Move a few things around in "ipa_reg.h":
  - Move the definition of ipa_reg_state_aggr_active_offset() down
    a bit in the file so definitions are ordered by offset (for
    the lowest supported IPA version) like all other definitions.
  - Move the definition TIMER_FREQUENCY to be immediately above
    the definition of ipa_aggr_granularity_val() where it's used.
  - Move each register field value enumerated type definition to
    immediately follow the definitions of the register and field
    it is associated with.
No code functionality is modified by this patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Revise or add comments in "ipa_reg.h" for to provide more
information, and to improve clarity and consistency.
  - Always provide a comment to define when a register or field is
    supported (or not) for certain versions of IPA hardware.
  - Try to be specific about *which* or *how many* definitions
    a comment refers to.
  - Move comments stating that ipa->available defines the valid
    bits in various registers *above* the register offset
    definition, to avoid some checkpatch.pl warnings.
No code is changed by this patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Consistently define numeric values for enumerated type members using
hexidecimal (rather than decimal) format values.  Align the values
assigned in the same column in each file.

Only assign values where they really matter, for example don't
assign IPA_ENDPOINT_AP_MODEM_TX the value 0.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The backward compatibility register field masks are defined using
single-bit masks defined with BIT(x) rather than GENMASK(x, x).
Change this one set of definitions to follow the GENMASK() pattern
used everywhere else.  Add a few missing field definitions for this
register as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Several IPA register field masks are defined without the "_FMASK"
suffix naming convention.  Rename these, so all field masks are
consistently named.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Rename two suspend IRQ registers so they follow the IPA_REG_IRQ_xxx
naming convention used elsewhere.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

IPA version 3.5.1 represents the timer used in avoiding head-of-line
blocking with a simple tick count.  IPA v4.2 changes that, instead
splitting the timer field into two parts (base and scale) to
represent the ticks in the timer period.

IPA v4.0 and IPA v4.1 use the same method as IPA v3.5.1.  Change the
test in ipa_reg_init_hol_block_timer_val() so the result is correct
for those versions as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

For IPA v3.5.1, the IPA filter/routing hash enable register actually
does exist, but it is at offset 0x8c into the IPA register space.
For newer versions of IPA it is at offset 0x148.

Define a new inline function ipa_reg_filt_rout_hash_en_offset() to
return the appropriate value for a given version of IPA hardware.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The IPA filter/routing hash enable register and filter/routing hash
flush register each have four single-bit fields representing the
four hashed tables to be enabled or flushed.  The field positions
are identical, so just use a single set of field masks to represent
the fields for both registers.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

commit f7365919 ("net: wan: Delete the DLCI / SDLA drivers")
deleted "Documentation/networking/framerelay.rst". However, it is still
referenced in "Documentation/networking/index.rst". We need to remove the
reference, too.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201118124226.15588-1-xie.he.0141@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Ido Schimmel says:

====================
mlxsw: Preparations for nexthop objects support - part 2/2

This patch set contains the second round of preparations towards nexthop
objects support in mlxsw. Follow up patches can be found here [1].

The patches are mostly small and trivial and contain non-functional
changes aimed at making it easier to integrate nexthop objects with
mlxsw.

Patch #1 is a fix for an issue introduced in previous submission. Found
by Coverity.

[1] https://github.com/idosch/linux/tree/submit/nexthop_objects
====================

Link: https://lore.kernel.org/r/20201117174704.291990-1-idosch@idosch.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The function is responsible for allocating the adjacency entries used by
the nexthop group and populating them with the adjacency information
such as egress RIF and MAC address.

Allow the function to return an error when it encounters a problem and
have the relevant call sites check it.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, a nexthop group is destroyed when the last FIB entry is
detached from it.

When nexthop objects are supported, this can no longer be the case, as
the group is a separate object whose lifetime is managed by user space.

