* Add an extra argument to ide_max_dma_mode() for passing requested transfer
  mode.  Use it as an upper limit when finding the best DMA for device/host.

* Rename ide_max_dma_mode() to ide_find_dma_mode() and at the same time add
  ide_max_dma_mode() wrapper which passes XFER_UDMA_6 as a requested mode to
  ide_find_dma_mode().  Also add inline ide_find_dma_mode() version for
  CONFIG_BLK_DEV_IDEDMA=n case.

* Pass requested transfer mode from ide_find_dma_mode() to ide_get_mode_mask()
  to avoid false warning from eighty_ninty_three().

* Use ide_find_dma_mode() to limit the user requested transfer mode in
  ide_rate_filter().  Also limit the requested mode by host max PIO mode.


Above changes make ide_rate_filter() to:

* Clip desired transfer mode down if it is invalid (values 0x0F, 0x13-0x19
  and 0x25-0x39, values > 0x46 were already clipped down, same for values
  0x25-0x39 but iff UDMA was not supported by the host).

* Clip desired transfer mode down if it is currently unsupported by IDE core
  (PIO6 and MWDMA3-4, the latter were already clipped down but iff UDMA was
  not supported by the host).

* Clip desired transfer mode down according to the host capabilities
  (UDMA modes were already clipped down but MWDMA/SWDMA/PIO weren't,
  also ->atapi_dma flag was not respected).

* Clip desired transfer mode down according to the device capabilities
  (except PIO modes for now which require mode work) - shouldn't be a
  problem since ide_set_xfer_rate() is called _after_ device has accepted
  given transfer mode.

and also result in a number of host driver specific bugfixes:

* icside
  - clip unsupported PIO5 mode down
  - fix unsupported/invalid modes being set in drive->current_speed

* ide-cris
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
  - fix BUG() on unsupported/invalid modes

* au1xxx-ide
  - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2
    (if BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=n) modes down

* aec62xx
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
  - fix 0x00 being programmed as PIO timing for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* alim15x3
  - clip DMA modes down for ATAPI devices (chipset revision == 0x20 only)
  - fix theoretical OOPS for 0x0F mode
  - fix unsupported/invalid modes being set on the device

* amd74xx
  - clip unsupported SWDMA0-2 (on COBRA_7401 revs <= 7) modes down
  - fix random PIO timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* atiixp
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix cached MWDMA mode being cleared for unsupported/invalid modes
  - fix PIO{0,2} timings being programmed for unsupported/invalid modes
  - fix theoretical OOPS for PIO5-6 and 0x0F modes
  - fix unsupported/invalid modes being set on the device

* cmd64x
  - clip unsupported SWDMA0-2 modes down

* cs5530
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix BUG() on unsupported/invalid modes
    (which happened if the device accepted the setting)

* cs5535
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix theoretical OOPS for PIO5-6 and 0x0F modes

* hpt34x
  - clip DMA modes down for ATAPI devices
  - fix invalid timings being programmed for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* hpt366
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix PIO0 timings being programmed for unsupported/invalid modes
  - fix DMA timings being cleared for MWDMA3-4 and 0x25-0x39 modes
  - fix unsupported/invalid modes being set on the device

* it8213
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* it821x
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
    (chipset in smart mode and revision 0x10 in pass-through mode)

* jmicron
  - clip unsupported SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device

* pdc202xx_new
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device

* pdc202xx_old
  - clip unsupported PIO5 mode down
  - fix incorrect timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* piix
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* sc1200
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix BUG() on unsupported/invalid modes
    (which happened if the device accepted the setting)

* scc_pata
  - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2 modes down

* serverworks
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix DMA/UDMA timings/settings being cleared for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* siimage
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices (SATA chipsets)

* sis5513
  - clip unsupported PIO5 mode down
  - fix BUG() on unsupported/invalid modes

* sl82c105
  - clip unsupported SWDMA0-2 modes down

* slc90e66
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* tc86c001
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix PIO0 timings being programmed for PIO5/0x0F/SWDMA0-2/0x13-0x19 modes
  - fix invalid 0x00 DMA timing being programmed for MWDMA3-4/0x25-0x39 modes
  - fix unsupported/invalid modes being set on the device

