The scripts/dtc/checks.c requires that the node have empty "dma-ranges"
property must have the same "#address-cells" and "#size-cells" values as
the parent node. Otherwise, the following warnings is reported:

arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \
(dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \
its #address-cells (1) differs from / (2)
arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \
(dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \
its #size-cells (1) differs from / (2)

Arnd Bergmann figured out why it's necessary:
Also note that the #address-cells=<1> means that any device under
this bus is assumed to only support 32-bit addressing, and DMA will
have to go through a slow swiotlb in the absence of an IOMMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201016090833.1892-3-thunder.leizhen@huawei.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

The modem firmware memory requirements vary between 32M/140M on
no-lte/lte skus respectively, so fixup the modem memory region
to reflect the requirements.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1602786476-27833-1-git-send-email-sibis@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add the camera clock controller node supported on SC7180.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1604687907-25712-1-git-send-email-tdas@codeaurora.org
[bjorn: Dropped camcc include]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Set the qcom,adreno-smmu compatible string for the GPU SMMU to enable
split pagetables and per-instance pagetables for drm/msm.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200905200454.240929-21-robdclark@gmail.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Set the qcom,adreno-smmu compatible string for the GPU SMMU to enable
split pagetables and per-instance pagetables for drm/msm.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201109184728.2463097-5-jcrouse@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

We want userspace to represent the human perceived brightness.
Since the led drivers and the leds themselves don't have a
linear response to the value we give them in terms of perceived
brightness, we'll bake the curve into the dts.

The panel also doesn't have a good response under 5%, so we'll avoid
sending it anything lower than that.

Note: Ideally this patch should be coupled with the driver change from
"backlight: pwm_bl: Fix interpolation", but it can work without it,
without looking too ugly.
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Alexandru Stan <amstan@chromium.org>
Link: https://lore.kernel.org/r/20201021220404.v3.2.Ie4d84af5a85e8dcb8f575845518fa39f324a827d@changeidSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Populate Venus DT node with interconnect properties.
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Link: https://lore.kernel.org/r/20201102113529.16152-1-stanimir.varbanov@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Enable PMIC's RTC device on SM8250-MTP board.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201103005432.1181832-2-dmitry.baryshkov@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Enable PMIC's RTC device on RB5 board.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201103005432.1181832-1-dmitry.baryshkov@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add the soc-specific compatible string so that it can be matched
more specifically now that the driver cares which SoC it's on.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201028172737.v3.2.Ia3b68ac843df93c692627a3a92b947b3a5785863@changeidSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

As talked about in the patch ("arm64: dts: qcom: sc7180: Provide
pinconf for SPI to use GPIO for CS"), on some boards it makes much
more sense (and is much more efficient) to think of the SPI Chip
Select as a GPIO.  Trogdor is one such board where the SPI parts don't
run in GSI mode and we do a lot of SPI traffic.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20200921142655.v3.2.I3c57d8b6d83d5bdad73a413eea1e249a98d11973@changeidSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

When the chip select line is controlled by the QUP, changing CS is a
time consuming operation.  We have to send a command over to the geni
and wait for it to Ack us every time we want to change (both making it
high and low).  To send this command we have to make a choice in
software when we want to control the chip select, we have to either:
A) Wait for the Ack via interrupt which slows down all SPI transfers
   (and incurrs extra processing associated with interrupts).
B) Sit in a loop and poll, waiting for the Ack.

Neither A) nor B) is a great option.

We can avoid all of this by realizing that, at least on some boards,
there is no advantage of considering this line to be a geni line.
While it's true that geni _can_ control the line, it's also true that
the line can be a GPIO and there is no downside of viewing it that
way.  Setting a GPIO is a simple MMIO operation.

This patch provides definitions so a board can easily select the GPIO
mode.

