Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-03-06

This series contains updates to e1000, e1000e and igb.

Yanir provides updates to e1000e based on the patches provided by John
Linville.  First updates the code comment to better describe the changes
and the impact on the driver.  Second removed calls to ioremap/unmap for
i219 since this is only relevant to older hardware only.  Starting with
i219, the NVM will not be mapped to its one BAR but to a address region
in another bar.

Alex Duyck provides two fixes for igb, first fixes a compile warning
where a variable may be used uninitialized, so Alex initializes it.
Second fixes an issue where all of the pin register values were having
to be pushed onto the stack each time the function was called, so to
avoid this, Alex made them static const so that they should only need
to be allocated once and we can avoid all the instructions to get them
onto the stack.

Eliezer found an issue in e1000 where we needed to be calling
netif_carrier_off earlier in the down() to prevent the stack from
queuing more packets to the interface.

Sabrina Dubroca resolved a potential race condition by adding a
dummy allocator.  There was a race condition between e1000_change_mtu()
cleanups and netpoll, when changing the MTU across jumbo sizes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fan Du says:

====================
Improvements for TCP PMTU

This patchset performs some improvements and enhancement
for current TCP PMTU as per RFC4821 with the aim to find
optimal mms size quickly, and also be adaptive to route
changes like enlarged path MTU. Then TCP PMTU could be
used to probe a effective pmtu in absence of ICMP message
for tunnels(e.g. vxlan) across different networking stack.

Patch1/4: Set probe mss base to 1024 Bytes per RFC4821
Patch2/4: Do not double probe_size for each probing,
          use a simple binary search to gain maximum performance.
	  mss for next probing.
Patch3/4: Create a probe timer to detect enlarged path MTU.
Patch4/4: Update ip-sysctl.txt for new sysctl knobs.

Changelog:
v5:
  - Zero probe_size before resetting search range.
  - Update ip-sysctl.txt for new sysctl knobs.
v4:
  - Convert probe_size to mss, not directly from search_low/high
  - Clamp probe_threshold
  - Don't adjust search_high in blackhole probe, so drop orignal patch3
v3:
  - Update commit message for patch2
  - Fix pseudo timer delta calculation in patch4
v2:
  - Introduce sysctl_tcp_probe_threshold to control when
    probing will stop, as suggested by John Heffner.
  - Add patch3 to shrink current mss value for search low boundary.
  - Drop cannonical timer usages, implements pseudo timer based on
    32bits jiffies tcp_time_stamp, as suggested by Eric Dumazet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Namely tcp_probe_interval to control how often to restart
a probe. And tcp_probe_threshold to control when stop the
probing in respect to the width of search range in bytes
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As per RFC4821 7.3.  Selecting Probe Size, a probe timer should
be armed once probing has converged. Once this timer expired,
probing again to take advantage of any path PMTU change. The
recommended probing interval is 10 minutes per RFC1981. Probing
interval could be sysctled by sysctl_tcp_probe_interval.

Eric Dumazet suggested to implement pseudo timer based on 32bits
jiffies tcp_time_stamp instead of using classic timer for such
rare event.
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current probe_size is chosen by doubling mss_cache,
the probing process will end shortly with a sub-optimal
mss size, and the link mtu will not be taken full
advantage of, in return, this will make user to tweak
tcp_base_mss with care.

Use binary search to choose probe_size in a fine
granularity manner, an optimal mss will be found
to boost performance as its maxmium.

In addition, introduce a sysctl_tcp_probe_threshold
to control when probing will stop in respect to
the width of search range.

Test env:
Docker instance with vxlan encapuslation(82599EB)
iperf -c 10.0.0.24  -t 60

before this patch:
1.26 Gbits/sec

After this patch: increase 26%
1.59 Gbits/sec
Signed-off-by: Fan Du <fan.du@intel.com>
Acked-by: John Heffner <johnwheffner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Quotes from RFC4821 7.2.  Selecting Initial Values

   It is RECOMMENDED that search_low be initially set to an MTU size
   that is likely to work over a very wide range of environments.  Given
   today's technologies, a value of 1024 bytes is probably safe enough.
   The initial value for search_low SHOULD be configurable.

