Offloading device drivers will mark offloaded MACsec SKBs with the
corresponding SCI in the skb_metadata_dst so the macsec rx handler will
know to which interface to divert those skbs, in case of a marked skb
and a mismatch on the dst MAC address, divert the skb to the macsec
net_device where the macsec rx_handler will be called to consider cases
where relying solely on the dst MAC address is insufficient.

One such instance is when using MACsec with a VLAN as an inner
header, where the packet structure is ETHERNET | SECTAG | VLAN.
In such a scenario, the dst MAC address in the ethernet header
will correspond to the VLAN MAC address, resulting in a mismatch.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Offloading MACsec when its configured over VLAN with current MACsec
TX steering rules will wrongly insert MACsec sec tag after inserting
the VLAN header leading to a ETHERNET | SECTAG | VLAN packet when
ETHERNET | VLAN | SECTAG is configured.

The above issue is due to adding the SECTAG by HW which is a later
stage compared to the VLAN header insertion stage.

Detect such a case and adjust TX steering rules to insert the
SECTAG in the correct place by using reformat_param_0 field in
the packet reformat to indicate the offset of SECTAG from end of
the MAC header to account for VLANs in granularity of 4Bytes.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MACsec device may have a VLAN device on top of it.
Detect MACsec state correctly under this condition,
and return the correct net device accordingly.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable MACsec offload feature over VLAN by adding NETIF_F_HW_MACSEC
to the device vlan_features.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for MACsec offload operations for VLAN driver
to allow offloading MACsec when VLAN's real device supports
Macsec offload by forwarding the offload request to it.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: fix a plenty of flexible-array-nested warnings

Paolo noticed a compile warning in SCTP,

../net/sctp/stream_sched_fc.c: note: in included file (through ../include/net/sctp/sctp.h):
../include/net/sctp/structs.h:335:41: warning: array of flexible structures

But not only this, there are actually quite a lot of such warnings in
some SCTP structs. This patchset fixes most of warnings by deleting
these nested flexible array members.

After this patchset, there are still some warnings left:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  ./include/net/sctp/structs.h:1145:41: warning: nested flexible array
  ./include/uapi/linux/sctp.h:641:34: warning: nested flexible array
  ./include/uapi/linux/sctp.h:643:34: warning: nested flexible array
  ./include/uapi/linux/sctp.h:644:33: warning: nested flexible array
  ./include/uapi/linux/sctp.h:650:40: warning: nested flexible array
  ./include/uapi/linux/sctp.h:653:39: warning: nested flexible array

the 1st is caused by __data[] in struct ip_options, not in SCTP;
the others are in uapi, and we should not touch them.

Note that instead of completely deleting it, we just leave it as a
comment in the struct, signalling to the reader that we do expect
such variable parameters over there, as Marcelo suggested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array payload[] from the structure
sctp_datahdr to avoid some sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/socket.c: note: in included file (through include/net/sctp/structs.h, include/net/sctp/sctp.h):
  ./include/linux/sctp.h:230:29: warning: nested flexible array

This member is not even used anywhere.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array hmac[] from the structure
sctp_authhdr to avoid some sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/auth.c: note: in included file (through include/net/sctp/structs.h, include/net/sctp/sctp.h):
  ./include/linux/sctp.h:735:29: warning: nested flexible array
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array peer_init[] from the structure
sctp_cookie to avoid some sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/sm_make_chunk.c: note: in included file (through include/net/sctp/sctp.h):
  ./include/net/sctp/structs.h:1588:28: warning: nested flexible array
  ./include/net/sctp/structs.h:343:28: warning: nested flexible array
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array variable[] from the structure
sctp_sackhdr and sctp_errhdr to avoid some sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/sm_statefuns.c: note: in included file (through include/net/sctp/structs.h, include/net/sctp/sctp.h):
  ./include/linux/sctp.h:451:28: warning: nested flexible array
  ./include/linux/sctp.h:393:29: warning: nested flexible array
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array skip[] from the structure
sctp_ifwdtsn/fwdtsn_hdr to avoid some sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/stream_interleave.c: note: in included file (through include/net/sctp/structs.h, include/net/sctp/sctp.h):
  ./include/linux/sctp.h:611:32: warning: nested flexible array
  ./include/linux/sctp.h:628:33: warning: nested flexible array
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array params[] from the structure
sctp_inithdr, sctp_addiphdr and sctp_reconf_chunk to avoid some
sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/input.c: note: in included file (through include/net/sctp/structs.h, include/net/sctp/sctp.h):
  ./include/linux/sctp.h:278:29: warning: nested flexible array
  ./include/linux/sctp.h:675:30: warning: nested flexible array

