- 05 Oct, 2022 9 commits
-
-
Ping-Ke Shih authored
MAC maintains TX FIFO to transmit packets with meta data to BB layer. To debug abnormal transmission, we need to dump the content to dig problem. Since FIFO of 8852C locates on different address with different size and need additional switch to enable read operation, this patch adds the changes accordingly. Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220930134417.10282-2-pkshih@realtek.com
-
Ping-Ke Shih authored
8852CE is a combo chip, and WiFi driver controls pin MUX. To output BT firmware log to specific hardware pin, set pin MUX to achieve. Signed-off-by:
-
Ping-Ke Shih authored
The new BB parameters add new cfg_tpe 4 to improve performance of eFEM modules (rfe_type >= 50), but we are using iFEM modules for now, so this warning can be ignored. Signed-off-by:
-
Ping-Ke Shih authored
Update BB parameters along with internal tag HALBB_027_067_07. Signed-off-by:
-
Ping-Ke Shih authored
Using mdelay() can work well, but calibration causes too much time. Use proper udelay() to get shorter time and the same result. Signed-off-by:
-
Ping-Ke Shih authored
IQK can change the values of this register set, so need to backup and restore the values. During we rewrite IQK, the policy is changed. Some values are controlled and filled by IQK, and don't need to restore after IQK. Therefore, remove this kind of registers from this array. Signed-off-by:
-
Prasanna Kerekoppa authored
Fixes the ap interface delete issue. Fix is to make sure interface is created with supported version. Patch has been verified by creating and deleting AP interface. Signed-off-by:
Prasanna Kerekoppa <prasanna.kerekoppa@infineon.com> Signed-off-by:
Ian Lin <ian.lin@infineon.com> Signed-off-by:
-
Wright Feng authored
To create virtual station interface for RSDB and VSDB, we add interface creation version 1, 2 and 3 supports The structures of each version are different and only version 3 and later version are able to get interface creating version from firmware side. The patch has been verified two concurrent stations pings test with interface create version 1: 89342(4359b1)-PCIE: 9.40.100 interface create version 2: 4373a0-sdio: 13.10.271 interface create version 3: 4373a0-sdio: 13.35.48 Signed-off-by:Wright Feng <wright.feng@cypress.com> Signed-off-by:
Chi-hsien Lin <chi-hsien.lin@infineon.com> Signed-off-by:
-
Wright Feng authored
With RSDB device, it is able to control two station interfaces concurrently. So we add creating station interface support and allow user to create it via cfg80211. Signed-off-by:
-
- 04 Oct, 2022 18 commits
-
-
Wright Feng authored
To enhance FW debugging, we add dongle memory dump when hitting attaching failure with PCIE bus. It can help developer to get more information about dongle trap reason and root cause. Signed-off-by:
Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by:
-
Wright Feng authored
When firmware hit trap at initialization, host will read abnormal max_flowrings number from dongle, and it will cause kernel panic when doing iowrite to initialize dongle ring. To detect this error at early stage, we directly return error when getting invalid max_flowrings(>256). Signed-off-by:
-
Wright Feng authored
Currently, host only reads console buffer when receiving mailbox data or hit crash with PCIE bus. Therefore, we add timer in PCIE code to read console buffer periodically to help developer and user check firmware message when there is no data transmission between host and dongle. Signed-off-by:
-
Ramesh Rangavittal authored
Auto Channel Select feature of HostAP uses dump_survey to fetch OBSS statistics. When the device is in the middle of an authentication sequence or just at the end of authentication completion, running dump_survey would trigger a channel change. The channel change in-turn can cause packet loss, resulting in authentication delay. With this change, dump_survey won't be run when authentication or association is in progress, hence resolving the issue. Signed-off-by:
Ramesh Rangavittal <ramesh.rangavittal@infineon.com> Signed-off-by:
Chung-Hsien Hsu <chung-hsien.hsu@infineon.com> Signed-off-by:
-
Double Lo authored
This patch fix CERT-P2P:5.1.10 failure at step 18 Group formation failed due to chip is under dump survey. Decrease the dump survery duration to pass this certification case. Signed-off-by:
Double Lo <double.lo@cypress.com> Signed-off-by:
-
Wright Feng authored
