- 13 May, 2016 9 commits
-
-
Hariprasad S authored
In abort_arp_failure(), the return value from c4iw_ofld_send() is ignored and thus if the CPL isn't sent, the endpoint is stuck and never gets aborted. Failure of c4iw_ofld_send() is treated as fatal error, and the ep resources are released in a safer context through process_work(). Signed-off-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
Doug Ledford <dledford@redhat.com>
-
Hariprasad S authored
Moving the state to ABORTING causes the ep to get stuck because c4iw_ep_timeout() thinks the ABORT has already been done. So leave the state alone and let c4iw_ep_disconnect() do the right thing given the ep state. Signed-off-by:
-
Hariprasad S authored
->In act_open_rpl(), CPL_ERR_TCAM_FULL error handling branch, there is no handling of the return value of send_fw_act_open_req(). ->In send_fw_act_open_req(), there is no handling of return value of c4iw_l2t_send(), which may cause a ep leak and won't notify upper layers on connection establish failure. ->send_mpa_req() should act on the return from c4iw_l2t_send() and return the error to the caller. ->In case of c4iw_l2t_send() failure in send_mpa_req(), returns without starting the timer and not changing the ep state, which is further handled by act_establish() -> In act_establish()?if send_mpa_request's get_skb returns an error, may cause an ep leak. So handle return value of send_mpa_req() Signed-off-by:
-
Hariprasad S authored
->Stop the ep timer after MPA negotiation so that the arp failures during send_mpa_reply/reject will be handled by process_timeout() after the ep timer expires. ->Added case MPA_REP_SENT in process_timeout(). ->For MPA reject, c4iw_ep_disconnect tries to start an already started timer, which leads to warning message "timer already started". -> In case of mpa reject stop the timer and call send_mpa_reject(). -> Added new ep flag STOP_MPA_TIMER to tell fw4_ack() to stop the timer only for send_mpa_reply(), which is set in c4iw_accept_cr(). Signed-off-by:
-
Hariprasad S authored
In case of incomplete mpa messages we should not stop timer as it results in return with timeout for the next mpa message Signed-off-by:
-
Hariprasad S authored
-> On passive side of connection parent_ep referenced during connection request has to be dereferenced during the passive accept failure. -> As passive accept failure error handlinglogic runs in atomic context, the parent ep is dereferenced by scheduling work request. Signed-off-by:
-
Hariprasad S authored
The FID value in a ULP_MEMIO command needs to be set to an IQ ID of a queue configured for our PF. The FID/IQ id is used to index into the PCIE FID table, to find out on which function the DMA needs to be issued. Essentially, every DMA needs to have the ingress queue. The exact ingress queue doesn't matter, but it needs to be an ingress queue associated with the function you want to see the DMA on. Signed-off-by:
-
Hariprasad S authored
Signed-off-by:
-
Hariprasad S authored
- add EP_DISC_FAIL history bit - add QP_REFED/DEREFED history bits - Add functions to ref/deref the cm_id and add history bit for the same - add CLOSE_CON_RPL history Signed-off-by:
-
- 12 May, 2016 11 commits
-
-
Doug Ledford authored
-
Saeed Mahameed authored
Adding the needed mlx5_ifc hardware bits and structs for the following features: * Add vport to steering commands for SRIOV ACL support * Add mlcr, pcmr and mcia registers for dump module EEPROM * Add support for FCS, beacon led and disable_link bits to hca caps * Add CQE period mode bit in CQ context for CQE based CQ moderation support * Add umr SQ bit for fragmented memory registration * Add needed bits and caps for Striding RQ support In-order to avoid possible future conflicts between rdma and net-next we added all expected updates to this file for this release. If more changes will be submitted, we plan to do it only through one of the subsystems, probably net-next. All updated bits in this patch will be later used in the up-coming submissions to net-next and rdma trees. Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Matan Barak <matanb@mellanox.com> Acked-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Tariq Toukan authored
