- 28 Jul, 2014 22 commits
-
-
Niu Yawei authored
commit d68aab6b upstream. Commit 1ab6c499 (fs: convert fs shrinkers to new scan/count API) accidentally removed locking from quota shrinker. Fix it - dqcache_shrink_scan() should use dq_list_lock to protect the scan on free_dquots list. Fixes: 1ab6c499Signed-off-by:
Niu Yawei <yawei.niu@intel.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Stefan Assmann authored
commit 76252723 upstream. To properly re-initialize SR-IOV it is necessary to reset the device even if it is already down. Not doing this may result in Tx unit hangs. Signed-off-by:
Stefan Assmann <sassmann@kpanic.de> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Todd Fujinaka authored
commit 94826487 upstream. On some devices, the internal PLL circuit occasionally provides the wrong clock frequency after power up. The probability of failure is less than one failure per 1000 power cycles. When the failure occurs, the internal clock frequency is around 1/20 of the correct frequency. Signed-off-by:
Todd Fujinaka <todd.fujinaka@intel.com> Tested-by:
-
Guenter Roeck authored
commit de12d6f4 upstream. Temperature limit registers are signed. Limits therefore need to be clamped to (-128, 127) degrees C and not to (0, 255) degrees C. Without this fix, writing a limit of 128 degrees C sets the actual limit to -128 degrees C. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Reviewed-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
-
Axel Lin authored
commit ee14b644 upstream. Dashes are not allowed in hwmon name attributes. Use "da9052" instead of "da9052-hwmon". Signed-off-by:
-
Axel Lin authored
commit 6b00f440 upstream. Dashes are not allowed in hwmon name attributes. Use "da9055" instead of "da9055-hwmon". Signed-off-by:
-
David Vrabel authored
commit fb9a0c44 upstream. Since cd9151e2 (xen/balloon: set a mapping for ballooned out pages), a ballooned out page had its entry in the p2m set to the MFN of one of the scratch pages. This means that the p2m will contain many entries pointing to the same MFN. During a domain save, these many-to-one entries are not identified as such and the scratch page is saved multiple times. On restore the ballooned pages are populated with new frames and the domain may use up its allocation before all pages can be restored. Since the original fix only needed to keep a mapping for the ballooned page it is safe to set ballooned out pages as INVALID_P2M_ENTRY in the p2m (as they were before). Thus preventing them from being saved and re-populated on restore. Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Reported-by:
Marek Marczykowski <marmarek@invisiblethingslab.com> Tested-by:
Stefano Stabellini <stefano.stabellini@eu.citrix.com> Signed-off-by:
-
zhangwei(Jovi) authored
commit f0160a5a upstream. The TRACE_ITER_PRINTK check in __trace_puts/__trace_bputs is missing, so add it, to be consistent with __trace_printk/__trace_bprintk. Those functions are all called by the same function: trace_printk(). Link: http://lkml.kernel.org/p/51E7A7D6.8090900@huawei.comSigned-off-by:
zhangwei(Jovi) <jovi.zhangwei@huawei.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
zhangwei(Jovi) authored
commit 8abfb872 upstream. Currently trace option stacktrace is not applicable for trace_printk with constant string argument, the reason is in __trace_puts/__trace_bputs ftrace_trace_stack is missing. In contrast, when using trace_printk with non constant string argument(will call into __trace_printk/__trace_bprintk), then trace option stacktrace is workable, this inconstant result will confuses users a lot. Link: http://lkml.kernel.org/p/51E7A7C9.9040401@huawei.comSigned-off-by:
-
Steven Rostedt (Red Hat) authored