NOTE: apparently, it's possible to run the geni in "GSI" mode.  In GSI
the SPI port is allowed to be controlled by more than one user (like
firmware and Linux) and also the port can operate sequences of
operations in one go.  In GSI mode it _would_ be invalid to look at
the chip select as a GPIO because that would prevent other users from
using it.  In theory GSI mode would also avoid some overhead by
allowing us to sequence the chip select better.  However, I'll argue
GSI is not relevant for all boards (and certainly not any boards
supported by mainline today).  Why?
- Apparently to run a SPI chip in GSI mode you need to initialize it
  (in the bootloader) with a different firmware and then it will
  always run in GSI mode.  Since there is no support for GSI mode in
  the current Linux driver, it must be that existing boards don't have
  firmware that's doing that.  Note that the kernel device tree
  describes hardware but also firmware, so it is legitimate to make
  the assumption that we don't have GSI firmware in a given dts file.
- Some boards with sc7180 have SPI connected to the Chrome OS EC or
  security chip (Cr50).  The protocols for talking to cros_ec and cr50
  are extremely complex.  Both drivers in Linux fully lock the bus
  across several distinct SPI transfers.  While I am not an expert on
  GSI mode it feels highly unlikely to me that we'd ever be able to
  enable GSI mode for these devices.

From a testing perspective, running "flashrom -p ec -r /tmp/foo.bin"
in a loop after this patch shows almost no reduction in time, but the
number of interrupts per command goes from 32357 down to 30611 (about
a 5% reduction).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20200921142655.v3.1.I997a428f58ef9d48b37a27a028360f34e66c00ec@changeidSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

s1 (VDDCX) and l3 (VDDMX) are now managed by rpmpd as power domains.
This allows us to vote for voltage corners instead of voting for raw
voltages. But we cannot manage these as regulator and power domain at
the same time: The votes by rpmpd would conflict with the ones from
the regulator driver.

All users of these regulators have been converted to power domains.
Make sure that no new users are added by removing s1 and l3 from
the regulator definitions.

This also allows us to remove the arbitrary voltage constraints
we have been using for these regulators. Not all of the voltages
listed there would actually have been safe for the boards.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200916104135.25085-11-stephan@gerhold.netSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

So far we have been making proxy votes for the remote processors
through the regulator interface. Now that we have rpmpd it's better
to vote for performance states through the power domain interface.

This also allows us to move these supplies back to msm8916.dtsi
because the device tree binding for RPMPD is independent of the
underlying regulator/PMIC.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200916104135.25085-10-stephan@gerhold.netSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

MSM8916 has two RPM power domains: VDDCX and VDDMX.
So far we have been managing them by voting for raw voltages through
the regulator subsystem, but it's better to manage them with corners
as actual power domains.

Add the device tree node for rpmpd so we can manage them as real
power domains instead of using the regulators.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200916104135.25085-5-stephan@gerhold.netSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

In commit e23b1220 ("arm64: dts: qcom: sc7180: Increase the number
of interconnect cells") we missed increasing the cells on one
interconnect.  That's no bueno.  Fix it.

NOTE: it appears that things aren't totally broken without this fix,
but clearly something isn't going to be working right.  If nothing
else, without this fix I see this in the logs:

  OF: /soc@0/mdss@ae00000: could not get #interconnect-cells for /soc@0/interrupt-controller@17a00000

Fixes: e23b1220 ("arm64: dts: qcom: sc7180: Increase the number of interconnect cells")
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201001141838.1.I08054d1d976eed64ffa1b0e21d568e0dc6040b54@changeidSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Memory region reserved for the TZ is changed long back. Let's
update the same to align with the corret region. Its size also
increased to 4MB from 2MB.

Along with that, bump the Q6 region size to 85MB.

Fixes: 1e827785 ("arm64: dts: Add ipq6018 SoC and CP01 board support")
Signed-off-by: Kathiravan T <kathirav@codeaurora.org>
Link: https://lore.kernel.org/r/1602690377-21304-1-git-send-email-kathirav@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

    https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.plSigned-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace".  So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 453431a5 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:
 "A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset

Pull scheduler fixes from Thomas Gleixner:
 "Two scheduler fixes:

   - A trivial build fix for sched_feat() to compile correctly with
     CONFIG_JUMP_LABEL=n

   - Replace a zero lenght array with a flexible array"

* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/features: Fix !CONFIG_JUMP_LABEL case
  sched: Replace zero-length array with flexible-array

Pull perf fix from Thomas Gleixner:
 "A single fix to compute the field offset of the SNOOPX bit in the data
  source bitmask of perf events correctly"

* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: correct SNOOPX field offset

Pull locking fix from Thomas Gleixner:
 "Just a trivial fix for kernel-doc warnings"

* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/seqlocks: Fix kernel-doc warnings

Pull NTB fixes from Jon Mason.

* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
  NTB: Use struct_size() helper in devm_kzalloc()
  ntb: intel: Fix memleak in intel_ntb_pci_probe
  NTB: hw: amd: fix an issue about leak system resources

Pull i2c fix from Wolfram Sang:
 "Regression fix for rc1 and stable kernels as well"

* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Pull more cifs updates from Steve French:
 "Add support for stat of various special file types (WSL reparse points
  for char, block, fifo)"

* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  smb3: add some missing definitions from MS-FSCC
  smb3: remove two unused variables
  smb3: add support for stat of WSL reparse points for special file types

Pull more parisc updates from Helge Deller:

 - During this merge window O_NONBLOCK was changed to become 000200000,
   but we missed that the syscalls timerfd_create(), signalfd4(),
   eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
   bit-wise check of the flags parameter.

   To provide backward compatibility with existing userspace we
   introduce parisc specific wrappers for those syscalls which filter
   out the old O_NONBLOCK value and replaces it with the new one.

 - Prevent HIL bus driver to get stuck when keyboard or mouse isn't
   attached

 - Improve error return codes when setting rtc time

 - Minor documentation fix in pata_ns87415.c

* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  ata: pata_ns87415.c: Document support on parisc with superio chip
  parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
  hil/parisc: Disable HIL driver when it gets stuck
  parisc: Improve error return codes when setting rtc time

Pull more xen updates from Juergen Gross:

 - a series for the Xen pv block drivers adding module parameters for
   better control of resource usge

 - a cleanup series for the Xen event driver

* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  Documentation: add xen.fifo_events kernel parameter description
  xen/events: unmask a fifo event channel only if it was masked
  xen/events: only register debug interrupt for 2-level events
  xen/events: make struct irq_info private to events_base.c
  xen: remove no longer used functions
  xen-blkfront: Apply changed parameter name to the document
  xen-blkfront: add a parameter for disabling of persistent grants
  xen-blkback: add a parameter for disabling of persistent grants

Pull SafeSetID updates from Micah Morton:
 "The changes are mostly contained to within the SafeSetID LSM, with the
  exception of a few 1-line changes to change some ns_capable() calls to
  ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
  is examined by SafeSetID code and nothing else in the kernel.

  The changes to SafeSetID internally allow for setting up GID
  transition security policies, as already existed for UIDs"

* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
  LSM: SafeSetID: Fix warnings reported by test bot
  LSM: SafeSetID: Add GID security policy handling
  LSM: Signal to SafeSetID when setting group IDs

Pull random32 updates from Willy Tarreau:
 "Make prandom_u32() less predictable.

  This is the cleanup of the latest series of prandom_u32
  experimentations consisting in using SipHash instead of Tausworthe to
  produce the randoms used by the network stack.

  The changes to the files were kept minimal, and the controversial
  commit that used to take noise from the fast_pool (f227e3ec) was
  reverted. Instead, a dedicated "net_rand_noise" per_cpu variable is
  fed from various sources of activities (networking, scheduling) to
  perturb the SipHash state using fast, non-trivially predictable data,
  instead of keeping it fully deterministic. The goal is essentially to
  make any occasional memory leakage or brute-force attempt useless.

  The resulting code was verified to be very slightly faster on x86_64
  than what is was with the controversial commit above, though this
  remains barely above measurement noise. It was also tested on i386 and
  arm, and build- tested only on arm64"

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/

* tag '20201024-v4-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/prandom:
  random32: add a selftest for the prandom32 code
  random32: add noise from network and scheduling activity
  random32: make prandom_u32() output unpredictable

Commit 21653a41 ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().

But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().

Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.

This fixes the Microsoft Surface Go 2 hanging at boot.

Fixes: 21653a41 ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Pull block fixes from Jens Axboe:

 - NVMe pull request from Christoph
     - rdma error handling fixes (Chao Leng)
     - fc error handling and reconnect fixes (James Smart)
     - fix the qid displace when tracing ioctl command (Keith Busch)
     - don't use BLK_MQ_REQ_NOWAIT for passthru (Chaitanya Kulkarni)
     - fix MTDT for passthru (Logan Gunthorpe)
     - blacklist Write Same on more devices (Kai-Heng Feng)
     - fix an uninitialized work struct (zhenwei pi)"

 - lightnvm out-of-bounds fix (Colin)

 - SG allocation leak fix (Doug)

 - rnbd fixes (Gioh, Guoqing, Jack)

 - zone error translation fixes (Keith)

 - kerneldoc markup fix (Mauro)

