- 07 Jan, 2020 40 commits
-
-
Jiangfeng Xiao authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 90b3b339 ] When doing stress test, we get the following trace: kernel BUG at lib/dynamic_queue_limits.c:26! Internal error: Oops - BUG: 0 [#1] SMP ARM Modules linked in: hip04_eth CPU: 0 PID: 2003 Comm: tDblStackPcap0 Tainted: G O L 4.4.197 #1 Hardware name: Hisilicon A15 task: c3637668 task.stack: de3bc000 PC is at dql_completed+0x18/0x154 LR is at hip04_tx_reclaim+0x110/0x174 [hip04_eth] pc : [<c041abfc>] lr : [<bf0003a8>] psr: 800f0313 sp : de3bdc2c ip : 00000000 fp : c020fb10 r10: 00000000 r9 : c39b4224 r8 : 00000001 r7 : 00000046 r6 : c39b4000 r5 : 0078f392 r4 : 0078f392 r3 : 00000047 r2 : 00000000 r1 : 00000046 r0 : df5d5c80 Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 32c5387d Table: 1e189b80 DAC: 55555555 Process tDblStackPcap0 (pid: 2003, stack limit = 0xde3bc190) Stack: (0xde3bdc2c to 0xde3be000) [<c041abfc>] (dql_completed) from [<bf0003a8>] (hip04_tx_reclaim+0x110/0x174 [hip04_eth]) [<bf0003a8>] (hip04_tx_reclaim [hip04_eth]) from [<bf0012c0>] (hip04_rx_poll+0x20/0x388 [hip04_eth]) [<bf0012c0>] (hip04_rx_poll [hip04_eth]) from [<c04c8d9c>] (net_rx_action+0x120/0x374) [<c04c8d9c>] (net_rx_action) from [<c021eaf4>] (__do_softirq+0x218/0x318) [<c021eaf4>] (__do_softirq) from [<c021eea0>] (irq_exit+0x88/0xac) [<c021eea0>] (irq_exit) from [<c0240130>] (msa_irq_exit+0x11c/0x1d4) [<c0240130>] (msa_irq_exit) from [<c0267ba8>] (__handle_domain_irq+0x110/0x148) [<c0267ba8>] (__handle_domain_irq) from [<c0201588>] (gic_handle_irq+0xd4/0x118) [<c0201588>] (gic_handle_irq) from [<c0558360>] (__irq_svc+0x40/0x58) Exception stack(0xde3bdde0 to 0xde3bde28) dde0: 00000000 00008001 c3637668 00000000 00000000 a00f0213 dd3627a0 c0af6380 de00: c086d380 a00f0213 c0a22a50 de3bde6c 00000002 de3bde30 c0558138 c055813c de20: 600f0213 ffffffff [<c0558360>] (__irq_svc) from [<c055813c>] (_raw_spin_unlock_irqrestore+0x44/0x54) Kernel panic - not syncing: Fatal exception in interrupt Pre-modification code: int hip04_mac_start_xmit(struct sk_buff *skb, struct net_device *ndev) { [...] [1] priv->tx_head = TX_NEXT(tx_head); [2] count++; [3] netdev_sent_queue(ndev, skb->len); [...] } An rx interrupt occurs if hip04_mac_start_xmit just executes to the line 2, tx_head has been updated, but corresponding 'skb->len' has not been added to dql_queue. And then hip04_mac_interrupt->__napi_schedule->hip04_rx_poll->hip04_tx_reclaim In hip04_tx_reclaim, because tx_head has been updated, bytes_compl will plus an additional "skb-> len" which has not been added to dql_queue. And then trigger the BUG_ON(bytes_compl > num_queued - dql->num_completed). To solve the problem described above, we put "netdev_sent_queue(ndev, skb->len);" before "priv->tx_head = TX_NEXT(tx_head);" Fixes: a41ea46a ("net: hisilicon: new hip04 ethernet driver") Signed-off-by:
Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by:
Kleber Sacilotto de Souza <kleber.souza@canonical.com>
-
Russell King authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit d2ed49cf ] When a PHY is probed, if the top bit is set, we end up requesting a module with the string "mdio:-10101110000000100101000101010001" - the top bit is printed to a signed -1 value. This leads to the module not being loaded. Fix the module format string and the macro generating the values for it to ensure that we only print unsigned types and the top bit is always 0/1. We correctly end up with "mdio:10101110000000100101000101010001". Fixes: 8626d3b4 ("phylib: Support phy module autoloading") Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Chuhong Yuan authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit a288f105 ] fjes_acpi_add() misses a check for platform_device_register_simple(). Add a check to fix it. Fixes: 658d439b ("fjes: Introduce FUJITSU Extended Socket Network Device driver") Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Signed-off-by:
-
Mao Wenan authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit b43d1f9f ] There is softlockup when using TPACKET_V3: ... NMI watchdog: BUG: soft lockup - CPU#2 stuck for 60010ms! (__irq_svc) from [<c0558a0c>] (_raw_spin_unlock_irqrestore+0x44/0x54) (_raw_spin_unlock_irqrestore) from [<c027b7e8>] (mod_timer+0x210/0x25c) (mod_timer) from [<c0549c30>] (prb_retire_rx_blk_timer_expired+0x68/0x11c) (prb_retire_rx_blk_timer_expired) from [<c027a7ac>] (call_timer_fn+0x90/0x17c) (call_timer_fn) from [<c027ab6c>] (run_timer_softirq+0x2d4/0x2fc) (run_timer_softirq) from [<c021eaf4>] (__do_softirq+0x218/0x318) (__do_softirq) from [<c021eea0>] (irq_exit+0x88/0xac) (irq_exit) from [<c0240130>] (msa_irq_exit+0x11c/0x1d4) (msa_irq_exit) from [<c0209cf0>] (handle_IPI+0x650/0x7f4) (handle_IPI) from [<c02015bc>] (gic_handle_irq+0x108/0x118) (gic_handle_irq) from [<c0558ee4>] (__irq_usr+0x44/0x5c) ... If __ethtool_get_link_ksettings() is failed in prb_calc_retire_blk_tmo(), msec and tmo will be zero, so tov_in_jiffies is zero and the timer expire for retire_blk_timer is turn to mod_timer(&pkc->retire_blk_timer, jiffies + 0), which will trigger cpu usage of softirq is 100%. Fixes: f6fb8f10 ("af-packet: TPACKET_V3 flexible buffer implementation.") Tested-by:
Mao Wenan <maowenan@huawei.com> Signed-off-by:
-
Takashi Iwai authored