This warning is reported if a structure having a flexible array
member is included by other structures.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johannes Berg says:

====================
net: extend drop reasons

Here's v4 of the extended drop reasons, with fixes to kernel-doc
and checkpatch.
====================

Link: https://lore.kernel.org/r/20230419125254.20789-1-johannes@sipsolutions.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

It can be really hard to analyse or debug why packets are
going missing in mac80211, so add the needed infrastructure
to use use the new per-subsystem drop reasons.

We actually use two drop reason subsystems here because of
the different handling of frames that are dropped but still
go to monitor for old versions of hostapd, and those that
are just completely unusable (e.g. crypto failed.)

Annotate a few reasons here just to illustrate this, we'll
need to go through and annotate more of them later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Extend drop reasons to make them usable by subsystems
other than core by reserving the high 16 bits for a
new subsystem ID, of which 0 of course is used for the
existing reasons immediately.

To still be able to have string reasons, restructure
that code a bit to make the loopup under RCU, the only
user of this (right now) is drop_monitor.

Link: https://lore.kernel.org/netdev/00659771ed54353f92027702c5bbb84702da62ce.camel@sipsolutions.netSigned-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This will, after the next patch, hold only the core
drop reasons and minimal infrastructure. Fix a small
kernel-doc issue while at it, to avoid the move
triggering a checker.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ICMPv6 error packets are not sent to the anycast destinations and this
prevents things like traceroute from working. So create a setting similar
to ECHO when dealing with Anycast sources (icmpv6_echo_ignore_anycast).
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20230419013238.2691167-1-maheshb@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Vladimir Oltean says:

====================
ethtool mm API consolidation

This series consolidates the behavior of the 2 drivers that implement
the ethtool MAC Merge layer by making NXP ENETC commit its preemptible
traffic classes to hardware only when MM TX is active (same as Ocelot).

Then, after resolving an issue with the ENETC driver, it restricts user
space from entering 2 states which don't make sense:

- pmac-enabled off tx-enabled on  verify-enabled *
- pmac-enabled *   tx-enabled off verify-enabled on

Then, it introduces a selftest (ethtool_mm.sh) which puts everything
together and tests all valid configurations known to me.

This is simultaneously the v2 of "[PATCH net-next 0/2] ethtool mm API
improvements":
https://lore.kernel.org/netdev/20230415173454.3970647-1-vladimir.oltean@nxp.com/
which had caused some problems to openlldp. Those were solved in the
meantime, see:
https://github.com/intel/openlldp/commit/11171b474f6f3cbccac5d608b7f26b32ff72c651

and of "[RFC PATCH net-next] selftests: forwarding: add a test for MAC
Merge layer":
https://lore.kernel.org/netdev/20230210221243.228932-1-vladimir.oltean@nxp.com/
====================

Link: https://lore.kernel.org/r/20230418111459.811553-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The MAC Merge layer (IEEE 802.3-2018 clause 99) does all the heavy
lifting for Frame Preemption (IEEE 802.1Q-2018 clause 6.7.2), a TSN
feature for minimizing latency.

