When subfunction VSI is open the same code as for PF VSI should be
executed. Also when up is complete. Reflect that in code by adding
subfunction VSI to consideration.

In case of stopping, PF doesn't have additional tasks, so the same
is with subfunction VSI.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Implement devlink port handlers responsible for ethernet type devlink
subfunctions. Create subfunction devlink port and setup all resources
needed for a subfunction netdev to operate. Configure new VSI for each
new subfunction, initialize and configure interrupts and Tx/Rx resources.
Set correct MAC filters and create new netdev.

For now, subfunction is limited to only one Tx/Rx queue pair.

Only allocate new subfunction VSI with devlink port new command.
Allocate and free subfunction MSIX interrupt vectors using new API
calls with pci_msix_alloc_irq_at and pci_msix_free_irq.

Support both automatic and manual subfunction numbers. If no subfunction
number is provided, use xa_alloc to pick a number automatically. This
will find the first free index and use that as the number. This reduces
burden on users in the simple case where a specific number is not
required. It may also be slightly faster to check that a number exists
since xarray lookup should be faster than a linear scan of the dyn_ports
xarray.
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Make some of the netdevice_ops functions visible from outside for
another VSI type created netdev.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add required plumbing for new VSI type dedicated to devlink subfunctions.
Make sure that the vsi is properly configured and destroyed. Also allow
loading XDP and AF_XDP sockets.

The first implementation of devlink subfunctions supports only one Tx/Rx
queue pair per given subfunction.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Gal Pressman says:

====================
RX software timestamp for all - round 2

Round 1 of drivers conversion was merged [1], this is round 2, more
drivers to follow.

[1] https://lore.kernel.org/netdev/20240901112803.212753-1-gal@nvidia.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pieter Van Trappen says:

====================
net: dsa: microchip: rename and clean ksz8 series files

The first KSZ8 series implementation was done for a KSZ8795 device but
since several other KSZ8 devices have been added. Rename these files
to adhere to the ksz8 naming convention as already used in most
functions and the existing ksz8.h; add an explanatory note.

In addition, clean the files by removing macros that are defined at
more than one place and remove confusion by renaming the KSZ8830
string which in fact is not an existing KSZ series switch.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
---
v4:
 - correct once more Kconfig list of supported switches

v3: https://lore.kernel.org/netdev/20240903072946.344507-1-vtpieter@gmail.com/
 - rename all KSZ8830 to KSZ88X3 only (not KSZ8863)
 - update Kconfig as per Arun's suggestion

v2: https://lore.kernel.org/netdev/20240830141250.30425-1-vtpieter@gmail.com/
 - more finegrained description in Kconfig and ksz8.c header
 - add KSZ8830/ksz8830 to KSZ8863/ksz88x3 renaming

v1: https://lore.kernel.org/netdev/20240828102801.227588-1-vtpieter@gmail.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace ksz8830 with ksz88x3 for CHIP_ID definition and other
strings. This due to KSZ8830 not being an actual switch but the Chip
ID shared among KSZ8863/8873 switches, impossible to differentiate
from their Chip ID or Revision ID registers.

Now all KSZ*_CHIP_ID macros refer to actual, existing switches which
removes confusion.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove macros that are already defined at more appropriate places.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The first KSZ8 series implementation was done for a KSZ8795 device but
since several other KSZ8 devices have been added. Rename these files
to adhere to the ksz8 naming convention as already used in most
functions and the existing ksz8.h; add an explanatory note.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Justin Lai says:

====================
Add Realtek automotive PCIe driver

This series includes adding realtek automotive ethernet driver
and adding rtase ethernet driver entry in MAINTAINERS file.