BugLink: https://bugs.launchpad.net/bugs/1858462 commit add9d56d upstream. The current PCM code doesn't initialize explicitly the buffers allocated for PCM streams, hence it might leak some uninitialized kernel data or previous stream contents by mmapping or reading the buffer before actually starting the stream. Since this is a common problem, this patch simply adds the clearance of the buffer data at hw_params callback. Although this does only zero-clear no matter which format is used, which doesn't mean the silence for some formats, but it should be OK because the intention is just to clear the previous data on the buffer. Reported-by:
Lionel Koenig <lionel.koenig@gmail.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191211155742.3213-1-tiwai@suse.deSigned-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Filipe Manana authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 6609fee8 ] When a tree mod log user no longer needs to use the tree it calls btrfs_put_tree_mod_seq() to remove itself from the list of users and delete all no longer used elements of the tree's red black tree, which should be all elements with a sequence number less then our equals to the caller's sequence number. However the logic is broken because it can delete and free elements from the red black tree that have a sequence number greater then the caller's sequence number: 1) At a point in time we have sequence numbers 1, 2, 3 and 4 in the tree mod log; 2) The task which got assigned the sequence number 1 calls btrfs_put_tree_mod_seq(); 3) Sequence number 1 is deleted from the list of sequence numbers; 4) The current minimum sequence number is computed to be the sequence number 2; 5) A task using sequence number 2 is at tree_mod_log_rewind() and gets a pointer to one of its elements from the red black tree through a call to tree_mod_log_search(); 6) The task with sequence number 1 iterates the red black tree of tree modification elements and deletes (and frees) all elements with a sequence number less then or equals to 2 (the computed minimum sequence number) - it ends up only leaving elements with sequence numbers of 3 and 4; 7) The task with sequence number 2 now uses the pointer to its element, already freed by the other task, at __tree_mod_log_rewind(), resulting in a use-after-free issue. When CONFIG_DEBUG_PAGEALLOC=y it produces a trace like the following: [16804.546854] general protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC PTI [16804.547451] CPU: 0 PID: 28257 Comm: pool Tainted: G W 5.4.0-rc8-btrfs-next-51 #1 [16804.548059] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c8995f-prebuilt.qemu.org 04/01/2014 [16804.548666] RIP: 0010:rb_next+0x16/0x50 (...) [16804.550581] RSP: 0018:ffffb948418ef9b0 EFLAGS: 00010202 [16804.551227] RAX: 6b6b6b6b6b6b6b6b RBX: ffff90e0247f6600 RCX: 6b6b6b6b6b6b6b6b [16804.551873] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff90e0247f6600 [16804.552504] RBP: ffff90dffe0d4688 R08: 0000000000000001 R09: 0000000000000000 [16804.553136] R10: ffff90dffa4a0040 R11: 0000000000000000 R12: 000000000000002e [16804.553768] R13: ffff90e0247f6600 R14: 0000000000001663 R15: ffff90dff77862b8 [16804.554399] FS: 00007f4b197ae700(0000) GS:ffff90e036a00000(0000) knlGS:0000000000000000 [16804.555039] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [16804.555683] CR2: 00007f4b10022000 CR3: 00000002060e2004 CR4: 00000000003606f0 [16804.556336] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [16804.556968] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [16804.557583] Call Trace: [16804.558207] __tree_mod_log_rewind+0xbf/0x280 [btrfs] [16804.558835] btrfs_search_old_slot+0x105/0xd00 [btrfs] [16804.559468] resolve_indirect_refs+0x1eb/0xc70 [btrfs] [16804.560087] ? free_extent_buffer.part.19+0x5a/0xc0 [btrfs] [16804.560700] find_parent_nodes+0x388/0x1120 [btrfs] [16804.561310] btrfs_check_shared+0x115/0x1c0 [btrfs] [16804.561916] ? extent_fiemap+0x59d/0x6d0 [btrfs] [16804.562518] extent_fiemap+0x59d/0x6d0 [btrfs] [16804.563112] ? __might_fault+0x11/0x90 [16804.563706] do_vfs_ioctl+0x45a/0x700 [16804.564299] ksys_ioctl+0x70/0x80 [16804.564885] ? trace_hardirqs_off_thunk+0x1a/0x20 [16804.565461] __x64_sys_ioctl+0x16/0x20 [16804.566020] do_syscall_64+0x5c/0x250 [16804.566580] entry_SYSCALL_64_after_hwframe+0x49/0xbe [16804.567153] RIP: 0033:0x7f4b1ba2add7 (...) [16804.568907] RSP: 002b:00007f4b197adc88 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [16804.569513] RAX: ffffffffffffffda RBX: 00007f4b100210d8 RCX: 00007f4b1ba2add7 [16804.570133] RDX: 00007f4b100210d8 RSI: 00000000c020660b RDI: 0000000000000003 [16804.570726] RBP: 000055de05a6cfe0 R08: 0000000000000000 R09: 00007f4b197add44 [16804.571314] R10: 0000000000000000 R11: 0000000000000246 R12: 00007f4b197add48 [16804.571905] R13: 00007f4b197add40 R14: 00007f4b100210d0 R15: 00007f4b197add50 (...) [16804.575623] ---[ end trace 87317359aad4ba50 ]--- Fix this by making btrfs_put_tree_mod_seq() skip deletion of elements that have a sequence number equals to the computed minimum sequence number, and not just elements with a sequence number greater then that minimum. Fixes: bd989ba3 ("Btrfs: add tree modification log functions") CC: stable@vger.kernel.org # 4.4+ Reviewed-by:
Josef Bacik <josef@toxicpanda.com> Signed-off-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
Sasha Levin <sashal@kernel.org> Signed-off-by:
-
Josef Bacik authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit c7e54b51 ] We can just abort the transaction here, and in fact do that for every other failure in this function except these two cases. CC: stable@vger.kernel.org # 4.4+ Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