Preemptible traffic is different on the wire from normal traffic in
incompatible ways. If we send a preemptible packet and the link partner
doesn't support preemption, it will drop it as an error frame and we
will never know. The MAC Merge layer has a control plane of its own,
which can be manipulated (using ethtool) in order to negotiate this
capability with the link partner (through LLDP).

Actually the TLV format for LLDP solves this problem only partly,
because both partners only advertise:
- if they support preemption (RX and TX)
- if they have enabled preemption (TX)
so we cannot tell the link partner what to do - we cannot force it to
enable reception of our preemptible packets.

That is fully solved by the verification feature, where the local device
generates some small probe frames which look like preemptible frames
with no useful content, and the link partner is obliged to respond to
them if it supports the standard. If the verification times out, we know
that preemption isn't active in our TX direction on the link.

Having clarified the definition, this selftest exercises the manual
(ethtool) configuration path of 2 link partners (with and without
verification), and the LLDP code path, using the openlldp project.

The test also verifies the TX activity of the MAC Merge layer by
sending traffic through a traffic class configured as preemptible
(using mqprio). There isn't a good way to make this really portable
(user space cannot find out how many traffic classes there are for
a device), but I chose num_tc 4 here, that should work reasonably well.
I also know that some devices (stmmac) only permit TXQ0 to be
preemptible, so this is why PREEMPTIBLE_PRIO was strategically chosen
as 0. Even if other hardware is more configurable, this test should
cover the baseline.

This is not really a "forwarding" selftest, but I put it near the other
"ethtool" selftests.

$ ./ethtool_mm.sh eno0 swp0
TEST: Manual configuration with verification: eno0 to swp0          [ OK ]
TEST: Manual configuration with verification: swp0 to eno0          [ OK ]
TEST: Manual configuration without verification: eno0 to swp0       [ OK ]
TEST: Manual configuration without verification: swp0 to eno0       [ OK ]
TEST: Manual configuration with failed verification: eno0 to swp0   [ OK ]
TEST: Manual configuration with failed verification: swp0 to eno0   [ OK ]
TEST: LLDP                                                          [ OK ]
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Counters for the MAC Merge layer and preemptible MAC have standardized
so far on using structured ethtool stats as opposed to the driver
specific names and meanings.

Benefit from that rare opportunity and introduce a helper to lib.sh for
querying standardized counters, in the hope that these will take off for
other uses as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw selftests often invoke a bail_on_lldpad() helper to make sure LLDPAD
is not running, to prevent conflicts between the QoS configuration applied
through TC or DCB command line tool, and the DCB configuration that LLDPAD
might apply. This helper might be useful to others. Move the function to
lib.sh, and parameterize to make reusable in other contexts.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The driver-specific wrappers of these selftests invoke bail_on_lldpad to
make sure that LLDPAD doesn't trample the configuration. The function
bail_on_lldpad is going to move to lib.sh in the next patch. With that, it
won't be visible for the wrappers before sourcing the framework script. And
after sourcing it, it is too late: the selftest will have run by then.

One option might be to source NUM_NETIFS=0 lib.sh from the wrapper, but
even if that worked (it might, it might not), that seems cumbersome. lib.sh
is doing fair amount of stuff, and even if it works today, it does not look
particularly solid as a solution.

Instead, introduce a hook, sch_tbf_pre_hook(), that when available, gets
invoked. Move the bail to the hook.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The verify-enabled boolean (ETHTOOL_A_MM_VERIFY_ENABLED) was intended to
be a sub-setting of tx-enabled (ETHTOOL_A_MM_TX_ENABLED). IOW, MAC Merge
TX can be enabled with or without verification, but verification with TX
disabled makes no sense.

The pmac-enabled boolean (ETHTOOL_A_MM_PMAC_ENABLED) was intended to be
a global toggle from an API perspective, whereas tx-enabled just handles
the TX direction. IOW, the pMAC can be enabled with or without TX, but
it doesn't make sense to enable TX if the pMAC is not enabled.

