Intel mGbE variant implemented in EHL and TGL can be set to select
different clock frequency based on GPO bits in MAC_GPIO_STATUS register.

We introduce a new "void (*ptp_clk_freq_config)(void *priv)" in platform
data so that if a platform is required to configure the frequency of clock
source, in this case Intel mGBE does, the platform-specific configuration
of the PTP clock setting is done when stmmac_ptp_register() is called.
Signed-off-by: Wong, Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tobias Waldekranz says:

====================
net: dsa: mv88e6xxx: Offload bridge port flags

Add support for offloading learning and broadcast flooding flags. With
this in place, mv88e6xx supports offloading of all bridge port flags
that are currently supported by the bridge.

Broadcast flooding is somewhat awkward to control as there is no
per-port bit for this like there is for unknown unicast and unknown
multicast. Instead we have to update the ATU entry for the broadcast
address for all currently used FIDs.

v2 -> v3:
  - Only return a netdev from dsa_port_to_bridge_port if the port is
    currently bridged (Vladimir & Florian)

v1 -> v2:
  - Ensure that mv88e6xxx_vtu_get handles VID 0 (Vladimir)
  - Fixed off-by-one in mv88e6xxx_port_set_assoc_vector (Vladimir)
  - Fast age all entries on port when disabling learning (Vladimir)
  - Correctly detect bridge flags on LAG ports (Vladimir)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

These switches have two modes of classifying broadcast:

1. Broadcast is multicast.
2. Broadcast is its own unique thing that is always flooded
   everywhere.

This driver uses the first option, making sure to load the broadcast
address into all active databases. Because of this, we can support
per-port broadcast flooding by (1) making sure to only set the subset
of ports that have it enabled whenever joining a new bridge or VLAN,
and (2) by updating all active databases whenever the setting is
changed on a port.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow a user to control automatic learning per port.

Many chips have an explicit "LearningDisable"-bit that can be used for
this, but we opt for setting/clearing the PAV instead, as it works on
all devices at least as far back as 6083.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In accordance with the comment in dsa_port_bridge_leave, standalone
ports shall be configured to flood all types of traffic. This change
aligns the mv88e6xxx driver with that policy.

Previously a standalone port would initially not egress any unknown
traffic, but after joining and then leaving a bridge, it would.

This does not matter that much since we only ever send FROM_CPUs on
standalone ports, but it seems prudent to make sure that the initial
values match those that are applied after a bridging/unbridging cycle.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the conventional declaration style of a MAC address in the
kernel (u8 addr[ETH_ALEN]) for the broadcast address, then set it
using the existing helper.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware has a somewhat quirky protocol for reading out the VTU
entry for a particular VID. But there is no reason why we cannot
create a better API for ourselves in the driver.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the intricacies of correctly iterating over the VTU to a common
implementation.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a port is a part of a LAG, the ATU will create dynamic entries
belonging to the LAG ID when learning is enabled. So trying to
fast-age those out using the constituent port will have no
effect. Unfortunately the hardware does not support move operations on
LAGs so there is no obvious way to transform the request to target the
LAG instead.

Instead we document this known limitation and at least avoid wasting
any time on it.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order for a driver to be able to query a bridge for information
about itself, e.g. reading out port flags, it has to use a netdev that
is known to the bridge. In the simple case, that is just the netdev
representing the port, e.g. swp0 or swp1 in this example:

   br0
   / \
swp0 swp1

But in the case of an offloaded lag, this will be the bond or team
interface, e.g. bond0 in this example:

     br0
     /
  bond0
   / \
swp0 swp1

Add a helper that hides some of this complexity from the
drivers. Then, redefine dsa_port_offloads_bridge_port using the helper
to avoid double accounting of the set of possible offloaded uppers.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: ipa: support 32-bit targets

There is currently a configuration dependency that restricts IPA to
be supported only on 64-bit machines.  There are only a few things
that really require that, and those are fixed in this series.  The
last patch in the series removes the CONFIG_64BIT build dependency
for IPA.

Version 2 of this series uses upper_32_bits() rather than creating
a new function to extract bits out of a DMA address.  Version 3 of
uses lower_32_bits() as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently assume the IPA driver is built only for a 64 bit kernel.

When this constraint was put in place it eliminated some do_div()
calls, replacing them with the "/" and "%" operators.  We now only
use these operations on u32 and size_t objects.  In a 32-bit kernel
build, size_t will be 32 bits wide, so there remains no reason to
use do_div() for divide and modulo.

