- 23 Jul, 2020 10 commits
-
-
Yuchung Cheng authored
Previously TLP may send multiple probes of new data in one flight. This happens when the sender is cwnd limited. After the initial TLP containing new data is sent, the sender receives another ACK that acks partial inflight. It may re-arm another TLP timer to send more, if no further ACK returns before the next TLP timeout (PTO) expires. The sender may send in theory a large amount of TLP until send queue is depleted. This only happens if the sender sees such irregular uncommon ACK pattern. But it is generally undesirable behavior during congestion especially. The original TLP design restrict only one TLP probe per inflight as published in "Reducing Web Latency: the Virtue of Gentle Aggression", SIGCOMM 2013. This patch changes TLP to send at most one probe per inflight. Note that if the sender is app-limited, TLP retransmits old data and did not have this issue. Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dan Carpenter authored
We recently added some bounds checking in ax25_connect() and ax25_sendmsg() and we so we removed the AX25_MAX_DIGIS checks because they were no longer required. Unfortunately, I believe they are required to prevent integer overflows so I have added them back. Fixes: 8885bb06 ("AX.25: Prevent out-of-bounds read in ax25_sendmsg()") Fixes: 2f2a7ffa ("AX.25: Fix out-of-bounds read in ax25_connect()") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Navid Emamdoost authored
In the implementation of uld_send(), the skb is consumed on all execution paths except one. Release skb when returning NET_XMIT_DROP. Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by:
-
Egor Pomozov authored
This patch fixes PTP on AQC10X. PTP support on AQC10X requires FW involvement and FW configures the TPS data arb mode itself. So we must make sure driver doesn't touch TPS data arb mode on AQC10x if PTP is enabled. Otherwise, there are no timestamps even though packets are flowing. Fixes: 2deac71a ("net: atlantic: QoS implementation: min_rate") Signed-off-by:
Egor Pomozov <epomozov@marvell.com> Signed-off-by:
Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by:
Igor Russkikh <irusskikh@marvell.com> Signed-off-by:
-
Peilin Ye authored
Checks on `addr_len` and `usax->sax25_ndigis` are insufficient. ax25_sendmsg() can go out of bounds when `usax->sax25_ndigis` equals to 7 or 8. Fix it. It is safe to remove `usax->sax25_ndigis > AX25_MAX_DIGIS`, since `addr_len` is guaranteed to be less than or equal to `sizeof(struct full_sockaddr_ax25)` Signed-off-by:
Peilin Ye <yepeilin.cs@gmail.com> Signed-off-by:
-
David S. Miller authored
Xin Long says: ==================== sctp: shrink stream outq in the right place Patch 1 is an improvement, and Patch 2 is a bug fix. ==================== Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Xin Long authored
When adding a stream with stream reconf, the new stream firstly is in CLOSED state but new out chunks can still be enqueued. Then once gets the confirmation from the peer, the state will change to OPEN. However, if the peer denies, it needs to roll back the stream. But when doing that, it only sets the stream outcnt back, and the chunks already in the new stream don't get purged. It caused these chunks can still be dequeued in sctp_outq_dequeue_data(). As its stream is still in CLOSE, the chunk will be enqueued to the head again by sctp_outq_head_data(). This chunk will never be sent out, and the chunks after it can never be dequeued. The assoc will be 'hung' in a dead loop of sending this chunk. To fix it, this patch is to purge these chunks already in the new stream by calling sctp_stream_shrink_out() when failing to do the addstream reconf. Fixes: 11ae76e6 ("sctp: implement receiver-side procedures for the Reconf Response Parameter") Reported-by:
Ying Xu <yinxu@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Xin Long authored
It's not necessary to go list_for_each for outq->out_chunk_list when new outcnt >= old outcnt, as no chunk with higher sid than new (outcnt - 1) exists in the outqueue. While at it, also move the list_for_each code in a new function sctp_stream_shrink_out(), which will be used in the next patch. Signed-off-by:
-
Peilin Ye authored
