In the imx6q-sabreauto and imx6dl-sabreauto boards,
the pin MX6Q{DL}_PAD_EIM_D19 is used as a GPIO for SPI NOR, but
it is used as a data pin for the WEIM NOR.

In order to fix the conflict, this patch removes the pin from the hog,
and adds a new board-level pinctrl: pinctrl_ecspi1_sabreauto.

The SPI NOR selects this pinctrl_ecspi1_sabreauto when it is enabled.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The WEIM(Wireless External Interface Module) works like a bus.
You can attach many different devices on it, such as NOR, onenand.

In the case of i.MX6q-sabreauto, the NOR is connected to WEIM.

This patch also adds the devicetree binding document.
The driver only works when the devicetree is enabled.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add missing pin config
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

use NO_PAD_CTL / 0x80000000 instead of 0x10000 to prevent misconfigured pads
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[Steffen: split up patch into tqma53+mba53 part]
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add properties to make use of pca9554 gpio expander.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Enable the sgtl5000 found on MBa53 mainboard.
Also enable audio muxer and ssi, which are needed for sound to work.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Enable tve on MBa53.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

As the displays are optional and we have more than one, also
set the status of the parallel display and the ldb to disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add WP/CD pinctrl for esdhc2.
Also, add vmmc-supply for esdhc2.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This adds the Television Encoder (TVEv2) device tree node
to the i.MX53 dtsi.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

I2S_MCLK is moved from pad GPIO19 to GPIO0, which can be muxed to the
ssi_ext1 clock signal. #SYSTEM_DOWN is moved from pad GPIO0 to GPIO19.
Add #PHY_RESET and LCD_CONTRAST.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

BIT(31) is NO_PAD_CTL, not BIT(16)
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

It's active high, not active low.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Patch adds initial dts for Phytec PCM970 Rapid development kit.
- Added definition for UART0 and UART1.
- Added additional SPI chipselect which used on RDK for ZegBee module.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

UART1 and UART2 can be unused on some designs with PCM038 module.
Remove these definitions from basic dts and lets choose user only
necessary UARTs in custom designs.
Keep UART0 for using this one as boot console, but since we have
not way to disable usage RTSCTS signals, remove this parameter for UART0.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

PCM038 dts can be used as base for development kit board or any
custom PCB designs. Renames this file to match functionality.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

FEC (KSZ8001L) reset pin is connected to GPIOC30.
Add this definition to dts.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add initial Freescale Vybrid VF610 Tower board support
with uart and fec enabled.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add SoC level device tree source for Freescale Vybrid VF610.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add a group to the fec pinctrl, for use with MII interface.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add ecspi2 pinctrl.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add a group to the cspi pinctrl.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add support for CLAA WVGA display for i.MX53 QSB.
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

With the commit 7f217794 (mmc: dt: Consolidate DT bindings),
the device tree properties used by various device drivers
for SD/MMC host controllers were standardized.  One of the changes
was that the property "fsl,card-wired", previously used by the
Freescale driver, was replaced with "non-removable". Fix the example
documentation regarding this.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

There is a redundant ocotp node.  Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

There is a redundant label on usbmisc node.  Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add initial imx6sl-evk board support with uart, usdhc and fec enabled.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add SoC level device tree source for imx6sl.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Configure the data and tag latency for the L2 cache. This improves the
system performance.

This configuration is taken from Freescale's kernel patch

"ENGR00153601 [MX6]Adjust L2 cache parameter" [1]

which does

writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_TAG_LATENCY_CTRL));
writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_DATA_LATENCY_CTRL));

In this patch we are doing the same via the device tree.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

[1] http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_12.09.01&id=814656410b40c67a10b25300e51b0477b2bb96d1

Since the SPI/NOR has pin conflict with the WEIM NOR,
we disable the spi/nor by default.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The SPI/NOR needs this gpio for CS.
So add this gpio in the hog pinctrl.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The SPI/NOR needs this gpio for CS.
So add this gpio in the hog pinctrl.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

enable the gpmi-nand for imx6q-sabreauto and imx6qdl-sabreauto boards.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

add the pinctrl item for gpmi-nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The gpmi does not use the MX6Q_PAD_NANDF_CS2__NAND_CE2_B and
MX6Q_PAD_NANDF_CS3__NAND_CE3_B.

Just remove them.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Added SPI node and PMIC MC13783 (spi0.0) to imx27-phytec-phycore DT file.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>