Add an indication if a nexthop group can be destroyed and always set it
to true for the existing IPv4 and IPv6 nexthop groups.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When the IPv6 FIB info has a nexthop object, the nexthop offload
indication is set on the nexthop object and not on the FIB info itself.

Therefore, do not try to clear the offload indication from the FIB info
when it has a nexthop object.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Attach the FIB entry to the nexthop group after setting the offload flag
on the IPv6 FIB info (i.e., 'struct fib6_info'). The second operation is
not needed when the nexthop group is a nexthop object. This will allow
us to have a common exit path from the function, regardless of the
nexthop group's type.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The previous patch associated a nexthop group with the FIB entry before
the entry's type is determined.

Make use of the nexthop group when determining the entry's type instead
of relying on helpers that assume that the nexthop info is not a nexthop
object (i.e., 'struct nexthop').
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Each FIB entry has a type (e.g., remote, local) that determines how the
entry is programmed to the device. In order to determine if the entry is
local (directly connected) or remote (has a gateway) the relevant FIB
info structures (e.g., 'struct fib_info') are checked.

When entries that use nexthop objects are supported, these checks will
need to be changed to take into account 'struct nexthop'.

Instead, first associate the entry with a nexthop group so that the next
patch could determine the entry's type based on the associated nexthop
group's type.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The sole caller of the function will soon only have the ifindex
available, instead of the pointer itself.

Therefore, change the function to take the ifindex as input and have it
get the pointer.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The ifindex of the nexthop device was never set for IPv4 nexthops,
unlike IPv6 nexthops. This went unnoticed since only IPv6 nexthops use
it.

Set the ifindex for IPv4 nexthops in order to be consistent with IPv6
and also because it will be used by a later patch.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The function allocates 'nhgi', not 'nh_grp', so it needs to free the
former in its error path.

Fixes: 7f7a417e ("mlxsw: spectrum_router: Split nexthop group configuration to a different struct")
Addresses-Coverity: ("Memory - corruptions  (USE_AFTER_FREE)")
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It's arguable most people interested in configuring a PPS signal
want it as external output, not as kernel input. PTP_CLK_REQ_PPS
is for input though. Add documentation to nudge readers into
the correct direction.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201117213826.18235-1-a.fatoum@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix the following unreachable code issue:

   drivers/net/ethernet/netronome/nfp/crypto/tls.c: In function 'nfp_net_tls_add':
   include/linux/compiler_attributes.h:208:41: warning: statement will never be executed [-Wswitch-unreachable]
     208 | # define fallthrough                    __attribute__((__fallthrough__))
         |                                         ^~~~~~~~~~~~~
   drivers/net/ethernet/netronome/nfp/crypto/tls.c:299:3: note: in expansion of macro 'fallthrough'
     299 |   fallthrough;
         |   ^~~~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Link: https://lore.kernel.org/r/20201117171347.GA27231@embeddedorSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Mauro Carvalho Chehab says:

====================
Fix several bad kernel-doc markups

Kernel-doc has always be limited to a probably bad documented
rule:

The kernel-doc markups should appear *imediatelly before* the
function or data structure that it documents.

On other words, if a C file would contain something like this:

	/**
	 * foo - function foo
	 * @args: foo args
	 */
	static inline void bar(int args);

	/**
	 * bar - function bar
	 * @args: foo args
	 */
	static inline void foo(void *args);

The output (in ReST format) will be:

	.. c:function:: void bar (int args)

	   function foo

	**Parameters**

	``int args``
	  foo args

	.. c:function:: void foo (void *args)

	   function bar

	**Parameters**

	``void *args``
	  foo args

Which is clearly a wrong result.  Before this changeset,
not even a warning is produced on such cases.

As placing such markups just before the documented
data is a common practice, on most cases this is fine.

However, as patches touch things, identifiers may be
renamed, and people may forget to update the kernel-doc
markups to follow such changes.

This has been happening for quite a while, as there are
lots of files with kernel-doc problems.

