- 04 Apr, 2011 18 commits
-
-
Helmut Schaa authored
Move the HT40 check inside the calculation function to make it easier for a later cleanup. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
We can simply check if the driver registered the watchdog callback. There's no need to have an additional flag for that. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Instead of hardcoding the tx status fifo size as 512 calculate it based on the number of tx queues and the number of entries per queue. Also round the size up to a power of 2 as kfifo would otherwise round it down. On rt2800pci this will increase the kfifo size from 512 bytes to 1024 bytes which is then able to hold the tx status for all entries in all tx queues. Furthermore, if the number of tx queues or tx entries changes in the future (use of the MGMT queue for example) the kfifo size doesn't need to be updated. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Instead of reporting an unlimited number of tx status reports to mac80211 stop after 16 frames and reschedule the tx status tasklet. This allows other tasklets to be run inbetween. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Instead of receiving an unlimited number of frames, stop after 16 entries and reschedule the rxdone tasklet. This allows other tasklets to be run inbetween. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
Remove some unused variables and correct spelling errors. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Marc Yang authored
The hw_dot_11n_dev_cap reported by firmware hw_spec has different format than the 11n capabilities. Hence a lot of SET_ and RESET_ bit operation macros were used to convert the dev_cap format to 11n capability format. However the locally defined 11n ht_cap macros are not necessary as we can use IEEE80211_HT_CAP_ macros directly. The 32-bit dev_cap bitmap is added as comment to explain the mapping between firmware and 11n spec. Some unused macros and unnecessary adapter variables are also removed. Signed-off-by: Marc Yang <yangyang@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bing Zhao authored
and SHORT_SLOT_TIME_ENABLED. Use WLAN_CAPABILITY_SHORT_SLOT_TIME instead. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
The only thing that using crypto_blkcipher with ecb does over just using arc4 directly is wrapping the encrypt/decrypt function into a for loop, looping over each individual character. To be able to do this, it pulls in around 40 kb worth of unnecessary kernel modules (at least on a MIPS embedded device). Using arc4 directly not only eliminates those dependencies, it also makes the code smaller. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Marc Yang authored
mwifiex_set_encrypt_mode() mwifiex_set_auth_mode() mwifiex_set_auth() These functions are confusing and misleading. And they are really not needed at all. Some unused definitions are also removed. Signed-off-by: Marc Yang <yangyang@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Yogesh Ashok Powar authored
'iw list' is sufficient to retrieve the information which was displayed by these functions. Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
The commit "mac80211: reply to directed probes in IBSS" changed ad-hoc specific code to respond to unicast probe requests, even if drv_tx_last_beacon returns false, however due to confusion over the meaning of the IEEE80211_RX_RA_MATCH flag, it also unconditionally enabled responding to multicast probe requests. Fix this by explicitly checking for a multicast destination address instead. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
This function is nowhere used. Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
This does not seems to be used anywhere so remove it. Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Greear authored
Aids debugging wifi behaviour. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
Add iwlegacy driver to MAINTAINERS. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6
-
- 30 Mar, 2011 22 commits
-
-
Felix Fietkau authored
It has the same purpose (and value) as ah->config.max_txtrig_level Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
It is not used anywhere Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Similar to the number of tx queue, the number of keycache entries depends on the chip and shouldn't be messed with based on EEPROM data. Remove this field and stick to using AR_KEYTABLE_SIZE Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
It is not used anywhere and seems pointless Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
It is only used in one place, and the device id check that it's based on can be moved there as well. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
The EEPROM contains a field that can restrict the number of hardware queues, however this is not only useless (all the known chips contain the same number of hardware queues), but also potentially dangerous in case of a misprogrammed EEPROM (could trigger driver crashes), so let's just ignore it completely. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
RF_BANK_SETUP, REG_WRITE_RF_ARRAY and REG_WRITE_ARRAY are way too big, so they shouldn't be inlined at every single callsite, especially since they can easily be turned into real functions. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
