- 25 Aug, 2013 2 commits
-
-
Vikas Sajjan authored
Moves the RTC DT node's "status" property from exynos5250 board (arndale & snow) dts files to exynos5250.dtsi, since the bindings in exynos5250.dtsi depicts the RTC h/w completely. Signed-off-by:
Vikas Sajjan <vikas.sajjan@linaro.org> Reviewed-by:
Tomasz Figa <t.figa@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Vikas Sajjan authored
Fixes the RTC DT node name for Exynos5250 as per the DT node naming convention. Signed-off-by:
-
- 18 Aug, 2013 17 commits
-
-
Dongjin Kim authored
This patch adds EHCI and OHCI host device nodes for Exynos4. Signed-off-by:
Dongjin Kim <tobetter@gmail.com> Acked-by:
Jingoo Han <jg1.han@samsung.com> Reviewed-by:
-
Andrew Bresticker authored
This adds device-tree bindings for the audio subsystem clock controller on Exynos 5420. Signed-off-by:
Andrew Bresticker <abrestic@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/57712Reviewed-by:
Simon Glass <sjg@chromium.org> Signed-off-by:
Padmavathi Venna <padma.v@samsung.com> Signed-off-by:
-
Padmavathi Venna authored
This patch corrects the /include to #include on exynos5420 Signed-off-by:
-
Arun Kumar K authored
The patch adds MFC nodes for exynos 5420. Signed-off-by:
Arun Kumar K <arun.kk@samsung.com> Signed-off-by:
-
Arun Kumar K authored
The patch adds the MFC clock entry for the 5250 SoC. Signed-off-by:
-
Arun Kumar K authored
Removes the unused sclk_mfc from exynos4 dtsi file. Signed-off-by:
-
Arun Kumar K authored
MFC driver is updated to use only one clock instead of two. Correcting this in the binding documentation. Signed-off-by:
-
Mark Brown authored
While the Linux driver stack is capable of figuring this out for itself document the fact that we really do use the internal PHY even with the directly wired hub on the board to save anyone else having to work this out for themselves. Signed-off-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
-
Mark Brown authored
The Arndale has a SMSC USB3503 connected in hardware only mode like a PHY, support it using the usb-nop-xceiv binding. Note that due to a regrettable decision to use a regulator to represent the reset signal this uses a fixed voltage regulator to do that, there is a plan to use the reset controller binding once that is merged so it does not seem worthwhile to fix the usb-nop-xceiv driver at this point. Signed-off-by:
Tushar Behera <tushar.behera@linaro.org> Signed-off-by:
-
Tushar Behera authored
OrigenQuad board boots with secure firmware support. Enable support for reading smc commands. The binding has been updated as per the documentation provided in Documentation/devicetree/bindings/arm/samsung-boards.txt. Signed-off-by:
-
Vikas Sajjan authored
Add pin state information for DP HPD support that requires pin configuration support using pinctrl interface. Signed-off-by:
-
Vikas Sajjan authored
Adds DP controller DT node to exynos5420 SoC Signed-off-by:
-
Vikas Sajjan authored
Moves the properties of DP controller to exynos5.dtsi which are common across exynos5 SoCs like Exynos5250 and Exynos5420. The PHY DP Node is based on Jingoo Han's <jg1.han@samsung.com> patch at https://patchwork.linuxtv.org/patch/19189/Signed-off-by:
-
Vikas Sajjan authored
Adds FIMD DT node to exynos5420 based SMDK. Also adds display-timimg information node. Signed-off-by:
-
Yadwinder Singh Brar authored
Add DT nodes for gsc, isp, mfc, disp, mau, g2d and msc PM domains. Signed-off-by:
Yadwinder Singh Brar <yadi.brar@samsung.com> Signed-off-by:
-
Vikas Sajjan authored
Moves the properties of FIMD DT node which are common across Exynos5 based SoCs like Exynos5250 and Exynos5420 to exynos5.dtsi Signed-off-by:
-
Vikas Sajjan authored
As the display-timing information is parsed by FIMD driver, it makes sense to move the display-timing DT node inside FIMD DT node for exynos5250 Signed-off-by:
-
- 06 Aug, 2013 5 commits
-
-
