- 14 Dec, 2017 25 commits
-
-
Sean Young authored
This is done to further remove the lirc kernel api. Ensure that every fops checks for this. Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Sean Young authored
Since the only mode lirc devices can handle is raw IR, handle this in a plain kfifo. Remove lirc_buffer since this is no longer needed. Signed-off-by:
-
Sean Young authored
Calculate lirc features when necessary, and add LIRC_{S,G}ET_REC_MODE cases to ir_lirc_ioctl. This makes lirc_dev_fop_ioctl() unnecessary since all cases are already handled by ir_lirc_ioctl(). Signed-off-by: -
Sean Young authored
For some IR protocols, some scancode values not valid, i.e. they're part of a different protocol variant. Signed-off-by:
-
Sean Young authored
Ensure we reject an attempt to transmit invalid scancodes. Signed-off-by:
-
Sean Young authored
The lirc user interface exists as a raw decoder, which does not make much sense for transmit-only devices. In addition, we want to have lirc char devices for devices which do not use raw IR, i.e. scancode only devices. Note that rc-code, lirc_dev, ir-lirc-codec are now calling functions of each other, so they've been merged into one module rc-core to avoid circular dependencies. Since ir-lirc-codec no longer exists as separate codec module, there is no need for RC_DRIVER_IR_RAW_TX type drivers to call ir_raw_event_register(). Signed-off-by:
-
Sean Young authored
When sending scancodes, load the encoder if we need it. Signed-off-by:
-
Sean Young authored
If the lirc device supports it, set the carrier for the protocol. Signed-off-by:
-
Sean Young authored
This introduces a new lirc mode: scancode. Any device which can send raw IR can now also send scancodes. int main() { int mode, fd = open("/dev/lirc0", O_RDWR); mode = LIRC_MODE_SCANCODE; if (ioctl(fd, LIRC_SET_SEND_MODE, &mode)) { // kernel too old or lirc does not support transmit } struct lirc_scancode scancode = { .scancode = 0x1e3d, .rc_proto = RC_PROTO_RC5, }; write(fd, &scancode, sizeof(scancode)); close(fd); } The other fields of lirc_scancode must be set to 0. Note that toggle (rc5, rc6) and repeats (nec) are not implemented. Nor is there a method for holding down a key for a period. Signed-off-by: -
Sean Young authored
LIRCCODE is a lirc mode where a driver produces driver-dependent codes for receive and transmit. No driver uses this any more. The LIRC_GET_LENGTH ioctl was used for this mode only. Signed-off-by:
-
Sean Young authored
Now that lirc is no longer in the staging area, remove the entry. Signed-off-by:
-
Sean Young authored
The ir-kbd-i2c driver behaves like the lirc_zilog driver, except it can send raw IR and receives scancodes rather than lirccodes. The lirc_zilog driver only polls if the lirc chardev is opened; similarly the ir-kbd-i2c driver only polls if the corresponding input device is opened, or the lirc device. Polling is disabled during IR transmission through the mutex. The polling period is 402ms in the ir-kdb-i2c driver, and 260ms in the lirc_zilog driver. Signed-off-by:
-
Sean Young authored
This is a fix for commit 329d88da ("[media] media: i2c: Don't export ir-kbd-i2c module alias") that stopped the module from being loaded automagically. The problems described only affect the HD-PVR, so it should not affect other hardware; also if the module happens to be loaded, the i2c IR part of the HD-PVR will be enabled anyway. Fixes: 329d88da ("[media] media: i2c: Don't export ir-kbd-i2c module alias") Signed-off-by:
-
Sean Young authored
This code implements the transmitter which is currently implemented in the staging lirc_zilog driver. The new code does not need a signal database, iow. the haup-ir-blaster.bin firmware file is no longer needed, and the driver does not know anything about the keycodes in that file. Instead, the new driver can send raw IR, but the hardware is limited to few different lengths of pulse and spaces, so it is best to use generated IR rather than recorded IR. Signed-off-by:
-
Sean Young authored
These two devices ids are really just one device with multiple addresses. Probing becomes much simpler if we simply fold this into one i2c device with two address. Note that this breaks the lirc_zilog driver, however we will teach ir-kbd-i2c to do what lirc_zilog does in a later commit. Signed-off-by:
-
Sean Young authored
The lirc_zilog driver only polls the device if the lirc chardev is opened; do the same with the rc-core driver. Signed-off-by:
-
Sean Young authored
Use the dev_dbg dynamic infrastructure instead of rolling our own custom debug logic. Signed-off-by:
-
Sean Young authored
With the parent set for the rc device, the messages clearly state that it is attached via i2c. The additional printk is unnecessary. These are the old messages: rc rc1: i2c IR (Hauppauge WinTV PVR-150 as /devices/virtual/rc/rc1 ir-kbd-i2c: i2c IR (Hauppauge WinTV PVR-150 detected at i2c-10/10-0071/ir0 [ivtv i2c driver #0] Now we simply get: rc rc1: Hauppauge WinTV PVR-150 as /devices/pci0000:00/0000:00:1e.0/0000:02:00.0/i2c-10/10-0071/rc/rc1 Note that we no longer copy the name. I've checked all call sites to verfiy this is not a problem. Signed-off-by:
-
Akinobu Mita authored
When iterating through all endpoints using of_graph_get_next_endpoint(), the refcount of the returned endpoint node is incremented and the refcount of the node which is passed as previous endpoint is decremented. So the caller doesn't need to call of_node_put() for each iterated node except for error exit paths. Otherwise we get "OF: ERROR: Bad of_node_put() on ..." messages. Cc: Hyun Kwon <hyun.kwon@xilinx.com> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Christophe JAILLET authored
This is odd to call 'pci_disable_device()' in an error path before a coresponding successful 'pci_enable_device()'. Return directly instead. Fixes: 77e0be12 ("V4L/DVB (4176): Bug-fix: Fix memory overflow") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Colin Ian King authored
Currently a user can pass in an unsanitized slot number which will lead to and out of range index into ca->slot_info. Fix this by checking that the slot number is no more than the allowed maximum number of slots. Seems that this bug has been in the driver forever. Detected by CoverityScan, CID#139381 ("Untrusted pointer read") Signed-off-by:Colin Ian King <colin.king@canonical.com> Reviewed-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Jasmin Jessich <jasmin@anw.at> Signed-off-by:
-
Gustavo A. R. Silva authored
Add suffix ULL to constant 65535 in order to avoid a potential integer overflow. This constant is used in a context that expects an expression of type u64. Addresses-Coverity-ID: 1056806 Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Stefan Brüns authored
Mygica T230 DVB-T/T2/C USB stick support. It uses the same FX2/Si2168 bridge/demodulator combo as the other devices supported by the driver, but uses the Si2141 tuner. Several DVB-T (MPEG2) and DVB-T2 (H.265) channels were tested, as well as the included remote control. Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by:
-
Dmitry Osipenko authored
NVIDIA Tegra20/30/114/124/132 SoC's have video decoder engine that supports standard set of video formats like H.264 / MPEG-4 / WMV / VC1. Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Dmitry Osipenko authored
Add binding documentation for the Video Decoder Engine which is found on NVIDIA Tegra20/30/114/124/132 SoC's. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
- 13 Dec, 2017 15 commits
-
-
Daniel Scheller authored
This change makes sure that demod frontends are always detached whenever a tuner frontend attach failed. Achieve this by moving the detach-on- failure logic at the end of dvb_input_attach(), and adding a goto to this block on every tuner attach failure case, so if an error occurs, there are no stray attached frontends left. As a side effect, this removes some duplicated code. Signed-off-by:
Daniel Scheller <d.scheller@gmx.net> Signed-off-by:
-
Pravin Shedge authored
These duplicate includes have been found with scripts/checkincludes.pl but they have been removed manually to avoid removing false positives. Signed-off-by:
Pravin Shedge <pravin.shedge4linux@gmail.com> Signed-off-by:
-
Benjamin Gaignard authored
Add SPDX identifiers to files under sti directory Signed-off-by:
Benjamin Gaignard <benjamin.gaignard@st.com> Reviewed-by:
Fabien Dessenne <fabien.dessenne@st.com> Acked-by:
Philippe Ombredanne <pombredanne@nexb.com> Acked-by:
Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by:
-
Jaedon Shin authored
The dtv_properties structure and the dtv_property structure are different sizes in 32-bit and 64-bit system. This patch provides FE_SET_PROPERTY and FE_GET_PROPERTY ioctl commands implementation for 32-bit user space applications. Signed-off-by:
Jaedon Shin <jaedon.shin@gmail.com> Signed-off-by:
-
Jaedon Shin authored
Adds compat_ioctl for 32-bit user space applications on a 64-bit system. [m.chehab@osg.samsung.com: add missing include compat.h] Signed-off-by:
-
Jaedon Shin authored
Adds unlocked ioctl function directly in dvb_frontend.c instead of using dvb_generic_ioctl(). Signed-off-by:
-
Wolfgang Rohdewald authored
dvb_frontend will call dvb_detach for: - stb0899_detach in dvb_frontend_release and - stb0899_release in __dvb_frontend_free But we only do dvb_attach(stb0899_attach). Increment the module refcount instead. Signed-off-by:
Wolfgang Rohdewald <wolfgang@rohdewald.de> Signed-off-by:
-
Fengguang Wu authored
drivers/media/dvb-core/dvb_frontend.c:154:2-7: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values. NULL check before some freeing functions is not needed. Based on checkpatch warning "kfree(NULL) is safe this check is probably not required" and kfreeaddr.cocci by Julia Lawall. Generated by: scripts/coccinelle/free/ifnullfree.cocci Fixes: b1cb7372 ("dvb_frontend: don't use-after-free the frontend struct") Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
-
Daniel Scheller authored
Since nothing from dvb_math.h is used, remove the unneeded include. Signed-off-by:
-
Daniel Scheller authored
tracking_optimization() doesn't make use of the symbol rate reported by the demodulator, so remove the unneeded inquiry and the now unneeded variable. Reported-by:
Richard Scobie <rascobie@slingshot.co.nz> Cc: Ralph Metzler <rjkm@metzlerbros.de> Signed-off-by:
-
Daniel Scheller authored
Utilise get_cur_symbol_rate() in get_frontend() to update the dtv_frontend_properties with the current symbol rate as reported by the demodulator. Reported-by:
-
Daniel Scheller authored
The result (if any) isn't used anywhere besides being assigned to a local variable (and the only current companion stv6111 doesn't even implement get_if_frequency()), thus remove the ptr check and the call, and also remove the now unused iffreq variable. Reported-by:
-
Daniel Scheller authored
When a parent (demod) driver encounters and signals a problem with gate_ctrl(), don't blindly continue poking the I2C bus. Signed-off-by:
-
Daniel Scheller authored
Stack dump when gate_ctrl() is called in a way that consecutive unlocks happen. This is a clear indication that other drivers interfacing with the stv0910 driver don't do things properly or don't check for failures, so dump stack so that those drivers can be identified and fixed. Signed-off-by:
-
Daniel Scheller authored
Each field (FSTV0910_XX) is declared as reg/off/unused/sign/mask. Add the missing offset value to the defines. Picked up from dddvb master, commit 8a1f27c3d22c ("add field offset to field defines") by Ralph Metzler <rjkm@metzlerbros.de>, adapted to match the comment style in the mainline driver. Cc: Ralph Metzler <rjkm@metzlerbros.de> Signed-off-by:
-