Moreover, set a small value will introduce extra time for the search
to converge. So set the initial probe base mss size to 1024 Bytes.
Signed-off-by: Fan Du <fan.du@intel.com>
Acked-by: John Heffner <johnwheffner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Other users users of the neighbour table use neigh->output as the method
to decided when and which link-layer header to place on a packet.
DECnet has been using neigh->output to decide which DECnet headers to
place on a packet depending which neighbour the packet is destined for.

The DECnet usage isn't totally wrong but it can run into problems if the
neighbour output function is run for a second time as the teql driver
and the bridge netfilter code can do.

Therefore to avoid pathologic problems later down the line and make the
neighbour code easier to understand by refactoring the decnet output
code to only use a neighbour method to add a link layer header to a
packet.

This is done by moving the neigbhour operations lookup from
dn_to_neigh_output to dn_neigh_output_packet.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patches implements the poll_controller support for all
bonding driver. If the slaves have poll_controller net_op defined,
this implementation calls them. This is mode agnostic implementation
and iterates through all slaves (based on mode) and calls respective
handler.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a race condition between e1000_change_mtu's cleanups and
netpoll, when we change the MTU across jumbo size:

Changing MTU frees all the rx buffers:
    e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings ->
        e1000_clean_rx_ring

Then, close to the end of e1000_change_mtu:
    pr_info -> ... -> netpoll_poll_dev -> e1000_clean ->
        e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag

And when we come back to do the rest of the MTU change:
    e1000_up -> e1000_configure -> e1000_configure_rx ->
        e1000_alloc_jumbo_rx_buffers

alloc_jumbo finds the buffers already != NULL, since data (shared with
page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage,
or at least not what is expected when in jumbo state.

This results in an unusable adapter (packets don't get through), and a
NULL pointer dereference on the next call to e1000_clean_rx_ring
(other mtu change, link down, shutdown):

BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330

    [...]

Call Trace:
 [<ffffffff81195445>] put_page+0x55/0x60
 [<ffffffff815d9f44>] e1000_clean_rx_ring+0x134/0x200
 [<ffffffff815da055>] e1000_clean_all_rx_rings+0x45/0x60
 [<ffffffff815df5e0>] e1000_down+0x1c0/0x1d0
 [<ffffffff811e2260>] ? deactivate_slab+0x7f0/0x840
 [<ffffffff815e21bc>] e1000_change_mtu+0xdc/0x170
 [<ffffffff81647050>] dev_set_mtu+0xa0/0x140
 [<ffffffff81664218>] do_setlink+0x218/0xac0
 [<ffffffff814459e9>] ? nla_parse+0xb9/0x120
 [<ffffffff816652d0>] rtnl_newlink+0x6d0/0x890
 [<ffffffff8104f000>] ? kvm_clock_read+0x20/0x40
 [<ffffffff810a2068>] ? sched_clock_cpu+0xa8/0x100
 [<ffffffff81663802>] rtnetlink_rcv_msg+0x92/0x260

By setting the allocator to a dummy version, netpoll can't mess up our
rx buffers.  The allocator is set back to a sane value in
e1000_configure_rx.

Fixes: edbbb3ca ("e1000: implement jumbo receive with partial descriptors")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.

Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.

