCH) when not needed
  kconfig: use $K64BIT to set 64BIT with all*config targets
  kconfig: add helper to set config symbol from environment variable
  kconfig: factor out code in confdata.c
  x86: move the rest of the menu's to Kconfig
  x86: move all simple arch settings to Kconfig
  x86: copy x86_64 specific Kconfig symbols to Kconfig.i386
  x86: add X86_64 dependency to x86_64 specific symbols in Kconfig.x86_64
  x86: add X86_32 dependency to i386 specific symbols in Kconfig.i386
  x86: arch/x86/Kconfig.cpu unification
  x86: start unification of arch/x86/Kconfig.*
  x86: unification of cfufreq/Kconfig

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NET]: rt_check_expire() can take a long time, add a cond_resched()
  [ISDN] sc: Really, really fix warning
  [ISDN] sc: Fix sndpkt to have the correct number of arguments
  [TCP] FRTO: Clear frto_highmark only after process_frto that uses it
  [NET]: Remove notifier block from chain when register_netdevice_notifier fails
  [FS_ENET]: Fix module build.
  [TCP]: Make sure write_queue_from does not begin with NULL ptr
  [TCP]: Fix size calculation in sk_stream_alloc_pskb
  [S2IO]: Fixed memory leak when MSI-X vector allocation fails
  [BONDING]: Fix resource use after free
  [SYSCTL]: Fix warning for token-ring from sysctl checker
  [NET] random : secure_tcp_sequence_number should not assume CONFIG_KTIME_SCALAR
  [IWLWIFI]: Not correctly dealing with hotunplug.
  [TCP] FRTO: Plug potential LOST-bit leak
  [TCP] FRTO: Limit snd_cwnd if TCP was application limited
  [E1000]: Fix schedule while atomic when called from mii-tool.
  [NETX]: Fix build failure added by 2.6.24 statistics cleanup.
  [EP93xx_ETH]: Build fix after 2.6.24 NAPI changes.
  [PKT_SCHED]: Check subqueue status before calling hard_start_xmit

Scrap the local __INLINE__ macro, and rename timeval_cmp to fasttime_cmp.

Inline macro was completely unnecessary since the macro was defined
locally to be inline.
timeval_cmp was inaccurately named since it does comparison on
struct fasttimer_t and not on struct timeval.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add \n\ at end of lines inside asm statement to avoid warning.

No change except adding \n\ to end of line and correcting
whitespace has been done.
Removes warning about multi-line string literals when compiling
arch/cris/arch-v10/lib/memset.c
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add \n\ at end of lines inside asm statement to avoid warning.

No change except adding \n\ to end of line and correcting
whitespace has been done.
Removes warning about multi-line string literals when compiling
arch/cris/arch-v10/lib/string.c
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Removes warning when compiling arch/cris/arch-v10/lib/usercopy.c

No change except adding \n\ on the end of the lines has been done.
Removes warning about multi-line string literals.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Declare mac using DECLARE_MAC_BUF for use when calling print_mac().

This fixes compile error where mac was undeclared.
Also, remove unused variable i.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Include linux/pagemap.h for release_pages and page_cache_release.

Fixes compilation error in arch/cris/mm/init.c when CONFIG_SWAP is unset.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

These are needed due to a cache bug, and can be used to make sure that the
DMA descriptors are flushed to memory and can be safely handled by DMA.

flush_dma_descr - Flush one DMA descriptor.
flush_dma_list - Flush a complete list of DMA descriptors.
cris_flush_cache - Flush the complete cache.
cris_flush_cache_range - Flush only the specified range
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Improve and bugfix CRIS v10 fast timers.

- irq_handler_t now only takes two arguments.
- Keep interrupts disabled as long as we have a reference to the
  fasttimer list and only enable them while doing the callback.
  del_fast_timer may be called from other interrupt context.
- Fix bug where debug code could return without calling local_irq_restore.
- Use jiffies instead of usec (change from struct timeval to fasttime_t).
- Don't initialize static variables to zero.
- Remove obsolete #ifndef DECLARE_WAITQUEUE code.
- fast_timer_init should be __initcall.
- Change status/debug variables to unsigned.
- Remove CVS log and CVS id.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix timer interrupt parameters for CRIS v10.

- irq_handler_t only takes two arguments, use get_irq_regs to get
  regs for profiling.
- Call update_process_times.
- Remove CVS tag.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove MTD_AMDSTD and MTD_OBSOLETE_CHIPS from defconfig, Kconfig and code,
instead we'll use MTD_CFI or MTD_JEDECPROBE.

[akpm@linux-foundation.org: codingl-style cleanups]
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

New and improved serial driver for CRISv10, take three, with improvements
suggested by Jiri Slaby.

- Call wait_event_interruptible with a _correct_ and sensible condition.
- Removed superfluous test of info->flags & ASYNC_CLOSING, since that is done
  by wait_event_interruptible.
- Moved common code for deregistering DMA and IRQ to deinit_port function.
- Use setup_timer when initializing flush_timer.
- Convert bit-field for uses_dma_in and uses_dma_out to regular bytes.
- Removed CVS tags.
- Removed defines and comments for CRIS_BUF_SIZE and TTY_THRESHOLD_THROTTLE
  (no longer used).
- Cleaned up code to pass checkpatch.
- Add crisv10.h header file.
- Merge of CRISv10 from Axis internal CVS.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In file included from include/asm/byteorder.h:23,
                 from include/asm-generic/bitops/le.h:5,
                 from include/asm-generic/bitops/ext2-non-atomic.h:4,
                 from include/asm/bitops.h:163,
                 from include/linux/bitops.h:17,
                 from include/asm/posix_types.h:55,
                 from include/linux/posix_types.h:47,
                 from include/linux/types.h:11,
                 from include/linux/capability.h:16,
                 from include/linux/sched.h:49,
                 from arch/cris/kernel/asm-offsets.c:1:
include/linux/byteorder/little_endian.h:43: parse error before "__cpu_to_le64p"
include/linux/byteorder/little_endian.h:44: warning: return type defaults to `int'
include/linux/byteorder/little_endian.h: In function `__cpu_to_le64p':
include/linux/byteorder/little_endian.h:45: `__le64' undeclared (first use in this function)

Remove include of asm/bitops.h, not needed here, corrects compilation error
(__le64 undeclared).
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I'm converting most array size calculations under arch/ to use
ARRAY_SIZE().  This is the patch for CRIS.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove some unused config lines, and add some others that needs to be off
for a succesful compile. This is the minimal set of changes for 2.6.23.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

- Add __negdi2 to exported symbols.
- Remove string functions from exported symbols.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Include linux/param.h for HZ.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>