Add two checks which sanitize and reject these invalid cases.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

These have been useful in debugging various problems related to frame
preemption, so make them available through ethtool --register-dump for
later too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This was left as TODO in commit 01e23b2b ("net: enetc: add support
for preemptible traffic classes") since it's relatively complicated.

Where this makes a difference is with a configuration as follows:

ethtool --set-mm eno0 pmac-enabled on tx-enabled on verify-enabled on

Preemptible packets should only be sent when the MAC Merge TX direction
becomes active (i.o.w. when the verification process succeeds, aka when
the link partner confirms it can process preemptible traffic). But the
tc qdisc with the preemptible traffic classes is offloaded completely
asynchronously w.r.t. the MM becoming active.

The ENETC manual does suggest that this should be handled in the driver:
"On startup, software should wait for the verification process to
complete (MMCSR[VSTS]=011) before initiating traffic".

Adding the necessary logic allows future selftests to uphold the claim
that an inactive or disabled MAC Merge layer should never send data
packets through the pMAC.

This change moves enetc_set_ptcfpr() from enetc.c to enetc_ethtool.c,
where its only caller is now - enetc_mm_commit_preemptible_tcs().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The MMCSR register contains 2 fields with overlapping meaning:

- LPA (Local preemption active):
This read-only status bit indicates whether preemption is active for
this port. This bit will be set if preemption is both enabled and has
completed the verification process.
- TXSTS (Merge status):
This read-only status field provides the state of the MAC Merge sublayer
transmit status as defined in IEEE Std 802.3-2018 Clause 99.
00 Transmit preemption is inactive
01 Transmit preemption is active
10 Reserved
11 Reserved

However none of these 2 fields offer reliable reporting to software.

When connecting ENETC to a link partner which is not capable of Frame
Preemption, the expectation is that ENETC's verification should fail
(VSTS=4) and its MM TX direction should be inactive (LPA=0, TXSTS=00)
even though the MM TX is enabled (ME=1). But surprise, the LPA bit of
MMCSR stays set even if VSTS=4 and ME=1.

OTOH, the TXSTS field has the opposite problem. I cannot get its value
to change from 0, even when connecting to a link partner capable of
frame preemption, which does respond to its verification frames (ME=1
and VSTS=3, "SUCCEEDED").

The only option with such buggy hardware seems to be to reimplement the
formula for calculating tx-active in software, which is for tx-enabled
to be true, and for the verify-status to be either SUCCEEDED, or
DISABLED.

Without reliable tx-active reporting, we have no good indication when
to commit the preemptible traffic classes to hardware, which makes it
possible (but not desirable) to send preemptible traffic to a link
partner incapable of receiving it. However, currently we do not have the
logic to wait for TX to be active yet, so the impact is limited.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Current enetc_set_mm() is designed to set the priv->active_offloads bit
ENETC_F_QBU for enetc_mm_link_state_update() to act on, but if the link
is already up, it modifies the ENETC_MMCSR_ME ("Merge Enable") bit
directly.

The problem is that it only *sets* ENETC_MMCSR_ME if the link is up, it
doesn't *clear* it if needed. So subsequent enetc_get_mm() calls still
see tx-enabled as true, up until a link down event, which is when
enetc_mm_link_state_update() will get called.

This is not a functional issue as far as I can assess. It has only come
up because I'd like to uphold a simple API rule in core ethtool code:
the pMAC cannot be disabled if TX is going to be enabled. Currently,
the fact that TX remains enabled for longer than expected (after the
enetc_set_mm() call that disables it) is going to violate that rule,
which is how it was caught.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Refer to USB serial device or net device, there is a notice to
let end user know the status of device, like attached or
disconnected. Add attach/disconnect print for wwan device as
well.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/20230420023617.3919569-1-slark_xiao@163.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

__kfree_skb_defer() uses the old naming where "defer" meant
slab bulk free/alloc APIs. In the meantime we also made
__kfree_skb_defer() feed the per-NAPI skb cache, which
implies bulk APIs. So take away the 'defer' and add 'napi'.