When doing dump_survey, host will call "dump_obss" iovar to firmware side. Host need to make sure the HW clock in dongle is on, or there is high probability that firmware gets trap because register or shared memory access failed. To fix this, we disable mpc when doing dump obss and set it back after that. [28350.512799] brcmfmac: brcmf_dump_obss: dump_obss error (-52) [28743.402314] ieee80211 phy0: brcmf_fw_crashed: Firmware has halted or crashed [28745.869430] brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout [28745.877546] brcmfmac: brcmf_sdio_checkdied: firmware trap in dongle Signed-off-by:
-
Wright Feng authored
To enable ACS feature in Hostap daemon, dump_survey cfg80211 ops and dump obss survey command in firmware side are needed. This patch is for adding dump_survey feature and adding DUMP_OBSS feature flag to check if firmware supports dump_obss iovar. Signed-off-by:
-
Bitterblue Smith authored
Re-enable the function rtl8xxxu_gen2_report_connect. It informs the firmware when connecting to a network. This makes the firmware enable the rate control, which makes the upload faster. It also informs the firmware when disconnecting from a network. In the past this made reconnecting impossible because it was sending the auth on queue 0x7 (TXDESC_QUEUE_VO) instead of queue 0x12 (TXDESC_QUEUE_MGNT): wlp0s20f0u3: send auth to 90:55:de:__:__:__ (try 1/3) wlp0s20f0u3: send auth to 90:55:de:__:__:__ (try 2/3) wlp0s20f0u3: send auth to 90:55:de:__:__:__ (try 3/3) wlp0s20f0u3: authentication with 90:55:de:__:__:__ timed out Probably the firmware disables the unnecessary TX queues when it knows it's disconnected. However, this was fixed in commit edd5747a ("wifi: rtl8xxxu: Fix skb misuse in TX queue selection"). Fixes: c59f13bb ("rtl8xxxu: Work around issue with 8192eu and 8723bu devices not reconnecting") Signed-off-by:
Bitterblue Smith <rtl8821cerfe2@gmail.com> Signed-off-by:
-
Bitterblue Smith authored
This chip is found in the cheapest USB adapters, e.g. 1.17 USD with VAT and shipping from China included. It's a gen 2 chip, similar to the RTL8723BU, but without Bluetooth. Features: 2.4 GHz, b/g/n mode, 1T1R, 150 Mbps. The vendor driver rtl8188fu version 4.3.23.6_20964.20170110 [0] was used as reference. The CD shipped with the device includes a newer driver, version 5.11.5-1-g12f7cde4b.20201102, but that one couldn't complete the WPA2 key exchange thing for whatever reason. [0] https://github.com/kelebek333/rtl8188fuSigned-off-by:
-
Ping-Ke Shih authored
8852BE has two variants with different ID. One is 10ec:b852 that is a main model with 2x2 antenna, and the other is 10ec:b85b that is a 1x1 model. Signed-off-by:
-
Ping-Ke Shih authored
This efuse region is to store PHY calibration, and it is a separated region from the region that stores MAC address. Then, use these data to configure via chip_ops::power_trim that is a calibration mechanism of TX power. Signed-off-by:
-
Ping-Ke Shih authored
efuse stores individual data about a chip itself, such as MAC address, country code, RF and crystal calibration data, and so on. Define a struct to help access efuse content, and copy them into a common struct. Signed-off-by:
-
Ping-Ke Shih authored
This chip_ops is to set TX power according to country, channel, rate and so on. Since shared code is used to configure TX power, we only implement specific part in this patch. Signed-off-by:
-
Zong-Zhe Yang authored
Previously, value of each field is just shown as unsigned. Now, we start to show them with sign to make things more intuitive during debugging. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Zong-Zhe Yang authored
Previously, we thought control registers or setting things for TX power series may change according to chip. So, setting functions are implemented chip by chip. However, until now, the functions keep the same among chips, at least 8852A, 8852C, and 8852B. There is a sufficient number of chips to share generic setting functions. So, we now remake them including TX power by rate, TX power offset, TX power limit, and TX power limit RU as generic ones in phy.c. Besides, there are some code refinements in the generic ones, but almost all of the logic doesn't change. Signed-off-by:
-
Ping-Ke Shih authored
These tables are used by RFK to assist to configure PHY and RF registers. Signed-off-by:
-
Ping-Ke Shih authored
These tables contain BB and RF parameters that driver will load them into registers. It also contains TX power according to country, band, rate and so on. Increasing thermal can cause TX power degraded, so power tracking tables are defined to compensate TX power. Internal version of these tables: - HALRF_029_00_014 (R32) - HALBB_027_046_05 Signed-off-by:
-
Ping-Ke Shih authored