Move netif_carrier_off as early as possible.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

While addressing the pin problem I noticed that all of the pin register
values where having to be pushed onto the stack each time the function was
called.  To avoid that I am making them static const so that they should
only need to be allocated once and we can avoid all the instructions to get
them onto the stack..

size before:
   text	   data	    bss	    dec	    hex	filename
 161477	  10512	      8	 171997	  29fdd	drivers/net/ethernet/intel/igb/igb.ko

size after:
   text	   data	    bss	    dec	    hex	filename
 161205	  10512	      8	 171725	  29ecd	drivers/net/ethernet/intel/igb/igb.ko
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When building the kernel using the gcc 4.8.3 compiler included in Fedora 20
I was repeatedly seeing the warning:

 drivers/net/ethernet/intel/igb/igb_ptp.c: In function ‘igb_ptp_feature_enable_i210’:
 drivers/net/ethernet/intel/igb/igb_ptp.c:395:21: warning: ‘pin’ may be used uninitialized in this function
 [-Wmaybe-uninitialized]
   tssdp &= ~ts_sdp_en[pin];
                     ^
 drivers/net/ethernet/intel/igb/igb_ptp.c:471:6: note: ‘pin’ was declared here
   int pin;
       ^

To resolve it I am assigning the pin a value of -1 when it is instantiated.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Starting I219, the NVM will not be mapped to its own BAR, but to an
address region in another bar.  The mapping/unmapping is relevant
to older HW only.

CC: John W Linville <linville@tuxdriver.com>
Reported-by: John W Linville <linville@tuxdriver.com>
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The interface to the device flash was modified in i219 and later HW.
This patch better describes the change and the impact on the driver.

CC: John W Linville <linville@tuxdriver.com>
Reported-by: John W Linville <linville@tuxdriver.com>
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net/ipv4/fib_trie.c: In function ‘fib_table_flush_external’:
net/ipv4/fib_trie.c:1572:6: warning: unused variable ‘found’ [-Wunused-variable]
  int found = 0;
      ^
net/ipv4/fib_trie.c:1571:16: warning: unused variable ‘slen’ [-Wunused-variable]
  unsigned char slen;
                ^
Signed-off-by: David S. Miller <davem@davemloft.net>

Scott Feldman says:

====================
switchdev: add IPv4 routing offload

v4:

  - Add NETIF_F_NETNS_LOCAL to rocker port feature list to keep rocker
    ports in the default netns.  Rocker hardware can't be partitioned
    to support multiple namespaces, currently.  It would be interesting
    to add netns support to rocker device by basically adding another
    match field to each table to match on some unique netns ID, with
    a port knowing it's netns ID.  Future work TDB.
  - Up-level the RTNH_F_EXTERNAL marking of routes installed to offload
    device from driver to switchdev common code.  Now driver can't skip
    routes.  Either it can install the route or it cannot.  Yes or No.
    If no on any route, all offloading is aborted by removing routes
    from offload device and setting ipv4.fib_offload_disabled so no more
    routes can be offloaded.  This is harsh, but it's our starting point.
    We can refine the policies in follow-up work.
  - Add new net.ipv4.fib_offload_disabled bool that is set if anything
    goes wrong with route offloading.  We can refine this later to make
    the setting per-device or per-device-port-netdev, but let's start
    here simple and refine in follow-up work.
  - Rebase against Alex's latest FIB changes.  I think I did everything
    correctly, and didn't run into any issues with testing, but I'd like
    Alex to look over the changes and maybe follow-up with any cleanups.

v3:

Changes based on v2 review comments:

  - Move check for custom rules up earlier in patch set, to keep git bisect
    safe.
  - Simplify the route add/modify failure handling to simple try until
    failure, and then on failure, undo everything.  The switchdev driver
    will return err when route can normally be installed to device, but
    the install fails for one reason or another (no space left on device,
    etc).  If a failure happens, uninstall all routes from the device,
    punting forwarding for all routes back to the kernel.
  - Scan route's full nexthop list, ensuring all nexthop devs belong
    to the same switchdev device, otherwise don't try to install route
    to device.

v2:

Changes based on v1 review comments and discussions at netconf:

  - Allow route modification, but use same ndo op used for adding route.
    Driver/device is expected to modify route in-place, if it can, to avoid
    interruption of service.
  - Add new RTNH_F_EXTERNAL flag to mark FIB entries offloaded externally.
  - Don't offload routes if using custom IP rules.  If routes are already
    offloaded, and custom IP rules are turned on, flush routes from offload
    device.  (Offloaded routes are marked with RTNH_F_EXTERNAL).
  - Use kernel's neigh resolution code to resolve route's nexthops' neigh
    MAC addrs.  (Thanks davem, works great!).
  - Use fib->fib_priority in rocker driver to give priorities to routes in
    OF-DPA unicast route table.

v1:

This patch set adds L3 routing offload support for IPv4 routes.  The idea is to
mirror routes installed in the kernel's FIB down to a hardware switch device to
offload the data forwarding path for L3.  Only the data forwarding path is
intercepted.  Control and management of the kernel's FIB remains with the
kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver implements ndo_switch_fib_ipv4_add/del ops to add/del/mod IPv4
routes to/from switchdev device.  Once a route is added to the device, and the
route's nexthops are resolved to neighbor MAC address, the device will forward
matching pkts rather than the kernel.  This offloads the L3 forwarding path
from the kernel to the device.  Note that control and management planes are
still mananged by Linux; only the data plane is offloaded.  Standard routing
control protocols such as OSPF and BGP run on Linux and manage the kernel's FIB
via standard rtm netlink msgs...nothing changes here.

A new hash table is added to rocker to track neighbors.  The driver listens for
neighbor updates events using netevent notifier NETEVENT_NEIGH_UPDATE.  Any ARP
table updates for ports on this device are recorded in this table.  Routes
installed to the device with nexthops that reference neighbors in this table
are "qualified".  In the case of a route with nexthops not resolved in the
table, the kernel is asked to resolve the nexthop.

The driver uses fib_info->fib_priority for the priority field in rocker's
unicast routing table.

The device can only forward to pkts matching route dst to resolved nexthops.
Currently, the device only supports single-path routes (i.e. routes with one
nexthop).  Equal Cost Multipath (ECMP) route support will be added in followup
patches.

This patch is driver support for unicast IPv4 routing only.  Followup patches
will add driver and infrastructure for IPv6 routing and multicast routing.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call into the switchdev driver any time an IPv4 fib entry is
added/modified/deleted from the kernel's FIB.  The switchdev driver may or
may not install the route to the offload device.  In the case where the
driver tries to install the route and something goes wrong (device's routing
table is full, etc), then all of the offloaded routes will be flushed from the
device, route forwarding falls back to the kernel, and no more routes are
offloading.

We can refine this logic later.  For now, use the simplist model of offloading
routes up to the point of failure, and then on failure, undo everything and
mark IPv4 offloading disabled.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If something goes wrong with IPv4 FIB offload, mark entire net offload
disabled.  This is brute force policy to basically shut down IPv4 FIB offload
permanently if there is a problem offloading any route to an external device.
We can refine the policy in the future, to handle failures on a per-device or
per-route basis, but for now, this policy is per-net.

What we're trying to avoid is an inconsistent split between the kernel's FIB
and the offload device's FIB.  We don't want the device to fwd a pkt
inconsitent with what the kernel would do.  An example of a split is if device
has 10.0.0.0/16 and kernel has 10.0.0.0/16 and 10.0.0.0/24, the device wouldn't
see the longest prefix 10.0.0.0/24 and potentially forward pkts incorrectly.

Limited capacity or limited capability are two ways a route may fail to install
to the offload device.  We'll not differentiate between failures at this time,
and treat any failure as fatal and mark the net as fib_offload_disabled.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flesh out ndo wrappers to call into device driver.  To call into device driver,
the wrapper must interate over route's nexthops to ensure all nexthop devs
belong to the same switch device.  Currently, there is no support for route's
nexthops spanning offloaded and non-offloaded devices, or spanning ports of
multiple offload devices.