This series address those issues and add a file at the
end that will enforce that the identifier will match the
kernel-doc markup, avoiding this problem from
keep happening as time goes by.
====================

Link: https://lore.kernel.org/r/cover.1605521731.git.mchehab+huawei@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Some identifiers have different names between their prototypes
and the kernel-doc markup.

In the specific case of netif_subqueue_stopped(), keep the
current markup for __netif_subqueue_stopped(), adding a
new one for netif_subqueue_stopped().
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some identifiers have different names between their prototypes
and the kernel-doc markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some functions have different names between their prototypes
and the kernel-doc markup.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Naveen Mamindlapalli says:

====================
Add ethtool ntuple filters support

This patch series adds support for ethtool ntuple filters, unicast
address filtering, VLAN offload and SR-IOV ndo handlers. All of the
above features are based on the Admin Function(AF) driver support to
install and delete the low level MCAM entries. Each MCAM entry is
programmed with the packet fields to match and what actions to take
if the match succeeds. The PF driver requests AF driver to allocate
set of MCAM entries to be used to install the flows by that PF. The
entries will be freed when the PF driver is unloaded.

* The patches 1 to 4 adds AF driver infrastructure to install and
  delete the low level MCAM flow entries.
* Patch 5 adds ethtool ntuple filter support.
* Patch 6 adds unicast MAC address filtering.
* Patch 7 adds support for dumping the MCAM entries via debugfs.
* Patches 8 to 10 adds support for VLAN offload.
* Patch 10 to 11 adds support for SR-IOV ndo handlers.
* Patch 12 adds support to read the MCAM entries.

Misc:
* Removed redundant mailbox NIX_RXVLAN_ALLOC.
====================

Link: https://lore.kernel.org/r/20201114195303.25967-1-naveenm@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since mailbox message for installing flows is in place,
remove the RXVLAN_ALLOC mbox message which is redundant.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch introduces new mailbox mesages to retrieve a given
MCAM entry or base flow steering rule of a VF installed by its
parent PF. This helps while updating the existing MCAM rules
with out re-framing the whole mailbox request again. The INSTALL
FLOW mailbox consumer can read-modify-write the existing entry.
Similarly while installing new flow rules for a VF, the base
flow steering rule match creteria is copied to the new flow rule
and the deltas are appended to the new rule.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Co-developed-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch handles the VF mac address changes as given below.
    1. mac addr configrued by VF will be retained until VF module unload.
    2. mac addr configred by PF for VF will be retained until power cycle.
    3. mac addr confgired by PF for its VF can't be overwritten by VF.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch adds support for ndo_set_vf_mac, ndo_set_vf_vlan
and ndo_get_vf_config handlers. The traffic redirection
based on the VF mac address or vlan id is done by installing
MCAM rules. Reserved RX_VTAG_TYPE7 in each NIXLF for VF VLAN
which strips the VLAN tag from ingress VLAN traffic. The NIX PF
allocates two MCAM entries for VF VLAN feature, one used for
ingress VTAG strip and another entry for egress VTAG insertion.

This patch also updates the MAC address in PF installed VF VLAN
rule upon receiving nix_lf_start_rx mbox request for VF since
Administrative Function driver will assign a valid MAC addr
in nix_lf_start_rx function.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Co-developed-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch implements egress VLAN offload by appending NIX_SEND_EXT_S
header to NIX_SEND_HDR_S. The VLAN TCI information is specified
in the NIX_SEND_EXT_S. The VLAN offload in the ingress path is
implemented by configuring the NIX_RX_VTAG_ACTION_S to strip and
capture the outer vlan fields. The NIX PF allocates one MCAM entry
for Rx VLAN offload.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch modifies the existing nix_vtag_config mailbox message
to allocate and free TX VTAG entries as requested by a NIX PF.
The TX VTAG entries are global resource that shared by all PFs
and each entry specifies the size of VTAG to insert and the VTAG
header data to insert. The mailbox response contains the entry
index which is used by mailbox requester in configuring the
NPC_TX_VTAG_ACTION for any MCAM entry.
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add debugfs support to dump the MCAM rules installed using
NPC_INSTALL_FLOW mbox message. Debugfs file can display mcam
entry, counter if any, flow type and counter hits.

