This patch add police action to set flow meter table which is defined
in IEEE802.1Qci. Flow metering is two rates two buckets and three color
marker to policing the frames, we only enable one rate one bucket in
this patch.

Flow metering shares a same policer pool with VCAP policers, so the PSFP
policer calls ocelot_vcap_policer_add() and ocelot_vcap_policer_del() to
set flow meter police.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Policer was previously automatically assigned from the highest index to
the lowest index from policer pool. But police action of tc flower now
uses index to set an police entry. This patch uses the police index to
set vcap policers, so that one policer can be shared by multiple rules.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds stream gate settings for PSFP. Use SGI table to store
stream gate entries. Disable the gate entry when it is not used by any
stream.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VSC9959 supports Per-Stream Filtering and Policing(PSFP) that complies
with the IEEE 802.1Qci standard. The stream is identified by Null stream
identification(DMAC and VLAN ID) defined in IEEE802.1CB.

For PSFP, four tables need to be set up: stream table, stream filter
table, stream gate table, and flow meter table. Identify the stream by
parsing the tc flower keys and add it to the stream table. The stream
filter table is automatically maintained, and its index is determined by
SGID(flow gate index) and FMID(flow meter index).
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PSFP support gate and police action. This patch add the gate and police
action to flower parse action, check chain ID to determine which block
to offload. Adding psfp callback functions to add, delete and update gate
and police in PSFP table if hardware supports it.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some chips in the ocelot series such as VSC9959 support Per-Stream
Filtering and Policing(PSFP), which is processing after VCAP blocks.
We set this block on chain 30000 and set vcap IS2 chain to goto PSFP
chain if hardware support.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ocelot_mact_learn_streamdata() can be used in VSC9959 to overwrite an
FDB entry with stream data. The stream data includes SFID and SSID which
can be used for PSFP and FRER set.

ocelot_mact_lookup() can be used to check if the given {DMAC, VID} FDB
entry is exist, and also can retrieve the DEST_IDX and entry type for
the FDB entry.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In 99ce45d5, we moved a route refcount decrement from
mctp_do_fragment_route into the caller. This invalidates the assumption
that the route test makes about refcount behaviour, so the route tests
fail.

This change fixes the test case to suit the new refcount behaviour.

Fixes: 99ce45d5 ("mctp: Implement extended addressing")
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yao Jing <yao.jing2@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing entries to fix these "make htmldocs" warnings.

./include/linux/skbuff.h:953: warning: Function parameter or member 'll_node' not described in 'sk_buff'
./include/net/sock.h:540: warning: Function parameter or member 'defer_list' not described in 'sock'

Fixes: f35f8219 ("tcp: defer skb freeing after socket lock is released")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
10GbE Intel Wired LAN Driver Updates 2021-11-17

Radoslaw Tyl says:

The change is a consequence of errors reported by the ixgbevf driver
while starting several virtual guests at the same time on ESX host.
During this, VF was not able to communicate correctly with the PF,
as a result reported "PF still in reset state. Is the PF interface up?"
and then goes to locked state. The only thing left was to reload
the VF driver on the guest OS.

The background of the problem is that the current PFU and VFU
semaphore locking mechanism between sender and receiver may cause
overriding Mailbox memory (VFMBMEM), in such scenario receiver of
the original message will read the invalid, corrupted or one (or more)
message may be lost.

This change is actually as a support for communication with PF ESX
driver and does not contains changes and support for ixgbe driver.
For maintain backward compatibility, previous communication method
has been preserved in the form of LEGACY functions.

In the future there is a plan to add a support for a 1.5 mailbox API
communication also to ixgbe driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Killing the kernel because a certain MDIO bus object is not in the
desired state at various points in the registration or unregistration
paths is excessive and is not helping in troubleshooting or fixing
issues. Replace the BUG_ON() with WARN() and print out the MDIO bus name
to facilitate debugging.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: dpaa2: phylink validate implementation updates

This series converts dpaa2 to fill in the supported_interfaces member
of phylink_config, cleans up the validate() implementation, and then
converts to phylink_generic_validate(). Previous behaviour should be
preserved.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

DPAA2 has no special behaviour in its validation implementation, so can
be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode, nor handle
PHY_INTERFACE_MODE_NA in the validation function. Remove these to
simplify the implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Populate the phy interface mode bitmap for the Freescale DPAA2 driver
with interfaces modes supported by the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: ag71xx: phylink validate implementation updates

This series converts ag71xx to fill in the supported_interfaces member
of phylink_config, cleans up the validate() implementation, and then
converts to phylink_generic_validate().

The question over the port linkmode restriction has been answered by
Oleksij - there is no reason for this restriction, so we can go the
whole hog with this conversion. Thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ag71xx apparently only supports MII port type, which makes it different
from other implementations. However, Oleksij says there is no special
reason for this.

