Currently when keeping track of qdiscs, mlxsw notes the TC and priomap
corresponding to each qdisc. That is fine currently, as there only ever is
one level of qdiscs to update: the direct children of ETS / PRIO. However
as deeper structures are made offloadable, ETS would need to update these
values for the complete subtree, and interim qdiscs would need to remember
to propagate the value.

Instead, reverse the responsibility: child qdiscs can ask their parent what
their TC and priomap are. ETS / PRIO know the answer right away, or there
are defaults for when the root qdisc does not assign them (e.g. when RED is
used as root qdisc). When RED and TBF become classful, they will simply
forward the request up to their parent.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As another qdisc is linked to the TBF, the latter should issue an event to
give drivers a chance to react to the grafting. In other qdiscs, this event
is called GRAFT, so follow suit with TBF as well.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

mlx5-updates-2021-10-18

Maor Maor Gottlieb says:
========================
Use hash to select the affinity port in VF LAG

Current VF LAG architecture is based on QP association with a port.
QP must be created after LAG is enabled to allow association with non-native port.
VM Packets going on slow-path to eSwicth manager (SW path or hairpin) will be transmitted
through a different QP than the VM. This means that Different packets of the same flow might
egress from different physical ports.

This patch-set solves this issue by moving the port selection to be based on the hash function
defined by the bond.

When the device is moved to VF LAG mode, the driver creates TTC (traffic type classifier) flow
tables in order to classify the packet and steer it to the relevant hash function. Similar to what
is done in the mlx5 RSS implementation.

Each rule in the TTC table, forwards the packet to port selection flow table which has one hash
split flow group which contains two "catch all" flow table entries. Each entry point to the
relative uplink port. As shown below:

		-------------------
		| FT              |
TTC rule ->	|     ----------- |
		|   FG|   FTE --|-|-----> uplink of port #1
		|     |   FTE --|-|-----> uplink of port #2
		|     ----------- |
		-------------------

Hash split flow group is flow group that created as type of HASH_SPLIT and associated with match definer.
The match definer define the fields which included in the hash calculation.

The driver creates the match definer according to the xmit hash policy of the bond driver.

Patches overview:
========================

Minor E-Switch updates:
- Patch #12, dynamic  allocation of dest array
- Patch #13, increase number of forward destinations to 32
Signed-off-by: David S. Miller <davem@davemloft.net>

Mateusz Palczewski says:

====================
40GbE Intel Wired LAN Driver Updates 2021-10-18

Use single state machine for driver initialization
and for service initialized driver. The init state
machine implemented in init_task() is merged
into the watchdog_task(). The init_task() function
is removed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Increase supported number of forward destinations in the same rule, local
and remote, from 2 to 32.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Use dynamic allocation for the dest array in preparation for
the next patch which increase MLX5_MAX_FLOW_FWD_VPORTS and
will cause stack allocation to be bigger than 1024 bytes.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Use the steering based solution for select the affinity port
when the LAG mode is based on hash policy and the device support
in port selection flow table.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add create function, build the steering tables, TTC and definers
according to the LAG hash type.

The destroy function, destroys all the steering components.

The modify functions is used when the bond mapping changes and it
iterates over all the rules in the definers and modifies them to steer
the packet to the relevant active ports.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add support to create inner and outer TTC tables for LAG port
selection. These tables are used to classify the packets in
order to select the related definer.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Every definer will consist of a flow table with a single hash group
with exactly two flow table entries, one for each device port.
The destination of these entries is the uplink vport according to the
port state and hash policy.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Set the related bits in the match definer mask according to the
TT mapping.
This mask will be used to create the match definers.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Generate a traffic type bitmap that will define which
steering objects we need to create for the steering
based LAG.

Bits in this bitmap are set according to the LAG hash type.
In addition, have a field that indicate if the lag is in encap
mode or not.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Downstream patches add another lag related file so it makes
sense to have all the lag files in a dedicated directory.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The uplink destination type should be used in rules to steer the
packet to the uplink when the device is in steering based LAG mode.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Introduce new APIs to create and destroy flow matcher
for given format id.

Flow match definer object is used for defining the fields and
mask used for the hash calculation. User should mask the desired
fields like done in the match criteria.

This object is assigned to flow group of type hash. In this flow
group type, packets lookup is done based on the hash result.

This patch also adds the required bits to create such flow group.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add new port selection flow steering namespace. Flow steering rules in
this namespaceare are used to determine the physical port for egress
packets.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add bitmasks to ttc_params to indicate if rule is valid or not.
It will allow to create TTC table with support only in part of the
traffic types.
In later patches which introduce the steering based LAG port selection,
TTC will be created with only part of the rules according to the hash
type.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Change the TCP common variable - "iscsi_ooo" to "ooo_opq".
This variable is common between all the TCP L5 protocols and not
specific to iSCSI.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Link: https://lore.kernel.org/r/20211015124118.29041-2-smalin@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Optimize the ll2 TCP out-of-order likely flows:
- Optimize the non-error flows of the ll2 ooo data path.
- Optimize "QED_OOO_RIGHT_BUF" over "QED_OOO_LEFT_BUF".
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Link: https://lore.kernel.org/r/20211015124118.29041-1-smalin@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit e330fb14 ("of: net: move of_net under net/") moves of_net.c
to ./net/core/, but misses to adjust the reference to this file in
MAINTAINERS.