* triflex
  - clip unsupported PIO5 mode down

* via82cxxx
  - fix random PIO timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* pmac
  - clip unsupported PIO5 and SWDMA0-2 modes down

* cmd640/ht6560b
  - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
  - fix PIO5 being clipped to PIO4 (if CONFIG_BLK_DEV_IDEDMA=n)

* opti621
  - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
  - clip unsupported PIO4 to PIO3 (if CONFIG_BLK_DEV_IDEDMA=n)


While at it:

* Use ide_rate_filter() in cs5520.c::cs5520_tune_chipset().

* Remove no longer needed checks from hpt366.c::hpt3{6,7}x_tune_chipset().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Fix icside, cris-ide, au1xxx-ide, amd74xx, via82cxxx and pmac host drivers
  to use ide_rate_filter().

  This results in the following modes (from user requests) being clipped down:
  - invalid modes (values 0x46-0xFF)  [ for all hosts ]
  - unsupported by a host UDMA modes  [ for hosts which support UDMA]
  - all UDMA modes and MWDMA3-4 modes [ for hosts which don't support UDMA ]
  - invalid modes (values 0x25-0x39)  [ for hosts which don't support UDMA ]

* Host driver specific changes in behavior:

  icside:
    - no change

  cris-ide
    - clip unsupported UDMA3-6 modes down
    - fix BUG() on trying to set unsupported UDMA3-6 modes

  au1xxx-ide/pmac
    - clip unsupported UDMA modes down

  amd74xx/via82cxxx
    - clip unsupported UDMA modes down
    - fix random PIO timings being set for unsupported/invalid modes
    - fix unsupported/invalid modes being set on the device

* While at it remove no longer needed checks from pmac.c driver.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Give the udma_filter() method call precedence over using the mode masks.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

PATA part of all current JMB controllers behave the same way and
JMicron confirms that all future ones will stay compatible.  Matching
vendor and device class is enough.

For backward compatibility, jmicron still needs to match 361,3,5,6,8
DIDs regardless of device class if libata is not configured but won't
need further DID update from this point.

Bart: cosmetic fixes to jmicron_chipset
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ethan Hsiao <ethanhsiao@jmicron.com>
Cc: Justin Tsai <justin@jmicron.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Switch to using pci_get_slot() in init_setup_pdc20270() to get to the mate chip
behind DC21150 bridge as there's no need for the driver itself to walk the list
of the PCI devices (and the driver didn't check the bus # of the found device).
While at it, make it emit warning about IRQ # being fixed up (just like hpt366.c
does) and "beautify" this whole function as well as init_setup_pdc20276()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ACPI spec defines the sequence of IDE power on/off:
Powering down:
	Call _GTM.
	Power down drive (calls _PS3 method and turns off power planes).
Powering up:
	Power up drive (calls _PS0 method if present and turns on power planes).
	Call _STM passing info from _GTM (possibly modified), with ID data from
	each drive.
	Initialize the channel.
	May modify the results of _GTF.
	For each drive:
		Call _GTF.
		Execute task file (possibly modified).
This patch adds the missed _PS0/_PS3 methods call.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This is now very similar to pata_platform.c, they both use
same platform data structure and same resources.

To achieve that, byte_lanes_swapping platform data variable
and platform specified iops removed from that driver. It's fine,
since those were never used anyway.

pata_platform and ide_platform are carrying same driver names,
to easily switch between these drivers, without need to touch
platform code.

Bart:
- build fix from Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the MWDMA modes (at least that could be seen in their so-called drivers :-),
so the driver needs to account for this -- to achieve this:

- add mdma_filter() method from the original patch by Bartlomiej Zolnierkiewicz
  with his consent;

- install the method for all chips to only return empty mask if a SATA drive
  is detected on HPT372{AN]/374 chips...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

SB700 supports one physical IDE channel, but SB700 SATA controller
supports combined mode.  When the SATA combined mode is enabled,
two SATA ports (port4 and port5) share one IDE channel from IDE
controller, and PATA will share the other IDE channel.

