- 22 May, 2015 22 commits
-
-
Pavel Machek authored
commit 1819e303 upstream. N900 audio recording needs that codec provides bias voltage for integrated digital microphone and headset microphone depending which one is used. Digital microphone uses 2 V bias and it comes from the codec A part. Codec B part drives the headset microphone bias and that is set to 2.5 V. Signed-off-by:
Pavel Machek <pavel@ucw.cz> [Jarkko: Headset mic bias changed to 2 (2.5 V) as it was before commit e2e8bfdf ("ASoC: tlv320aic3x: Convert mic bias to a supply widget")] Signed-off-by:
Jarkko Nikula <jarkko.nikula@bitmer.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Tony Lindgren authored
commit 102bcb6e upstream. If we use a combination of VMODE and I2C4 for retention modes, eventually the off idle power consumption will creep up by about 23mW, even during off mode with I2C4 always staying enabled. Turns out this is because of erratum i531 "Extra Power Consumed When Repeated Start Operation Mode Is Enabled on I2C Interface Dedicated for Smart Reflex (I2C4)" as pointed out by Nishanth Menon <nm@ti.com>. Let's fix the issue by adding i2c_cfg_clear_mask for the bits to clear when initializing the I2C4 adapter so we can clear SREN bit that drives the I2C4 lines low otherwise when there is no traffic. Fixes: 3b8c4ebb ("ARM: OMAP3: Fix idle mode signaling for sys_clkreq and sys_off_mode") Cc: Kevin Hilman <khilman@kernel.org> Cc: Tero Kristo <t-kristo@ti.com> Reviewed-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
-
Witold Szczeponik authored
commit 622532bb upstream. Commit eec15edb (ACPI / PNP: use device ID list for PNPACPI device enumeration) changed the way how ACPI devices are enumerated and when they are added to the PNP bus. However, it broke the sound card support on (at least) a vintage IBM ThinkPad 600E: with said commit applied, two of the necessary "CSC01xx" devices are not added to the PNP bus and hence can not be found during the initialization of the "snd-cs4236" module. As a consequence, loading "snd-cs4236" causes null pointer exceptions. The attached patch fixes the problem end re-enables sound on the IBM ThinkPad 600E. Fixes: eec15edb (ACPI / PNP: use device ID list for PNPACPI device enumeration) Signed-off-by:
Witold Szczeponik <Witold.Szczeponik@gmx.net> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Chris Bainbridge authored
commit 3349fb64 upstream. Commit 7bc5a2ba 'ACPI: Support _OSI("Darwin") correctly' caused the MacBook firmware to expose the SBS, resulting in intermittent hangs of several minutes on boot, and failure to detect or report the battery. Fix this by adding a 5 us delay to the start of each SMBUS transaction. This timing is the result of experimentation - hangs were observed with 3 us but never with 5 us. Fixes: 7bc5a2ba 'ACPI: Support _OSI("Darwin") correctly' Link: https://bugzilla.kernel.org/show_bug.cgi?id=94651Signed-off-by:
Chris Bainbridge <chris.bainbridge@gmail.com> [ rjw: Subject and changelog ] Signed-off-by:
-
Johan Hovold authored
commit 483d8211 upstream. Unregister GPIOs requested through sysfs at chip remove to avoid leaking the associated memory and sysfs entries. The stale sysfs entries prevented the gpio numbers from being exported when the gpio range was later reused (e.g. at device reconnect). This also fixes the related module-reference leak. Note that kernfs makes sure that any on-going sysfs operations finish before the class devices are unregistered and that further accesses fail. The chip exported flag is used to prevent gpiod exports during removal. This also makes it harder to trigger, but does not fix, the related race between gpiochip_remove and export_store, which is really a race with gpiod_request that needs to be addressed separately. Also note that this would prevent the crashes (e.g. NULL-dereferences) at reconnect that affects pre-3.18 kernels, as well as use-after-free on operations on open attribute files on pre-3.14 kernels (prior to kernfs). Fixes: d8f388d8 ("gpio: sysfs interface") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Hans Verkuil authored