It's easier to read and it slightly decreases code size Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Reduces the number of calls to register ops. On MIPS this reduces the ath9k_hw binary size from 321k down to 310k Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
With this change, loading the address to a register read/write function costs only one pointer dereference instead of two. On MIPS this reduces ath9k_hw binary size from 326k down to 321k. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
Indicate an NL80211_CMD_DEL_STATION event when a station entry in mac80211 is deleted to match with the NL80211_CMD_NEW_STATION event that is used when the entry was added. This is needed, e.g., to allow user space to remove a peer from RSN IBSS Authenticator state machine to avoid re-authentication and re-keying delays when the peer is not reachable anymore. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
Add support for using RSN IBSS with ath9k. For now, this uses software crypto for group addressed frames in RSN IBSS, but that may be optimized in the future by extending the key cache design to support per-STA RX GTK. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Stuck beacon detection is supposed to trigger when 9 consecutive beacons could not be sent by the hardware. When the driver runs only one active AP mode interface, it still configures the hardware beacon timer for 4 (ATH_BCBUF) beacon slots slots, which causes stuck beacon detection to be reset if ath9k_hw_stoptxdma clears the stuck frames between SWBA intervals. Fix this by not resetting the missed beacon count for empty slots and multiplying the threshold not by the maximum number of beacon slots but by the configured number of beacon interfaces. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Single missed (i.e. not transmitted) beacons in AP mode are not very rare and not necessarily an indicator of strong interference, so only trigger noise floor recalibration when multiple consecutive beacons could not be transmitted. Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
AP mode beacon timers in ath9k are configured in milliseconds, which breaks when increasing ATH_BCBUF to 8 instead of 4 (due to rounding errors). Since the hardware timers are actually configured in microseconds, it's better to let the driver use that unit directly. To be able to do that, the beacon interval parameter abuse for passing certain flags needs to be removed. This is easy to do, because those flags are completely unnecessary anyway. ATH9K_BEACON_ENA is ignored, ATH9K_BEACON_RESET_TSF can be replaced with calling ath9k_hw_reset_tsf from the driver directly. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vasily Khoruzhick authored
Add support for suspend/resume in if_spi. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Bing Zhao authored
This driver adds WiFi support for Marvell 802.11n based chipsets with SDIO interface. Currently only SD8787 is supported. More chipsets will be supported later. drivers/net/wireless/mwifiex/ Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kiran Divekar <dkiran@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Marc Yang <yangyang@marvell.com> Signed-off-by: Ramesh Radhakrishnan <rramesh@marvell.com> Signed-off-by: Frank Huang <frankh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
Only AR9485 1.1 was sold. This debloats the driver by ~14 KiB. text data bss dec hex filename 300413 624 1056 302093 49c0d drivers/net/wireless/ath/ath9k/ath9k_hw.ko text data bss dec hex filename 310285 624 1056 311965 4c29d drivers/net/wireless/ath/ath9k/ath9k_hw-old.ko $ du -b ath9k_hw* 6210541 ath9k_hw.ko 6225089 ath9k_hw-old.ko Cc: Bill Wu <bill.wu@atheros.com> Cc: Paul Shaw <paul.shaw@atheros.com> Cc: Forbes Tsai <Forbes.Tsai@Atheros.com> Cc: Jesmine Chen <jesmine.chen@atheros.com> Cc: Marvian Chen <Hou-hua.Chen@Atheros.com> Cc: Vivek Natarajan <vivek.natarajan@atheros.com> Cc: Bernadette Yetso <bernadette.yetso@atheros.com> Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com> Acked-by: Yi-Chen Su <yi-chen.su@atheros.com> Acked-by: Jeffrey Chung <jeffrey.chung@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
ieee80211_tx_status iterates over all tx rates the driver reports back in order to 1) mark tx rates as invalid if the driver cannot have tried that rate 2) find the actually used tx rate for the final retransmission By leaving the for loop when the first invalid rate index is found we can move the rates_idx assignment after the loop and therefore save a few assignments and conditionals. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
This workaround called ath_txq_schedule whenever there were still pending frames for a queue, but the queue depth was zero. Because of its its high false positive probability (e.g. with paused TIDs) and because it is in the way of other pending work (AP powersave fixes), it is better to remove this code entirely. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Most AR9100 devices already have a chainmask of 7 (three antennas), however on the ones that don't (rx and tx chainmask set to 5), problems with IQ mismatch calibration have been observed. This shows up as tx queue hangs (and subsequent hardware resets) if traffic is sent during this type of calibration. Forcing the rx chainmask to 7 fixes the calibration issues with no apparent negative side effects on throughput and stability. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Fixes interop issues with aggregation in combination with multi-BSSID Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-