Ethtool will dump the ntuple flows related to the PF only.
The debugfs file gives systemwide view of the MCAM rules
installed by all the PF's.

Below is the example output when the debugfs file is read:
~ # mount -t debugfs none /sys/kernel/debug
~ # cat /sys/kernel/debug/octeontx2/npc/mcam_rules

	Installed by: PF1
	direction: RX
        mcam entry: 227
	udp source port 23 mask 0xffff
	Forward to: PF1 VF0
        action: Direct to queue 0
	enabled: yes
        counter: 1
        hits: 0
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add unicast MAC address filtering support using install flow
message. Total of 8 MCAM entries are allocated for adding
unicast mac filtering rules. If the MCAM allocation fails,
the unicast filtering support will not be advertised.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch adds support for adding and deleting ethtool ntuple
filters. The filters for ether, ipv4, ipv6, tcp, udp and sctp
are supported. The mask is also supported. The supported actions
are drop and direct to a queue. Additionally we support FLOW_EXT
field vlan_tci and FLOW_MAC_EXT.

The NIX PF will allocate total 32 MCAM entries for the use of
ethtool ntuple filters. The Administrative Function(AF) will
install/delete the MCAM rules when NIX PF sends mailbox message
to install/delete the ntuple filters.

Ethtool ntuple filters support is restricted to PFs as of now
and PF can install ntuple filters to direct the traffic to its
VFs. Hence added a separate callback for VFs to get/set RSS
configuration.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Added new mailbox messages to install and delete MCAM rules.
These mailbox messages will be used for adding/deleting ethtool
n-tuple filters by NIX PF. The installed MCAM rules are stored
in a list that will be traversed later to delete the MCAM entries
when the interface is brought down or when PCIe FLR is received.
The delete mailbox supports deleting a single MCAM entry or range
of entries or all the MCAM entries owned by the pcifunc. Each MCAM
entry can be associated with a HW match stat entry if the mailbox
requester wants to check the hit count for debugging.

Modified adding default unicast DMAC match rule using install
flow API. The default unicast DMAC match entry installed by
Administrative Function is saved and can be changed later by the
mailbox user to fit additional fields, or the default MCAM entry
rule action can be used for other flow rules installed later.

Modified rvu_mbox_handler_nix_lf_free mailbox to add a flag to
disable or delete the MCAM entries. The MCAM entries are disabled
when the interface is brought down and deleted in FLR handler.
The disabled MCAM entries will be re-enabled when the interface
is brought up again.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Key Extraction(KEX) profile decides how the packet metadata such as
layer information and selected packet data bytes at each layer are
placed in MCAM search key. This patch reads the configured KEX profile
parameters to find out the bit position and bit mask for each field.
The information is used when programming the MCAM match data by SW
to match a packet flow and take appropriate action on the flow. This
patch also verifies the mandatory fields such as channel and DMAC
are not overwritten by the KEX configuration of other fields.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch adds support to verify the channel number sent by
mailbox requester before writing MCAM entry for Ingress packets.
Similarly for Egress packets, verifying the PF_FUNC sent by the
mailbox user.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The current default Key Extraction(KEX) profile can only use RX
packet fields while generating the MCAM search key. The profile
can't be used for matching TX packet fields. This patch modifies
the default KEX profile to add support for extracting TX packet
fields into MCAM search key. Enabled Tx KPU packet parsing by
configuring TX PKIND in tx_parse_cfg.

Modified the KEX profile to extract 2 bytes of VLAN TCI from an
offset of 2 bytes from LB_PTR. The LB_PTR points to the byte offset
where the VLAN header starts. The NPC KPU parser profile has been
modified to point LB_PTR to the starting byte offset of VLAN header
which points to the tpid field.
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>