- [DVB] reafactor or add the following frontend drivers: at76c651, cx22700,
  ves1x93, ves1820, tda80xx, tda8083, cx22702, tda1004x, tda10021, cx24110,
  dvb_dummy_fe, l64781, mt312, mt352, stv0299, sp887x, stv0297, nxt6000,
  sp8870

- [DVB] remove dib3000mb from frontends, it's handled by the hw dependent
  driver now
Signed-off-by: Michael Hunold <hunold@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

- [DVB] get_dvb_firmware: rework to reflect new frontend design, added
  additional firmware location

- [DVB] Kconfig and Makefile changes all over the place, remove Makefile.lib
Signed-off-by: Michael Hunold <hunold@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Start of a big DVB update.


The reasons for revamping the DVB frontend architecture:

Just as analog TV cards, DVB cards need some sort of tuner to tune to the
desired frequency of the digital transponder.  Tuning alone doesn't give you a
digital DVB datastream, however, you need a demodulator as well.  The
combination of tuner and demodulator is called frontend in the DVB world.
Tuner and demodulator are both accessed via the serial i2c bus on all DVB
cards out there.  So, technically a frontend consists of two i2c helper
chipsets.

In former times when there was only a handful of different DVB cards, the
frontend was encapsulated in one tin box.  Some people had the idea that there
should be one "frontend driver" instead of dedicated tuner and demodulator
drivers.  A bad idea.

As time went on, different manufacturers used the same tuner and demodulator
combination, but used a different wiring for the tuner or did other technical
changes.  The only possibility to support different cards with one combined
frontend driver was to add hardware dependent tuner code inside the generic
i2c frontend drivers.  Yuck.

So there was a need for communication between the i2c frontend driver and the
hardware depenedent driver, for example to exchange initialization code for
the tuner.  Unfortunately, the i2c infrastructure is one way, from the i2c
client to the i2c adapter using a non-typesafe ioctl() like interface, which
is ugly by itself.  Greg K-H and others refused the idea to add an iotctl()
like interface from the i2c adapter to the i2c client and instead proposed to
use a typesafe interface instead.  We all agreed with that.

The existing i2c infrastructure heavily depends on the probing facility, ie.
clients probe for their existence on i2c busses.  This is dumb for most i2c
busses out there that sit on dedicated hardware.  A DVB card is uniquely
identified with pci or usb subvendor and subsystem ids, so on that particular
bus we exactly *know* which kinds of i2c helper chipsets sit on there.

Up to now this wasn't a problem, because we could fix all conflicts manually
until half a year ago.  By that date, we found two different DVB designs which
used different demodulators that unfortunately use the same i2c address and
which cannot be distinguished by hardware tricks (ie.  different number of
registers, some fixed hw dependent register,...)

Getting a usable DVB card depended on the load order of the modules, because
the i2c core probed the demodulator drivers one after another and the first
one won the race.  Compiling all drivers statically into the kernel resulted
in non-working cards.

Our solution is as follows: we agreed to keep the basic underlying kernel i2c
infrastructure, but we decided not to register our bussed and chipsets to the
kernel i2c "probing" infrastructure.  Instead, we killed the tuner parts of
the frontend drivers and put them into the dedicated hardware drivers (this is
were they technically belong, they are highly hardware dependent) and we
changed the frontend drivers to pure demodulator drivers (which are hardware
independend).  There is now a type-safe functional dependency between the
drivers and the demodulator drivers, the drivers explicitely ask the
demodulator drivers to attach to their i2c bus.  The only negative aspect of
that approach is that for some hardware there are now more dependencies to
demodulator drivers than needed, ie.  a small amount of memory is wasted.

This patch:

- [DVB] cards.txt: added the USB devices to the card-list
- [DVB] README.dibusb: follow changes in dibusb-driver
Signed-off-by: Michael Hunold <hunold@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Heh. usually these come through Andrew, but this time it was all me.

Noted by BenH.

Cset exclude: paulus@samba.org[torvalds]|ChangeSet|20041207181541|44524

In 2.6.8 the code for the BLKRRPART ioctl was changed
to return EIO when no partitions were found, such as
on an empty disk. This breaks some partitioning programs
and is also confusing: "Input/Output error" while in fact
nothing was wrong with this brand new all blank disk.

This restores old behaviour.

