- 20 Dec, 2017 40 commits
-
-
weiping zhang authored
[ Upstream commit 658e9a6d ] /sys/class/scsi_disk/0:2:0:0/allow_restart can be changed to 0 unexpectedly by writing an invalid string such as the following: echo asdf > /sys/class/scsi_disk/0:2:0:0/allow_restart Signed-off-by:
weiping zhang <zhangweiping@didichuxing.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
weiping zhang authored
[ Upstream commit 623401ee ] /sys/class/scsi_disk/0:2:0:0/manage_start_stop can be changed to 0 unexpectly by writing an invalid string. Signed-off-by:
-
Jia-Ju Bai authored
[ Upstream commit 42c8eb3f ] The driver may sleep under a spinlock, and the function call path is: vt6655_suspend (acquire the spinlock) pci_set_power_state __pci_start_power_transition (drivers/pci/pci.c) msleep --> may sleep To fix it, pci_set_power_state is called without having a spinlock. This bug is found by my static analysis tool and my code review. Signed-off-by:
Jia-Ju Bai <baijiaju1990@163.com> Signed-off-by:
-
Kurt Garloff authored
[ Upstream commit 909cf3e1 ] All EMC SYMMETRIX support REPORT_LUNS, even if configured to report SCSI-2 for whatever reason. Signed-off-by:
Kurt Garloff <garloff@suse.de> Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
NeilBrown authored
[ Upstream commit 235b6003 ] When reshaping a fully degraded raid5/raid6 to a larger nubmer of devices, the new device(s) are not in-sync and so that can make the newly grown stripe appear to be "failed". To avoid this, we set the R5_Expanded flag to say "Even though this device is not fully in-sync, this block is safe so don't treat the device as failed for this stripe". This flag is set for data devices, not not for parity devices. Consequently, if you have a RAID6 with two devices that are partly recovered and a spare, and start a reshape to include the spare, then when the reshape gets past the point where the recovery was up to, it will think the stripes are failed and will get into an infinite loop, failing to make progress. So when contructing parity on an EXPAND_READY stripe, set R5_Expanded. Reported-by:
Curt <lightspd@gmail.com> Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Linus Walleij authored
[ Upstream commit 1c363531 ] The build robot is complaining on Blackfin: drivers/pinctrl/pinctrl-adi2.c: In function 'port_setup': >> drivers/pinctrl/pinctrl-adi2.c:221:21: error: dereferencing pointer to incomplete type 'struct gpio_port_t' writew(readw(®s->port_fer) & ~BIT(offset), ^~ drivers/pinctrl/pinctrl-adi2.c: In function 'adi_gpio_ack_irq': >> drivers/pinctrl/pinctrl-adi2.c:266:18: error: dereferencing pointer to incomplete type 'struct bfin_pint_regs' if (readl(®s->invert_set) & pintbit) ^~ It seems the driver need to include <asm/gpio.h> and <asm/irq.h> to compile. The Blackfin architecture was re-defining the Kconfig PINCTRL symbol which is not OK, so replaced this with PINCTRL_BLACKFIN_ADI2 which selects PINCTRL and PINCTRL_ADI2 just like most arches do. Further, the old GPIO driver symbol GPIO_ADI was possible to select at the same time as selecting PINCTRL. This was not working because the arch-local <asm/gpio.h> header contains an explicit #ifndef PINCTRL clause making compilation break if you combine them. The same is true for DEBUG_MMRS. Make sure the ADI2 pinctrl driver is not selected at the same time as the old GPIO implementation. (This should be converted to use gpiolib or pincontrol and move to drivers/...) Also make sure the old GPIO_ADI driver or DEBUG_MMRS is not selected at the same time as the new PINCTRL implementation, and only make PINCTRL_ADI2 selectable for the Blackfin families that actually have it. This way it is still possible to add e.g. I2C-based pin control expanders on the Blackfin. Cc: Steven Miao <realmz6@gmail.com> Cc: Huanhuan Feng <huanhuan.feng@analog.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Bin Liu authored
commit bd3486de upstream. When babble condition happens, the musb controller might automatically turns off VBUS. On DA8xx platform, the controller generates drvvbus interrupt for turning off VBUS along with the babble interrupt. In this case, we should handle the babble interrupt first and recover from the babble condition. This change ignores the drvvbus interrupt if babble interrupt is also generated at the same time, so the babble recovery routine works properly. Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