commit 5f8bf2d2 upstream. Running my ftrace tests on PowerPC, it failed the test that checks if function_graph tracer is affected by the stack tracer. It was. Looking into this, I found that the update_function_graph_func() must be called even if the trampoline function is not changed. This is because archs like PowerPC do not support ftrace_ops being passed by assembly and instead uses a helper function (what the trampoline function points to). Since this function is not changed even when multiple ftrace_ops are added to the code, the test that falls out before calling update_function_graph_func() will miss that the update must still be done. Call update_function_graph_function() for all calls to update_ftrace_function() Signed-off-by:
-
Oleg Nesterov authored
commit 2448e349 upstream. instance_rmdir() path destroys the event files but forgets to free file->filter. Change remove_event_file_dir() to free_event_filter(). Link: http://lkml.kernel.org/p/20140711190638.GA19517@redhat.com Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: Tom Zanussi <tom.zanussi@linux.intel.com> Cc: "zhangwei(Jovi)" <jovi.zhangwei@huawei.com> Fixes: f6a84bdc "tracing: Introduce remove_event_file_dir()" Signed-off-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
-
Srinivas Pandruvada authored
commit 78b33216 upstream. When event spec is shared by multiple channels, which has definition for mask_shared_by_type, iio_device_register_eventset fails. For example: static const struct iio_event_spec iio_dummy_events[] = { { .type = IIO_EV_TYPE_THRESH, .dir = IIO_EV_DIR_RISING, .mask_separate = BIT(IIO_EV_INFO_ENABLE), .mask_shared_by_type = BIT(IIO_EV_INFO_VALUE), }, { .type = IIO_EV_TYPE_THRESH, .dir = IIO_EV_DIR_FALLING, .mask_separate = BIT(IIO_EV_INFO_ENABLE),a .mask_shared_by_type = BIT(IIO_EV_INFO_VALUE), } }; If two channels use this event spec, this will result in error. This change handles EBUSY error similar to iio_device_add_info_mask_type(). Signed-off-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Anand Avati authored
commit 154210cc upstream. The following test case demonstrates the bug: sh# mount -t glusterfs localhost:meta-test /mnt/one sh# mount -t glusterfs localhost:meta-test /mnt/two sh# echo stuff > /mnt/one/file; rm -f /mnt/two/file; echo stuff > /mnt/one/file bash: /mnt/one/file: Stale file handle sh# echo stuff > /mnt/one/file; rm -f /mnt/two/file; sleep 1; echo stuff > /mnt/one/file On the second open() on /mnt/one, FUSE would have used the old nodeid (file handle) trying to re-open it. Gluster is returning -ESTALE. The ESTALE propagates back to namei.c:filename_lookup() where lookup is re-attempted with LOOKUP_REVAL. The right behavior now, would be for FUSE to ignore the entry-timeout and and do the up-call revalidation. Instead FUSE is ignoring LOOKUP_REVAL, succeeding the revalidation (because entry-timeout has not passed), and open() is again retried on the old file handle and finally the ESTALE is going back to the application. Fix: if revalidation is happening with LOOKUP_REVAL, then ignore entry-timeout and always do the up-call. Signed-off-by:
Anand Avati <avati@redhat.com> Reviewed-by:
Niels de Vos <ndevos@redhat.com> Signed-off-by:
Miklos Szeredi <mszeredi@suse.cz> Signed-off-by:
-
Miklos Szeredi authored
commit 233a01fa upstream. If the number in "user_id=N" or "group_id=N" mount options was larger than INT_MAX then fuse returned EINVAL. Fix this to handle all valid uid/gid values. Signed-off-by:
-
Miklos Szeredi authored
commit 126b9d43 upstream. As suggested by checkpatch.pl, use time_before64() instead of direct comparison of jiffies64 values. Signed-off-by:
-
Loic Poulain authored
commit 48439d50 upstream. When detecting a non-link packet, h5_reset_rx() frees the Rx skb. Not returning after that will cause the upcoming h5_rx_payload() call to dereference a now NULL Rx skb and trigger a kernel oops. Signed-off-by:
Loic Poulain <loic.poulain@intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
K. Y. Srinivasan authored