All reserved fields after early_vf_enable are off by 1, since early_vf_enable was not explicitly declared as array of size 1. Reserved field before cqe_zip had a wrong size, it should be 0x80 + 0x3f. Fixes: b0844444 ("net/mlx5_core: Introduce access function to read internal timer ") Fixes: b4ff3a36 ("net/mlx5: Use offset based reserved field names in the IFC header file") Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Bart Van Assche authored
Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Sagi Grimberg <sagi@grimberg.me> Cc: Laurence Oberman <loberman@redhat.com> Reviewed-by:
Sagi Grimberg <sai@grimberg.m> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Bart Van Assche authored
Since all srp_map_finish_fr() callers pass a non-zero value as the fourth argument (sg_nents), the sg_nents == 0 check in that function can be removed. Add a count == 0 check in the caller of that function. Signed-off-by:
Sagi Grimberg <sagi@grimberg.me> Reviewed-by:
-
Bart Van Assche authored
The srp_queuecommand() function translates ENOMEM into QUEUE_FULL which causes the SCSI mid-layer to retry the command. All other error codes are translated into DID_ERROR which causes the SCSI command to fail. Return E2BIG if mapping will always fail to prevent that the SCSI mid-layer keeps resubmitting a command forever. Signed-off-by:
-
Bart Van Assche authored
This patch does not change any functionality. Signed-off-by:
Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Laurence Oberman <loberman@redhat.com> Reviewed-by:
-
Bart Van Assche authored
Ensure that req->nmdesc is set correctly in srp_map_sg() if mapping fails. Avoid that mapping failure causes a memory descriptor leak. Report srp_map_sg() failure to the caller. Signed-off-by:
-
Bart Van Assche authored
Signed-off-by:
-
Bart Van Assche authored
The free request list was removed through patch "IB/srp: Use block layer tags". Hence update a comment that refers to that free request list. Signed-off-by:
-
Bart Van Assche authored
Change one occurrence of "boundries" into "boundaries". Signed-off-by:
-
- 05 May, 2016 11 commits
-
-
Doug Ledford authored
-
Hariprasad S authored
Use c4iw_ep_disconnect() instead. This is part of getting rid of abort_connection() altogether so we properly clean up on send_abort() failures. This is the last user of abort_connection(), so remove it too. Signed-off-by:
-
Hariprasad S authored
In c4iw_ep_disconnect(), if we fail to initiate a close operation, then move the qp to ERROR to disassociate the ep from the qp. Failure to do this will leak the ep resources. Signed-off-by:
-
Hariprasad S authored
Instead return whether the caller needs to disconnect. This is part of getting rid of abort_connection() altogether so we properly clean up on send_abort() failures. Signed-off-by:
-
Hariprasad S authored
Use c4iw_ep_disconnect() instead. This is part of getting rid of abort_connection() altogether so we properly clean up on send_abort() failures. Signed-off-by:
-
Hariprasad S authored
Signed-off-by:
-
Hariprasad S authored
Instead, have the caller, rx_data() handle the close/abort like it does for process_mpa_request(). This is part of getting rid of abort_connection() altogether so we properly clean up on send_abort() failures. Signed-off-by:
-
Hariprasad S authored
In rx_data(), with the ep in FPDU_MODE, refcnt=2, if we get unexpected streaming data, we call c4iw_modify_rc_qp() and move the qp from RTS -> TERMINATE. In c4iw_modify_rc_qp(), if rdma_fini() returns an error, the ep will be dereferenced (refcnt=1). Then rx_data() calls c4iw_ep_disconnect() which starts the close operation. But if send_halfclose() fails in c4iw_ep_disconnect(), we will call release_ep_resources() derefing the ep which reduces the refcnt to 0 and and frees the ep. However we still has the ep mutex at that point, so we have a touch-after-free bug. There is a similar issue where peer_close() calls c4iw_ep_disconnect(). The solution is to add a reference to the ep in c4iw_ep_disconnect() after acquiring the mutex, and release it after releasing the mutex. Signed-off-by:
-
Hariprasad S authored