nixiaoming authored
[ Upstream commit c79dde62 ] After rmmod 8250.ko tty_kref_put starts kwork (release_one_tty) to release proc interface oops when accessing driver->driver_name in proc_tty_unregister_driver Use jprobe, found driver->driver_name point to 8250.ko static static struct uart_driver serial8250_reg .driver_name= serial, Use name in proc_dir_entry instead of driver->driver_name to fix oops test on linux 4.1.12: BUG: unable to handle kernel paging request at ffffffffa01979de IP: [<ffffffff81310f40>] strchr+0x0/0x30 PGD 1a0d067 PUD 1a0e063 PMD 851c1f067 PTE 0 Oops: 0000 [#1] PREEMPT SMP Modules linked in: ... ... [last unloaded: 8250] CPU: 7 PID: 116 Comm: kworker/7:1 Tainted: G O 4.1.12 #1 Hardware name: Insyde RiverForest/Type2 - Board Product Name1, BIOS NE5KV904 12/21/2015 Workqueue: events release_one_tty task: ffff88085b684960 ti: ffff880852884000 task.ti: ffff880852884000 RIP: 0010:[<ffffffff81310f40>] [<ffffffff81310f40>] strchr+0x0/0x30 RSP: 0018:ffff880852887c90 EFLAGS: 00010282 RAX: ffffffff81a5eca0 RBX: ffffffffa01979de RCX: 0000000000000004 RDX: ffff880852887d10 RSI: 000000000000002f RDI: ffffffffa01979de RBP: ffff880852887cd8 R08: 0000000000000000 R09: ffff88085f5d94d0 R10: 0000000000000195 R11: 0000000000000000 R12: ffffffffa01979de R13: ffff880852887d00 R14: ffffffffa01979de R15: ffff88085f02e840 FS: 0000000000000000(0000) GS:ffff88085f5c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffa01979de CR3: 0000000001a0c000 CR4: 00000000001406e0 Stack: ffffffff812349b1 ffff880852887cb8 ffff880852887d10 ffff88085f5cd6c2 ffff880852800a80 ffffffffa01979de ffff880852800a84 0000000000000010 ffff88085bb28bd8 ffff880852887d38 ffffffff812354f0 ffff880852887d08 Call Trace: [<ffffffff812349b1>] ? __xlate_proc_name+0x71/0xd0 [<ffffffff812354f0>] remove_proc_entry+0x40/0x180 [<ffffffff815f6811>] ? _raw_spin_lock_irqsave+0x41/0x60 [<ffffffff813be520>] ? destruct_tty_driver+0x60/0xe0 [<ffffffff81237c68>] proc_tty_unregister_driver+0x28/0x40 [<ffffffff813be548>] destruct_tty_driver+0x88/0xe0 [<ffffffff813be5bd>] tty_driver_kref_put+0x1d/0x20 [<ffffffff813becca>] release_one_tty+0x5a/0xd0 [<ffffffff81074159>] process_one_work+0x139/0x420 [<ffffffff810745a1>] worker_thread+0x121/0x450 [<ffffffff81074480>] ? process_scheduled_works+0x40/0x40 [<ffffffff8107a16c>] kthread+0xec/0x110 [<ffffffff81080000>] ? tg_rt_schedulable+0x210/0x220 [<ffffffff8107a080>] ? kthread_freezable_should_stop+0x80/0x80 [<ffffffff815f7292>] ret_from_fork+0x42/0x70 [<ffffffff8107a080>] ? kthread_freezable_should_stop+0x80/0x80 Signed-off-by:
nixiaoming <nixiaoming@huawei.com> Signed-off-by:
-
Michael Ellerman authored
[ Upstream commit 05c14c03 ] In the hv-24x7 code there is a function memord() which tries to implement a sort function return -1, 0, 1. However one of the conditions is incorrect, such that it can never be true, because we will have already returned. I don't believe there is a bug in practice though, because the comparisons are an optimisation prior to calling memcmp(). Fix it by swapping the second comparision, so it can be true. Reported-by:
David Binderman <dcb314@hotmail.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Martin Wilck authored
[ Upstream commit dfb2e6f4 ] This patch cleans up a lot of warnings when unloading the driver. A current example of the stack trace starts with: [ 142.570715] sysfs group 'power' not found for kobject 'port-5:0' There can be hundreds of these messages during a driver unload. I am resubmitting this patch on behalf of Martin Wilck with his permission. His original patch can be found here: https://www.spinics.net/lists/linux-scsi/msg102085.html This patch did not help until Hannes's commit 9441284fbc39 ("scsi-fixup-kernel-warning-during-rmmod") was applied to the kernel. --------------------------- Original patch description: --------------------------- Unloading the hpsa driver causes warnings [ 1063.793652] WARNING: CPU: 1 PID: 4850 at ../fs/sysfs/group.c:237 device_del+0x54/0x240() [ 1063.793659] sysfs group ffffffff81cf21a0 not found for kobject 'port-2:0' with two different stacks: 1) [ 