A few recent commits also fix some code that assumes that DMA
addresses are 64 bits wide.

With that, we can get rid of the 64-bit build requirement.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently have a build-time check to ensure that the minimum DMA
allocation alignment satisfies the constraint that IPA filter and
route tables must point to rules that are 128-byte aligned.

But what's really important is that the actual allocated DMA memory
has that alignment, even if the minimum is smaller than that.

Remove the BUILD_BUG_ON() call checking against minimim DMA alignment
and instead verify at rutime that the allocated memory is properly
aligned.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use upper_32_bits() to extract the high-order 32 bits of a DMA
address.  This avoids doing a 32-position shift on a DMA address
if it happens not to be 64 bits wide.  Use lower_32_bits() to
extract the low-order 32 bits (because that's what it's for).
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some build time checks in ipa_table_validate_build() assume that a
DMA address is 64 bits wide.  That is more restrictive than it has
to be.  A route or filter table is 64 bits wide no matter what the
size of a DMA address is on the AP.  The code actually uses a
pointer to __le64 to access table entries, and a fixed constant
IPA_TABLE_ENTRY_SIZE to describe the size of those entries.

Loosen up two checks so they still verify some requirements, but
such that they do not assume the size of a DMA address is 64 bits.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2021-03-18

please apply the following patch series for qeth to netdev's net-next
tree.

This brings two small optimizations (replace a hard-coded GFP_ATOMIC,
pass through the NAPI budget to enable napi_consume_skb()), and removes
some redundant VLAN filter code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The callbacks have been slimmed down to a level where they no longer do
any actual work. So stop pretending that we support the
NETIF_F_HW_VLAN_CTAG_FILTER feature.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pending TX buffers are completed from the same NAPI code as normal
TX buffers. Pass the NAPI budget to qeth_tx_complete_buf() so that
the freeing of the completed skbs can be deferred.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth_init_qdio_out_buf() is typically called during initialization, and
the GFP_ATOMIC is only needed for a very specific & rare case during TX
completion.

Allow callers to specify a gfp mask, so that the initialization path can
select GFP_KERNEL. While at it also clarify the function name.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: xps: improve the xps maps handling

This series aims at fixing various issues with the xps code, including
out-of-bound accesses and use-after-free. While doing so we try to
improve the xps code maintainability and readability.

The main change is moving dev->num_tc and dev->nr_ids in the xps maps, to
avoid out-of-bound accesses as those two fields can be updated after the
maps have been allocated. This allows further reworks, to improve the
xps code readability and allow to stop taking the rtnl lock when
reading the maps in sysfs. The maps are moved to an array in net_device,
which simplifies the code a lot.

One future improvement may be to remove the use of xps_map_mutex from
net/core/dev.c, but that may require extra care.

Thanks!
Antoine

Since v3:
  - Removed the 3 patches about the rtnl lock and __netif_set_xps_queue
    as there are extra issues. Those patches were not tied to the
    others, and I'll see want can be done as a separate effort.
  - One small fix in patch 12.

Since v2:
  - Patches 13-16 are new to the series.
  - Fixed another issue I found while preparing v3 (use after free of
    old xps maps).
  - Kept the rtnl lock when calling netdev_get_tx_queue and
    netdev_txq_to_tc.
  - Use get_device/put_device when using the sb_dev.
  - Take the rtnl lock in mlx5 and virtio_net when calling
    netif_set_xps_queue.
  - Fixed a coding style issue.

Since v1:
  - Reordered the patches to improve readability and avoid introducing
    issues in between patches.
  - Use dev_maps->nr_ids to allocate the mask in xps_queue_show but
    still default to nr_cpu_ids/dev->num_rx_queues in xps_queue_show
    when dev_maps hasn't been allocated yet for backward
    compatibility.:w
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In __netif_set_xps_queue, old map entries from the old dev_maps are
freed but their corresponding entry in the old dev_maps aren't NULLed.
Fix this.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When setting up an new dev_maps in __netif_set_xps_queue, we remove and
free maps from unused CPUs/rx-queues near the end of the function; by
calling remove_xps_queue. However it's possible those maps are also part
of the old not-freed-yet dev_maps, which might be used concurrently.
When that happens, a map can be freed while its corresponding entry in
the old dev_maps table isn't NULLed, leading to: "BUG: KASAN:
use-after-free" in different places.