Hence, ./scripts/get_maintainer.pl --self-test=patterns complains:

   warning: no file matches    F:    drivers/of/of_net.c

Adjust the file entry after this file movement.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211016055815.14397-1-lukas.bulwahn@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use single state machine for driver initialization and for service
initialized driver. The init state machine implemented in init_task()
is merged into the watchdog_task(). The init_task() function is
removed.
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

This commit adds a new state, __IAVF_INIT_FAILED to the state machine.
From now on initialization functions report errors not by returning an
error value, but by changing the state to indicate that something went
wrong.
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Replace state changes of iavf state machine
with a method that also tracks the previous
state the machine was on.

This change is required for further work with
refactoring init and watchdog state machines.

Tracking of previous state would help us
recover iavf after failure has occurred.
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

mlx5_tout_ms() returns a u64, we can't directly divide it.
This is not a problem here, @timeout which is the value
that actually matters here is already a ulong, so this
implies storing return value of mlx5_tout_ms() on a ulong
should be fine.

This fixes:

  ERROR: modpost: "__udivdi3" [drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.ko] undefined!

Fixes: 32def412 ("net/mlx5: Read timeout values from DTOR")
Link: https://lore.kernel.org/r/20211018172608.1069754-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Everything except the first 32 bits was lost when the pause flags were
added. This makes the 50000baseCR2 mode flag (bit 34) not appear.

I have tested this with a 10G card (SFN5122F-R7) by modifying it to
return a non-legacy link mode (10000baseCR).
Signed-off-by: Erik Ekman <erik@kryo.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix delay settings applied to wrong cpu in parse_port_config. The delay
values is set to the wrong index as the cpu_port_index is incremented
too early. Start the cpu_port_index to -1 so the correct value is
applied to address also the case with invalid phy mode and not available
port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS updates for net-next

The following patchset contains Netfilter/IPVS for net-next:

1) Add new run_estimation toggle to IPVS to stop the estimation_timer
   logic, from Dust Li.

2) Relax superfluous dynset check on NFT_SET_TIMEOUT.

3) Add egress hook, from Lukas Wunner.

4) Nowadays, almost all hook functions in x_table land just call the hook
   evaluation loop. Remove remaining hook wrappers from iptables and IPVS.
   From Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Alvin Šipraga says:

====================
net: dsa: add support for RTL8365MB-VC

This series adds support for Realtek's RTL8365MB-VC, a 4+1 port
10/100/1000M Ethernet switch. The driver - rtl8365mb - was developed by
Michael Ramussen and myself.

This version of the driver is relatively slim, implementing only the
standalone port functionality and no offload capabilities. It is based
on a previous RFC series [1] from August, and the main difference is the
removal of some spurious VLAN operations. Otherwise I have simply
addressed most of the feedback. Please see the respective patches for
more detail.

In parallel I am working on offloading the bridge layer capabilities,
but I would like to get the basic stuff upstreamed as soon as possible.

v3 -> v4:
  - get irq before setting virq parents (fixes kernel test robot
    warning)
  - remove pad-to-72-bytes logic in tagger xmit (fixes DENG Qingfang's
    suggestion); no longer needed as we set CPU minimum RX size to 64
    bytes
  - use mutex to protect MIB counter access instead of a spinlock (fixes
    Jakub's feedback on v3 statistics refactoring)

v2 -> v3:
  - move IRQ setup earlier in probe per Florian's suggestion
  - fix compilation error on some archs due to FIELD_PREP use in v1
  - follow Jakub's suggestion and use the standard ethtool stats API;
    NOTE: new patch in the series for relevant DSA plumbing
  - following the stats change, it became apparent that the rtl8366
    helper library is no longer that helpful; scrap it and implement
    the ethtool ops specifically for this chip

v1 -> v2:
  - drop DSA port type checks during MAC configuration
  - use OF properties to configure RGMII TX/RX delay
  - don't set default fwd_offload_mark if packet is trapped to CPU
  - remove port mapping macros
  - update device tree bindings documentation with an example
  - cosmetic changes to the tagging driver using FIELD_* macros

[1] https://lore.kernel.org/netdev/20210822193145.1312668-1-alvin@pqrs.dk/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The RTL8365MB-VC ethernet switch controller has 4 internal PHYs for its
user-facing ports. All that is needed is to let the PHY driver core
pick up the IRQ made available by the switch driver.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a realtek-smi subdriver for the RTL8365MB-VC 4+1 port
10/100/1000M switch controller. The driver has been developed based on a
GPL-licensed OS-agnostic Realtek vendor driver known as rtl8367c found
in the OpenWrt source tree.