Self explanatory.. Based on a report on l/k
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

We recently found a problem that was causing memory corruption during
boot on IBM POWER5 machines.  The problem was that the if you have a
USB keyboard and it is set to the input device for the firmware, it
will still be active when the kernel is started.  That means that the
OHCI controller has pointers to various memory areas that it polls for
transfers to do.  When we start using that same memory in the kernel,
bad things can happen.  (This isn't a problem on powermacs because the
Apple OF implements a "quiesce" call which turns off all the devices
it is using.)

This patch fixes the problem by calling the Open Firmware "close"
method for the input device.  Stephen Rothwell and I have verified
that doing this fixes the problem on the POWER5 machine where we
observed it.  I verified that this patch doesn't cause any problems on
powermacs.

I think this patch should go into 2.6.10 since it fixes a nasty memory
corruption bug that can cause rather subtle and hard-to-diagnose
problems during boot.  (The symptom on the POWER5 machine with the
particular kernel that we were using was that reading /proc/net/tcp
would oops, due to one of the pointers in tcp_ehash being corrupted.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

alloc_dma_rcv_ctx is called in interrupt and Kernel Spinlock debugging code
cribs about it via "Debug: sleeping function called in interrupt context". 
See sample stack traces below.

The patch below corrects ohci1394.c to use GFP_ATOMIC instead of
GFP_KERNEL.  Tested to work fine with 2 different Camcorder devices for
fairly long periods and connect/disconnects.
Signed-off-by: Parag Warudkar <kernel-stuff@comcast.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The patch adds the definition vm_private_data again to
snd_pcm_lib_mmap_iomem().  It got lost during the rewrite of the mmap
stuff.
Signed-off-by: Martin Langer <martin-langer@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

pci_disable_device() is called properly in the removal and error paths. 
Also, the pci_set_master() is added to the resume callbacks if missing
(just to be sure).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Fixed the sleep in spinlock during prepare callback.  This happened only on
Nforce chips.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The PCI IRQ map for the old Motorola PowerStackII (Utah) boards was
incorrect, but this breakage wasn't exposed until 2.5, and finally fixed
until recently by Sebastian Heutling <sheutlin@gmx.de>.
Signed-off-by: Christian Kujau <evil@g-house.de>
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patches fixes the return code from cciss_ioctl.  Without this some
block layer (BLK*) ioctls do not work.

Thanks to Jens Axboe for pointing this out.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

We recently found a problem that was causing memory corruption during boot
on IBM POWER5 machines.  The problem was that the if you have a USB
keyboard and it is set to the input device for the firmware, it will still
be active when the kernel is started.  That means that the OHCI controller
has pointers to various memory areas that it polls for transfers to do. 
When we start using that same memory in the kernel, bad things can happen. 
(This isn't a problem on powermacs because the Apple OF implements a
"quiesce" call which turns off all the devices it is using.)

This patch fixes the problem by calling the Open Firmware "close" method
for the input device.  Stephen Rothwell and I have verified that doing this
fixes the problem on the POWER5 machine where we observed it.  I verified
that this patch doesn't cause any problems on powermacs.

I think this patch should go into 2.6.10 since it fixes a nasty memory
corruption bug that can cause rather subtle and hard-to-diagnose problems
during boot.  (The symptom on the POWER5 machine with the particular kernel
that we were using was that reading /proc/net/tcp would oops, due to one of
the pointers in tcp_ehash being corrupted.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Fix eepro100 driver suspend/resume issue.

Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Current cfq can cause hangs with non-fs requests, because the accounting
goes bad.  This fixes it.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

M68k: Update defconfigs for 2.6.10-rc3
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The D-Link DGE-528T gigabit adapter is based on the 8169 chipset (reported
by Andreas Tauscher <ta@lonestar-bbs.de>, checked in the sources of a
driver for this adapter).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The isolcpus option is broken in 2.6.10-rc2-bk2.  The domains are no longer
being properly initialized (which results in a panic at bootup).
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The PowerMac specific sleep code in the OHCI USB driver used to call
disable/enable irq, which is no longer necessary and actually clashes with
the calls to free/request_irq that the common OHCI code now does, thus
causing WARN_ON's to trigger each time a PowerBook is woken up from sleep.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

If given no-hlt kernel option, ia32 idle loop turns out to be a spin loop. 
Add cpu_relax() in this spin loop because IA32 SDM recommends that a PAUSE
instruction be put in all spin loops.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