This fixes the map freeing logic for unused CPUs/rx-queues, to also NULL
the map entries from the old dev_maps table.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most of the xps_cpus_show and xps_rxqs_show functions share the same
logic. Having it in two different functions does not help maintenance.
This patch moves their common logic into a new function, xps_queue_show,
to improve this.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that nr_ids and num_tc are stored in the xps dev_maps, which are RCU
protected, we do not have the need to protect the maps in the rtnl lock.
Move the rtnl unlock up so we reduce the rtnl locking section.

We also increase the reference count on the subordinate device if any,
as we don't want this device to be freed while we use it (now that the
rtnl lock isn't protecting it in the whole function).
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Improve the readability of the loop removing tx-queue from unused
CPUs/rx-queues in __netif_set_xps_queue. The change should only be
cosmetic.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds an helper, xps_copy_dev_maps, to copy maps from dev_maps
to new_dev_maps at a given index. The logic should be the same, with an
improved code readability and maintenance.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the xps maps (xps_cpus_map and xps_rxqs_map) to an array in
net_device. That will simplify a lot the code removing the need for lots
of if/else conditionals as the correct map will be available using its
offset in the array.

This should not modify the xps maps behaviour in any way.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the xps possible_mask. It was an optimization but we can just
loop from 0 to nr_ids now that it is embedded in the xps dev_maps. That
simplifies the code a bit.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Embed nr_ids (the number of cpu for the xps cpus map, and the number of
rxqs for the xps cpus map) in dev_maps. That will help not accessing out
of bound memory if those values change after dev_maps was allocated.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The xps cpus/rxqs map is accessed using dev->num_tc, which is used when
allocating the map. But later updates of dev->num_tc can lead to having
a mismatch between the maps and how they're accessed. In such cases the
map values do not make any sense and out of bound accesses can occur
(that can be easily seen using KASAN).

This patch aims at fixing this by embedding num_tc into the maps, using
the value at the time the map is created. This brings two improvements:
- The maps can be accessed using the embedded num_tc, so we know for
  sure we won't have out of bound accesses.
- Checks can be made before accessing the maps so we know the values
  retrieved will make sense.

We also update __netif_set_xps_queue to conditionally copy old maps from
dev_maps in the new one only if the number of traffic classes from both
maps match.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the implementations of xps_cpus_show and xps_rxqs_show to converge,
as the two share the same logic but diverted over time. This should not
modify their behaviour but will help future changes and improve
maintenance.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In net-sysfs, get_netdev_queue_index returns an unsigned int. Some of
its callers use an unsigned long to store the returned value. Update the
code to be consistent, this should only be cosmetic.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use bitmap_zalloc instead of zalloc_cpumask_var in xps_cpus_show to
align with xps_rxqs_show. This will improve maintenance and allow us to
factorize the two functions. The function should behave the same.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

BCM4908 has only 1 RGMII reg for controlling port 7.

Fixes: 73b7a604 ("net: dsa: bcm_sf2: support BCM4908's integrated switch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simple macro like REG_RGMII_CNTRL_P() is insufficient as:
1. It doesn't validate port argument
2. It doesn't support chipsets with non-lineral RGMII regs layout

Missing port validation could result in getting register offset from out
of array. Random memory -> random offset -> random reads/writes. It
affected e.g. BCM4908 for REG_RGMII_CNTRL_P(7).

Fixes: a78e86ed ("net: dsa: bcm_sf2: Prepare for different register layouts")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device tree support to b53_mmap.c while keeping platform devices support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mohammad Athari Bin Ismail says:

====================
net: stmmac: EST interrupts and ethtool

This patchset adds support for handling EST interrupts and reporting EST
errors. Additionally, the errors are added into ethtool statistic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Below EST errors are added into ethtool statistic:
1) Constant Gate Control Error (CGCE):
   The counter "mtl_est_cgce" increases everytime CGCE interrupt is
   triggered.

2) Head-of-Line Blocking due to Scheduling (HLBS):
   The counter "mtl_est_hlbs" increases everytime HLBS interrupt is
   triggered.

3) Head-of-Line Blocking due to Frame Size (HLBF):
   The counter "mtl_est_hlbf" increases everytime HLBF interrupt is
   triggered.

4) Base Time Register error (BTRE):
   The counter "mtl_est_btre" increases everytime BTRE interrupt is
   triggered but BTRL not reaches maximum value of 15.

5) Base Time Register Error Loop Count (BTRL) reaches maximum value:
   The counter "mtl_est_btrlm" increases everytime BTRE interrupt is
   triggered and BTRL value reaches maximum value of 15.