 - zram lockdep fix (Peter)

 - Kill unused io_context members (Yufen)

 - NUMA memory allocation cleanup (Xianting)

 - NBD config wakeup fix (Xiubo)

* tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block: (27 commits)
  block: blk-mq: fix a kernel-doc markup
  nvme-fc: shorten reconnect delay if possible for FC
  nvme-fc: wait for queues to freeze before calling update_hr_hw_queues
  nvme-fc: fix error loop in create_hw_io_queues
  nvme-fc: fix io timeout to abort I/O
  null_blk: use zone status for max active/open
  nvmet: don't use BLK_MQ_REQ_NOWAIT for passthru
  nvmet: cleanup nvmet_passthru_map_sg()
  nvmet: limit passthru MTDS by BIO_MAX_PAGES
  nvmet: fix uninitialized work for zero kato
  nvme-pci: disable Write Zeroes on Sandisk Skyhawk
  nvme: use queuedata for nvme_req_qid
  nvme-rdma: fix crash due to incorrect cqe
  nvme-rdma: fix crash when connect rejected
  block: remove unused members for io_context
  blk-mq: remove the calling of local_memory_node()
  zram: Fix __zram_bvec_{read,write}() locking order
  skd_main: remove unused including <linux/version.h>
  sgl_alloc_order: fix memory leak
  lightnvm: fix out-of-bounds write to array devices->info[]
  ...

Pull io_uring fixes from Jens Axboe:

 - fsize was missed in previous unification of work flags

 - Few fixes cleaning up the flags unification creds cases (Pavel)

 - Fix NUMA affinities for completely unplugged/replugged node for io-wq

 - Two fallout fixes from the set_fs changes. One local to io_uring, one
   for the splice entry point that io_uring uses.

 - Linked timeout fixes (Pavel)

 - Removal of ->flush() ->files work-around that we don't need anymore
   with referenced files (Pavel)

 - Various cleanups (Pavel)

* tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  splice: change exported internal do_splice() helper to take kernel offset
  io_uring: make loop_rw_iter() use original user supplied pointers
  io_uring: remove req cancel in ->flush()
  io-wq: re-set NUMA node affinities if CPUs come online
  io_uring: don't reuse linked_timeout
  io_uring: unify fsize with def->work_flags
  io_uring: fix racy REQ_F_LINK_TIMEOUT clearing
  io_uring: do poll's hash_node init in common code
  io_uring: inline io_poll_task_handler()
  io_uring: remove extra ->file check in poll prep
  io_uring: make cached_cq_overflow non atomic_t
  io_uring: inline io_fail_links()
  io_uring: kill ref get/drop in personality init
  io_uring: flags-based creds init in queue

Pull libata fixes from Jens Axboe:
 "Two minor libata fixes:

   - Fix a DMA boundary mask regression for sata_rcar (Geert)

   - kerneldoc markup fix (Mauro)"

* tag 'libata-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  ata: fix some kernel-doc markups
  ata: sata_rcar: Fix DMA boundary mask

Pull misc vfs updates from Al Viro:
 "Assorted stuff all over the place (the largest group here is
  Christoph's stat cleanups)"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: remove KSTAT_QUERY_FLAGS
  fs: remove vfs_stat_set_lookup_flags
  fs: move vfs_fstatat out of line
  fs: implement vfs_stat and vfs_lstat in terms of vfs_fstatat
  fs: remove vfs_statx_fd
  fs: omfs: use kmemdup() rather than kmalloc+memcpy
  [PATCH] reduce boilerplate in fsid handling
  fs: Remove duplicated flag O_NDELAY occurring twice in VALID_OPEN_FLAGS
  selftests: mount: add nosymfollow tests
  Add a "nosymfollow" mount option.

Pull dma-mapping fixes from Christoph Hellwig:

 - document the new dma_{alloc,free}_pages() API

 - two fixups for the dma-mapping.h split

* tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: document dma_{alloc,free}_pages
  dma-mapping: move more functions to dma-map-ops.h
  ARM/sa1111: add a missing include of dma-map-ops.h

Pull KVM fixes from Paolo Bonzini:
 "Two fixes for this merge window, and an unrelated bugfix for a host
  hang"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: ioapic: break infinite recursion on lazy EOI
  KVM: vmx: rename pi_init to avoid conflict with paride
  KVM: x86/mmu: Avoid modulo operator on 64-bit value to fix i386 build