There's a chance that the receive buffers are being consumed at the same
rate as they are being replenished in ibmveth_replenish_task()... 
Meanwhile, the calls to schedule_replenishing() from ibmveth_poll() won't
schedule another replenishing cycle (because the not_replenishing flag is
zero), starving the buffers and making the adapter unable to receive
packets unless the module is reloaded...  Here's a small patch that will
fix it by scheduling another replenishing task after toggling the
not_replenishing flag.
Signed-Off-By: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Fix the non-normalized wall_to_monotonic for i386 and m32r (The other archs
seem to get it right)
Signed-off-by: Herbert Poetzl <herbert@13thfloor.at>
Signed-off-by: George Anzinger <george@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Patch from David Vrabel

Fix a minor typo in the MODULE_AUTHOR string in ixp4xx_wdt.

Signed-off-by: David Vrabel
Signed-off-by: Russell King

Patch from Marc Singer

Add support for the LPD7a40x implementation of the SMC91x ethernet
controller. This patch exists to work around a mismatch between the
way the LH7a40x CPUs handle chip selects and what the ethernet
controller expects.

This patch has been revised to eliminate masking of interrupts.  The
concessions are that 

  a) the ISR must perform an IOBARRIER before the first access to the
     chip, just in case the interrupt occurred while the driver was
     writing to the chip
  b) other drivers that use the same chip select region as the SMC
     chip must perform a similar IOBARRIER at the top of their ISRs.

Signed-off-by: Marc Singer
Signed-off-by: Russell King

Patch from Marc Singer

A missing exten prevented the 2.6.10-rc2 kernel from building for the
LPD7A404.  This patch adds it.

Signed-off-by: Marc Singer
Signed-off-by: Russell King

Patch from Holger Hans Peter Freyther

As proposed in 2282 asm-arm/arch-sa1100/ide.h is not included anymore from asm-arm/ide.h. 
If arch-sa1100/ide.h is included we abort with #error.
If lart.c is compiled we kindly warn that ide needs fixing for this board.


Signed-off-by: Holger Hans Peter Freyther
Signed-off-by: Russell King

Patch from Marc Singer

Some typos prevent the 2.6.10-rc2 kernel from building for the
LPD7A400.  This patch fixes them.  It also removes CONFIG_FIQ which
shouldn't be necessary and doesn't compile.

Signed-off-by: Marc Singer
Signed-off-by: Russell King

Some time ago, a patch was merged that removed pci_save_state() and
pci_restore_state() from various ALSA drivers. That patch also added
pci_restore_state() to sound/core/init.c but didn't add pci_save_state()
anywhere. This is needed since the core pci handling doesn't do this for
us anymore.

My laptop doesn't resume (gets what I assume is an ACPI timeout and
hangs solid) without this small obvious patch.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Fixed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Use milliseconds internally for these delays, and convert them
to centiseconds at the interface boundary to the ioctl
configuration controls.

into ppc970.osdl.org:/home/torvalds/v2.6/linux

We have to load the bigkernel second TLB entry on
secondary processors before we move over the use
the kernel trap table.  Otherwise we can take a
TLB miss somewhere in the post-4MB area and the
TLB handler is not prepared to service that.

The case that usually occurs is the prom_set_trap_table
call made by trampoline.S, since p1275buf usually sits
very near the end of the kernel image.  It worked by
luck most of the time as long as p1275buf sits within
a single page since earlier code running in trampoline.S
forced that TLB entry to be loaded by the OBP TLB miss
handler.

This was not fun to figure out.
Signed-off-by: David S. Miller <davem@davemloft.net>

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Always pass values to get_user and put_user in an even numbered
register, and optionally the next odd numbered register.  This
ensures that we are compatible with compiler enhancements.

Patch from Ben Dooks

A simple divide is not enough for the s3c2410 default
timer code, due to most clocks not being a nice multiple
of usecs.

This update changes the calculation of the usec to use
multipliers and shifts to effect a fast divide by a non-integer
number.

Original patch by Dimitry Andric, updated by Ben Dooks

Signed-off-by: Dimitry Andric

Signed-off-by: Ben Dooks
Signed-off-by: Russell King

Ok, here we go (finally).  A patch to correct the cut-and-paste
copyright in arch/ia64/kernel/domain.c.  Both Silicon Graphics, Inc. 
and myself (yes personally) hold the copyright on this file.
Signed-off-by: Jesse Barnes <jbarnes@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>