Please refer to MTL_EST_STATUS register in DesignWare Cores Ethernet
Quality-of-Service Databook for more detail explanation.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enabled EST related interrupts as below:
1) Constant Gate Control Error (CGCE)
2) Head-of-Line Blocking due to Scheduling (HLBS)
3) Head-of-Line Blocking due to Frame Size (HLBF).
4) Base Time Register error (BTRE)
5) Switch to S/W owned list Complete (SWLC)

For HLBS, the user will get the info of all the queues that shows this
error. For HLBF, the user will get the info of all the queue with the
latest frame size which causes the error. Frame size 0 indicates no
error.

The ISR handling takes place when EST feature is enabled by user.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Co-developed-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ong Boon Leong says:

====================
stmmac: add VLAN priority based RX steering

The current tc flower implementation in stmmac supports both L3 and L4
filter offloading. This patch adds the support of VLAN priority based
RX frame steering into different Rx Queues.

The patches have been tested on both configuration test (include L3/L4)
and traffic test (multi VLAN ping streams with RX Frame Steering) below:-

> tc qdisc delete dev eth0 ingress

> tc qdisc del dev eth0 parent root 2&> /dev/null
> tc qdisc del dev eth0 parent ffff: 2&> /dev/null

> tc qdisc add dev eth0 ingress

> tc filter add dev eth0 parent ffff: protocol ip flower dst_ip 192.168.0.1 \
  src_ip 192.168.1.1 ip_proto tcp dst_port 5201 src_port 6201 action drop

> tc filter add dev eth0 parent ffff: protocol ip flower dst_ip 192.168.0.2 \
  src_ip 192.168.1.2 ip_proto tcp dst_port 5202 src_port 6202 action drop

> tc filter show dev eth0 ingress
filter parent ffff: protocol ip pref 49151 flower chain 0
filter parent ffff: protocol ip pref 49151 flower chain 0 handle 0x1
  eth_type ipv4
  ip_proto tcp
  dst_ip 192.168.0.2
  src_ip 192.168.1.2
  dst_port 5202
  src_port 6202
  in_hw in_hw_count 1
        action order 1: gact action drop
         random type none pass val 0
         index 2 ref 1 bind 1

filter parent ffff: protocol ip pref 49152 flower chain 0
filter parent ffff: protocol ip pref 49152 flower chain 0 handle 0x1
  eth_type ipv4
  ip_proto tcp
  dst_ip 192.168.0.1
  src_ip 192.168.1.1
  dst_port 5201
  src_port 6201
  in_hw in_hw_count 1
        action order 1: gact action drop
         random type none pass val 0
         index 1 ref 1 bind 1

> tc qdisc delete dev eth0 ingress

> tc qdisc del dev eth0 parent root 2&> /dev/null
> tc qdisc del dev eth0 parent ffff: 2&> /dev/null

> tc qdisc add dev eth0 ingress

> tc qdisc add dev eth0 root mqprio num_tc 4 \
  map 0 1 2 3 0 0 0 0 0 0 0 0 0 0 0 0 \
  queues 1@0 1@1 1@2 1@3 hw 0

> tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 0 hw_tc 3

> tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 1 hw_tc 2

> tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 2 hw_tc 1

> tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 3 hw_tc 0

> tc filter show dev eth0 ingress
filter parent ffff: protocol 802.1Q pref 49149 flower chain 0
filter parent ffff: protocol 802.1Q pref 49149 flower chain 0 handle 0x1 hw_tc 0
  vlan_prio 3
  in_hw in_hw_count 1
filter parent ffff: protocol 802.1Q pref 49150 flower chain 0
filter parent ffff: protocol 802.1Q pref 49150 flower chain 0 handle 0x1 hw_tc 1
  vlan_prio 2
  in_hw in_hw_count 1
filter parent ffff: protocol 802.1Q pref 49151 flower chain 0
filter parent ffff: protocol 802.1Q pref 49151 flower chain 0 handle 0x1 hw_tc 2
  vlan_prio 1
  in_hw in_hw_count 1
filter parent ffff: protocol 802.1Q pref 49152 flower chain 0
filter parent ffff: protocol 802.1Q pref 49152 flower chain 0 handle 0x1 hw_tc 3
  vlan_prio 0
  in_hw in_hw_count 1