commit 9bd2d0df upstream. Add code to poll the channel since we process only one message at a time and the host may not interrupt us. Also increase the receive buffer size since some KVP messages are close to 8K bytes in size. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Signed-off-by:
-
Mengdong Lin authored
commit caaf5ef9 upstream. This patch initialized the local audio InfoFrame variable 'ai' to be all zero, thus the data bytes will indicate "Refer to Stream Header" by default. Signed-off-by:
Mengdong Lin <mengdong.lin@intel.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 4da63c6f upstream. When the initialization of Intel HDMI controller fails due to missing i915 kernel symbols (e.g. HD-audio is built in while i915 is module), the driver discontinues the probe. However, since the probe was done asynchronously, the driver object still remains, thus the relevant PM ops are still called at suspend/resume. This results in the bad access to the incomplete audio card object, eventually leads to Oops or stall at PM. This patch adds the missing checks of chip->init_failed flag at each PM callback in order to fix the problem above. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79561Signed-off-by:
-
Hans de Goede authored
commit 242841d3 upstream. Tested-and-reported-by:
yullaw <yullaw@mageia.cz> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by:
-
Abbas Raza authored
commit 953c6646 upstream. There are 2 methods for ZLP (zero-length packet) generation: 1) In software 2) Automatic generation by device controller 1) is implemented in UDC driver and it attaches ZLP to IN packet if descriptor->size < wLength 2) can be enabled/disabled by setting ZLT bit in the QH When gadget ffs is connected to ubuntu host, the host sends get descriptor request and wLength in setup packet is 255 while the size of descriptor which will be sent by gadget in IN packet is 64 byte. So the composite driver sets req->zero = 1. In UDC driver following code will be executed then if (hwreq->req.zero && hwreq->req.length && (hwreq->req.length % hwep->ep.maxpacket == 0)) add_td_to_list(hwep, hwreq, 0); Case-A: So in case of ubuntu host, UDC driver will attach a ZLP to the IN packet. ubuntu host will request 255 byte in IN request, gadget will send 64 byte with ZLP and host will come to know that there is no more data. But hold on, by default ZLT=0 for endpoint 0 so hardware also tries to automatically generate the ZLP which blocks enumeration for ~6 seconds due to endpoint 0 STALL, NAKs are sent to host for any requests (OUT/PING) Case-B: In case when gadget ffs is connected to Apple device, Apple device sends setup packet with wLength=64. So descriptor->size = 64 and wLength=64 therefore req->zero = 0 and UDC driver will not attach any ZLP to the IN packet. Apple device requests 64 bytes, gets 64 bytes and doesn't further request for IN data. But ZLT=0 by default for endpoint 0 so hardware tries to automatically generate the ZLP which blocks enumeration for ~6 seconds due to endpoint 0 STALL, NAKs are sent to host for any requests (OUT/PING) According to USB2.0 specs: 8.5.3.2 Variable-length Data Stage A control pipe may have a variable-length data phase in which the host requests more data than is contained in the specified data structure. When all of the data structure is returned to the host, the function should indicate that the Data stage is ended by returning a packet that is shorter than the MaxPacketSize for the pipe. If the data structure is an exact multiple of wMaxPacketSize for the pipe, the function will return a zero-length packet to indicate the end of the Data stage. In Case-A mentioned above: If we disable software ZLP generation & ZLT=0 for endpoint 0 OR if software ZLP generation is not disabled but we set ZLT=1 for endpoint 0 then enumeration doesn't block for 6 seconds. In Case-B mentioned above: If we disable software ZLP generation & ZLT=0 for endpoint then enumeration still blocks due to ZLP automatically generated by hardware and host not needing it. But if we keep software ZLP generation enabled but we set ZLT=1 for endpoint 0 then enumeration doesn't block for 6 seconds. So the proper solution for this issue seems to disable automatic ZLP generation by hardware (i.e by setting ZLT=1 for endpoint 0) and let software (UDC driver) handle the ZLP generation based on req->zero field. Signed-off-by:
Abbas Raza <Abbas_Raza@mentor.com> Signed-off-by:
Peter Chen <peter.chen@freescale.com> Signed-off-by:
-
Gavin Guo authored
commit bb86cf56 upstream. When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller [1022:7814], the second hotplugging will experience the USB 3.0 pen drive is recognized as high-speed device. After bisecting the kernel, I found the commit number 41e7e056 (USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing some experiments, the bug can be fixed by avoiding executing the function hub_usb3_port_disable(). Because the port status with [AMD] FCH USB XHCI Controlleris [1022:7814] is already in RxDetect (I tried printing out the port status before setting to Disabled state), it's reasonable to check the port status before really executing hub_usb3_port_disable(). Fixes: 41e7e056 (USB: Allow USB 3.0 ports to be disabled.) Signed-off-by:
Gavin Guo <gavin.guo@canonical.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
- 17 Jul, 2014 18 commits
-
-
Greg Kroah-Hartman authored
-
Lan Tianyu authored
commit 75646e75 upstream. Some machines (eg. Lenovo Z480) ECs are not stable during boot up and causes battery driver fails to be loaded due to failure of getting battery information from EC sometimes. After several retries, the operation will work. This patch is to retry to get battery information 5 times if the first try fails. [ backport to 3.14.5: removed second parameter in acpi_battery_update(), introduced by the commit 9e50bc14 (ACPI / battery: Accelerate battery resume callback)] [naszar <naszar@ya.ru>: backport to 3.14.5] Link: https://bugzilla.kernel.org/show_bug.cgi?id=75581Reported-and-tested-by:
naszar <naszar@ya.ru> Cc: All applicable <stable@vger.kernel.org> Signed-off-by:
Lan Tianyu <tianyu.lan@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Roland Dreier authored
commit c81c8a1e upstream. In __ioremap_caller() (the guts of ioremap), we loop over the range of pfns being remapped and checks each one individually with page_is_ram(). For large ioremaps, this can be very slow. For example, we have a device with a 256 GiB PCI BAR, and ioremapping this BAR can take 20+ seconds -- sometimes long enough to trigger the soft lockup detector! Internally, page_is_ram() calls walk_system_ram_range() on a single page. Instead, we can make a single call to walk_system_ram_range() from __ioremap_caller(), and do our further checks only for any RAM pages that we find. For the common case of MMIO, this saves an enormous amount of work, since the range being ioremapped doesn't intersect system RAM at all. With this change, ioremap on our 256 GiB BAR takes less than 1 second. Signed-off-by:
Roland Dreier <roland@purestorage.com> Link: http://lkml.kernel.org/r/1399054721-1331-1-git-send-email-roland@kernel.orgSigned-off-by:
H. Peter Anvin <hpa@linux.intel.com> Signed-off-by:
-
Guenter Roeck authored
commit fb43e847 upstream. powerpc:allmodconfig has been failing for some time with the following error. arch/powerpc/kernel/exceptions-64s.S: Assembler messages: arch/powerpc/kernel/exceptions-64s.S:1312: Error: attempt to move .org backwards make[1]: *** [arch/powerpc/kernel/head_64.o] Error 1 A number of attempts to fix the problem by moving around code have been unsuccessful and resulted in failed builds for some configurations and the discovery of toolchain bugs. Fix the problem by disabling RELOCATABLE for COMPILE_TEST builds instead. While this is less than perfect, it avoids substantial code changes which would otherwise be necessary just to make COMPILE_TEST builds happy and might have undesired side effects. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Chen Gang authored