While at it add a drop reason. This only matters on the
tx_action path, if the skb has a frag_list. But getting
rid of a SKB_DROP_REASON_NOT_SPECIFIED seems like a net
benefit so why not.
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20230420020005.815854-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix the following warning about risky iterator use:

drivers/net/ethernet/mellanox/mlx5/core/eq.c:1010 mlx5_comp_irq_get_affinity_mask() warn: iterator used outside loop: 'eq'
Acked-by: Saeed Mahameed <saeed@kernel.org>
Link: https://lore.kernel.org/r/20230420015802.815362-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Address a number of warnings flagged by
./scripts/kernel-doc -none include/net/flow_dissector.h

 include/net/flow_dissector.h:23: warning: Function parameter or member 'addr_type' not described in 'flow_dissector_key_control'
 include/net/flow_dissector.h:23: warning: Function parameter or member 'flags' not described in 'flow_dissector_key_control'
 include/net/flow_dissector.h:46: warning: Function parameter or member 'padding' not described in 'flow_dissector_key_basic'
 include/net/flow_dissector.h:145: warning: Function parameter or member 'tipckey' not described in 'flow_dissector_key_addrs'
 include/net/flow_dissector.h:157: warning: cannot understand function prototype: 'struct flow_dissector_key_arp '
 include/net/flow_dissector.h:171: warning: cannot understand function prototype: 'struct flow_dissector_key_ports '
 include/net/flow_dissector.h:203: warning: cannot understand function prototype: 'struct flow_dissector_key_icmp '

Also improve indentation on adjacent lines to those changed
to address the above.

No functional changes intended.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230419-flow-dissector-kdoc-v1-1-1aa0cca1118b@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jesper points out that we must prevent recycling into cache
after page_pool_destroy() is called, because page_pool_destroy()
is not synchronized with recycling (some pages may still be
outstanding when destroy() gets called).

I assumed this will not happen because NAPI can't be scheduled
if its page pool is being destroyed. But I missed the fact that
NAPI may get reused. For instance when user changes ring configuration
driver may allocate a new page pool, stop NAPI, swap, start NAPI,
and then destroy the old pool. The NAPI is running so old page
pool will think it can recycle to the cache, but the consumer
at that point is the destroy() path, not NAPI.

To avoid extra synchronization let the drivers do "unlinking"
during the "swap" stage while NAPI is indeed disabled.

Fixes: 8c48eea3 ("page_pool: allow caching from safely localized NAPI")
Reported-by: Jesper Dangaard Brouer <jbrouer@redhat.com>
Link: https://lore.kernel.org/all/e8df2654-6a5b-3c92-489d-2fe5e444135f@redhat.com/Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/20230419182006.719923-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The CONFIG_PHYLIB symbol is selected by a number of device drivers that
need PHY support, but it now has a dependency on CONFIG_LEDS_CLASS,
which may not be enabled, causing build failures.

Avoid the risk of missing and circular dependencies by guarding the
phylib LED support itself in another Kconfig symbol that can only be
enabled if the dependency is met.

This could be made a hidden symbol and always enabled when both CONFIG_OF
and CONFIG_LEDS_CLASS are reachable from the phylib, but there may be an
advantage in having users see this option when they have a misconfigured
kernel without built-in LED support.

Fixes: 01e5b728 ("net: phy: Add a binding for PHY LEDs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230420084624.3005701-1-arnd@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Adjacent changes:

net/mptcp/protocol.h
  63740448 ("mptcp: fix accept vs worker race")
  2a6a870e ("mptcp: stops worker on unaccepted sockets at listener close")
  ddb1a072 ("mptcp: move first subflow allocation at mpc access time")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This partially reverts commit e161d4b6.