In c4iw_ep_disconnect(), if we start the ep timer to begin a close, but send_halfclose() fails, we need to stop the timer and send a CLOSE event up to the IWCM before releasing the resources. Otherwise, we can crash when the ep timer fires if the ep is referencing a previous instance of the device. This can happen as part of adapter reset/recovery, for instance. Signed-off-by:
-
Hariprasad S authored
If ARP fails before the CPL_PASS_ACCEPT_RPL is seen by hardware, the tid will be stuck in SYN_PEND and never released. So create an arp failure handler specifically for this message to release the endpoint resources. In pass_accept_rpl_arp_failure(), put the parent endpoint so it will be freed when destroyed. Also we don't need to call release_tid() here because _c4iw_free_ep() calls cxgb4_remove_tid() which releases the hwtid. If we get an ABORT_REQ_RSS instead of a PASS_ESTABLISH (because the peer's ACK to our SYN is never received), then put the parent as well in peer_abort(). Treat accept_cr() failures just like arp failures: put the parent ep and release the ep resources destroying the tid The ARP failure handlers are called in an atomic context, so we need to schedule some of the processing which might block. Namely _c4iw_free_ep() which needs a mutex. So create a "special" CPL opcode and handler and schedule it via sched() to be run by process_work() in a blockable context. Also rework the active open arp failure handler to make use of release_ep_resources(). This allows both the active and passive arp failure handlers to use the same deferred cleanup function. Signed-off-by:
-
Christoph Hellwig authored
iSER currently has a couple places that set max_sectors in either the host template or SCSI host, and all of them get it wrong. This patch instead uses a single assignment that (hopefully) gets it right: the max_sectors value must be derived from the number of segments in the FR or FMR structure, but actually be one lower than the page size multiplied by the number of sectors, as it has to handle the case of non-aligned I/O. Without this I get trivial to reproduce hangs when running xfstests (on XFS) over iSER to Linux targets. Signed-off-by:
Max Gurtovoy <maxg@mellanox.com> Acked-by:
-
- 29 Apr, 2016 1 commit
-
-
Florian Westphal authored
Alternatively one could free the skb, OTOH I don't think this test is useful so just remove it. Cc: <linux-rdma@vger.kernel.org> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
- 28 Apr, 2016 8 commits
-
-
Tatyana Nikolova authored
Fix for removing a quad hash entry when the corresponding quad hash entry hasn't been added, which is the case in loopback connections Signed-off-by:
Tatyana Nikolova <Tatyana.E.Nikolova@intel.com> Signed-off-by:
Faisal Latif <faisal.latif@intel.com> Signed-off-by:
-
Tatyana Nikolova authored
Fix for checking if the QP associated with a completion has been destroyed while processing CQ elements. If that is the case, move the CQ head to the next element and continue completion processing. Signed-off-by:
-
Shiraz Saleem authored
A check is added to validate the requested sge number. iWARP doesn't support multiple sg elements for RDMA READ work requests. Signed-off-by:
-
Shiraz Saleem authored
Fix to calculate the SQ size based on the max frag_count, requested by the application instead of overwriting it with the max supported frag_count Signed-off-by:
-
Mohammad Khan authored
Fix for filling in the WQE size for NOP Signed-off-by:
-
Chien Tin Tung authored
STag index mask is calculated incorrectly, missing the 14 bits minimum requirement. Add max macro to use either # of MRs or 14 bits in the mask size calculation. Signed-off-by:
-
Shiraz Saleem authored
Invalidation after every WQE write is changed to invalidate only if required. NOPs are padded so that WQE writes are aligned to 64B boundary. Signed-off-by:
-
Ismail, Mustafa authored
Adding sq and rq drain functions, which block until all previously posted wr-s in the specified queue have completed. A completion object is signaled to unblock the thread, when the last cqe for the corresponding queue is processed. Signed-off-by:
Mustafa Ismail <mustafa.ismail@intel.com> Signed-off-by:
-