These tables contain BB and RF parameters that driver will load them into registers. It also contains TX power according to country, band, rate and so on. Increasing thermal can cause TX power degraded, so power tracking tables are defined to compensate TX power. Internal version of these tables: - HALRF_029_00_014 (R32) - HALBB_027_046_05 Signed-off-by:
-
- 30 Sep, 2022 13 commits
-
-
Jakub Kicinski authored
Merge tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.1 Few stack changes and lots of driver changes in this round. brcmfmac has more activity as usual and it gets new hardware support. ath11k improves WCN6750 support and also other smaller features. And of course changes all over. Note: in early September wireless tree was merged to wireless-next to avoid some conflicts with mac80211 patches, this shouldn't cause any problems but wanted to mention anyway. Major changes: mac80211 - refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO) feature continues brcmfmac - support CYW43439 SDIO chipset - support BCM4378 on Apple platforms - support CYW89459 PCIe chipset rtw89 - more work to get rtw8852c supported - P2P support - support for enabling and disabling MSDU aggregation via nl80211 mt76 - tx status reporting improvements ath11k - cold boot calibration support on WCN6750 - Target Wake Time (TWT) debugfs support for STA interface - support to connect to a non-transmit MBSSID AP profile - enable remain-on-channel support on WCN6750 - implement SRAM dump debugfs interface - enable threaded NAPI on all hardware - WoW support for WCN6750 - support to provide transmit power from firmware via nl80211 - support to get power save duration for each client - spectral scan support for 160 MHz wcn36xx - add SNR from a received frame as a source of system entropy * tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (231 commits) wifi: rtl8xxxu: Improve rtl8xxxu_queue_select wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM wifi: rtl8xxxu: gen2: Enable 40 MHz channel width wifi: rtw89: 8852b: configure DLE mem wifi: rtw89: check DLE FIFO size with reserved size wifi: rtw89: mac: correct register of report IMR wifi: rtw89: pci: set power cut closed for 8852be wifi: rtw89: pci: add to do PCI auto calibration wifi: rtw89: 8852b: implement chip_ops::{enable,disable}_bb_rf wifi: rtw89: add DMA busy checking bits to chip info wifi: rtw89: mac: define DMA channel mask to avoid unsupported channels wifi: rtw89: pci: mask out unsupported TX channels iwlegacy: Replace zero-length arrays with DECLARE_FLEX_ARRAY() helper ipw2x00: Replace zero-length array with DECLARE_FLEX_ARRAY() helper wifi: iwlwifi: Track scan_cmd allocation size explicitly brcmfmac: Remove the call to "dtim_assoc" IOVAR brcmfmac: increase dcmd maximum buffer size brcmfmac: Support 89459 pcie brcmfmac: increase default max WOWL patterns to 16 cw1200: fix incorrect check to determine if no element is found in list ... ==================== Link: https://lore.kernel.org/r/20220930150413.A7984C433D6@smtp.kernel.orgSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Saeed Mahameed says: ==================== mlx5 xsk updates part2 2022-09-28 XSK buffer improvements, This is part #2 of 4 parts series. 1) Expose xsk min chunk size to drivers, to allow the driver to adjust to a better buffer stride size 2) Adjust MTT page size to the XSK frame size, to avoid umem overrun in certain situations. 3) Use xsk frame size as the striding RQ page size for XSK RQs 4) KSM for unaligned XSK, KSM allows arbitrary buffer chunk lengths registration in HW, which makes more sense for unaligned XSK. 4) More cleanups and optimizations in preparation for next improvements in part3 part 1: https://lore.kernel.org/netdev/20220927203611.244301-1-saeed@kernel.org/ ==================== Link: https://lore.kernel.org/r/20220929072156.93299-1-saeed@kernel.orgSigned-off-by: -
Maxim Mikityanskiy authored
Although mlx5e_rq_free_shampo can be called unconditionally, it belongs to case MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ. Move it there to allow to add more init/cleanup actions to the striding RQ case. If xdp_rxq_info_reg_mem_model fails, don't forget to destroy the page pool. Signed-off-by:
Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by:
Saeed Mahameed <saeedm@nvidia.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
-
Maxim Mikityanskiy authored
The same clear_bit is called in both error and success flows. Move the call to do it only once and remove the out label. Signed-off-by:
-
Maxim Mikityanskiy authored
To decrease the nesting level and reduce duplication of code, create functions to redirect direct RQTs to the actual RQs or drop_rq, which are used in the activation and deactivation flows of channels. Signed-off-by:
-
Maxim Mikityanskiy authored