commit c863810c upstream. It is only a typo issue, the related commit: "1fbc4c4d drivers/rtc/rtc-puv3.c: use dev_dbg() instead of pr_debug()" The related error (unicore32 with allmodconfig): CC [M] drivers/rtc/rtc-puv3.o drivers/rtc/rtc-puv3.c: In function 'puv3_rtc_setpie': drivers/rtc/rtc-puv3.c:74: error: implicit declaration of function 'dev_debug' Signed-off-by:
Chen Gang <gang.chen.5i5j@gmail.com> Acked-by:
Xuetao Guan <gxt@mprc.pku.edu.cn> Signed-off-by:
-
Chen Gang authored
commit 73fa5406 upstream. It is only a typo issue, the related commit: "1fbc4c4d drivers/rtc/rtc-puv3.c: use dev_dbg() instead of pr_debug()" The related error (for unicore32 with allmodconfig): CC [M] drivers/rtc/rtc-puv3.o drivers/rtc/rtc-puv3.c: In function 'puv3_rtc_setalarm': drivers/rtc/rtc-puv3.c:143: error: 'struct device' has no member named 'dev' Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 8b8b3683 upstream. The per_cpu buffers are created one per possible CPU. But these do not mean that those CPUs are online, nor do they even exist. With the addition of the ring buffer polling, it assumes that the caller polls on an existing buffer. But this is not the case if the user reads trace_pipe from a CPU that does not exist, and this causes the kernel to crash. Simple fix is to check the cpu against buffer bitmask against to see if the buffer was allocated or not and return -ENODEV if it is not. More updates were done to pass the -ENODEV back up to userspace. Link: http://lkml.kernel.org/r/5393DB61.6060707@oracle.comReported-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Joonsoo Kim authored
commit fe8eea4f upstream. We should free memory for bitmap when we find zone mismatch, otherwise this memory will leak. Additionally, I copy code comment from PPC KVM's CMA code to inform why we need to check zone mis-match. Signed-off-by:
Joonsoo Kim <iamjoonsoo.kim@lge.com> Acked-by:
Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Reviewed-by:
Michal Nazarewicz <mina86@mina86.com> Reviewed-by:
Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Acked-by:
Minchan Kim <minchan@kernel.org> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Michal Nazarewicz <mina86@mina86.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: Alexander Graf <agraf@suse.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Ville Syrjälä authored
commit f1e1c212 upstream. On most gen2-4 platforms the GTT can be (or maybe always is?) inside the stolen memory region. If that's the case, reduce the size of the stolen memory appropriately to make make sure we don't clobber the GTT. v2: Deal with gen4 36 bit physical address Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80151Acked-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Christian König authored
commit 0986c1a5 upstream. When we set the valid bit on invalid GART entries they are loaded into the TLB when an adjacent entry is loaded. This poisons the TLB with invalid entries which are sometimes not correctly removed on TLB flush. For stable inclusion the patch probably needs to be modified a bit. Signed-off-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 6abafb78 upstream. Fixes hangs on driver load on some cards. bug: https://bugs.freedesktop.org/show_bug.cgi?id=76998Signed-off-by:
-
Alex Deucher authored
commit ed963771 upstream. Need to use the RREG32_SMC() accessor since the register is an smc indirect index. Signed-off-by:
-
Alexandre Demers authored
commit 41959341 upstream. It reverts commit c745fe61 now that Cayman is stable since VDDCI fix. Spread spectrum was not the culprit. This depends on b0880e87 (drm/radeon/dpm: fix vddci setup typo on cayman). Signed-off-by:
Alexandre Demers <alexandre.f.demers@gmail.com> Signed-off-by:
-
Theodore Ts'o authored
commit 3f1f9b85 upstream. This fixes the following lockdep complaint: [ INFO: possible circular locking dependency detected ] 3.16.0-rc2-mm1+ #7 Tainted: G O ------------------------------------------------------- kworker/u24:0/4356 is trying to acquire lock: (&(&sbi->s_es_lru_lock)->rlock){+.+.-.}, at: [<ffffffff81285fff>] __ext4_es_shrink+0x4f/0x2e0 but task is already holding lock: (&ei->i_es_lock){++++-.}, at: [<ffffffff81286961>] ext4_es_insert_extent+0x71/0x180 which lock already depends on the new lock. Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&ei->i_es_lock); lock(&(&sbi->s_es_lru_lock)->rlock); lock(&ei->i_es_lock); lock(&(&sbi->s_es_lru_lock)->rlock); *** DEADLOCK *** 6 locks held by kworker/u24:0/4356: #0: ("writeback"){.+.+.+}, at: [<ffffffff81071d00>] process_one_work+0x180/0x560 #1: ((&(&wb->dwork)->work)){+.+.+.}, at: [<ffffffff81071d00>] process_one_work+0x180/0x560 #2: (&type->s_umount_key#22){++++++}, at: [<ffffffff811a9c74>] grab_super_passive+0x44/0x90 #3: (jbd2_handle){+.+...}, at: [<ffffffff812979f9>] start_this_handle+0x189/0x5f0 #4: (&ei->i_data_sem){++++..}, at: [<ffffffff81247062>] ext4_map_blocks+0x132/0x550 #5: (&ei->i_es_lock){++++-.}, at: [<ffffffff81286961>] ext4_es_insert_extent+0x71/0x180 stack backtrace: CPU: 0 PID: 4356 Comm: kworker/u24:0 Tainted: G O 3.16.0-rc2-mm1+ #7 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 Workqueue: writeback bdi_writeback_workfn (flush-253:0) ffffffff8213dce0 ffff880014b07538 ffffffff815df0bb 0000000000000007 ffffffff8213e040 ffff880014b07588 ffffffff815db3dd ffff880014b07568 ffff880014b07610 ffff88003b868930 ffff88003b868908 ffff88003b868930 Call Trace: [<ffffffff815df0bb>] dump_stack+0x4e/0x68 [<ffffffff815db3dd>] print_circular_bug+0x1fb/0x20c [<ffffffff810a7a3e>] __lock_acquire+0x163e/0x1d00 [<ffffffff815e89dc>] ? retint_restore_args+0xe/0xe [<ffffffff815ddc7b>] ? __slab_alloc+0x4a8/0x4ce [<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0 [<ffffffff810a8707>] lock_acquire+0x87/0x120 [<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0 [<ffffffff8128592d>] ? ext4_es_free_extent+0x5d/0x70 [<ffffffff815e6f09>] _raw_spin_lock+0x39/0x50 [<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0 [<ffffffff8119760b>] ? kmem_cache_alloc+0x18b/0x1a0 [<ffffffff81285fff>] __ext4_es_shrink+0x4f/0x2e0 [<ffffffff812869b8>] ext4_es_insert_extent+0xc8/0x180 [<ffffffff812470f4>] ext4_map_blocks+0x1c4/0x550 [<ffffffff8124c4c4>] ext4_writepages+0x6d4/0xd00 ... Reported-by:
Theodore Ts'o <tytso@mit.edu> Reported-by:
-
Eric Sandeen authored
commit 5dd21424 upstream. The mount manpage says of the max_batch_time option, This optimization can be turned off entirely by setting max_batch_time to 0. But the code doesn't do that. So fix the code to do that. Signed-off-by:
Eric Sandeen <sandeen@redhat.com> Signed-off-by:
-
Theodore Ts'o authored
commit 94d4c066 upstream. We are spending a lot of time explaining to users what this error means. Let's try to improve the message to avoid this problem. Signed-off-by:
-
Theodore Ts'o authored
commit ae0f78de upstream. Make it clear that values printed are times, and that it is error since last fsck. Also add note about fsck version required. Signed-off-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
Andreas Dilger <adilger@dilger.ca> Signed-off-by:
-
Theodore Ts'o authored
commit 61c219f5 upstream. The first time that we allocate from an uninitialized inode allocation bitmap, if the block allocation bitmap is also uninitalized, we need to get write access to the block group descriptor before we start modifying the block group descriptor flags and updating the free block count, etc. Otherwise, there is the potential of a bad journal checksum (if journal checksums are enabled), and of the file system becoming inconsistent if we crash at exactly the wrong time. Signed-off-by:
-