Turns out the channelmap variable is not actually read-only, it's modified
through the MCI_GPM_CLR_CHANNEL_BIT() macro further down in the function,
so making it read-only causes page faults when that code is hit.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=217183
Link: https://lore.kernel.org/r/20230413214118.153781-1-toke@toke.dk
Fixes: e161d4b6 ("wifi: ath9k: Make arrays prof_prio and channelmap static const")
Cc: stable@vger.kernel.org
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull Rust fixes from Miguel Ojeda:
 "Most of these are straightforward.

  The last one is more complex, but it only touches Rust + GCC builds
  which are for the moment best-effort.

   - Code: Missing 'extern "C"' fix.

   - Scripts: 'is_rust_module.sh' and 'generate_rust_analyzer.py' fixes.

   - A couple trivial fixes

   - Build: Rust + GCC build fix and 'grep' warning fix"

* tag 'rust-fixes-6.3' of https://github.com/Rust-for-Linux/linux:
  rust: allow to use INIT_STACK_ALL_ZERO
  rust: fix regexp in scripts/is_rust_module.sh
  rust: build: Fix grep warning
  scripts: generate_rust_analyzer: Handle sub-modules with no Makefile
  rust: kernel: Mark rust_fmt_argument as extern "C"
  rust: sort uml documentation arch support table
  rust: str: fix requierments->requirements typo

Pull networking fixes from Paolo Abeni:
 "Including fixes from netfilter and bpf.

  There are a few fixes for new code bugs, including the Mellanox one
  noted in the last networking pull. No known regressions outstanding.

  Current release - regressions:

   - sched: clear actions pointer in miss cookie init fail

   - mptcp: fix accept vs worker race

   - bpf: fix bpf_arch_text_poke() with new_addr == NULL on s390

   - eth: bnxt_en: fix a possible NULL pointer dereference in unload
     path

   - eth: veth: take into account peer device for
     NETDEV_XDP_ACT_NDO_XMIT xdp_features flag

  Current release - new code bugs:

   - eth: revert "net/mlx5: Enable management PF initialization"

  Previous releases - regressions:

   - netfilter: fix recent physdev match breakage

   - bpf: fix incorrect verifier pruning due to missing register
     precision taints

   - eth: virtio_net: fix overflow inside xdp_linearize_page()

   - eth: cxgb4: fix use after free bugs caused by circular dependency
     problem

   - eth: mlxsw: pci: fix possible crash during initialization

  Previous releases - always broken:

   - sched: sch_qfq: prevent slab-out-of-bounds in qfq_activate_agg

   - netfilter: validate catch-all set elements

   - bridge: don't notify FDB entries with "master dynamic"

   - eth: bonding: fix memory leak when changing bond type to ethernet

   - eth: i40e: fix accessing vsi->active_filters without holding lock

  Misc:

   - Mat is back as MPTCP co-maintainer"

* tag 'net-6.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (33 commits)
  net: bridge: switchdev: don't notify FDB entries with "master dynamic"
  Revert "net/mlx5: Enable management PF initialization"
  MAINTAINERS: Resume MPTCP co-maintainer role
  mailmap: add entries for Mat Martineau
  e1000e: Disable TSO on i219-LM card to increase speed
  bnxt_en: fix free-runnig PHC mode
  net: dsa: microchip: ksz8795: Correctly handle huge frame configuration
  bpf: Fix incorrect verifier pruning due to missing register precision taints
  hamradio: drop ISA_DMA_API dependency
  mlxsw: pci: Fix possible crash during initialization
  mptcp: fix accept vs worker race
  mptcp: stops worker on unaccepted sockets at listener close
  net: rpl: fix rpl header size calculation
  net: vmxnet3: Fix NULL pointer dereference in vmxnet3_rq_rx_complete()
  bonding: Fix memory leak when changing bond type to Ethernet
  veth: take into account peer device for NETDEV_XDP_ACT_NDO_XMIT xdp_features flag
  mlxfw: fix null-ptr-deref in mlxfw_mfa2_tlv_next()
  bnxt_en: Fix a possible NULL pointer dereference in unload path
  bnxt_en: Do not initialize PTP on older P3/P4 chips
  netfilter: nf_tables: tighten netlink attribute requirements for catch-all elements
  ...