Checks on `addr_len` and `fsa->fsa_ax25.sax25_ndigis` are insufficient. ax25_connect() can go out of bounds when `fsa->fsa_ax25.sax25_ndigis` equals to 7 or 8. Fix it. This issue has been reported as a KMSAN uninit-value bug, because in such a case, ax25_connect() reaches into the uninitialized portion of the `struct sockaddr_storage` statically allocated in __sys_connect(). It is safe to remove `fsa->fsa_ax25.sax25_ndigis > AX25_MAX_DIGIS` because `addr_len` is guaranteed to be less than or equal to `sizeof(struct full_sockaddr_ax25)`. Reported-by: syzbot+c82752228ed975b0a623@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?id=55ef9d629f3b3d7d70b69558015b63b48d01af66Signed-off-by:
-
Claudiu Manoil authored
For ENETC ports that register an external MDIO bus, the bus doesn't get removed on the error bailout path of enetc_pf_probe(). This issue became much more visible after recent: commit 07095c02 ("net: enetc: Use DT protocol information to set up the ports") Before this commit, one could make probing fail on the error path only by having register_netdev() fail, which is unlikely. But after this commit, because it moved the enetc_of_phy_get() call up in the probing sequence, now we can trigger an mdiobus_free() bug just by forcing enetc_alloc_msix() to return error, i.e. with the 'pci=nomsi' kernel bootarg (since ENETC relies on MSI support to work), as the calltrace below shows: kernel BUG at /home/eiz/work/enetc/net/drivers/net/phy/mdio_bus.c:648! Internal error: Oops - BUG: 0 [#1] PREEMPT SMP [...] Hardware name: LS1028A RDB Board (DT) pstate: 80000005 (Nzcv daif -PAN -UAO BTYPE=--) pc : mdiobus_free+0x50/0x58 lr : devm_mdiobus_free+0x14/0x20 [...] Call trace: mdiobus_free+0x50/0x58 devm_mdiobus_free+0x14/0x20 release_nodes+0x138/0x228 devres_release_all+0x38/0x60 really_probe+0x1c8/0x368 driver_probe_device+0x5c/0xc0 device_driver_attach+0x74/0x80 __driver_attach+0x8c/0xd8 bus_for_each_dev+0x7c/0xd8 driver_attach+0x24/0x30 bus_add_driver+0x154/0x200 driver_register+0x64/0x120 __pci_register_driver+0x44/0x50 enetc_pf_driver_init+0x24/0x30 do_one_initcall+0x60/0x1c0 kernel_init_freeable+0x1fc/0x274 kernel_init+0x14/0x110 ret_from_fork+0x10/0x34 Fixes: ebfcb23d ("enetc: Add ENETC PF level external MDIO support") Signed-off-by:
Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by:
-
- 22 Jul, 2020 3 commits
-
-
Murali Karicheri authored
Currently drive supports taprio offload which is a tc feature offloaded to cpsw hardware. So driver has to set the hw feature flag, NETIF_F_HW_TC in the net device to be compliant. This patch adds the flag. Fixes: 8127224c ("ethernet: ti: am65-cpsw-qos: add TAPRIO offload support") Signed-off-by:
Murali Karicheri <m-karicheri2@ti.com> Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
-
Wang Hai authored
When regmap_update_bits failed in ave_init(), calls of the functions reset_control_assert() and clk_disable_unprepare() were missed. Add goto out_reset_assert to do this. Fixes: 57878f2f ("net: ethernet: ave: add support for phy-mode setting of system controller") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Wang Hai <wanghai38@huawei.com> Reviewed-by:
Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by:
-
Xie He authored
This driver is not working because of problems of its receiving code. This patch fixes it to make it work. When the driver receives an LAPB frame, it should first pass the frame to the LAPB module to process. After processing, the LAPB module passes the data (the packet) back to the driver, the driver should then add a one-byte pseudo header and pass the data to upper layers. The changes to the "x25_asy_bump" function and the "x25_asy_data_indication" function are to correctly implement this procedure. Also, the "x25_asy_unesc" function ignores any frame that is shorter than 3 bytes. However the shortest frames are 2-byte long. So we need to change it to allow 2-byte frames to pass. Cc: Eric Dumazet <edumazet@google.com> Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by:
Xie He <xie.he.0141@gmail.com> Reviewed-by:
Martin Schiller <ms@dev.tdt.de> Signed-off-by:
-
- 21 Jul, 2020 27 commits
-
-
Paolo Pisati authored
According to 'man 8 ip-netns', if `ip netns identify` returns an empty string, there's no net namespace associated with current PID: fix the net ns entrance logic. Signed-off-by:
Paolo Pisati <paolo.pisati@canonical.com> Acked-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
David S. Miller authored
Alexander Lobakin says: ==================== qed: suppress irrelevant error messages on HW init This raises the verbosity level of several error/warning messages on driver/module initialization, most of which are false-positives, and the one actively spamming the log for no reason. ==================== Signed-off-by: -
Alexander Lobakin authored