1063.793774] [<ffffffff81448af4>] device_del+0x54/0x240 [ 1063.793780] [<ffffffff8145178a>] transport_remove_classdev+0x4a/0x60 [ 1063.793784] [<ffffffff81451216>] attribute_container_device_trigger+0xa6/0xb0 [ 1063.793802] [<ffffffffa0105d46>] sas_port_delete+0x126/0x160 [scsi_transport_sas] [ 1063.793819] [<ffffffffa036ebcc>] hpsa_free_sas_port+0x3c/0x70 [hpsa] 2) [ 1063.797103] [<ffffffff81448af4>] device_del+0x54/0x240 [ 1063.797118] [<ffffffffa0105d4e>] sas_port_delete+0x12e/0x160 [scsi_transport_sas] [ 1063.797134] [<ffffffffa036ebcc>] hpsa_free_sas_port+0x3c/0x70 [hpsa] This is caused by the fact that host device hostX is deleted before the SAS transport devices hostX/port-a:b. This patch fixes this by reverting the order of device deletions. Tested-by:
Don Brace <don.brace@microsemi.com> Reviewed-by:
Martin Wilck <mwilck@suse.de> Signed-off-by:
-
Martin Wilck authored
[ Upstream commit 55ca38b4 ] I am resubmitting this patch on behalf of Martin Wilck with his permission. The original patch can be found here: https://www.spinics.net/lists/linux-scsi/msg102083.html This patch did not help until Hannes's commit 9441284fbc39 ("scsi-fixup-kernel-warning-during-rmmod") was applied to the kernel. -------------------------------------- Original patch description from Martin: -------------------------------------- When the hpsa module is unloaded using rmmod, dangling symlinks remain under /sys/class/sas_phy. Fix this by calling sas_phy_delete() rather than sas_phy_free (which, according to comments, should not be called for PHYs that have been set up successfully, anyway). Tested-by:
-
Alex Williamson authored
[ Upstream commit 16b6c8bb ] When removing a device, for example a VF being removed due to SR-IOV teardown, a "soft" hot-unplug via 'echo 1 > remove' in sysfs, or an actual hot-unplug, we first remove the procfs and sysfs attributes for the device before attempting to release the device from any driver bound to it. Unbinding the driver from the device can take time. The device might need to write out data or it might be actively in use. If it's in use by userspace through a vfio driver, the unbind might block until the user releases the device. This leads to a potentially non-trivial amount of time where the device exists, but we've torn down the interfaces that userspace uses to examine devices, for instance lspci might generate this sort of error: pcilib: Cannot open /sys/bus/pci/devices/0000:01:0a.3/config lspci: Unable to read the standard configuration space header of device 0000:01:0a.3 We don't seem to have any dependence on this teardown ordering in the kernel, so let's unbind the driver first, which is also more symmetric with the instantiation of the device in pci_bus_add_device(). Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Christoph Hellwig authored
[ Upstream commit 5e422f5e ] There was one spot in xfs_bmap_add_extent_unwritten_real that didn't use the passed in new extent state but always converted to normal, leading to wrong behavior when converting from normal to unwritten. Only found by code inspection, it seems like this code path to move partial extent from written to unwritten while merging it with the next extent is rarely exercised. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Brian Foster <bfoster@redhat.com> Reviewed-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Brian Foster authored
[ Upstream commit 9f2a4505 ] It is possible for mkfs to format very small filesystems with too small of an internal log with respect to the various minimum size and block count requirements. If this occurs when the log happens to be smaller than the scan window used for cycle verification and the scan wraps the end of the log, the start_blk calculation in xlog_find_head() underflows and leads to an attempt to scan an invalid range of log blocks. This results in log recovery failure and a failed mount. Since there may be filesystems out in the wild with this kind of geometry, we cannot simply refuse to mount. Instead, cap the scan window for cycle verification to the size of the physical log. This ensures that the cycle verification proceeds as expected when the scan wraps the end of the log. Reported-by:
Zorro Lang <zlang@redhat.com> Signed-off-by:
-
Jiri Slaby authored