Our previous patch adding SB700 IDE device ID only supports one
IDE channel, which contains bug.  The attached patch fixes the bug.
Signed-off-by: "Shane Huang" <Shane.Huang@amd.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Au1000: set the PCI controller IO base
  [MIPS] Alchemy: Fix USB initialization.
  [MIPS] IP32: Fix fatal typo in address computation.

The recent fix for a circular lock dependency unfortunately introduced a
potential memory leak in the event where the call to nlmsvc_lookup_host
fails for some reason.

Thanks to Roel Kluin for spotting this.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The recent mv_fill_sg() rewrite, to fix a data corruption problem
related to IOMMU virtual merging, forgot to account for the
potentially-increased size of the scatter/gather table after its run.

Additionally, the DMA boundary is reduced from 0xffffffff to 0xffff
to more closely match the needs of mv_fill_sg().
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The PCI controller IO base was not set in the au1000 pci code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch fixes a wrong ifdef in the board setup code, leading to the GPIO
pin not being pulled high, and thus the USB switch not being powered at all.

This finishes the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which
started in 2005 (before 2.6.12-rc2), then probably because things were
working anyway for most people got forgotten.

[Ralf: Paolo's original patch didn't fix the module case, Florian's patch
only fixed MTX1 etc. so this is a combined patch plus some cleanups.]

Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Giuseppe Sacco <eppesuig@debian.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

When building a custom keymap, after setting GENERATE_KEYMAP := 1 in
drivers/char/Makefile, the kernel build fails like this:

    CC      drivers/char/vt.o
  make[2]: *** No rule to make target `drivers/char/%.map', needed by `drivers/char/defkeymap.c'.  Stop.
  make[1]: *** [drivers/char] Error 2
  make: *** [drivers] Error 2

This was caused by commit af8b1287, which
deleted a necessary colon from the Makefile rule that generates the keymap,
since that rule contains both a target and a target-pattern.  The following
patch puts the colon back:
Signed-off-by: Maarten Bressers <mbres@gentoo.org>
Cc: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix against access random data bytes outside the dev->chanmap array.
Thanks to Oliver Neukum for pointing me to this issue.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPv6]: Fix ICMPv6 redirect handling with target multicast address
  [PKT_SCHED] cls_u32: error code isn't been propogated properly
  [ROSE]: Fix rose.ko oops on unload
  [TCP]: Fix fastpath_cnt_hint when GSO skb is partially ACKed

When IOCB_FLAG_RESFD flag is set and iocb->aio_resfd is incorrect,
statement 'goto out_put_req' is executed. At label 'out_put_req',
aio_put_req(..) is called, which requires 'req->ki_filp' set.

Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Cc: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

find_lock_page increases page's usage count, we should decrease it
before return VM_FAULT_SIGBUS

Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The test for VM_CAN_NONLINEAR always fails

Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

All the current page_mkwrite() implementations also set the page dirty. Which
results in the set_page_dirty_balance() call to _not_ call balance, because the
page is already found dirty.

This allows us to dirty a _lot_ of pages without ever hitting
balance_dirty_pages().  Not good (tm).

Force a balance call if ->page_mkwrite() was successful.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When the ICMPv6 Target address is multicast, Linux processes the 
redirect instead of dropping it.  The problem is in this code in 
ndisc_redirect_rcv():

         if (ipv6_addr_equal(dest, target)) {
                 on_link = 1;
         } else if (!(ipv6_addr_type(target) & IPV6_ADDR_LINKLOCAL)) {
                 ND_PRINTK2(KERN_WARNING
                            "ICMPv6 Redirect: target address is not 
link-local.\n");
                 return;
         }

This second check will succeed if the Target address is, for example, 
FF02::1 because it has link-local scope.  Instead, it should be checking 
if it's a unicast link-local address, as stated in RFC 2461/4861 Section 
8.1:

       - The ICMP Target Address is either a link-local address (when
         redirected to a router) or the same as the ICMP Destination
         Address (when redirected to the on-link destination).