When wx_alloc_page_pool() failed in wx_setup_rx_resources(), it doesn't
release DMA buffer. Add dma_free_coherent() in the error path to release
the DMA buffer.

Fixes: 850b9711 ("net: libwx: Allocate Rx and Tx resources")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230418065450.2268522-1-shaozhengchao@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

There is a structural problem in switchdev, where the flag bits in
struct switchdev_notifier_fdb_info (added_by_user, is_local etc) only
represent a simplified / denatured view of what's in struct
net_bridge_fdb_entry :: flags (BR_FDB_ADDED_BY_USER, BR_FDB_LOCAL etc).
Each time we want to pass more information about struct
net_bridge_fdb_entry :: flags to struct switchdev_notifier_fdb_info
(here, BR_FDB_STATIC), we find that FDB entries were already notified to
switchdev with no regard to this flag, and thus, switchdev drivers had
no indication whether the notified entries were static or not.

For example, this command:

ip link add br0 type bridge && ip link set swp0 master br0
bridge fdb add dev swp0 00:01:02:03:04:05 master dynamic

has never worked as intended with switchdev. It causes a struct
net_bridge_fdb_entry to be passed to br_switchdev_fdb_notify() which has
a single flag set: BR_FDB_ADDED_BY_USER.

This is further passed to the switchdev notifier chain, where interested
drivers have no choice but to assume this is a static (does not age) and
sticky (does not migrate) FDB entry. So currently, all drivers offload
it to hardware as such, as can be seen below ("offload" is set).

bridge fdb get 00:01:02:03:04:05 dev swp0 master
00:01:02:03:04:05 dev swp0 offload master br0

The software FDB entry expires $ageing_time centiseconds after the
kernel last sees a packet with this MAC SA, and the bridge notifies its
deletion as well, so it eventually disappears from hardware too.

This is a problem, because it is actually desirable to start offloading
"master dynamic" FDB entries correctly - they should expire $ageing_time
centiseconds after the *hardware* port last sees a packet with this
MAC SA - and this is how the current incorrect behavior was discovered.
With an offloaded data plane, it can be expected that software only sees
exception path packets, so an otherwise active dynamic FDB entry would
be aged out by software sooner than it should.

With the change in place, these FDB entries are no longer offloaded:

bridge fdb get 00:01:02:03:04:05 dev swp0 master
00:01:02:03:04:05 dev swp0 master br0

and this also constitutes a better way (assuming a backport to stable
kernels) for user space to determine whether the kernel has the
capability of doing something sane with these or not.

As opposed to "master dynamic" FDB entries, on the current behavior of
which no one currently depends on (which can be deduced from the lack of
kselftests), Ido Schimmel explains that entries with the "extern_learn"
flag (BR_FDB_ADDED_BY_EXT_LEARN) should still be notified to switchdev,
since the spectrum driver listens to them (and this is kind of okay,
because although they are treated identically to "static", they are
expected to not age, and to roam).

Fixes: 6b26b51b ("net: bridge: Add support for notifying devices about FDB add/del")
Link: https://lore.kernel.org/netdev/20230327115206.jk5q5l753aoelwus@skbuf/Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230418155902.898627-1-vladimir.oltean@nxp.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

This reverts commit fe998a3c.

Paul reports that it causes a regression with IB on CX4
and FW 12.18.1000. In addition I think that the concept
of "management PF" is not fully accepted and requires
a discussion.

Fixes: fe998a3c ("net/mlx5: Enable management PF initialization")
Reported-by: Paul Moore <paul@paul-moore.com>
Link: https://lore.kernel.org/all/CAHC9VhQ7A4+msL38WpbOMYjAqLp0EtOjeLh4Dc6SQtD6OUvCQg@mail.gmail.com/
Link: https://lore.kernel.org/r/20230413222547.56901-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>