[ Upstream commit 4dc12ffe ] l2tp_tunnel_delete does not return anything since commit 62b982ee ("l2tp: fix race condition in l2tp_tunnel_delete"). But call sites of l2tp_tunnel_delete still do casts to void to avoid unused return value warnings. Kill these now useless casts. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: Sabrina Dubroca <sd@queasysnail.net> Cc: Guillaume Nault <g.nault@alphalink.fr> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Acked-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
tang.junhui authored
[ Upstream commit c1573137 ] Currently, Cache missed IOs are identified by s->cache_miss, but actually, there are many situations that missed IOs are not assigned a value for s->cache_miss in cached_dev_cache_miss(), for example, a bypassed IO (s->iop.bypass = 1), or the cache_bio allocate failed. In these situations, it will go to out_put or out_submit, and s->cache_miss is null, which leads bch_mark_cache_accounting() to treat this IO as a hit IO. [ML: applied by 3-way merge] Signed-off-by:
tang.junhui <tang.junhui@zte.com.cn> Reviewed-by:
Michael Lyle <mlyle@lyle.org> Reviewed-by:
Coly Li <colyli@suse.de> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Liang Chen authored
[ Upstream commit 330a4db8 ] mutex_destroy does nothing most of time, but it's better to call it to make the code future proof and it also has some meaning for like mutex debug. As Coly pointed out in a previous review, bcache_exit() may not be able to handle all the references properly if userspace registers cache and backing devices right before bch_debug_init runs and bch_debug_init failes later. So not exposing userspace interface until everything is ready to avoid that issue. Signed-off-by:
Liang Chen <liangchen.linux@gmail.com> Reviewed-by:
Eric Wheeler <bcache@linux.ewheeler.net> Signed-off-by:
-
Bob Peterson authored
[ Upstream commit cc555b09 ] This patch fixes a deadlock caused when the jdata flag is set for inodes that are already on the ordered write list. Since it is on the ordered write list, log_flush calls gfs2_ordered_write which calls filemap_fdatawrite. But since the inode had the jdata flag set, that calls gfs2_jdata_writepages, which tries to start a new transaction. A new transaction cannot be started because it tries to acquire the log_flush rwsem which is already locked by the log flush operation. The bottom line is: We cannot switch an inode from ordered to jdata until we eliminate any ordered data pages (via log flush) or any log_flush operation afterward will create the circular dependency above. So we need to flush the log before setting the diskflags to switch the file mode, then we need to remove the inode from the ordered writes list. Before this patch, the log flush was done for jdata->ordered, but that's wrong. If we're going from jdata to ordered, we don't need to call gfs2_log_flush because the call to filemap_fdatawrite will do it for us: filemap_fdatawrite() -> __filemap_fdatawrite_range() __filemap_fdatawrite_range() -> do_writepages() do_writepages() -> gfs2_jdata_writepages() gfs2_jdata_writepages() -> gfs2_log_flush() This patch modifies function do_gfs2_set_flags so that if a file has its jdata flag set, and it's already on the ordered write list, the log will be flushed and it will be removed from the list before setting the flag. Signed-off-by:
Bob Peterson <rpeterso@redhat.com> Signed-off-by:
Andreas Gruenbacher <agruenba@redhat.com> Acked-by:
Abhijith Das <adas@redhat.com> Signed-off-by:
-
Daniel Lezcano authored
[ Upstream commit 07209fcf ] There is a particular situation when the cooling device is cpufreq and the heat dissipation is not efficient enough where the temperature increases little by little until reaching the critical threshold and leading to a SoC reset. The behavior is reproducible on a hikey6220 with bad heat dissipation (eg. stacked with other boards). Running a simple C program doing while(1); for each CPU of the SoC makes the temperature to reach the passive regulation trip point and ends up to the maximum allowed temperature followed by a reset. This issue has been also reported by running the libhugetlbfs test suite. What is observed is a ping pong between two cpu frequencies, 1.2GHz and 900MHz while the temperature