- 05 Apr, 2023 11 commits
-
-
Alexander Stein authored
There is no need to require non-sleeping GPIO access. Silence the WARN_ON() if GPIO is using e.g. I2C expanders. Signed-off-by:
Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
AngeloGioacchino Del Regno authored
Add a panel entry with delay_200_500_e50 for the AUO NE135FBM-N41 version 8.1, found on a number of ACER laptops, including the Swift 3 (SF313-52, SF313-53), Chromebook Spin 513 (CP513-2H) and others. Signed-off-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by:
-
Pin-yen Lin authored
The default hpd_wait_us in panel_edp.c is 2 seconds. This makes the sleep time in the polling of _ps8640_wait_hpd_asserted become 200ms. Change it to a constant 20ms to speed up the function. Signed-off-by:
Pin-yen Lin <treapking@chromium.org> Reviewed-by:
Robert Foss <rfoss@kernel.org> Signed-off-by:
-
Marek Vasut authored
Do not generate the HS front and back porch gaps, the HSA gap and EOT packet, as per "SN65DSI83 datasheet SLLSEC1I - SEPTEMBER 2012 - REVISED OCTOBER 2020", page 22, these packets are not required. This makes the TI SN65DSI83 bridge work with Samsung DSIM on i.MX8MN. Signed-off-by:
Marek Vasut <marex@denx.de> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Luca Ceresoli authored
The LDB driver currently checks whether dual mode is used, otherwise it assumes only channel 0 is in use. Add support for using only channel 1. In device tree terms, this means linking port 2 only. Doing this cleanly requires changing the logic of the probe functions from this: 1. use of_graph_get_remote_node() on port 1 to find the panel 2. use drm_of_lvds_get_dual_link_pixel_order() to detect dual mode to this: 1. use of_graph_get_remote_node() twice to find remote ports 2. reuse the result of the above to know whether each channel is enabled and to find the panel 3. if (both channels as enabled) use drm_of_lvds_get_dual_link_pixel_order() to detect dual mode Also add a dev_dbg() to log the detected mode and log an error in case no panel was found (no channel enabled). Signed-off-by:Luca Ceresoli <luca.ceresoli@bootlin.com> Reviewed-by:
-
Luca Ceresoli authored
dev_warn() and similar require a training \n. Signed-off-by:
-
Alexander Stein authored
There might be cases where the host attach is deferred, use dev_err_probe to add more detailed information to /sys/kernel/debug/devices_deferred. Signed-off-by:
-
Karol Wachowski authored
VPU on MTL has hardware optimizations and does not require 10ms D0 - D3hot transition delay imposed by PCI specification (PCIe r6.0, sec 5.9.) . The delay removal is traditionally done by adding PCI ID to quirk_remove_d3hot_delay() in drivers/pci/quirks.c . But since we do not need that optimization before driver probe and we can better specify in the ivpu driver on what (future) hardware use the optimization, we do not use quirk_remove_d3hot_delay() for that. Signed-off-by:
Karol Wachowski <karol.wachowski@linux.intel.com> Signed-off-by:
Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Reviewed-by:
Jeffrey Hugo <quic_jhugo@quicinc.com> Signed-off-by:
Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230403121545.2995279-1-stanislaw.gruszka@linux.intel.com
-
Qiang Yu authored
This reverts commit bccafec9. This is due to the depend commit has been reverted on upstream: commit baad1097 ("Revert "drm/scheduler: track GPU active time per entity"") Acked-by:
Emil Velikov <emil.l.velikov@gmail.com> Signed-off-by:
Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230404002601.24136-4-yq882255@163.com
-
Qiang Yu authored
This reverts commit 87767de8. This is due to the depend commit has been reverted on upstream: commit baad1097 ("Revert "drm/scheduler: track GPU active time per entity"") Acked-by:
-
Qiang Yu authored
This reverts commit 4a66f3da. This is due to the depend commit has been reverted on upstream: commit baad1097 ("Revert "drm/scheduler: track GPU active time per entity"") Acked-by:
-