I know this doesn't explicitly say unicast link-local address, but it's 
implied.

This bug is preventing Linux kernels from achieving IPv6 Logo Phase II 
certification because of a recent error that was found in the TAHI test 
suite - Neighbor Disovery suite test 206 (v6LC.2.3.6_G) had the 
multicast address in the Destination field instead of Target field, so 
we were passing the test.  This won't be the case anymore.

The patch below fixes this problem, and also fixes ndisc_send_redirect() 
to not send an invalid redirect with a multicast address in the Target 
field.  I re-ran the TAHI Neighbor Discovery section to make sure Linux 
passes all 245 tests now.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit a3d38402 aka
"[AX.25]: Fix unchecked rose_add_loopback_neigh uses"
transformed rose_loopback_neigh var into statically allocated one.
However, on unload it will be kfree's which can't work.

Steps to reproduce:

	modprobe rose
	rmmod rose

BUG: unable to handle kernel NULL pointer dereference at virtual address 00000008
 printing eip:
c014c664
*pde = 00000000
Oops: 0000 [#1]
PREEMPT DEBUG_PAGEALLOC
Modules linked in: rose ax25 fan ufs loop usbhid rtc snd_intel8x0 snd_ac97_codec ehci_hcd ac97_bus uhci_hcd thermal usbcore button processor evdev sr_mod cdrom
CPU:    0
EIP:    0060:[<c014c664>]    Not tainted VLI
EFLAGS: 00210086   (2.6.23-rc9 #3)
EIP is at kfree+0x48/0xa1
eax: 00000556   ebx: c1734aa0   ecx: f6a5e000   edx: f7082000
esi: 00000000   edi: f9a55d20   ebp: 00200287   esp: f6a5ef28
ds: 007b   es: 007b   fs: 0000  gs: 0033  ss: 0068
Process rmmod (pid: 1823, ti=f6a5e000 task=f7082000 task.ti=f6a5e000)
Stack: f9a55d20 f9a5200c 00000000 00000000 00000000 f6a5e000 f9a5200c f9a55a00 
       00000000 bf818cf0 f9a51f3f f9a55a00 00000000 c0132c60 65736f72 00000000 
       f69f9630 f69f9528 c014244a f6a4e900 00200246 f7082000 c01025e6 00000000 
Call Trace:
 [<f9a5200c>] rose_rt_free+0x1d/0x49 [rose]
 [<f9a5200c>] rose_rt_free+0x1d/0x49 [rose]
 [<f9a51f3f>] rose_exit+0x4c/0xd5 [rose]
 [<c0132c60>] sys_delete_module+0x15e/0x186
 [<c014244a>] remove_vma+0x40/0x45
 [<c01025e6>] sysenter_past_esp+0x8f/0x99
 [<c012bacf>] trace_hardirqs_on+0x118/0x13b
 [<c01025b6>] sysenter_past_esp+0x5f/0x99
 =======================
Code: 05 03 1d 80 db 5b c0 8b 03 25 00 40 02 00 3d 00 40 02 00 75 03 8b 5b 0c 8b 73 10 8b 44 24 18 89 44 24 04 9c 5d fa e8 77 df fd ff <8b> 56 08 89 f8 e8 84 f4 fd ff e8 bd 32 06 00 3b 5c 86 60 75 0f 
EIP: [<c014c664>] kfree+0x48/0xa1 SS:ESP 0068:f6a5ef28
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When only GSO skb was partially ACKed, no hints are reset,
therefore fastpath_cnt_hint must be tweaked too or else it can
corrupt fackets_out. The corruption to occur, one must have
non-trivial ACK/SACK sequence, so this bug is not very often
that harmful. There's a fackets_out state reset in TCP because
fackets_out is known to be inaccurate and that fixes the issue
eventually anyway.

In case there was also at least one skb that got fully ACKed,
the fastpath_skb_hint is set to NULL which causes a recount for
fastpath_cnt_hint (the old value won't be accessed anymore),
thus it can safely be decremented without additional checking.