Despite the name, the RTL8365MB-VC has an entirely different register
layout to the already-supported RTL8366RB ASIC. Notwithstanding this,
the structure of the rtl8365mb subdriver is loosely based on the rtl8366rb
subdriver. Like the 'rb, it establishes its own irqchip to handle
cascaded PHY link status interrupts.

The RTL8365MB-VC switch is capable of offloading a large number of
features from the software, but this patch introduces only the most
basic DSA driver functionality. The ports always function as standalone
ports, with bridging handled in software.

One more thing. Realtek's nomenclature for switches makes it hard to
know exactly what other ASICs might be supported by this driver. The
vendor driver goes by the name rtl8367c, but as far as I can tell, no
chip actually exists under this name. As such, the subdriver is named
rtl8365mb to emphasize the potentially limited support. But it is clear
from the vendor sources that a number of other more advanced switches
share a similar register layout, and further support should not be too
hard to add given access to the relevant hardware. With this in mind,
the subdriver has been written with as few assumptions about the
particular chip as is reasonable. But the RTL8365MB-VC is the only
hardware I have available, so some further work is surely needed.
Co-developed-by: Michael Rasmussen <mir@bang-olufsen.dk>
Signed-off-by: Michael Rasmussen <mir@bang-olufsen.dk>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit implements a basic version of the 8 byte tag protocol used
in the Realtek RTL8365MB-VC unmanaged switch, which carries with it a
protocol version of 0x04.

The implementation itself only handles the parsing of the EtherType
value and Realtek protocol version, together with the source or
destination port fields. The rest is left unimplemented for now.

The tag format is described in a confidential document provided to my
company by Realtek Semiconductor Corp. Permission has been granted by
the vendor to publish this driver based on that material, together with
an extract from the document describing the tag format and its fields.
It is hoped that this will help future implementors who do not have
access to the material but who wish to extend the functionality of
drivers for chips which use this protocol.

In addition, two possible values of the REASON field are specified,
based on experiments on my end. Realtek does not specify what value this
field can take.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl8365mb is a new realtek-smi subdriver for the RTL8365MB-VC 4+1 port
10/100/1000M Ethernet switch controller. Its compatible string is
"realtek,rtl8365mb".
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move things around a little so that this tag driver is alphabetically
ordered. The Kconfig file is sorted based on the tristate text.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub pointed out that we have a new ethtool API for reporting device
statistics in a standardized way, via .get_eth_{phy,mac,ctrl}_stats.
Add a small amount of plumbing to allow DSA drivers to take advantage of
this when exposing statistics.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new EtherType ETH_P_REALTEK to the if_ether.h uapi header. The
EtherType 0x8899 is used in a number of different protocols from Realtek
Semiconductor Corp [1], so no general assumptions should be made when
trying to decode such packets. Observed protocols include:

  0x1 - Realtek Remote Control protocol [2]
  0x2 - Echo protocol [2]
  0x3 - Loop detection protocol [2]
  0x4 - RTL8365MB 4- and 8-byte switch CPU tag protocols [3]
  0x9 - RTL8306 switch CPU tag protocol [4]
  0xA - RTL8366RB switch CPU tag protocol [4]

[1] https://lore.kernel.org/netdev/CACRpkdYQthFgjwVzHyK3DeYUOdcYyWmdjDPG=Rf9B3VrJ12Rzg@mail.gmail.com/
[2] https://www.wireshark.org/lists/ethereal-dev/200409/msg00090.html
[3] https://lore.kernel.org/netdev/20210822193145.1312668-4-alvin@pqrs.dk/
[4] https://lore.kernel.org/netdev/20200708122537.1341307-2-linus.walleij@linaro.org/Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Building the VF and PF side of this driver differently, with one being
a loadable module and the other one built-in results in a link failure
for the common PTP driver:

ld.lld: error: undefined symbol: __this_module
>>> referenced by otx2_ptp.c
>>>               net/ethernet/marvell/octeontx2/nic/otx2_ptp.o:(otx2_ptp_init) in archive drivers/built-in.a
>>> referenced by otx2_ptp.c
>>>               net/ethernet/marvell/octeontx2/nic/otx2_ptp.o:(otx2_ptp_init) in archive drivers/built-in.a

Move the otx2_ptp.c code into a separate module that gets built for
both configurations, making it built-in if at least one of the other
two is built-in.

Fixes: 43510ef4 ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kunihiko Hayashi says:

====================
net: ethernet: ave: Introduce UniPhier NX1 SoC support

This series includes the patches to add basic support for new UniPhier NX1
SoC. NX1 SoC also has the same kinds of controls as the other UniPhier
SoCs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add basic support for UniPhier NX1 SoC. This includes a compatible string
and SoC-dependent data.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update AVE binding document for UniPhier NX1 SoC.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>