It was found that qed_pglueb_rbc_attn_handler() can produce a lot of false-positive error detections on driver load/reload (especially after crashes/recoveries) and spam the kernel log: [ 4.958275] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d00ff0 [ 2079.146764] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0 [ 2116.374631] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0 [ 2135.250564] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0 [...] Reduce the logging level of two false-positive prone error messages from notice to verbose on initialization (only) to not mix it with real error attentions while debugging. Fixes: 666db486 ("qed: Revise load sequence to avoid PCI errors") Signed-off-by:
Alexander Lobakin <alobakin@marvell.com> Signed-off-by:
Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by:
-
Alexander Lobakin authored
Change the verbosity of the "don't support RoCE & iWARP simultaneously" warning to debug level to stop flooding on driver/hardware initialization: [ 4.783230] qede 01:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0 [MBI 15.10.6] [eth0] [ 4.810020] [qed_rdma_set_pf_params:2076()]Current day drivers don't support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only [ 4.861186] qede 01:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0 [MBI 15.10.6] [eth1] [ 4.893311] [qed_rdma_set_pf_params:2076()]Current day drivers don't support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only [ 5.181713] qede a1:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0 [MBI 15.10.6] [eth2] [ 5.224740] [qed_rdma_set_pf_params:2076()]Current day drivers don't support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only [ 5.276449] qede a1:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0 [MBI 15.10.6] [eth3] [ 5.318671] [qed_rdma_set_pf_params:2076()]Current day drivers don't support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only [ 5.369548] qede a1:00.02: Storm FW 8.37.7.0, Management FW 8.52.9.0 [MBI 15.10.6] [eth4] [ 5.411645] [qed_rdma_set_pf_params:2076()]Current day drivers don't support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only Fixes: e0a8f9de ("qed: Add iWARP enablement support") Signed-off-by:
-
Taehee Yoo authored
In the nsim_create(), rtnl_lock() is called before nsim_bpf_init(). If nsim_bpf_init() is failed, rtnl_unlock() should be called, but it isn't called. So, unbalanced locking would occur. Fixes: e05b2d14 ("netdevsim: move netdev creation/destruction to dev probe") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Reviewed-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
-
Helmut Grohne authored
When doing "ip link set dev ... up" for a ksz9477 backed link, ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove 1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is called. Doing so reverts any previous change to advertised link modes e.g. using a udevd .link file. phy_remove_link_mode is not meant to be used while opening a link and should be called during phy probe when the link is not yet available to userspace. Therefore move the phy_remove_link_mode calls into ksz9477_switch_register. It indirectly calls dsa_register_switch, which creates the relevant struct phy_devices and we update the link modes right after that. At that time dev->features is already initialized by ksz9477_switch_detect. Remove phy_setup from ksz_dev_ops as no users remain. Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/ Fixes: 42fc6a4c ("net: dsa: microchip: prepare PHY for proper advertisement") Signed-off-by:
Helmut Grohne <helmut.grohne@intenta.de> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
David S. Miller authored
Huazhong Tan says: ==================== net: hns3: fixes for -net There are some bugfixes for the HNS3 ethernet driver. ==================== Signed-off-by: -
Jian Shen authored
Currently, PF queries the MAC link status per second by calling function hclge_get_mac_link_status(). It return the error code when failed to send cmdq command to firmware. It's incorrect, because this return value is used as the MAC link status, which 0 means link down, and none-zero means link up. So fixes it. Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
Huazhong tan <tanhuazhong@huawei.com> Signed-off-by:
-
Yunsheng Lin authored
The content of the TX desc is automatically cleared by the HW when the HW has sent out the packet to the wire. When desc filling fails in hns3_nic_net_xmit(), it will call hns3_clear_desc() to do the error handling, which miss zeroing of the TX desc and the checking if a unmapping is needed. So add the zeroing and checking in hns3_clear_desc() to avoid the above problem. Also add DESC_TYPE_UNKNOWN to indicate the info in desc_cb is not valid, because hns3_nic_reclaim_desc() may treat the desc_cb->type of zero as packet and add to the sent pkt statistics accordingly. Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by:
Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by:
-
Yunsheng Lin authored
With GRO and fraglist support, the SKB can be aggregated to a total size of 65535, and when that SKB is forwarded through a bridge, the size of the SKB may be pushed to exceed the size of 65535 when br_dev_queue_push_xmit() is called. The max send size of BD supported by the HW is 65535, when a SKB with a headlen of over 65535 is sent to the driver, the driver needs to use multi BD to send the linear data, and the send size of the last BD is calculated incorrectly by the driver who is using '&' operation, which causes a TX error. Use '%' operation to fix this problem. Fixes: 3fe13ed9 ("net: hns3: avoid mult + div op in critical data path") Signed-off-by:
-
Yunsheng Lin authored
When a big TX buffer is sent using multi BD, the driver maps the whole TX buffer, and unmaps it using info in desc_cb corresponding to each BD, but only the info in the desc_cb of first BD is correct, other info in desc_cb is wrong, which causes TX unmapping problem when SMMU is on. Only set the mapping and freeing info in the desc_cb of first BD to fix this problem, because the TX buffer only need to be unmapped and freed once. Fixes: 1e8a7977("net: hns3: add handling for big TX fragment") Signed-off-by:
-
Miaohe Lin authored
We can't use IS_UDPLITE to replace udp_sk->pcflag when UDPLITE_RECV_CC is checked. Fixes: b2bf1e26 ("[UDP]: Clean up for IS_UDPLITE macro") Signed-off-by:
Miaohe Lin <linmiaohe@huawei.com> Signed-off-by:
-
Xiongfeng Wang authored
When I cat 'tx_timeout' by sysfs, it displays as follows. It's better to add a newline for easy reading. root@syzkaller:~# cat /sys/devices/virtual/net/lo/queues/tx-0/tx_timeout 0root@syzkaller:~# Signed-off-by:
Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by:
-
Yoshihiro Shimoda authored
According to the report of [1], this driver is possible to cause the following error in ravb_tx_timeout_work(). ravb e6800000.ethernet ethernet: failed to switch device to config mode This error means that the hardware could not change the state from "Operation" to "Configuration" while some tx and/or rx queue are operating. After that, ravb_config() in ravb_dmac_init() will fail, and then any descriptors will be not allocaled anymore so that NULL pointer dereference happens after that on ravb_start_xmit(). To fix the issue, the ravb_tx_timeout_work() should check the return values of ravb_stop_dma() and ravb_dmac_init(). If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX and just exits. If ravb_dmac_init() fails, just exits. [1] https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/Reported-by:
Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by:
Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by:
-
David S. Miller authored
Kuniyuki Iwashima says: ==================== udp: Fix reuseport selection with connected sockets. This patch set addresses two issues which happen when both connected and unconnected sockets are in the same UDP reuseport group. ==================== Signed-off-by: -
Kuniyuki Iwashima authored
Currently, SO_REUSEPORT does not work well if connected sockets are in a UDP reuseport group. Then reuseport_has_conns() returns true and the result of reuseport_select_sock() is discarded. Also, unconnected sockets have the same score, hence only does the first unconnected socket in udp_hslot always receive all packets sent to unconnected sockets. So, the result of reuseport_select_sock() should be used for load balancing. The noteworthy point is that the unconnected sockets placed after connected sockets in sock_reuseport.socks will receive more packets than others because of the algorithm in reuseport_select_sock(). index | connected | reciprocal_scale | result --------------------------------------------- 0 | no | 20% | 40% 1 | no | 20% | 20% 2 | yes | 20% | 0% 3 | no | 20% | 40% 4 | yes | 20% | 0% If most of the sockets are connected, this can be a problem, but it still works better than now. Fixes: acdcecc6 ("udp: correct reuseport selection with connected sockets") CC: Willem de Bruijn <willemb@google.com> Reviewed-by:Benjamin Herrenschmidt <benh@amazon.com> Signed-off-by:
Kuniyuki Iwashima <kuniyu@amazon.co.jp> Acked-by:
-
Kuniyuki Iwashima authored