Since switch device ports may be stacked under virtual interfaces (bonds and/or
bridges), and the route's nexthop may be on the virtual interface, the wrapper
will traverse the nexthop dev down to the base dev.  It's the base dev that's
passed to the switchdev driver's ndo ops.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Keep switchdev FIB offload model simple for now and don't allow custom ip
rules.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add IPv4 fib ndo wrapper funcs and stub them out for now.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add two new ndo ops for IPv4 fib offload support, add and del.  Add uses
modifiy semantics if fib entry already offloaded.  Drivers implementing the new
ndo ops will return err<0 if programming device fails, for example if device's
tables are full.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new RTNH_F_EXTERNAL flag to mark fib entries offloaded externally, for
example to a switchdev switch device.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout

GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.

Tested:

lpx:~# echo 0 >/sys/class/net/eth1/gro_flush_timeout

lpx:~# sar -n DEV 1 10 | grep eth1
10:36:25 AM      eth1  81290.00  40617.00 120479.67   2777.01      0.00      0.00      0.00
10:36:26 AM      eth1  81283.00  40608.00 120481.81   2778.13      0.00      0.00      1.00
10:36:27 AM      eth1  81304.00  40639.00 120518.42   2778.28      0.00      0.00      0.00
10:36:28 AM      eth1  81255.00  40605.00 120437.34   2775.95      0.00      0.00      1.00
10:36:29 AM      eth1  81306.00  40630.00 120521.44   2777.70      0.00      0.00      0.00
10:36:30 AM      eth1  81286.00  40564.00 120480.20   2773.31      0.00      0.00      0.00
10:36:31 AM      eth1  81256.00  40599.00 120438.81   2776.27      0.00      0.00      0.00
10:36:32 AM      eth1  81287.00  40594.00 120480.69   2776.69      0.00      0.00      0.00
10:36:33 AM      eth1  81279.00  40601.00 120478.53   2775.84      0.00      0.00      0.00
10:36:34 AM      eth1  81277.00  40610.00 120476.94   2776.25      0.00      0.00      0.00
Average:         eth1  81282.30  40606.70 120479.39   2776.54      0.00      0.00      0.20

lpx:~# echo 13000 >/sys/class/net/eth1/gro_flush_timeout

lpx:~# sar -n DEV 1 10 | grep eth1
10:36:43 AM      eth1  81257.00   7747.00 120437.44    530.00      0.00      0.00      0.00
10:36:44 AM      eth1  81278.00   7748.00 120480.00    529.85      0.00      0.00      0.00
10:36:45 AM      eth1  81282.00   7752.00 120479.09    531.09      0.00      0.00      0.00
10:36:46 AM      eth1  81282.00   7751.00 120478.80    530.90      0.00      0.00      0.00
10:36:47 AM      eth1  81276.00   7745.00 120478.31    529.64      0.00      0.00      0.00
10:36:48 AM      eth1  81278.00   7747.00 120478.50    529.81      0.00      0.00      0.00
10:36:49 AM      eth1  81282.00   7749.00 120478.88    530.01      0.00      0.00      0.00
10:36:50 AM      eth1  81284.00   7751.00 120481.52    530.20      0.00      0.00      0.00
10:36:51 AM      eth1  81299.00   7769.00 120481.74    533.81      0.00      0.00      0.00
10:36:52 AM      eth1  81281.00   7748.00 120478.62    529.96      0.00      0.00      0.00
Average:         eth1  81279.90   7750.70 120475.29    530.53      0.00      0.00      0.00
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: code re-organization

This pull request contains the first part of the patches required to implement
the grand plan detailed here:

http://www.spinics.net/lists/netdev/msg295942.html

These are mostly code re-organization and function bodies re-arrangement to
allow different callers of lower-level initialization functions for 'struct
dsa_switch' and 'struct dsa_switch_tree' to be later introduced.