-
Dan Carpenter authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit b6293c82 ] Callers of alloc_test_extent_buffer have not correctly interpreted the return value as error pointer, as alloc_test_extent_buffer should behave as alloc_extent_buffer. The self-tests were unaffected but btrfs_find_create_tree_block could call both functions and that would cause problems up in the call chain. Fixes: faa2dbf0 ("Btrfs: add sanity tests for new qgroup accounting code") CC: stable@vger.kernel.org # 4.4+ Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
-
Josef Bacik authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit f72ff01d ] Testing with the new fsstress uncovered a pretty nasty deadlock with lookup and snapshot deletion. Process A unlink -> final iput -> inode_tree_del -> synchronize_srcu(subvol_srcu) Process B btrfs_lookup <- srcu_read_lock() acquired here -> btrfs_iget -> find inode that has I_FREEING set -> __wait_on_freeing_inode() We're holding the srcu_read_lock() while doing the iget in order to make sure our fs root doesn't go away, and then we are waiting for the inode to finish freeing. However because the free'ing process is doing a synchronize_srcu() we deadlock. Fix this by dropping the synchronize_srcu() in inode_tree_del(). We don't need people to stop accessing the fs root at this point, we're only adding our empty root to the dead roots list. A larger much more invasive fix is forthcoming to address how we deal with fs roots, but this fixes the immediate problem. Fixes: 76dda93c ("Btrfs: add snapshot/subvolume destroy ioctl") CC: stable@vger.kernel.org # 4.4+ Signed-off-by:
-
Guenter Roeck authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 6056a0f8 ] The following build warning is seen if CONFIG_PM is disabled. drivers/usb/host/xhci-pci.c:498:13: warning: unused function 'xhci_pci_shutdown' Fixes: f2c710f7 ("usb: xhci: only set D3hot for pci device") Cc: Henry Lin <henryl@nvidia.com> Cc: stable@vger.kernel.org # all stable releases with f2c710f7Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Acked-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20191218011911.6907-1-linux@roeck-us.netSigned-off-by:
-
Faiz Abbas authored
BugLink: https://bugs.launchpad.net/bugs/1858462 commit 07bcc411 upstream. This reverts commit c894e33d. This commit aims to treat SD High speed and SDR25 as the same while setting UHS Timings in HOST_CONTROL2 which leads to failures with some SD cards in AM65x. Revert this commit. The issue this commit was trying to fix can be implemented in a platform specific callback instead of common sdhci code. Cc: <stable@vger.kernel.org> Signed-off-by:
Faiz Abbas <faiz_abbas@ti.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.comSigned-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Russell King authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit a5d66f81 ] When a phydev is created, the speed and duplex are set to zero and -1 respectively, rather than using the predefined SPEED_UNKNOWN and DUPLEX_UNKNOWN constants. There is a window at initialisation time where we may report link down using the 0/-1 values. Tidy this up and use the predefined constants, so debug doesn't complain with: "Unsupported (update phy-core.c)/Unsupported (update phy-core.c)" when the speed and duplex settings are printed. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
-
Hewenliang authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 10992af6 ] It is necessary to free the memory that we have allocated when error occurs. Fixes: ef3072cd ("tools lib traceevent: Get rid of die in add_filter_type()") Signed-off-by:
Hewenliang <hewenliang4@huawei.com> Reviewed-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Tzvetomir Stoyanov <tstoyanov@vmware.com> Link: http://lore.kernel.org/lkml/20191119014415.57210-1-hewenliang4@huawei.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Michael Ellerman authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 4ee812f6 ] In the vmx crypto Makefile we assign to a variable called TARGET and pass that to the aesp8-ppc.pl and ghashp8-ppc.pl scripts. The variable is meant to describe what flavour of powerpc we're building for, eg. either 32 or 64-bit, and big or little endian. Unfortunately TARGET is a fairly common name for a make variable, and if it happens that TARGET is specified as a command line parameter to make, the value specified on the command line will override our value. In particular this can happen if the kernel Makefile is driven by an external Makefile that uses TARGET for something. This leads to weird build failures, eg: nonsense at /build/linux/drivers/crypto/vmx/ghashp8-ppc.pl line 45. /linux/drivers/crypto/vmx/Makefile:20: recipe for target 'drivers/crypto/vmx/ghashp8-ppc.S' failed Which shows that we passed an empty value for $(TARGET) to the perl script, confirmed with make V=1: perl /linux/drivers/crypto/vmx/ghashp8-ppc.pl > drivers/crypto/vmx/ghashp8-ppc.S We can avoid this confusion by using override, to tell make that we don't want anything to override our variable, even a value specified on the command line. We can also use a less common name, given the script calls it "flavour", let's use that. Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Corentin Labbe authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit a7126603 ] If you try to compile this driver on a 64-bit platform then you will get warnings because it mixes size_t with unsigned int which only works on 32-bit. This patch fixes all of the warnings on sun4i-ss-hash.c. Signed-off-by:
Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by:
-
Andy Shevchenko authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 21f58548 ] New GCC warns about inappropriate use of strncpy(): drivers/staging/fbtft/fbtft-core.c: In function ‘fbtft_framebuffer_alloc’: drivers/staging/fbtft/fbtft-core.c:665:2: warning: ‘strncpy’ specified bound 16 equals destination size [-Wstringop-truncation] 665 | strncpy(info->fix.id, dev->driver->name, 16); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Later on the copy is being used with the assumption to be NULL terminated. Make sure string is NULL terminated by switching to snprintf(). Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20191120095716.26628-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Johannes Berg authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 5974fbb5 ] kasprintf() can fail, we should check the return value. Fixes: 5ed540ae ("iwlwifi: use mac80211 throughput trigger") Fixes: 8ca151b5 ("iwlwifi: add the MVM driver") Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
-
Omar Sandoval authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 9be490f1 ] Currently, end_workqueue_fn() frees the end_io_wq entry (which embeds the work item) and then calls bio_endio(). This is another potential instance of the bug in "btrfs: don't prematurely free work in run_ordered_work()". In particular, the endio call may depend on other work items. For example, btrfs_end_dio_bio() can call btrfs_subio_endio_read() -> __btrfs_correct_data_nocsum() -> dio_read_error() -> submit_dio_repair_bio(), which submits a bio that is also completed through a end_workqueue_fn() work item. However, __btrfs_correct_data_nocsum() waits for the newly submitted bio to complete, thus it depends on another work item. This example currently usually works because we use different workqueue helper functions for BTRFS_WQ_ENDIO_DATA and BTRFS_WQ_ENDIO_DIO_REPAIR. However, it may deadlock with stacked filesystems and is fragile overall. The proper fix is to free the work item at the very end of the work function, so let's do that. Reviewed-by:
Omar Sandoval <osandov@fb.com> Reviewed-by:
-
Chuhong Yuan authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 04358e40 ] The driver misses calling clk_unprepare in probe failure and remove. Add the calls to fix it. Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Lianbo Jiang authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 112eee5d ] Add a forward declaration of struct kimage to the crash.h header because future changes will invoke a crash-specific function from the realmode init path and the compiler will complain otherwise like this: In file included from arch/x86/realmode/init.c:11: ./arch/x86/include/asm/crash.h:5:32: warning: ‘struct kimage’ declared inside\ parameter list will not be visible outside of this definition or declaration 5 | int crash_load_segments(struct kimage *image); | ^~~~~~ ./arch/x86/include/asm/crash.h:6:37: warning: ‘struct kimage’ declared inside\ parameter list will not be visible outside of this definition or declaration 6 | int crash_copy_backup_region(struct kimage *image); | ^~~~~~ ./arch/x86/include/asm/crash.h:7:39: warning: ‘struct kimage’ declared inside\ parameter list will not be visible outside of this definition or declaration 7 | int crash_setup_memmap_entries(struct kimage *image, | [ bp: Rewrite the commit message. ] Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Lianbo Jiang <lijiang@redhat.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: bhe@redhat.com Cc: d.hatayama@fujitsu.com Cc: dhowells@redhat.com Cc: dyoung@redhat.com Cc: ebiederm@xmission.com Cc: horms@verge.net.au Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jürgen Gross <jgross@suse.com> Cc: kexec@lists.infradead.org Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: vgoyal@redhat.com Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20191108090027.11082-4-lijiang@redhat.com Link: https://lkml.kernel.org/r/201910310233.EJRtTMWP%25lkp@intel.comSigned-off-by:
-
Viresh Kumar authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 46770be0 ] The cpufreq core heavily depends on the availability of the struct device for CPUs and if they aren't available at the time cpufreq driver is registered, we will never succeed in making cpufreq work. This happens due to following sequence of events: - cpufreq_register_driver() - subsys_interface_register() - return 0; //successful registration of driver ... at a later point of time - register_cpu(); - device_register(); - bus_probe_device(); - sif->add_dev(); - cpufreq_add_dev(); - get_cpu_device(); //FAILS - per_cpu(cpu_sys_devices, num) = &cpu->dev; //used by get_cpu_device() - return 0; //CPU registered successfully Because the per-cpu variable cpu_sys_devices is set only after the CPU device is regsitered, cpufreq will never be able to get it when cpufreq_add_dev() is called. This patch avoids this failure by making sure device structure of at least CPU0 is available when the cpufreq driver is registered, else return -EPROBE_DEFER. Reported-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Co-developed-by:
Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Tested-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Sudip Mukherjee authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 231ec2f2 ] Usually all the distro will load the parport low level driver as part of their initialization. But we can get into a situation where all the parallel port drivers are built as module and we unload all the modules at a later time. Then if we just do "modprobe parport" it will only load the parport module and will not load the low level driver which will actually register the ports. So, check the bus if there is any parport registered, if not, load the low level driver. We can get into the above situation with all distro but only Suse has setup the alias for "parport_lowlevel" and so it only works in Suse. Users of Debian based distro will need to load the lowlevel module manually. Signed-off-by:
Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/r/20191016144540.18810-3-sudipm.mukherjee@gmail.comSigned-off-by:
-
Ben Zhang authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit eabf424f ] The codec dies when RT5677_PWR_ANLG2(MX-64h) is set to 0xACE1 while it's streaming audio over SPI. The DSP firmware turns on PLL2 (MX-64 bit 8) when SPI streaming starts. However regmap does not believe that register can change by itself. When BST1 (bit 15) is turned on with regmap_update_bits(), it doesn't read the register first before write, so PLL2 power bit is cleared by accident. Marking MX-64h as volatile in regmap solved the issue. Signed-off-by:
Ben Zhang <benzh@chromium.org> Signed-off-by:
Curtis Malainey <cujomalainey@chromium.org> Link: https://lore.kernel.org/r/20191106011335.223061-6-cujomalainey@chromium.orgSigned-off-by:
-
Chuhong Yuan authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 5eb263ef ] pxa2xx_spi_init_pdata misses checks for devm_clk_get and platform_get_irq. Add checks for them to fix the bugs. Since ssp->clk and ssp->irq are used in probe, they are mandatory here. So we cannot use _optional() for devm_clk_get and platform_get_irq. Signed-off-by:
-
Robert Richter authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 7088e29e ] The current code to convert a physical address mask to a grain (defined as granularity in bytes) is: e->grain = ~(mem_err->physical_addr_mask & ~PAGE_MASK); This is broken in several ways: 1) It calculates to wrong grain values. E.g., a physical address mask of ~0xfff should give a grain of 0x1000. Without considering PAGE_MASK, there is an off-by-one. Things are worse when also filtering it with ~PAGE_MASK. This will calculate to a grain with the upper bits set. In the example it even calculates to ~0. 2) The grain does not depend on and is unrelated to the kernel's page-size. The page-size only matters when unmapping memory in memory_failure(). Smaller grains are wrongly rounded up to the page-size, on architectures with a configurable page-size (e.g. arm64) this could round up to the even bigger page-size of the hypervisor. Fix this with: e->grain = ~mem_err->physical_addr_mask + 1; The grain_bits are defined as: grain = 1 << grain_bits; Change also the grain_bits calculation accordingly, it is the same formula as in edac_mc.c now and the code can be unified. The value in ->physical_addr_mask coming from firmware is assumed to be contiguous, but this is not sanity-checked. However, in case the mask is non-contiguous, a conversion to grain_bits effectively converts the grain bit mask to a power of 2 by rounding it up. Suggested-by:
James Morse <james.morse@arm.com> Signed-off-by:
Robert Richter <rrichter@marvell.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org> Cc: Tony Luck <tony.luck@intel.com> Link: https://lkml.kernel.org/r/20191106093239.25517-11-rrichter@marvell.comSigned-off-by:
-
Chuhong Yuan authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 2df200ab ] The driver misses calling v4l2_ctrl_handler_free and v4l2_device_unregister in remove like what is done in probe failure. Add the calls to fix it. Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by:
-
Mike Isely authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 7f404ae9 ] In some device configurations there's no radio or radio support in the driver. That's OK, as the driver sets itself up accordingly. However on tear-down in these caes it's still trying to tear down radio related context when there isn't anything there, leading to dereferences through a null pointer and chaos follows. How this bug survived unfixed for 11 years in the pvrusb2 driver is a mystery to me. [hverkuil: fix two checkpatch warnings] Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Miaoqing Pan authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 05a11003 ] ath10k does not provide transmit rate info per MSDU in tx completion, mark that as -1 so mac80211 will ignore the rates. This fixes mac80211 update Mesh link metric with invalid transmit rate info. Tested HW: QCA9984 Tested FW: 10.4-3.9.0.2-00035 Signed-off-by:
Hou Bao Hou <houbao@codeaurora.org> Signed-off-by:
Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by:
Miaoqing Pan <miaoqing@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit da6cb952 ] Filter out instances except for inlined_subroutine and subprogram DIE in die_walk_instances() and die_is_func_instance(). This fixes an issue that perf probe sets some probes on calling address instead of a target function itself. When perf probe walks on instances of an abstruct origin (a kind of function prototype of inlined function), die_walk_instances() can also pass a GNU_call_site (a GNU extension for call site) to callback. Since it is not an inlined instance of target function, we have to filter out when searching a probe point. Without this patch, perf probe sets probes on call site address too.This can happen on some function which is marked "inlined", but has actual symbol. (I'm not sure why GCC mark it "inlined"): # perf probe -D vfs_read p:probe/vfs_read _text+2500017 p:probe/vfs_read_1 _text+2499468 p:probe/vfs_read_2 _text+2499563 p:probe/vfs_read_3 _text+2498876 p:probe/vfs_read_4 _text+2498512 p:probe/vfs_read_5 _text+2498627 With this patch: Slightly different results, similar tho: # perf probe -D vfs_read p:probe/vfs_read _text+2498512 Committer testing: # uname -a Linux quaco 5.3.8-200.fc30.x86_64 #1 SMP Tue Oct 29 14:46:22 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux Before: # perf probe -D vfs_read p:probe/vfs_read _text+3131557 p:probe/vfs_read_1 _text+3130975 p:probe/vfs_read_2 _text+3131047 p:probe/vfs_read_3 _text+3130380 p:probe/vfs_read_4 _text+3130000 # uname -a Linux quaco 5.3.8-200.fc30.x86_64 #1 SMP Tue Oct 29 14:46:22 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux # After: # perf probe -D vfs_read p:probe/vfs_read _text+3130000 # Fixes: db0d2c64 ("perf probe: Search concrete out-of-line instances") Signed-off-by:
Masami Hiramatsu <mhiramat@kernel.org> Tested-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit f4d99bdf ] Skip end-of-sequence and non-statement lines while walking through lines list. The "end-of-sequence" line information means: "the current address is that of the first byte after the end of a sequence of target machine instructions." (DWARF version 4 spec 6.2.2) This actually means out of scope and we can not probe on it. On the other hand, the statement lines (is_stmt) means: "the current instruction is a recommended breakpoint location. A recommended breakpoint location is intended to “represent” a line, a statement and/or a semantically distinct subpart of a statement." (DWARF version 4 spec 6.2.2) So, non-statement line info also should be skipped. These can reduce unneeded probe points and also avoid an error. E.g. without this patch: # perf probe -a "clear_tasks_mm_cpumask:1" Added new events: probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask:1) probe:clear_tasks_mm_cpumask_1 (on clear_tasks_mm_cpumask:1) probe:clear_tasks_mm_cpumask_2 (on clear_tasks_mm_cpumask:1) probe:clear_tasks_mm_cpumask_3 (on clear_tasks_mm_cpumask:1) probe:clear_tasks_mm_cpumask_4 (on clear_tasks_mm_cpumask:1) You can now use it in all perf tools, such as: perf record -e probe:clear_tasks_mm_cpumask_4 -aR sleep 1 # This puts 5 probes on one line, but acutally it's not inlined function. This is because there are many non statement instructions at the function prologue. With this patch: # perf probe -a "clear_tasks_mm_cpumask:1" Added new event: probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask:1) You can now use it in all perf tools, such as: perf record -e probe:clear_tasks_mm_cpumask -aR sleep 1 # Now perf-probe skips unneeded addresses. Committer testing: Slightly different results, but similar: Before: # uname -a Linux quaco 5.3.8-200.fc30.x86_64 #1 SMP Tue Oct 29 14:46:22 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux # # perf probe -a "clear_tasks_mm_cpumask:1" Added new events: probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask:1) probe:clear_tasks_mm_cpumask_1 (on clear_tasks_mm_cpumask:1) probe:clear_tasks_mm_cpumask_2 (on clear_tasks_mm_cpumask:1) You can now use it in all perf tools, such as: perf record -e probe:clear_tasks_mm_cpumask_2 -aR sleep 1 # After: # perf probe -a "clear_tasks_mm_cpumask:1" Added new event: probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask:1) You can now use it in all perf tools, such as: perf record -e probe:clear_tasks_mm_cpumask -aR sleep 1 # perf probe -l probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask@kernel/cpu.c) # Fixes: 4cc9cec6 ("perf probe: Introduce lines walker interface") Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 86c0bf85 ] Fix to show calling lines of inlined functions (where an inline function is called). die_walk_lines() filtered out the lines inside inlined functions based on the address. However this also filtered out the lines which call those inlined functions from the target function. To solve this issue, check the call_file and call_line attributes and do not filter out if it matches to the line information. Without this fix, perf probe -L doesn't show some lines correctly. (don't see the lines after 17) # perf probe -L vfs_read <vfs_read@/home/mhiramat/ksrc/linux/fs/read_write.c:0> 0 ssize_t vfs_read(struct file *file, char __user *buf, size_t count, loff_t *pos) 1 { 2 ssize_t ret; 4 if (!(file->f_mode & FMODE_READ)) return -EBADF; 6 if (!(file->f_mode & FMODE_CAN_READ)) return -EINVAL; 8 if (unlikely(!access_ok(buf, count))) return -EFAULT; 11 ret = rw_verify_area(READ, file, pos, count); 12 if (!ret) { 13 if (count > MAX_RW_COUNT) count = MAX_RW_COUNT; 15 ret = __vfs_read(file, buf, count, pos); 16 if (ret > 0) { fsnotify_access(file); add_rchar(current, ret); } With this fix: # perf probe -L vfs_read <vfs_read@/home/mhiramat/ksrc/linux/fs/read_write.c:0> 0 ssize_t vfs_read(struct file *file, char __user *buf, size_t count, loff_t *pos) 1 { 2 ssize_t ret; 4 if (!(file->f_mode & FMODE_READ)) return -EBADF; 6 if (!