> tc qdisc delete dev eth0 ingress

> ip address flush dev eth0
> ip address add 169.254.1.11/24 dev eth0

> ip link delete dev eth0.vlan1 2> /dev/null
> ip link add link eth0 name eth0.vlan1 type vlan id 1
> ip address flush dev eth0.vlan1 2> /dev/null
> ip address add 169.254.11.11/24 dev eth0.vlan1

> ip link delete dev eth0.vlan2 2> /dev/null
> ip link add link eth0 name eth0.vlan2 type vlan id 2
> ip address flush dev eth0.vlan2 2> /dev/null
> ip address add 169.254.12.11/24 dev eth0.vlan2

> ip link delete dev eth0.vlan3 2> /dev/null
> ip link add link eth0 name eth0.vlan3 type vlan id 3
> ip address flush dev eth0.vlan3 2> /dev/null
> ip address add 169.254.13.11/24 dev eth0.vlan3

> ip link delete dev eth0.vlan4 2> /dev/null
> ip link add link eth0 name eth0.vlan4 type vlan id 4
> ip address flush dev eth0.vlan4 2> /dev/null
> ip address add 169.254.14.11/24 dev eth0.vlan4

> ip address flush dev eth0
> ip address add 169.254.1.22/24 dev eth0

> ip link delete dev eth0.vlan1 2> /dev/null
> ip link add link eth0 name eth0.vlan1 type vlan id 1
> ip address flush dev eth0.vlan1 2> /dev/null
> ip address add 169.254.11.22/24 dev eth0.vlan1

> ip link delete dev eth0.vlan2 2> /dev/null
> ip link add link eth0 name eth0.vlan2 type vlan id 2
> ip address flush dev eth0.vlan2 2> /dev/null
> ip address add 169.254.12.22/24 dev eth0.vlan2

> ip link delete dev eth0.vlan3 2> /dev/null
> ip link add link eth0 name eth0.vlan3 type vlan id 3
> ip address flush dev eth0.vlan3 2> /dev/null
> ip address add 169.254.13.22/24 dev eth0.vlan3

> ip link delete dev eth0.vlan4 2> /dev/null
> ip link add link eth0 name eth0.vlan4 type vlan id 4
> ip address flush dev eth0.vlan4 2> /dev/null
> ip address add 169.254.14.22/24 dev eth0.vlan4

> mkdir -p /sys/fs/cgroup/net_prio/grp0
> echo eth0 0 > /sys/fs/cgroup/net_prio/grp0/net_prio.ifpriomap
> echo eth0.vlan1 0 >  /sys/fs/cgroup/net_prio/grp0/net_prio.ifpriomap
> mkdir -p /sys/fs/cgroup/net_prio/grp1
> echo eth0 0 > /sys/fs/cgroup/net_prio/grp1/net_prio.ifpriomap
> echo eth0.vlan2 1 >  /sys/fs/cgroup/net_prio/grp1/net_prio.ifpriomap
> mkdir -p /sys/fs/cgroup/net_prio/grp2
> echo eth0 0 > /sys/fs/cgroup/net_prio/grp2/net_prio.ifpriomap
> echo eth0.vlan3 2 >  /sys/fs/cgroup/net_prio/grp2/net_prio.ifpriomap
> mkdir -p /sys/fs/cgroup/net_prio/grp3
> echo eth0 0 > /sys/fs/cgroup/net_prio/grp3/net_prio.ifpriomap
> echo eth0.vlan4 3 >  /sys/fs/cgroup/net_prio/grp3/net_prio.ifpriomap

> tc qdisc del dev eth0 parent root 2&> /dev/null
> tc qdisc del dev eth0 parent ffff: 2&> /dev/null

> tc qdisc add dev eth0 ingress
> tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 0 0 0 0 0 0 0 0 0 0 0 queues 1@0 1@1 1@2 1@3 hw 0

> tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 0 hw_tc 0

> tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 1 hw_tc 1

> tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 2 hw_tc 2

> tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 3 hw_tc 3

> ip link set eth0.vlan1 type vlan egress-qos-map 0:0
> ip link set eth0.vlan2 type vlan egress-qos-map 1:1
> ip link set eth0.vlan3 type vlan egress-qos-map 2:2
> ip link set eth0.vlan4 type vlan egress-qos-map 3:3