mlx5e_xsk_page_alloc_pool became a thin wrapper around xsk_buff_alloc. Drop it and call xsk_buff_alloc directly. Signed-off-by:
-
Maxim Mikityanskiy authored
struct mlx5e_alloc_unit consists of a single union. Convert it to a union itself to simplify casting it to struct xdp_buff *, which will be used to implement XSK batching on striding RQ. Signed-off-by:
-
Maxim Mikityanskiy authored
mlx5e_alloc_unit stores the DMA address and a pointer to either struct page (regular RQ) or struct xdp_buff (XSK RQ). This DMA address is redundant, because when a page or an XSK frame is allocated, the same address is also stored there. Some flows take the address from struct mlx5e_alloc_unit, and some take it from struct page or xdp_buff. This commit removes the address from struct mlx5e_alloc_unit, which makes it twice as small and improves locality (this struct is used in an array), also saving on unnecessary stores to the addr field. Almost all flows know unambiguously whether the DMA address should be taken from page or from xdp_buff. The exception is the allocation flows, where a new branch appeared, which will be optimized out in the next commits. struct mlx5e_alloc_unit used to be called mlx5e_dma_info. Signed-off-by:
-
Maxim Mikityanskiy authored
The next commit will remove the DMA address from the struct currently called mlx5e_dma_info, because the same value can be retrieved with page_pool_get_dma_addr(page) in almost all cases, with the notable exception of SHAMPO (HW GRO implementation) that modifies this address on the fly, after the initial allocation. To keep the SHAMPO logic intact, struct mlx5e_dma_info remains in the SHAMPO code, consisting of addr and page (XSK is not compatible with SHAMPO). The struct used in all other places is renamed to mlx5e_alloc_unit, allowing the next commit to remove the addr field without affecting SHAMPO. The new name means "allocation unit", and it's more appropriate after the field with the DMA address gets removed. Signed-off-by:
-
Maxim Mikityanskiy authored
RX page cache stores dma_info structs, that consist of a pointer to struct page and a DMA address. In fact, the DMA address is extracted from struct page using page_pool_get_dma_addr when a page is pushed to the cache. By moving this call to the point when a page is popped from the cache, we can avoid storing the DMA address in the cache, effectively reducing its size by two times without losing any functionality. Signed-off-by:
-
Maxim Mikityanskiy authored
WQEs must not cross page boundaries, they are padded with NOPs if they don't fit the page. mlx5e_mpwrq_total_umr_wqebbs doesn't take into account this padding, risking reserving not enough space. The padding is not straightforward to add to this calculation, because WQEs of different sizes may be mixed together in the queue. If each page ends with a big WQE that doesn't fit and requires at most its size minus 1 WQEBB of padding, the total space can be much bigger than in case when smaller WQEs take advantage of this padding. Replace the wrong exact calculation by the following estimation. Each padding can be at most the size of the maximum WQE used in the queue minus one WQEBB. Let's call the rest of the page "useful space". If we divide the total size of all needed WQEs by this useful space, rounding up, we'll get the number of pages, which is enough to contain all these WQEs. It's correct, because every WQE that appeared on the boundary between two blocks of useful space would start in the useful space of one page and end in the padding of the same page, while our estimation reserved space for its tail in the next space, making the estimation not smaller than the real space occupied in the queue. The code actually uses a looser estimation: instead of taking the maximum size of all used WQE types minus 1 WQEBB, it takes the maximum hardware size of a WQE. It's made for simplicity and extensibility. Signed-off-by:
-
Maxim Mikityanskiy authored
The previous commit removed the last usage of xsk_buff_discard in mlx5e, so the function that is no longer used can be removed. Signed-off-by:
-
Maxim Mikityanskiy authored
UMR MTTs used in striding RQ have certain alignment requirements. While it's guaranteed to work when UMR pages are aligned to the UMR page size, in practice it works then UMR pages are aligned to 8 bytes. However, it's still not enough flexibility for the unaligned mode of XSK. This patch leverages KSM to map UMR pages without alignment requirements, when unaligned XSK is active. The downside is that KSM entries are twice as big as MTTs, which limits the maximum WQE size, so regular RQs and aligned XSK continue using MTTs. Signed-off-by:
-