commit 2a700d8e upstream. Various formats had their byte ordering implemented incorrectly, and the V4L2_PIX_FMT_UYVY is actually impossible to create, instead you get V4L2_PIX_FMT_YVYU. This was working before commit ad6ac452 ("add new formats support for marvell-ccic driver"). That commit broke the original format support and the OLPC XO-1 laptop showed wrong colors ever since (if you are crazy enough to attempt to run the latest kernel on it, like I did). The email addresses of the authors of that patch are no longer valid, so without a way to reach them and ask them about their test setup I am going with what I can test on the OLPC laptop. If this breaks something for someone on their non-OLPC setup, then contact the linux-media mailinglist. My suspicion however is that that commit went in untested. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Acked-by:
Jonathan Corbet <corbet@lwn.net> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Marek Vasut authored
commit 4ada77e3 upstream. Fix a typo in the TX DMA interrupt name for AUART4. This patch makes AUART4 operational again. Signed-off-by:
Marek Vasut <marex@denx.de> Fixes: f30fb03d ("ARM: dts: add generic DMA device tree binding for mxs-dma") Acked-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Markus Pargmann authored
commit f90d3f0d upstream. The property '#pwm-cells' is currently missing. It is not possible to use pwm4 without this property. Signed-off-by:
Markus Pargmann <mpa@pengutronix.de> Fixes: 5658a68f ("ARM i.MX25: Add devicetree") Reviewed-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Philipp Zabel authored
commit 7f8d49dc upstream. The fixed-regulator bindings require a separate property enable-active-high, the standard gpio phandle property polarity setting is ignored. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Fixes: 4fe69a93 ("ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo") Signed-off-by:
-
Stefan Wahren authored
commit 0fdebe1a upstream. The dr_mode of usb0 on imx233-olinuxino is left to default "otg". Since the green LED (GPIO2_1) on imx233-olinuxino is connected to the same pin as USB_OTG_ID it's possible to disable USB host by LED toggling: echo 0 > /sys/class/leds/green/brightness [ 1068.890000] ci_hdrc ci_hdrc.0: remove, state 1 [ 1068.890000] usb usb1: USB disconnect, device number 1 [ 1068.920000] usb 1-1: USB disconnect, device number 2 [ 1068.920000] usb 1-1.1: USB disconnect, device number 3 [ 1069.070000] usb 1-1.2: USB disconnect, device number 4 [ 1069.450000] ci_hdrc ci_hdrc.0: USB bus 1 deregistered [ 1074.460000] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11 This patch fixes the issue by setting dr_mode to "host" in the dts file. Reported-by:
Harald Geyer <harald@ccbib.org> Signed-off-by:
Peter Chen <peter.chen@freescale.com> Fixes: b4931294 ("ARM: dts: imx23-olinuxino: Add USB host support") Signed-off-by:
-
Fabio Estevam authored
commit cfe8c597 upstream. On imx23-olinuxino the LED turns on when level logic high is aplied to GPIO2_1. Fix the gpios property accordingly. Fixes: b34aa185 ("ARM: dts: imx23-olinuxino: Remove unneeded "default-on"") Reported-by:
-
Gregory CLEMENT authored
commit 750e30d4 upstream. There is no crystal connected to the internal RTC on the Open Block AX3. So let's disable it in order to prevent the kernel probing the driver uselessly. Eventually this patches removes the following warning message from the boot log: "rtc-mv d0010300.rtc: internal RTC not ticking" Acked-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Tejun Heo authored
commit 464d1387 upstream. mm/page-writeback.c has several places where 1 is added to the divisor to prevent division by zero exceptions; however, if the original divisor is equivalent to -1, adding 1 leads to division by zero. There are three places where +1 is used for this purpose - one in pos_ratio_polynom() and two in bdi_position_ratio(). The second one in bdi_position_ratio() actually triggered div-by-zero oops on a machine running a 3.10 kernel. The divisor is x_intercept - bdi_setpoint + 1 == span + 1 span is confirmed to be (u32)-1. It isn't clear how it ended up that but it could be from write bandwidth calculation underflow fixed by c72efb65 ("writeback: fix possible underflow in write bandwidth calculation"). At any rate, +1 isn't a proper protection against div-by-zero. This patch converts all +1 protections to |1. Note that bdi_update_dirty_ratelimit() was already using |1 before this patch. Signed-off-by:
Tejun Heo <tj@kernel.org> Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Ming Lei authored