There is no functional code change at this point.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract the core logic that setups a 'struct dsa_switch_tree' and
removes it, update dsa_probe() and dsa_remove() to use the two helper
functions. This will be useful to allow for other callers to setup
this structure differently.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to support the new DSA device driver model, a dsa_switch should
be able to advertise the type of tagging protocol supported by the
underlying switch device. This also removes constraints on how tagging
can be stacked to each other.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split the part of dsa_switch_setup() which is responsible for allocating
and initializing a 'struct dsa_switch' and the part which is doing a
given switch device setup and slave network device creation.

This is a preliminary change to allow a separate caller of
dsa_switch_setup_one() which may have externally initialized the
dsa_switch structure, outside of dsa_switch_setup().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for allowing a different model to register DSA switches,
update dsa_of_probe() and dsa_probe() to return -EPROBE_DEFER where
appropriate.

Failure to find a phandle or Device Tree property is still fatal, but
looking up the internal device structure associated with a Device Tree
node is something that might need to be delayed based on driver probe
ordering.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for allowing a different mechanism to register DSA switch
devices and driver, update dsa_of_probe and dsa_of_remove to take a
struct device pointer since neither of these two functions uses the
struct platform_device pointer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

timewait sockets now share a common base with established sockets.

inet_twsk_diag_dump() can use inet_diag_bc_sk() instead of duplicating
code, granted that inet_diag_bc_sk() does proper userlocks
initialization.

twsk_build_assert() will catch any future changes that could break
the assumptions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As pointed out by Ben Hutchings, ioremap uses unsigned long as
its parameter type, so we should be using that instead of u32
or int.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ip/udp bearer can be configured in a point-to-point
mode by specifying both local and remote ip/hostname,
or it can be enabled in multicast mode, where links are
established to all tipc nodes that have joined the same
multicast group. The multicast IP address is generated
based on the TIPC network ID, but can be overridden by
using another multicast address as remote ip.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The payload area following the TIPC discovery message header is an
opaque area defined by the media. INT_H_SIZE was enough for
Ethernet/IB/IPv4 but needs to be expanded to carry IPv6 addressing
information.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to i40e only.

Greg provides fixes for the NPAR transmit scheduler where the driver
initialization caused the BW configurations to not take effect, so use
a BW configuration read and write back to "kick" the transmit scheduler
into action.  Fixes the ethtool offline test, where we were not actually
taking the device offline before doing the testing.

Matt modifies the get and set LED functions so they ignore activity LEDs
since we are required to blink the link LEDs only.

Neerav provides a workaround for whenever a DCBX configuration is changed,
where the firmware doe not set the operational status bit of the
application TLV status as returned from the "Get CEE DCBX Oper Cfg" admin
queue command.  So remove the check for the operational and sync bits of
the application TLV status until a firmware fix is provided.

Shannon changes the driver to grab the NVM devstarter version and not
the image version, since it is the more useful version and is what
should be displayed.  Moves the IRQ tracking setup and tear down into
the same routines that do the IRQ setup and tear down.  This keeps
like activities together and allows us to track exactly the number
of vectors reserved from the OS, which may be fewer than are available
from the hardware.

Jesse provides a fix to use a more portable sign extension by replacing
0xffff.... with ~(u64)0 or ~(u32)0.  Also fixes XPS mask when resetting,
where the driver would accidentally clear the XPS mask for all queues
back to 0.  This caused higher CPU utilization and had some other
performance impacts for transmit tests.  Cleans up some whitespace
formatting.

Catherine provides a fix where some firmware versions are incorrectly
reporting a breakout cable as PHY type 0x3 when it should be 0x16
(I40E_PHY_TYPE_10GBASE_SFPP_CU).  Adds the 10G and 40G AOC PHY types
to the case statement in get_media_type and ethtool get_settings so
that the correct information gets reported back to the user.

Anjali provides IOREMAP changes for future device support, where we
do not want to map the whole CSR space since some of it is mapped by
other drivers with different mapping methods.

Mitch changes the i40e driver to not "spam" the system log with
messages about VF VSI when VFs are created and when they are reset to
reduce user annoyance.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>