This ethernet device driver for the PCIe interface of
Realtek Automotive Ethernet Switch,applicable to
RTL9054, RTL9068, RTL9072, RTL9075, RTL9068, RTL9071.
====================

Link: https://patch.msgid.link/20240904032114.247117-1-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add myself and Larry Chiu as the maintainer for the rtase ethernet driver.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-14-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

1. Add the RTASE entry in the Kconfig.
2. Add the CONFIG_RTASE entry in the Makefile.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-13-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add a Makefile in the rtase folder to build rtase driver.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-12-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Implement the ethtool function to support users to obtain network card
information, including obtaining various device settings, Report whether
physical link is up, Report pause parameters, Set pause parameters,
Return extended statistics about the device.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-11-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Implement the pci_driver suspend function to enable the device
to sleep, and implement the resume function to enable the device
to resume operation.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-10-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

1. Implement .ndo_set_rx_mode so that the device can change address
list filtering.
2. Implement .ndo_set_mac_address so that mac address can be changed.
3. Implement .ndo_change_mtu so that mtu can be changed.
4. Implement .ndo_tx_timeout to perform related processing when the
transmitter does not make any progress.
5. Implement .ndo_get_stats64 to provide statistics that are called
when the user wants to get network device usage.
6. Implement .ndo_vlan_rx_add_vid to register VLAN ID when the device
supports VLAN filtering.
7. Implement .ndo_vlan_rx_kill_vid to unregister VLAN ID when the device
supports VLAN filtering.
8. Implement the .ndo_setup_tc to enable setting any "tc" scheduler,
classifier or action on dev.
9. Implement .ndo_fix_features enables adjusting requested feature flags
based on device-specific constraints.
10. Implement .ndo_set_features enables updating device configuration to
new features.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-9-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Implement rx_handler to read the information of the rx descriptor,
thereby checking the packet accordingly and storing the packet
in the socket buffer to complete the reception of the packet.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-8-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Implement .ndo_start_xmit function to fill the information of the packet
to be transmitted into the tx descriptor, and then the hardware will
transmit the packet using the information in the tx descriptor.
In addition, we also implemented the tx_handler function to enable the
tx descriptor to be reused.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-7-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Implement rtase_hw_config to set default hardware settings, including
setting interrupt mitigation, tx/rx DMA burst, interframe gap time,
rx packet filter, near fifo threshold and fill descriptor ring and
tally counter address, and enable flow control. When filling the
rx descriptor ring, the first group of queues needs to be processed
separately because the positions of the first group of queues are not
regular with other subsequent groups. The other queues are all newly
added features, but we want to retain the original design. So they were
not put together.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-6-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

1. Implement rtase_interrupt to handle txQ0/rxQ0, txQ4~txQ7 interrupts,
and implement rtase_q_interrupt to handle txQ1/rxQ1, txQ2/rxQ2 and
txQ3/rxQ3 interrupts.
2. Implement rtase_poll to call ring_handler to process the tx or
rx packet of each ring. If the returned value is budget,it means that
there is still work of a certain ring that has not yet been completed.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-5-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Implement the rtase_down function to disable hardware setting
and interrupt and clear descriptor ring.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-4-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Implement the .ndo_open function to set default hardware settings
and initialize the descriptor ring and interrupts. Among them,
when requesting interrupt, because the first group of interrupts
needs to process more events, the overall structure and interrupt
handler will be different from other groups of interrupts, so it
needs to be handled separately. The first set of interrupt handlers
need to handle the interrupt status of RXQ0 and TXQ0, TXQ4~7,
while other groups of interrupt handlers will handle the interrupt
status of RXQ1&TXQ1 or RXQ2&TXQ2 or RXQ3&TXQ3 according to the
interrupt vector.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-3-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for a pci table in this module, and implement pci_driver
function to initialize this driver, remove this driver, or shutdown
this driver.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20240904032114.247117-2-justinlai0215@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Cross-merge networking fixes after downstream PR.

Conflicts:

drivers/net/phy/phy_device.c
  2560db6e ("net: phy: Fix missing of_node_put() for leds")
  1dce520a ("net: phy: Use for_each_available_child_of_node_scoped()")
https://lore.kernel.org/20240904115823.74333648@canb.auug.org.au

Adjacent changes:

drivers/net/ethernet/xilinx/xilinx_axienet.h
drivers/net/ethernet/xilinx/xilinx_axienet_main.c
  858430db ("net: xilinx: axienet: Fix race in axienet_stop")
  76abb5d6 ("net: xilinx: axienet: Add statistics support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fill another small gap in the nftables spec so that it is possible to
dump a tailscale ruleset with:

  tools/net/ynl/cli.py --spec \
     Documentation/netlink/specs/nftables.yaml --dump getrule

This adds support for the 'target' expression.
Signed-off-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20240904091024.3138-1-donald.hunter@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>