commit 2a34c087 upstream. hctx->tags has to be set as NULL in case that it is to be unmapped no matter if set->tags[hctx->queue_num] is NULL or not in blk_mq_map_swqueue() because shared tags can be freed already from another request queue. The same situation has to be considered during handling CPU online too. Unmapped hw queue can be remapped after CPU topo is changed, so we need to allocate tags for the hw queue in blk_mq_map_swqueue(). Then tags allocation for hw queue can be removed in hctx cpu online notifier, and it is reasonable to do that after mapping is updated. Reported-by:
Dongsu Park <dongsu.park@profitbricks.com> Tested-by:
Ming Lei <ming.lei@canonical.com> Signed-off-by:
-
Ming Lei authored
commit f054b56c upstream. Firstly during CPU hotplug, even queue is freezed, timeout handler still may come and access hctx->tags, which may cause use after free, so this patch deactivates timeout handler inside CPU hotplug notifier. Secondly, tags can be shared by more than one queues, so we have to check if the hctx has been unmapped, otherwise still use-after-free on tags can be triggered. Reported-by:
-
Roy Franz authored
commit 98b228f5 upstream. Until now, the EFI stub was only setting the 32 bit cmd_line_ptr in the setup_header structure, so on 64 bit platforms this could be truncated. This patch adds setting the upper bits of the buffer address in ext_cmd_line_ptr. This case was likely never hit, as the allocation for this buffer is done at the lowest available address. Only x86_64 kernels have this problem, as the 1-1 mapping mandated by EFI ensures that all memory is 32 bit addressable on 32 bit platforms. The EFI stub does not support mixed mode, so the 32 bit kernel on 64 bit firmware case does not need to be handled. Signed-off-by:
Roy Franz <roy.franz@linaro.org> Signed-off-by:
Matt Fleming <matt.fleming@intel.com> Signed-off-by:
-
Ross Lagerwall authored
commit c57dcb56 upstream. Some buggy firmware implementations update VariableNameSize on success such that it does not include the final NUL character which results in garbage in the efivarfs name entries. Use kzalloc on the efivar_entry (as is done in efivars.c) to ensure that the name is always NUL-terminated. The buggy firmware is: BIOS Information Vendor: Intel Corp. Version: S1200RP.86B.02.02.0005.102320140911 Release Date: 10/23/2014 BIOS Revision: 4.6 System Information Manufacturer: Intel Corporation Product Name: S1200RP_SE Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Acked-by:
Matthew Garrett <mjg59@coreos.com> Cc: Jeremy Kerr <jk@ozlabs.org> Signed-off-by:
-
Sam Bobroff authored
commit 0aab3747 upstream. Patches 7cba160a "powernv/cpuidle: Redesign idle states management" and 77b54e9f "powernv/powerpc: Add winkle support for offline cpus" use non-volatile condition registers (cr2, cr3 and cr4) early in the system reset interrupt handler (system_reset_pSeries()) before it has been determined if state loss has occurred. If state loss has not occurred, control returns via the power7_wakeup_noloss() path which does not restore those condition registers, leaving them corrupted. Fix this by restoring the condition registers in the power7_wakeup_noloss() case. This is apparent when running a KVM guest on hardware that does not support winkle or sleep and the guest makes use of secondary threads. In practice this means Power7 machines, though some early unreleased Power8 machines may also be susceptible. The secondary CPUs are taken off line before the guest is started and they call pnv_smp_cpu_kill_self(). This checks support for sleep states (in this case there is no support) and power7_nap() is called. When the CPU is woken, power7_nap() returns and because the CPU is still off line, the main while loop executes again. The sleep states support test is executed again, but because the tested values cannot have changed, the compiler has optimized the test away and instead we rely on the result of the first test, which has been left in cr3 and/or cr4. With the result overwritten, the wrong branch is taken and power7_winkle() is called on a CPU that does not support it, leading to it stalling. Fixes: 7cba160a ("powernv/cpuidle: Redesign idle states management") Fixes: 77b54e9f ("powernv/powerpc: Add winkle support for offline cpus") [mpe: Massage change log a bit more] Signed-off-by:
Sam Bobroff <sam.bobroff@au1.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Nathan Fontenot authored