If an unconnected socket in a UDP reuseport group connect()s, has_conns is set to 1. Then, when a packet is received, udp[46]_lib_lookup2() scans all sockets in udp_hslot looking for the connected socket with the highest score. However, when the number of sockets bound to the port exceeds max_socks, reuseport_grow() resets has_conns to 0. It can cause udp[46]_lib_lookup2() to return without scanning all sockets, resulting in that packets sent to connected sockets may be distributed to unconnected sockets. Therefore, reuseport_grow() should copy has_conns. Fixes: acdcecc6 ("udp: correct reuseport selection with connected sockets") CC: Willem de Bruijn <willemb@google.com> Reviewed-by:
-
Tung Nguyen authored
Commit 02288248 ("tipc: eliminate gap indicator from ACK messages") eliminated sending of the 'gap' indicator in regular ACK messages and only allowed to build NACK message with enabled probe/probe_reply. However, necessary correction for building NACK message was missed in tipc_link_timeout() function. This leads to significant delay and link reset (due to retransmission failure) in lossy environment. This commit fixes it by setting the 'probe' flag to 'true' when the receive deferred queue is not empty. As a result, NACK message will be built to send back to another peer. Fixes: 02288248 ("tipc: eliminate gap indicator from ACK messages") Acked-by:
Jon Maloy <jmaloy@redhat.com> Signed-off-by:
Tung Nguyen <tung.q.nguyen@dektech.com.au> Signed-off-by:
-
Bixuan Cui authored
Fix the warning: [-Werror=-Wframe-larger-than=] drivers/net/ethernet/neterion/vxge/vxge-main.c: In function'VXGE_COMPLETE_VPATH_TX.isra.37': drivers/net/ethernet/neterion/vxge/vxge-main.c:119:1: warning: the frame size of 1056 bytes is larger than 1024 bytes Dropping the NR_SKB_COMPLETED to 16 is appropriate that won't have much impact on performance and functionality. Signed-off-by:
Bixuan Cui <cuibixuan@huawei.com> Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
Huang Guobin authored
The ag71xx_mdio_probe() forgets to call clk_disable_unprepare() when of_reset_control_get_exclusive() failed. Add the missed call to fix it. Fixes: d51b6ce4 ("net: ethernet: add ag71xx driver") Reported-by:
Huang Guobin <huangguobin4@huawei.com> Signed-off-by:
-
wenxu authored
The fragment packets do defrag in tcf_ct_handle_fragments will clear the skb->cb which make the qdisc_skb_cb clear too. So the qdsic_skb_cb should be store before defrag and restore after that. It also update the pkt_len after all the fragments finish the defrag to one packet and make the following actions counter correct. Fixes: b57dc7c1 ("net/sched: Introduce action ct") Signed-off-by:
wenxu <wenxu@ucloud.cn> Signed-off-by:
-
Navid Emamdoost authored
The implementation of s3fwrn5_recv_frame() is supposed to consume skb on all execution paths. Release skb before returning -ENODEV. Signed-off-by:
-
Vinay Kumar Yadav authored
ip_dev_find() call holds net_device reference which is not needed, use __ip_dev_find() which does not hold reference. v1->v2: - Correct submission tree. - Add fixes tag. Fixes: cc35c88a ("crypto : chtls - CPL handler definition") Signed-off-by:
Vinay Kumar Yadav <vinay.yadav@chelsio.com> Signed-off-by:
-
Vinay Kumar Yadav authored
When tls data skb is pending for Tx and tls alert comes , It is wrongly overwrite the record type of tls data to tls alert record type. fix the issue correcting it. v1->v2: - Correct submission tree. - Add fixes tag. Fixes: 6919a826 ("Crypto/chtls: add/delete TLS header in driver") Signed-off-by:
-
David S. Miller authored
Shannon Nelson says: ==================== ionic: locking and filter fixes These patches address an ethtool show regs problem, some locking sightings, and issues with RSS hash and filter_id tracking after a managed FW update. ==================== Signed-off-by: -
Shannon Nelson authored
The ionic_wait_on_bit_lock() was a open-coded mutex knock-off used only for protecting the queue reset operations, and there was no reason not to use the real thing. We can use the lock more correctly and to better protect the queue stop and start operations from cross threading. We can also remove a useless and expensive bit operation from the Rx path. This fixes a case found where the link_status_check from a link flap could run into an MTU change and cause a crash. Fixes: beead698 ("ionic: Add the basic NDO callbacks for netdev support") Signed-off-by:
Shannon Nelson <snelson@pensando.io> Signed-off-by:
-
Shannon Nelson authored
Make sure the RSS hash key is kept across a fw update by not de-initing it when an update is happening. Fixes: c672412f ("ionic: remove lifs on fw reset") Signed-off-by:
-