Andrzej Hajda authored
Add MAX8998 LDO12 and fixed voltage regulator nodes. While at it, all fixed voltage regulator nodes are grouped in a 'regulators' node. Signed-off-by:
Andrzej Hajda <a.hajda@samsung.com> Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by:
-
Andrzej Hajda authored
Add pinctrl nodes for the camera parallel port CAM_A data bus and the CAM_A_CLKOUT clock output pin. Signed-off-by:
-
Sylwester Nawrocki authored
Enable FIMC devices on the Trats board. This allows using the device in memory-to-memory mode only. The camera port pinctrl property is now empty and will be updated while support for the camera sensors is added. Signed-off-by:
-
Sylwester Nawrocki authored
Add common camera node and detailed properties for the Exynos4210 FIMC devices. Signed-off-by:
-
Andrzej Hajda authored
This patch add dts entries required for the SPI bus used for firware upload by the S5C73M3 camera. Signed-off-by:
-
- 05 Aug, 2013 8 commits
-
-
Sylwester Nawrocki authored
This patch enables the front camera using the internal camera ISP (FIMC-IS). Signed-off-by:
-
Jacek Anaszewski authored
This patch adds AK8975 magnetometer node and corresponding i2c-gpio bus node for TRATS2 board. Signed-off-by:
Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by:
-
Sylwester Nawrocki authored
Add common camera node and Exynos4212/4412 specific nodes for FIMC, MIPI-CSIS, FIMC-LITE and FIMC-IS devices. Signed-off-by:
-
Sylwester Nawrocki authored
This patch adds common Exynos4 SoC series FIMC and MIPI CSIS device nodes. Signed-off-by:
-
Sylwester Nawrocki authored
The Exynos4 SPI controller has migrated to the generic DMA bindings since commit b5be04d3("spi: s3c64xx: Modify SPI driver to use generic DMA DT support"). Use the generic bindings to specify the corresponding DMA to make the SPI usable again on Exynos4x12 SoCs. Signed-off-by:
-
Sylwester Nawrocki authored
The ISP power domain is a common power domain for FIMC-LITE and FIMC-IS (camera ISP) devices. Signed-off-by:
-
Sylwester Nawrocki authored
Add pinctrl nodes for the ISP I2C0, ISP I2C1 and ISP UART devices. Signed-off-by:
-
Sylwester Nawrocki authored
Add separate nodes for the CAMCLK pin and turn off pull-up on camera ports A, B. The video bus pins and the clock output (CAMCLK) pin need separate nodes since full camera port is not used in some configurations, e.g. for MIPI CSI-2 bus only CAMCLK is required and data/clock signal use separate dedicated pins. Signed-off-by:
-
- 31 Jul, 2013 1 commit
-
-
Sachin Kamat authored
Adds G2D node to exynos5250 DT file. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
- 24 Jul, 2013 7 commits
-
-
Amit Daniel Kachhap authored
This patch adds device node for TMU controller. There are 3 instances of the controllers so 3 nodes are created. Acked-by:
Jonghwa Lee <jonghwa3.lee@samsung.com> Reviewed-by:
Eduardo Valentin <eduardo.valentin@ti.com> Signed-off-by:
Amit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by:
-
Tomasz Figa authored
This patch introduces device tree sources for Samsung Trats 2 board based on Exynos4412 SoC. Currently support includes: - eMMC, - main PMIC (max77686), - serial ports, - GPIO keys, - touchscreen. Signed-off-by:
-
Kukjin Kim authored
Re-ordering in alphabetical. Signed-off-by: -
Mark Brown authored
The default audio module for the Arndale has a WM1811A on it. Add this to the device tree bindings. Signed-off-by:
-
Mark Brown authored
As part of this add nodes for the main wall supply as well as bucks 7 and 8 which are used to drop that down for several of the LDOs. Signed-off-by:
-
Mark Brown authored
Fixed voltage regulators (and other similar free standing things) are supposed to go on a simple-bus for DT correctness reasons. Signed-off-by:
-
Mark Brown authored
The out of tree code configures a pullup on the line indicating that it is an active low interrupt. Signed-off-by:
-