commit f32393c9 upstream. The incorrect ordering of operations during cpu dlpar add results in invalid affinity for the cpu being added. The ibm,associativity property in the device tree is populated with all zeroes for the added cpu which results in invalid affinity mappings and all cpus appear to belong to node 0. This occurs because rtas configure-connector is called prior to making the rtas set-indicator calls. Phyp does not assign affinity information for a cpu until the rtas set-indicator calls are made to set the isolation and allocation state. Correct the order of operations to make the rtas set-indicator calls (done in dlpar_acquire_drc) before calling rtas configure-connector. Fixes: 1a8061c4 ("powerpc/pseries: Add kernel based CPU DLPAR handling") Signed-off-by:
Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by:
-
Davide Italiano authored
commit 280227a7 upstream. fallocate() checks that the file is extent-based and returns EOPNOTSUPP in case is not. Other tasks can convert from and to indirect and extent so it's safe to check only after grabbing the inode mutex. Signed-off-by:
Davide Italiano <dccitaliano@gmail.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Lukas Czerner authored
commit d2dc317d upstream. Currently it is possible to lose whole file system block worth of data when we hit the specific interaction with unwritten and delayed extents in status extent tree. The problem is that when we insert delayed extent into extent status tree the only way to get rid of it is when we write out delayed buffer. However there is a limitation in the extent status tree implementation so that when inserting unwritten extent should there be even a single delayed block the whole unwritten extent would be marked as delayed. At this point, there is no way to get rid of the delayed extents, because there are no delayed buffers to write out. So when a we write into said unwritten extent we will convert it to written, but it still remains delayed. When we try to write into that block later ext4_da_map_blocks() will set the buffer new and delayed and map it to invalid block which causes the rest of the block to be zeroed loosing already written data. For now we can fix this by simply not allowing to set delayed status on written extent in the extent status tree. Also add WARN_ON() to make sure that we notice if this happens in the future. This problem can be easily reproduced by running the following xfs_io. xfs_io -f -c "pwrite -S 0xaa 4096 2048" \ -c "falloc 0 131072" \ -c "pwrite -S 0xbb 65536 2048" \ -c "fsync" /mnt/test/fff echo 3 > /proc/sys/vm/drop_caches xfs_io -c "pwrite -S 0xdd 67584 2048" /mnt/test/fff This can be theoretically also reproduced by at random by running fsx, but it's not very reliable, though on machines with bigger page size (like ppc) this can be seen more often (especially xfstest generic/127) Signed-off-by:
Lukas Czerner <lczerner@redhat.com> Signed-off-by:
-
Ilya Dryomov authored
commit 082a75da upstream. When we end I/O struct request with error, we need to pass obj_request->length as @nr_bytes so that the entire obj_request worth of bytes is completed. Otherwise block layer ends up confused and we trip on rbd_assert(more ^ (which == img_request->obj_request_count)); in rbd_img_obj_callback() due to more being true no matter what. We already do it in most cases but we are missing some, in particular those where we don't even get a chance to submit any obj_requests, due to an early -ENOMEM for example. A number of obj_request->xferred assignments seem to be redundant but I haven't touched any of obj_request->xferred stuff to keep this small and isolated. Cc: Alex Elder <elder@linaro.org> Reported-by:
Shawn Edwards <lesser.evil@gmail.com> Reviewed-by:
Sage Weil <sage@redhat.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Signed-off-by:
-
- 21 May, 2015 18 commits
-
-
Bard Liao authored
commit 60a8d62b upstream. DMIC clock source is not from codec system clock directly. it is generated from the division of system clock. And it should be 256 * sample rate of AIF1. Signed-off-by:
Bard Liao <bardliao@realtek.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Peter Zubaj authored
commit 7241ea55 upstream. Looks like audigy emu10k2 (probably emu10k1 - sb live too) support two modes for DMA. Second mode is useful for 64 bit os with more then 2 GB of ram (fixes problems with big soundfont loading) 1) 32MB from 2 GB address space using 8192 pages (used now as default) 2) 16MB from 4 GB address space using 4096 pages Mode is set using HCFG_EXPANDED_MEM flag in HCFG register. Also format of emu10k2 page table is then different. Signed-off-by:
Peter Zubaj <pzubaj@marticonet.sk> Tested-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Chris Bainbridge authored
commit 61f8ff69 upstream. Commit 9faf6136 (ACPI / SBS: Disable smart battery manager on Apple) introduced a regression disabling the SBS battery manager. The battery manager should be marked as present when acpi_manager_get_info() returns 0. Fixes: 9faf6136 (ACPI / SBS: Disable smart battery manager on Apple) Signed-off-by:
-
Takashi Iwai authored
commit 1c94e65c upstream. The OSS emulation in synth-emux helper has a potential AB/BA deadlock at the simultaneous closing and opening: close -> snd_seq_release() -> sne_seq_free_client() -> snd_seq_delete_all_ports(): takes client->ports_mutex -> port_delete() -> snd_emux_unuse(): takes emux->register_mutex open -> snd_seq_oss_open() -> snd_emux_open_seq_oss(): takes emux->register_mutex -> snd_seq_event_port_attach() -> snd_seq_create_port(): takes client->ports_mutex This patch addresses the deadlock by reducing the rance taking emux->register_mutex in snd_emux_open_seq_oss(). The lock is needed for the refcount handling, so move it locally. The calls in emux_seq.c are already with the mutex, thus they are replaced with the version without mutex lock/unlock. Signed-off-by:
-
Ludovic Desroches authored
commit a8d4e016 upstream. Maxburst was not set when doing the dma slave configuration. This value is checked by the recently introduced xdmac. It causes an error when doing the slave configuration and so prevents from using dma. Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Michal Simek authored
commit 6befa9d8 upstream. Do not probe all serial drivers by of_serial.c which are using device_type = "serial"; property. Only drivers which have valid compatible strings listed in the driver should be probed. When PORT_UNKNOWN is setup probe will fail anyway. Arnd quotation about driver historical background: "when I wrote that driver initially, the idea was that it would get used as a stub to hook up all other serial drivers but after that, the common code learned to create platform devices from DT" This patch fix the problem with on the system with xilinx_uartps and 16550a where of_serial failed to register for xilinx_uartps and because of irq_dispose_mapping() removed irq_desc. Then when xilinx_uartps was asking for irq with request_irq() EINVAL is returned. Signed-off-by:
Michal Simek <michal.simek@xilinx.com> Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Michal Simek authored
commit 5c90c07b upstream. For systems with CONFIG_SERIAL_OF_PLATFORM=y and device_type = "serial"; property in DT of_serial.c driver maps and unmaps IRQ (because driver probe fails). Then a driver is called but irq mapping is not created that's why driver is failing again in again on request_irq(). Based on this use platform_get_irq() instead of platform_get_resource() which is doing irq_desc allocation and driver itself can request IRQ. Fix both xilinx serial drivers in the tree. Signed-off-by:
-
Quentin Casasnovas authored
commit 0d3bba02 upstream. Phil and I found out a problem with commit: 7e860a6e ("cdc-acm: add sanity checks") It added some sanity checks to ignore potential garbage in CDC headers but also introduced a potential infinite loop. This can happen at the first loop iteration (elength = 0 in that case) if the description isn't a DT_CS_INTERFACE or later if 'buffer[0]' is zero. It should also be noted that the wrong length was being added to 'buffer' in case 'buffer[1]' was not a DT_CS_INTERFACE descriptor, since elength was assigned after that check in the loop. A specially crafted USB device could be used to trigger this infinite loop. Fixes: 7e860a6e ("cdc-acm: add sanity checks") Signed-off-by:
Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by:
Quentin Casasnovas <quentin.casasnovas@oracle.com> CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> CC: Oliver Neukum <oneukum@suse.de> CC: Adam Lee <adam8157@gmail.com> Signed-off-by:
-
Li Jun authored
commit a5a356ce upstream. Wrongly release mutex lock during otg_statemachine may result in re-enter otg_statemachine, which is not allowed, we should do next state transtition after previous one completed. Fixes: 826cfe75 ("usb: chipidea: add OTG fsm operation functions implementation") Signed-off-by:
Li Jun <jun.li@freescale.com> Signed-off-by:
-
Hans de Goede authored