(file->f_mode & FMODE_CAN_READ)) return -EINVAL; 8 if (unlikely(!access_ok(buf, count))) return -EFAULT; 11 ret = rw_verify_area(READ, file, pos, count); 12 if (!ret) { 13 if (count > MAX_RW_COUNT) count = MAX_RW_COUNT; 15 ret = __vfs_read(file, buf, count, pos); 16 if (ret > 0) { 17 fsnotify_access(file); 18 add_rchar(current, ret); } 20 inc_syscr(current); } Fixes: 4cc9cec6 ("perf probe: Introduce lines walker interface") Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit c701636a ] Make find_best_scope() returns innermost DIE at given address if there is no best matched scope DIE. Since Gcc sometimes generates intuitively strange line info which is out of inlined function address range, we need this fixup. Without this, sometimes perf probe failed to probe on a line inside an inlined function: # perf probe -D ksys_open:3 Failed to find scope of probe point. Error: Failed to add events. With this fix, 'perf probe' can probe it: # perf probe -D ksys_open:3 p:probe/ksys_open _text+25707308 p:probe/ksys_open_1 _text+25710596 p:probe/ksys_open_2 _text+25711114 p:probe/ksys_open_3 _text+25711343 p:probe/ksys_open_4 _text+25714058 p:probe/ksys_open_5 _text+2819653 p:probe/ksys_open_6 _text+2819701 Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit dee36a2a ] Since debuginfo__find_probes() callback function can be called with the location which already passed, the callback function must filter out such overlapped locations. add_probe_trace_event() has already done it by commit 1a375ae7 ("perf probe: Skip same probe address for a given line"), but add_available_vars() doesn't. Thus perf probe -v shows same address repeatedly as below: # perf probe -V vfs_read:18 Available variables at vfs_read:18 @<vfs_read+217> char* buf loff_t* pos ssize_t ret struct file* file @<vfs_read+217> char* buf loff_t* pos ssize_t ret struct file* file @<vfs_read+226> char* buf loff_t* pos ssize_t ret struct file* file With this fix, perf probe -V shows it correctly: # perf probe -V vfs_read:18 Available variables at vfs_read:18 @<vfs_read+217> char* buf loff_t* pos ssize_t ret struct file* file @<vfs_read+226> char* buf loff_t* pos ssize_t ret struct file* file Fixes: cf6eb489 ("perf probe: Show accessible local variables") Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 18e21eb6 ] Fix 'perf probe --line' option to show inlined function callsite lines even if the function DIE has only ranges. Without this: # perf probe -L amd_put_event_constraints ... 2 { 3 if (amd_has_nb(cpuc) && amd_is_nb_event(&event->hw)) __amd_put_nb_event_constraints(cpuc, event); 5 } With this patch: # perf probe -L amd_put_event_constraints ... 2 { 3 if (amd_has_nb(cpuc) && amd_is_nb_event(&event->hw)) 4 __amd_put_nb_event_constraints(cpuc, event); 5 } Committer testing: Before: [root@quaco ~]# perf probe -L amd_put_event_constraints <amd_put_event_constraints@/usr/src/debug/kernel-5.2.fc30/linux-5.2.18-200.fc30.x86_64/arch/x86/events/amd/core.c:0> 0 static void amd_put_event_constraints(struct cpu_hw_events *cpuc, struct perf_event *event) 2 { 3 if (amd_has_nb(cpuc) && amd_is_nb_event(&event->hw)) __amd_put_nb_event_constraints(cpuc, event); 5 } PMU_FORMAT_ATTR(event, "config:0-7,32-35"); PMU_FORMAT_ATTR(umask, "config:8-15" ); [root@quaco ~]# After: [root@quaco ~]# perf probe -L amd_put_event_constraints <amd_put_event_constraints@/usr/src/debug/kernel-5.2.fc30/linux-5.2.18-200.fc30.x86_64/arch/x86/events/amd/core.c:0> 0 static void amd_put_event_constraints(struct cpu_hw_events *cpuc, struct perf_event *event) 2 { 3 if (amd_has_nb(cpuc) && amd_is_nb_event(&event->hw)) 4 __amd_put_nb_event_constraints(cpuc, event); 5 } PMU_FORMAT_ATTR(event, "config:0-7,32-35"); PMU_FORMAT_ATTR(umask, "config:8-15" ); [root@quaco ~]# perf probe amd_put_event_constraints:4 Added new event: probe:amd_put_event_constraints (on amd_put_event_constraints:4) You can now use it in all perf tools, such as: perf record -e probe:amd_put_event_constraints -aR sleep 1 [root@quaco ~]# [root@quaco ~]# perf probe -l probe:amd_put_event_constraints (on amd_put_event_constraints:4@arch/x86/events/amd/core.c) probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask@kernel/cpu.c) [root@quaco ~]# Using it: [root@quaco ~]# perf trace -e probe:* ^C[root@quaco ~]# Ok, Intel system here... :-) Fixes: 4cc9cec6 ("perf probe: Introduce lines walker interface") Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit af04dd2f ] Fix to show ranges of variables (--range and --vars option) in functions which DIE has only ranges but no entry_pc attribute. Without this fix: # perf probe --range -V clear_tasks_mm_cpumask Available variables at clear_tasks_mm_cpumask @<clear_tasks_mm_cpumask+0> (No matched variables) With this fix: # perf probe --range -V clear_tasks_mm_cpumask Available variables at clear_tasks_mm_cpumask @<clear_tasks_mm_cpumask+0> [VAL] int cpu @<clear_tasks_mm_cpumask+[0-35,317-317,2052-2059]> Committer testing: Before: [root@quaco ~]# perf probe --range -V clear_tasks_mm_cpumask Available variables at clear_tasks_mm_cpumask @<clear_tasks_mm_cpumask+0> (No matched variables) [root@quaco ~]# After: [root@quaco ~]# perf probe --range -V clear_tasks_mm_cpumask Available variables at clear_tasks_mm_cpumask @<clear_tasks_mm_cpumask+0> [VAL] int cpu @<clear_tasks_mm_cpumask+[0-23,23-105,105-106,106-106,1843-1850,1850-1862]> [root@quaco ~]# Using it: [root@quaco ~]# perf probe clear_tasks_mm_cpumask cpu Added new event: probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask with cpu) You can now use it in all perf tools, such