Reported by Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should only reparent to a class former class devices that
form the base of class hierarchy. Nested devices should still
grow from their real parents.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: point to migration document

Add the manufacturer and card id of teltonica pcmcia modems to serial_cs.c
Signed-off-by: Attila Kinali <attila@kinali.ch>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Document sequence of keypresses that actually works. Yes, this changed
year-or-so ago.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Async signals should not be reported as sent by current in audit log.  As
it is, we call audit_signal_info() too early in check_kill_permission().
Note that check_kill_permission() has that test already - it needs to know
if it should apply current-based permission checks.  So the solution is to
move the call of audit_signal_info() between those.

Bogosity in question is easily reproduced - add a rule watching for e.g.
kill(2) from specific process (so that audit_signal_info() would not
short-circuit to nothing), say load_policy, watch the bogus OBJ_PID entry
in audit logs claiming that write(2) on selinuxfs file issued by
load_policy(8) had somehow managed to send a signal to syslogd...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Steve Grubb <sgrubb@redhat.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Modulat lguest started giving linking errors

MODPOST 1 modules
ERROR: "kasprintf" [drivers/lguest/lg.ko] undefined!
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Provide some documentation for CONFIG_LOCK_STAT.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

VIA C3 Ezra-T has RevisionID equal to 1, but it needs RevisionKey to be 0
or CPU will ignore new frequency and will continue to work at old
frequency.  New "revid_errata" option will force RevisionKey to be set to
0, whatever RevisionID is.

Additionaly "Longhaul" will not silently ignore unsuccessful transition.
It will try to check if "revid_errata" or "disable_acpi_c3" options need to
be enabled for this processor/system.

Same for Longhaul ver.  2 support.  It will be disabled if none of above
options will work.

 Best case scenario (with patch apllied and v2 enabled):
 longhaul: VIA C3 'Ezra' [C5C] CPU detected.  Longhaul v2 supported.
 longhaul: Using northbridge support.
 longhaul: VRM 8.5
 longhaul: Max VID=1.350  Min VID=1.050, 13 possible voltage scales
 longhaul: f: 300000 kHz, index: 0, vid: 1050 mV
 [...]
 longhaul: Voltage scaling enabled.
 Worst case scenario:
 longhaul: VIA C3 'Ezra-T' [C5M] CPU detected.  Powersaver supported.
 longhaul: Using northbridge support.
 longhaul: Using ACPI support.
 longhaul: VRM 8.5
 longhaul: Claims to support voltage scaling but min & max are both 1.250. Voltage scaling disabled
 longhaul: Failed to set requested frequency!
 longhaul: Enabling "Ignore Revision ID" option.
 longhaul: Failed to set requested frequency!
 longhaul: Disabling ACPI C3 support.
 longhaul: Disabling "Ignore Revision ID" option.
 longhaul: Failed to set requested frequency!
 longhaul: Enabling "Ignore Revision ID" option.

[akpm@linux-foundation.org: coding-style cleanups]
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When using /proc/timer_stats on ppc64 I noticed the events/sec field wasnt
accurate.  Sometimes the integer part was incorrect due to rounding (we
werent taking the fractional seconds into consideration).

The fraction part is also wrong, we need to pad the printf statement and
take the bottom three digits of 1000 times the value.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It turns out that there are a few other five-second timers in the
kernel, and if the timers get in sync, the load-average can get
artificially inflated by events that just happen to coincide.

So just offset the load average calculation it by a timer tick.

Noticed by Anders Boström, for whom the coincidence started triggering
on one of his machines with the JBD jiffies rounding code (JBD is one of
the subsystems that also end up using a 5-second timer by default).
Tested-by: Anders Boström <anders@bostrom.dyndns.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We should generally prefer to return ERESTARTNOHAND rather than EINTR,
so that processes with unhandled signals that get ignored don't return
EINTR.

This can help with X startup issues:

    Fatal server error:
    xf86OpenConsole: VT_WAITACTIVE failed: Interrupted system call

although the real fix is having the X server always retry EINTR
regardless (since EINTR does happen for signals that have handlers
installed). Keithp has a patch for that.

Regardless, ERESTARTNOHAND is the correct thing to use.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] IP32: Enable PCI bridges