commit 8e779c6c upstream. Testing has shown that ASM1053 devices do not work properly with transfers larger than 240 sectors, so set max_sectors to 240 on these. Reported-by:
Steve Bangert <sbangert@frontier.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Tested-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Hans de Goede authored
commit ee136af4 upstream. The usb-storage driver sets max_sectors = 240 in its scsi-host template, for uas we do not want to do that for all devices, but testing has shown that some devices need it. This commit adds a US_FL_MAX_SECTORS_240 flag for such devices, and implements support for it in uas.c, while at it it also adds support for US_FL_MAX_SECTORS_64 to uas.c. Signed-off-by:
-
Hans de Goede authored
commit a5011d44 upstream. uas_use_uas_driver may set some US_FL_foo flags during detection, currently these are stored in a local variable and then throw away, but these may be of interest to the caller, so add an extra parameter to (optionally) return the detected flags, and use this in the uas driver. Signed-off-by:
-
Christoph Hellwig authored
commit 118c855b upstream. The 3w-9xxx driver needs to tear down the dma mappings before returning the command to the midlayer, as there is no guarantee the sglist and count are valid after that point. Also remove the dma mapping helpers which have another inherent race due to the request_id index. Signed-off-by:
Christoph Hellwig <hch@lst.de> Acked-by:
Adam Radford <aradford@gmail.com> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Christoph Hellwig authored
commit 9cd95546 upstream. The 3w-xxxx driver needs to tear down the dma mappings before returning the command to the midlayer, as there is no guarantee the sglist and count are valid after that point. Also remove the dma mapping helpers which have another inherent race due to the request_id index. Signed-off-by:
-
Christoph Hellwig authored
commit 579d69bc upstream. The 3w-sas driver needs to tear down the dma mappings before returning the command to the midlayer, as there is no guarantee the sglist and count are valid after that point. Also remove the dma mapping helpers which have another inherent race due to the request_id index. Signed-off-by:
Torsten Luettgert <ml-lkml@enda.eu> Tested-by:
Bernd Kardatzki <Bernd.Kardatzki@med.uni-tuebingen.de> Acked-by:
-
Mike Christie authored
commit 35e9a9f9 upstream. This works around a issue with qnap iscsi targets not handling large IOs very well. The target returns: VPD INQUIRY: Block limits page (SBC) Maximum compare and write length: 1 blocks Optimal transfer length granularity: 1 blocks Maximum transfer length: 4294967295 blocks Optimal transfer length: 4294967295 blocks Maximum prefetch, xdread, xdwrite transfer length: 0 blocks Maximum unmap LBA count: 8388607 Maximum unmap block descriptor count: 1 Optimal unmap granularity: 16383 Unmap granularity alignment valid: 0 Unmap granularity alignment: 0 Maximum write same length: 0xffffffff blocks Maximum atomic transfer length: 0 Atomic alignment: 0 Atomic transfer length granularity: 0 and it is *sometimes* able to handle at least one IO of size up to 8 MB. We have seen in traces where it will sometimes work, but other times it looks like it fails and it looks like it returns failures if we send multiple large IOs sometimes. Also it looks like it can return 2 different errors. It will sometimes send iscsi reject errors indicating out of resources or it will send invalid cdb illegal requests check conditions. And then when it sends iscsi rejects it does not seem to handle retries when there are command sequence holes, so I could not just add code to try and gracefully handle that error code. The problem is that we do not have a good contact for the company, so we are not able to determine under what conditions it returns which error and why it sometimes works. So, this patch just adds a new black list flag to set targets like this to the old max safe sectors of 1024. The max_hw_sectors changes added in 3.19 caused this regression, so I also ccing stable. Reported-by:
Christian Hesse <list@eworm.de> Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Reviewed-by:
-
Christian König authored
commit c29c0876 upstream. Otherwise the change isn't atomic. Signed-off-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Christian König authored
commit 48afbd70 upstream. Otherwise it is possible that we will have page table corruption if we change a BOs address multiple times. Signed-off-by:
-