as: perf record -e probe:clear_tasks_mm_cpumask -aR sleep 1 [root@quaco ~]# perf probe -l probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask@kernel/cpu.c with cpu) [root@quaco ~]# [root@quaco ~]# perf trace -e probe:*cpumask ^C[root@quaco ~]# Fixes: 349e8d26 ("perf probe: Add --range option to show a variable's location range") Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit eb6933b2 ] Fix perf probe to probe an inlne function which has no entry pc or low pc but only has ranges attribute. This seems very rare case, but I could find a few examples, as same as probe_point_search_cb(), use die_entrypc() to get the entry address in probe_point_inline_cb() too. Without this patch: # perf probe -D __amd_put_nb_event_constraints Failed to get entry address of __amd_put_nb_event_constraints. Probe point '__amd_put_nb_event_constraints' not found. Error: Failed to add events. With this patch: # perf probe -D __amd_put_nb_event_constraints p:probe/__amd_put_nb_event_constraints amd_put_event_constraints+43 Committer testing: Before: [root@quaco ~]# perf probe -D __amd_put_nb_event_constraints Failed to get entry address of __amd_put_nb_event_constraints. Probe point '__amd_put_nb_event_constraints' not found. Error: Failed to add events. [root@quaco ~]# After: [root@quaco ~]# perf probe -D __amd_put_nb_event_constraints p:probe/__amd_put_nb_event_constraints _text+33789 [root@quaco ~]# Fixes: 4ea42b18 ("perf: Add perf probe subcommand, a kprobe-event setup helper") Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit acb6a704 ] Since some inlined functions are in lexical blocks of given function, we have to recursively walk through the DIE tree. Without this fix, perf-probe -L can miss the inlined functions which is in a lexical block (like if (..) { func() } case.) However, even though, to walk the lines in a given function, we don't need to follow the children DIE of inlined functions because those do not have any lines in the specified function. We need to walk though whole trees only if we walk all lines in a given file, because an inlined function can include another inlined function in the same file. Fixes: b0e9cb28 ("perf probe: Fix to search nested inlined functions in CU") Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 3895534d ] Since debuginfo__find_probe_point() uses dwarf_entrypc() for finding the entry address of the function on which a probe is, it will fail when the function DIE has only ranges attribute. To fix this issue, use die_entrypc() instead of dwarf_entrypc(). Without this fix, perf probe -l shows incorrect offset: # perf probe -l probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask+18446744071579263632@work/linux/linux/kernel/cpu.c) probe:clear_tasks_mm_cpumask_1 (on clear_tasks_mm_cpumask+18446744071579263752@work/linux/linux/kernel/cpu.c) With this: # perf probe -l probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask@work/linux/linux/kernel/cpu.c) probe:clear_tasks_mm_cpumask_1 (on clear_tasks_mm_cpumask:21@work/linux/linux/kernel/cpu.c) Committer testing: Before: [root@quaco ~]# perf probe -l probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask+18446744071579765152@kernel/cpu.c) [root@quaco ~]# After: [root@quaco ~]# perf probe -l probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask@kernel/cpu.c) [root@quaco ~]# Fixes: 1d46ea2a ("perf probe: Fix listing incorrect line number with inline function") Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit b77afa1f ] Fix die_is_func_instance() to find range-only function instance. In some case, a function instance can be made without any low PC or entry PC, but only with address ranges by optimization. (e.g. cold text partially in "text.unlikely" section) To find such function instance, we have to check the range attribute too. Fixes: e1ecbbc3 ("perf probe: Fix to handle optimized not-inlined functions") Signed-off-by:
-
Ping-Ke Shih authored
BugLink: https://bugs.launchpad.net/bugs/1858462 [ Upstream commit 5174f1e4 ] This leak was found by testing the EDIMAX EW-7612 on Raspberry Pi 3B+ with Linux 5.4-rc5 (multi_v7_defconfig + rtlwifi + kmemleak) and noticed a single memory leak during probe: unreferenced object 0xec13ee40 (size 176): comm "kworker/u8:1", pid 36, jiffies 4294939321 (age 5580.790s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<fc1bbb3e>] __netdev_alloc_skb+0x9c/0x164 [<863dfa6e>] rtl92c_set_fw_rsvdpagepkt+0x254/0x340 [rtl8192c_common] [<9572be0d>] rtl92cu_set_hw_reg+0xf48/0xfa4 [rtl8192cu] [<116df4d8>] rtl_op_bss_info_changed+0x234/0x96c [rtlwifi] [<8933575f>] ieee80211_bss_info_change_notify+0xb8/0x264 [mac80211] [<d4061e86>] ieee80211_assoc_success+0x934/0x1798 [mac80211] [<e55adb56>] ieee80211_rx_mgmt_assoc_resp+0x174/0x314 [mac80211] [<5974629e>] ieee80211_sta_rx_queued_mgmt+0x3f4/0x7f0 [mac80211] [<d91091c6>] ieee80211_iface_work+0x208/0x318 [mac80211] [<ac5fcae4>] process_one_work+0x22c/0x564 [<f5e6d3b6>] worker_thread+0x44/0x5d8 [<82c7b073>] kthread+0x150/0x154 [<b43e1b7d>] ret_from_fork+0x14/0x2c [<794dff30>] 0x0 It is because 8192cu doesn't implement usb_cmd_send_packet(), and this patch just frees the skb within the function to resolve memleak problem by now. Since 8192cu doesn't turn on fwctrl_lps that needs to download command packet for firmware via the function, applying this patch doesn't affect driver behavior. Reported-by:
Stefan Wahren <wahrenst@gmx.net> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