Convert the driver to use phylink_generic_validate(), which will allow
all ethtool port linkmodes instead of only MII, giving the driver
consistent behaviour with other drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode, nor handle
PHY_INTERFACE_MODE_NA in the validation function. Remove these to
simplify the implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Populate the phy_interface_t bitmap for the Atheros ag71xx driver with
interfaces modes supported by the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split clocks settings from init callback into clks_config callback,
which could support platform level clock management.

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to inet v4 raw sockets for binding to nonlocal addresses
through the IP_FREEBIND and IP_TRANSPARENT socket options, as well as
the ipv4.ip_nonlocal_bind kernel parameter.

Add helper function to inet_sock.h to check for bind address validity on
the base of the address type and whether nonlocal address are enabled
for the socket via any of the sockopts/sysctl, deduplicating checks in
ipv4/ping.c, ipv4/af_inet.c, ipv6/af_inet6.c (for mapped v4->v6
addresses), and ipv4/raw.c.

Add test cases with IP[V6]_FREEBIND verifying that both v4 and v6 raw
sockets support binding to nonlocal addresses after the change. Add
necessary support for the test cases to nettest.
Signed-off-by: Riccardo Paolo Bestetti <pbl@bestov.io>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211117090010.125393-1-pbl@bestov.ioSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This is needed for some arches, as reported by Geert Uytterhoeven,
Randy Dunlap and Stephen Rothwell

Fixes: 4721031c ("net: move gro definitions to include/net/gro.h")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211117100130.2368319-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

txq_trans_cond_update() takes netdev_tx_queue *nq,
not nq->trans_start.

Fixes: 5337824f ("net: annotate accesses to queue->trans_start")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20211117152917.3739-1-alexandr.lobakin@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Provide improved mailbox communication, between PF and VF,
which is defined as API version 1.5.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Improve reliability of the mailbox communication and remove
its potential flaws that may lead to the undefined or faulty behavior.

Recently some users reported issues on ESX with 10G Intel NICs which were
found to be caused by incorrect implementation of the PF-VF mailbox
communication.

Technical investigation highlighted areas to improve in the communication
between PF or VF that wants to send the message (sender) and the other
part which receives the message (receiver):

 - Locking the mailbox when the sender wants to send a message
 - Releasing the mailbox when the communication ends
 - Returning the result of the mailbox message execution
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add legacy suffix to mailbox functions which should be backwards compatible
with older PF drivers. Communication during API negotiation always has to
be done using the earlier implementation.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add new handling for error codes:
 IXGBE_ERR_CONFIG - ixgbe_mbx_operations is not correctly set
 IXGBE_ERR_TIMEOUT - mailbox operation, e.g. poll for message, timeout
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

There is name similarity within IXGBE_VT_MSGTYPE_ACK and
PFMAILBOX.ACK / VFMAILBOX.ACK. MSGTYPE macros are renamed to SUCCESS and
FAILURE because they are not specified in datasheet and now will be
easily distinguishable.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Eric Dumazet says:

====================
net: make dev_watchdog() less intrusive

dev_watchdog() is used on many NIC to periodically monitor TX queues
to detect hangs.

Problem is : It stops all queues, then check them, then 'unfreeze' them.

Not only this stops feeding the NIC, it also migrates all qdiscs
to be serviced on the cpu calling netif_tx_unlock(), causing
a potential latency artifact.

With many TX queues, this is becoming more visible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no reason for stopping all TX queues from dev_watchdog()

Not only this stops feeding the NIC, it also migrates all qdiscs
to be serviced on the cpu calling netif_tx_unlock(), causing
a potential latency artifact.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are not fast path, there is no point in inlining them.

Also provide netif_freeze_queues()/netif_unfreeze_queues()
so that we can use them from dev_watchdog() in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In following patches, dev_watchdog() will no longer stop all queues.
It will read queue->trans_start locklessly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tx_timeout_show() assumed dev_watchdog() would stop all
the queues, to fetch queue->trans_timeout under protection
of the queue->_xmit_lock.

As we want to no longer disrupt transmits, we use an
atomic_long_t instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: david decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'for-net-next-2021-11-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Luiz Augusto von Dentz says:

====================
bluetooth-next pull request for net-next:

 - Add support for AOSP Bluetooth Quality Report
 - Enables AOSP extension for Mediatek Chip (MT7921 & MT7922)
 - Rework of HCI command execution serialization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If the used PHYs also support hardware timestamping, all configuration requests
should be forwared to the PHYs instead of being processed by the MAC driver
itself.

This enables PHY timestamping in combination with the cpsw driver.

Tested with an am335x based board with two DP83640 PHYs connected to the cpsw
switch.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update net_failover documentation with missing and incomplete
details to get a proper working setup.
Signed-off-by: Vasudev Kamath <vasudev@copyninja.info>
Reviewed-by: Krishna Kumar <krikku@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: ocelot_net: phylink validate implementation updates

This series converts ocelot_net to fill in the supported_interfaces
member of phylink_config, cleans up the validate() implementation,
and then converts to phylink_generic_validate().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ocelot_net has no special behaviour in its validation implementation, so
can be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>