> tc filter show dev eth0 ingress
filter parent ffff: protocol 802.1Q pref 49149 flower chain 0
filter parent ffff: protocol 802.1Q pref 49149 flower chain 0 handle 0x1 hw_tc 3
  vlan_prio 3
  in_hw in_hw_count 1
filter parent ffff: protocol 802.1Q pref 49150 flower chain 0
filter parent ffff: protocol 802.1Q pref 49150 flower chain 0 handle 0x1 hw_tc 2
  vlan_prio 2
  in_hw in_hw_count 1
filter parent ffff: protocol 802.1Q pref 49151 flower chain 0
filter parent ffff: protocol 802.1Q pref 49151 flower chain 0 handle 0x1 hw_tc 1
  vlan_prio 1
  in_hw in_hw_count 1
filter parent ffff: protocol 802.1Q pref 49152 flower chain 0
filter parent ffff: protocol 802.1Q pref 49152 flower chain 0 handle 0x1 hw_tc 0
  vlan_prio 0
  in_hw in_hw_count 1

> echo 1 > /proc/irq/131/smp_affinity
> echo 1 > /proc/irq/132/smp_affinity

> echo 4 > /proc/irq/133/smp_affinity
> echo 4 > /proc/irq/134/smp_affinity

> echo 4 > /proc/irq/135/smp_affinity
> echo 4 > /proc/irq/136/smp_affinity

> echo 2 > /proc/irq/137/smp_affinity
> echo 2 > /proc/irq/138/smp_affinity

> ping -i 0.001 169.254.11.22 2&> /dev/null &
> PID1="$!"
> echo $PID1 >  /sys/fs/cgroup/net_prio/grp0/cgroup.procs

> ping -i 0.001 169.254.12.22 2&> /dev/null &
> PID2="$!"
> echo $PID2 >  /sys/fs/cgroup/net_prio/grp1/cgroup.procs

> ping -i 0.001 169.254.13.22 2&> /dev/null &
> PID3="$!"
> echo $PID3 >  /sys/fs/cgroup/net_prio/grp2/cgroup.procs

> ping -i 0.001 169.254.14.22 2&> /dev/null &
> PID4="$!"
> echo $PID4 >  /sys/fs/cgroup/net_prio/grp3/cgroup.procs

> ping -i 0.001 169.254.11.11 2&> /dev/null &
> PID1="$!"
> echo $PID1 >  /sys/fs/cgroup/net_prio/grp0/cgroup.procs

> ping -i 0.001 169.254.12.11 2&> /dev/null &
> PID2="$!"
> echo $PID2 >  /sys/fs/cgroup/net_prio/grp1/cgroup.procs

> ping -i 0.001 169.254.13.11 2&> /dev/null &
> PID3="$!"
> echo $PID3 >  /sys/fs/cgroup/net_prio/grp2/cgroup.procs

> ping -i 0.001 169.254.14.11 2&> /dev/null &
> PID4="$!"
> echo $PID4 >  /sys/fs/cgroup/net_prio/grp3/cgroup.procs

> watch -n 0.5 -d "cat /proc/interrupts | grep eth0"
 131:     251918         41          0          0  IR-PCI-MSI 477184-edge      eth0:rx-0
 132:      18969          1          0          0  IR-PCI-MSI 477185-edge      eth0:tx-0
 133:          0          0     295872          0  IR-PCI-MSI 477186-edge      eth0:rx-1
 134:          0          0      16136          0  IR-PCI-MSI 477187-edge      eth0:tx-1
 135:          0          0     288042          0  IR-PCI-MSI 477188-edge      eth0:rx-2
 136:          0          0      16135          0  IR-PCI-MSI 477189-edge      eth0:tx-2
 137:          0     211177          0          0  IR-PCI-MSI 477190-edge      eth0:rx-3
 138:          2      16144          0          0  IR-PCI-MSI 477191-edge      eth0:tx-3
 139:          0          0          0          0  IR-PCI-MSI 477192-edge      eth0:rx-4
 140:          0          0          0          0  IR-PCI-MSI 477193-edge      eth0:tx-4
 141:          0          0          0          0  IR-PCI-MSI 477194-edge      eth0:rx-5
 142:          0          0          0          0  IR-PCI-MSI 477195-edge      eth0:tx-5
 143:          0          0          0          0  IR-PCI-MSI 477196-edge      eth0:rx-6
 144:          0          0          0          0  IR-PCI-MSI 477197-edge      eth0:tx-6
 145:          0          0          0          0  IR-PCI-MSI 477198-edge      eth0:rx-7
 146:          0          0          0          0  IR-PCI-MSI 477199-edge      eth0:tx-7
 157:          0          0          0          0  IR-PCI-MSI 477210-edge      eth0:safety-ue

====================
Signed-off-by: David S. Miller <davem@davemloft.net>