- 04 Apr, 2023 5 commits
-
-
Rob Clark authored
This should fix a crash that was reported on ast (and possibly other drivers which do not initialize vblank). fbcon: Taking over console Unable to handle kernel NULL pointer dereference at virtual address 0000000000000074 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004 CM = 0, WnR = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=0000080009d16000 [0000000000000074] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] SMP Modules linked in: ip6table_nat tun nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 rfkill ip_set nf_tables nfnetlink qrtr sunrpc binfmt_misc vfat fat xfs snd_usb_audio snd_hwdep snd_usbmidi_lib snd_seq snd_pcm snd_rawmidi snd_timer snd_seq_device snd soundcore joydev mc ipmi_ssif ipmi_devintf ipmi_msghandler arm_spe_pmu arm_cmn arm_dsu_pmu arm_dmc620_pmu cppc_cpufreq loop zram crct10dif_ce polyval_ce nvme polyval_generic ghash_ce sbsa_gwdt igb nvme_core ast nvme_common i2c_algo_bit xgene_hwmon gpio_dwapb scsi_dh_rdac scsi_dh_emc scsi_dh_alua ip6_tables ip_tables dm_multipath fuse CPU: 12 PID: 469 Comm: kworker/12:1 Not tainted 6.3.0-rc2-00008-gd39e48ca #1 Hardware name: ADLINK AVA Developer Platform/AVA Developer Platform, BIOS TianoCore 2.04.100.07 (SYS: 2.06.20220308) 09/08/2022 Workqueue: events fbcon_register_existing_fbs pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : drm_crtc_next_vblank_start+0x2c/0x98 lr : drm_atomic_helper_wait_for_fences+0x90/0x240 sp : ffff80000d583960 x29: ffff80000d583960 x28: ffff07ff8fc187b0 x27: 0000000000000000 x26: ffff07ff99c08c00 x25: 0000000000000038 x24: ffff07ff99c0c000 x23: 0000000000000001 x22: 0000000000000038 x21: 0000000000000000 x20: ffff07ff9640a280 x19: 0000000000000000 x18: ffffffffffffffff x17: 0000000000000000 x16: ffffb24d2eece1c0 x15: 0000003038303178 x14: 3032393100000048 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : ffffb24d2eeeaca0 x8 : ffff80000d583628 x7 : 0000080077783000 x6 : 0000000000000000 x5 : ffff80000d584000 x4 : ffff07ff99c0c000 x3 : 0000000000000130 x2 : 0000000000000000 x1 : ffff80000d5839c0 x0 : ffff07ff99c0cc08 Call trace: drm_crtc_next_vblank_start+0x2c/0x98 drm_atomic_helper_wait_for_fences+0x90/0x240 drm_atomic_helper_commit+0xb0/0x188 drm_atomic_commit+0xb0/0xf0 drm_client_modeset_commit_atomic+0x218/0x280 drm_client_modeset_commit_locked+0x64/0x1a0 drm_client_modeset_commit+0x38/0x68 __drm_fb_helper_restore_fbdev_mode_unlocked+0xb0/0xf8 drm_fb_helper_set_par+0x44/0x88 fbcon_init+0x1e0/0x4a8 visual_init+0xbc/0x118 do_bind_con_driver.isra.0+0x194/0x3a0 do_take_over_console+0x50/0x70 do_fbcon_takeover+0x74/0xf8 do_fb_registered+0x13c/0x158 fbcon_register_existing_fbs+0x78/0xc0 process_one_work+0x1ec/0x478 worker_thread+0x74/0x418 kthread+0xec/0x100 ret_from_fork+0x10/0x20 Code: f9400004 b9409013 f940a082 9ba30a73 (b9407662) ---[ end trace 0000000000000000 ]--- v2: Use drm_dev_has_vblank() Reported-by:Nathan Chancellor <nathan@kernel.org> Fixes: d39e48ca ("drm/atomic-helper: Set fence deadline for vblank") Signed-off-by:
Rob Clark <robdclark@chromium.org> Reviewed-by:
Thomas Zimmermann <tzimmermann@suse.de> Tested-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20230403160314.1210533-1-robdclark@gmail.com
-
Daniel Vetter authored
It's not exactly the same since the open coded version doesn't set primary correctly. But that's a bugfix, so shouldn't hurt really. Signed-off-by:
-
Daniel Vetter authored
It exists! Note that since this is an exact copy, there shouldn't be any functional difference here. Signed-off-by:
-
Daniel Vetter authored
It's just open coded and matches. Note that Thomas said that his version apparently failed for some reason, but hey maybe we should try again. Signed-off-by:
-
Sui Jingfeng authored
EFI FB, VESA FB or VGA FB etc belong to firmware based framebuffer driver. Signed-off-by:
Sui Jingfeng <suijingfeng@loongson.cn> Reviewed-by:
Javier Martinez Canillas <javierm@redhat.com> Signed-off-by:
-
- 03 Apr, 2023 5 commits
-
-
Marek Vasut authored
The VS signal change is synchronized to HS signal change, start the info graphics with that event, instead of having that event occur in the middle of it. Scope trace of DPI bus with HS/VS active HIGH looks as follows: ________________...__ VS...___/__ __ \______... HS...___/ \_______/ \__...__/ \___... ^ ^ | | | Used to start here -' | '--- Start info graphics here Signed-off-by:Sam Ravnborg <sam@ravnborg.org> Acked-by:
Rob Herring <robh@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230221200407.16531-1-marex@denx.de
-
Marek Vasut authored
The TC358767/TC358867/TC9595 are capable of DSI burst mode, which is more energy efficient than the non-burst modes. Make use of it. The TC358767/TC358867/TC9595 are capable of DSI non-continuous clock, since it sources the internal PLL clock from external clock source. The DSI non-continuous clock further reduces power utilization. The TC358767/TC358867/TC9595 may use DSI LPM for command transmissions, make sure this is configured correctly in the DSI mode flags. Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20221016003632.406468-1-marex@denx.de
-
Simon Ser authored
We don't populate drm_driver.gem_prime_import_sg_table so only DMA-BUFs exported from our own device can be imported. We don't populate drm_gem_object_funcs.get_sg_table so DMA-BUFs cannot be imported into another device. Still, this is useful to user-space to share buffers between processes and between API boundaries (e.g. wlroots hard-requires PRIME import/export support). v2: expand commit message Signed-off-by:
Simon Ser <contact@emersion.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Tian Tao <tiantao6@hisilicon.com> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Hans de Goede <hdegoede@redhat.com> Acked-by:
Christian König <christian.koenig@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230302143502.500661-2-contact@emersion.fr
-
Simon Ser authored
drm_gem_map_dma_buf() requires drm_gem_object_funcs.get_sg_table to be implemented, or else WARNs. Allow drivers to leave this hook unimplemented to implement purely local DMA-BUFs (ie, DMA-BUFs which cannot be imported anywhere else but the device which allocated them). In that case, reject imports to other devices in drm_gem_map_attach(). v2: new patch v3: use ENOSYS Signed-off-by:
-
Francesco Dolcini authored
LT8912 DSI port supports only Non-Burst mode video operation with Sync Events and continuous clock on clock lane, correct dsi mode flags according to that removing MIPI_DSI_MODE_VIDEO_BURST flag. Cc: <stable@vger.kernel.org> Fixes: 30e2ae94 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge") Signed-off-by:
Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by:
-
- 02 Apr, 2023 4 commits
-
-
Erico Nunes authored
This exposes an accumulated active time per client via the fdinfo infrastructure per execution engine, following Documentation/gpu/drm-usage-stats.rst. In lima, the exposed execution engines are gp and pp. Signed-off-by:
Erico Nunes <nunes.erico@gmail.com> Signed-off-by:
-
Erico Nunes authored
To track if fds are pointing to the same execution context and export the expected information to fdinfo, similar to what is done in other drivers. Signed-off-by:
-
Erico Nunes authored
lima maintains a context manager per drm_file, similar to amdgpu. In order to account for the complete usage per drm_file, all of the associated contexts need to be considered. Previously released contexts also need to be accounted for but their drm_sched_entity info is gone once they get released, so account for it in the ctx_mgr. Signed-off-by:
-
Harshit Mogalapalli authored
Smatch reports: drivers/gpu/drm/lima/lima_drv.c:396 lima_pdev_probe() warn: missing unwind goto? Store return value in err and goto 'err_out0' which has lima_sched_slab_fini() before returning. Fixes: a1d2a633 ("drm/lima: driver for ARM Mali4xx GPUs") Signed-off-by:
Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Signed-off-by:
-
- 31 Mar, 2023 7 commits
-
-
Krzysztof Kozlowski authored
Panels are supposed to have one port (defined in panel-common.yaml binding) and can have also rotation: rk3326-odroid-go3.dtb: panel@0: 'port', 'rotation' do not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by:
Jagan Teki <jagan@amarulasolutions.com> Link: https://lore.kernel.org/r/20230326204224.80181-4-krzysztof.kozlowski@linaro.orgSigned-off-by:
-
Krzysztof Kozlowski authored
Panels are supposed to have one port (defined in panel-common.yaml binding) and can have also rotation: rk3326-odroid-go2.dtb: panel@0: 'port', 'rotation' do not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
Panels are supposed to have one port (defined in panel-common.yaml binding): rk3399-rockpro64.dtb: panel@0: 'port' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
Panels are supposed to have one port (defined in panel-common.yaml binding): px30-evb.dtb: panel@0: 'port' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The device comes with DCX pin which is already used in canaan/sipeed_maixduino.dts (although not in Linux driver). Signed-off-by:
-
AngeloGioacchino Del Regno authored
Some SoCs implementing ARM Mali GPUs are subject to speed binning: this means that some versions of the same SoC model may need to be limited to a slower frequency compared to the other: this is being addressed by reading nvmem (usually, an eFuse array) containing a number that identifies the speed binning of the chip, which is usually related to silicon quality. To address such situation, add basic support for reading the speed-bin through nvmem, as to make it possible to specify the supported hardware in the OPP table for GPUs. This commit also keeps compatibility with any platform that does not specify (and does not even support) speed-binning. Signed-off-by:
Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by:
-
AngeloGioacchino Del Regno authored
Some SoCs implementing ARM Mali GPUs may be subject to speed binning and the usable bin is read from nvmem: document the addition of nvmem and nvmem-cells for 'speed-bin'. Signed-off-by:
-
- 30 Mar, 2023 3 commits
-
-
Rob Herring authored
It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. Convert reading boolean properties to of_property_read_bool(). Reviewed-by:
-
Fabio Estevam authored
Marco's NXP email is no longer valid. Marco told me offline that he has no interest to be listed as the maintainer contact for this binding, so add my contact. Signed-off-by:
Fabio Estevam <festevam@denx.de> Acked-by:
-
Maarten Lankhorst authored
Backmerge to get rc4. Signed-off-by:Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
-
- 29 Mar, 2023 5 commits
-
-
Krzysztof Kozlowski authored
Allow 'rotation' property (coming from panel-common.yaml) already used in DTS: sc7180-trogdor-quackingstick-r0.dtb: panel@0: 'rotation' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
Panels are supposed to have one reg. This fixes dtbs_check warnings like: sc7180-idp.dtb: panel@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
Panels are supposed to have one port (coming from panel-common.yaml binding): msm8916-samsung-a3u-eur.dtb: panel@0: 'port' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
Few panels like Samsung s6e3fc2x01 and sofef00 use vddio-supply instead of power-supply (in DTS and Linux driver), so allow it to fix: sdm845-oneplus-enchilada.dtb: panel@0: 'power-supply' is a required property Signed-off-by:
-
Krzysztof Kozlowski authored
The nt36672a bindings were added with a mistake on VDDIO supply calling it in one place vddio and in other vddi0. Typical name is rather vddio which is also now used by DTS (sdm845-xiaomi-beryllium-common.dtsi) and Linux driver. Fixes: c2abcf30 ("dt-bindings: display: novatek,nt36672a: Fix unevaluated properties warning") Fixes: 9528a024 ("dt-bindings: display: panel: Add bindings for Novatek nt36672a") Signed-off-by:
-