continues to grow. It appears the step wise governor calls get_target_state() the first time with the throttle set to true and the trend to 'raising'. The code selects logically the next state, so the cpu frequency decreases from 1.2GHz to 900MHz, so far so good. The temperature decreases immediately but still stays greater than the trip point, then get_target_state() is called again, this time with the throttle set to true *and* the trend to 'dropping'. From there the algorithm assumes we have to step down the state and the cpu frequency jumps back to 1.2GHz. But the temperature is still higher than the trip point, so get_target_state() is called with throttle=1 and trend='raising' again, we jump to 900MHz, then get_target_state() is called with throttle=1 and trend='dropping', we jump to 1.2GHz, etc ... but the temperature does not stabilizes and continues to increase. [ 237.922654] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 237.922678] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 237.922690] thermal cooling_device0: cur_state=0 [ 237.922701] thermal cooling_device0: old_target=0, target=1 [ 238.026656] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 238.026680] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1 [ 238.026694] thermal cooling_device0: cur_state=1 [ 238.026707] thermal cooling_device0: old_target=1, target=0 [ 238.134647] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 238.134667] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 238.134679] thermal cooling_device0: cur_state=0 [ 238.134690] thermal cooling_device0: old_target=0, target=1 In this situation the temperature continues to increase while the trend is oscillating between 'dropping' and 'raising'. We need to keep the current state untouched if the throttle is set, so the temperature can decrease or a higher state could be selected, thus preventing this oscillation. Keeping the next_target untouched when 'throttle' is true at 'dropping' time fixes the issue. The following traces show the governor does not change the next state if trend==2 (dropping) and throttle==1. [ 2306.127987] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 2306.128009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 2306.128021] thermal cooling_device0: cur_state=0 [ 2306.128031] thermal cooling_device0: old_target=0, target=1 [ 2306.231991] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 2306.232016] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1 [ 2306.232030] thermal cooling_device0: cur_state=1 [ 2306.232042] thermal cooling_device0: old_target=1, target=1 [ 2306.335982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1 [ 2306.336006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=1 [ 2306.336021] thermal cooling_device0: cur_state=1 [ 2306.336034] thermal cooling_device0: old_target=1, target=1 [ 2306.439984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 2306.440008] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0 [ 2306.440022] thermal cooling_device0: cur_state=1 [ 2306.440034] thermal cooling_device0: old_target=1, target=0 [ ... ] After a while, if the temperature continues to increase, the next state becomes 2 which is 720MHz on the hikey. That results in the temperature stabilizing around the trip point. [ 2455.831982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 2455.832006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=0 [ 2455.832019] thermal cooling_device0: cur_state=1 [ 2455.832032] thermal cooling_device0: old_target=1, target=1 [ 2455.935985] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1 [ 2455.936013] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0 [ 2455.936027] thermal cooling_device0: cur_state=1 [ 2455.936040] thermal cooling_device0: old_target=1, target=1 [ 2456.043984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1 [ 2456.044009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0 [ 2456.044023] thermal cooling_device0: cur_state=1 [ 2456.044036] thermal cooling_device0: old_target=1, target=1 [ 2456.148001] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 2456.148028] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 2456.148042] thermal cooling_device0: cur_state=1 [ 2456.148055] thermal cooling_device0: old_target=1, target=2 [ 2456.252009] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 2456.252041] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0 [ 2456.252058] thermal cooling_device0: cur_state=2 [ 2456.252075] thermal cooling_device0: old_target=2, target=1 IOW, this change is needed to keep the state for a cooling device if the temperature trend is oscillating while the temperature increases slightly. Without this change, the situation above leads to a catastrophic crash by a hardware reset on hikey. This issue has been reported to happen on an OMAP dra7xx also. Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Keerthy <j-keerthy@ti.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Leo Yan <leo.yan@linaro.org> Tested-by:
Keerthy <j-keerthy@ti.com> Reviewed-by:
Eduardo Valentin <edubezval@gmail.com> Signed-off-by:
-
Gao Feng authored
[ Upstream commit f02b2320 ] The mutex_destroy only makes sense when enable DEBUG_MUTEX. For the good readbility, it's better to invoke it in exit func when the init func invokes mutex_init. Signed-off-by:
Gao Feng <gfree.wind@vip.163.com> Acked-by:
-
Michał Mirosław authored
[ Upstream commit 54eff226 ] According to comments in code and common sense, cclk_lp uses its own divisor, not cclk_g's. Fixes: b08e8c0e ("clk: tegra: add clock support for Tegra30") Signed-off-by:
Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-By:
Peter De Schrijver <pdeschrijver@nvidia.com> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Sébastien Szymanski authored
[ Upstream commit c68ee58d ] On i.MX6 SoCs without VPU (in my case MCIMX6D4AVT10AC), the hdmi driver fails to probe: [ 2.540030] dwhdmi-imx 120000.hdmi: Unsupported HDMI controller (0000:00:00) [ 2.548199] imx-drm display-subsystem: failed to bind 120000.hdmi (ops dw_hdmi_imx_ops): -19 [ 2.557403] imx-drm display-subsystem: master bind failed: -19 That's because hdmi_isfr's parent, video_27m, is not correctly ungated. As explained in commit 5ccc248c ("ARM: imx6q: clk: Add support for mipi_core_cfg clock as a shared clock gate"), video_27m is gated by CCM_CCGR3[CG8]. On i.MX6 SoCs with VPU, the hdmi is working thanks to the CCM_CMEOR[mod_en_ov_vpu] bit which makes the video_27m ungated whatever is in CCM_CCGR3[CG8]. The issue can be reproduced by setting CCMEOR[mod_en_ov_vpu] to 0. Make the HDMI work in every case by setting hdmi_isfr's parent to mipi_core_cfg. Signed-off-by:
Sébastien Szymanski <sebastien.szymanski@armadeus.com> Reviewed-by:
Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Chen Zhong authored
[ Upstream commit c955bf39 ] Since the previous setup always sets the PLL using crystal 26MHz, this doesn't always happen in every MediaTek platform. So the patch added flexibility for assigning extra member for determining the PLL source clock. Signed-off-by:
Chen Zhong <chen.zhong@mediatek.com> Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
-
Jan Kara authored
[ Upstream commit 592e2545 ] _calc_vm_trans() does not handle the situation when some of the passed flags are 0 (which can happen if these VM flags do not make sense for the architecture). Improve the _calc_vm_trans() macro to return 0 in such situation. Since all passed flags are constant, this does not add any runtime overhead. Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Robert Baronescu authored
[ Upstream commit 7aacbfcb ] Fix the way the length of the buffers used for encryption / decryption are computed. For e.g. in case of encryption, input buffer does not contain an authentication tag. Signed-off-by:
Robert Baronescu <robert.baronescu@nxp.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Suzuki K Poulose authored
[ Upstream commit c7f5828b ] When the PMU driver is built as a module, the perf expects the pmu->module to be valid, so that the driver is prevented from being unloaded while it is in use. Fix the CCN pmu driver to fill in this field. Fixes: a33b0daa ("bus: ARM CCN PMU driver") Cc: Pawel Moll <pawel.moll@arm.com> Cc: Will Deacon <will.deacon@arm.com> Acked-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Jiang Yi authored
[ Upstream commit 594e25e7 ] The function fd_execute_unmap() in target_core_file.c calles ret = file->f_op->fallocate(file, mode, pos, len); Some filesystems implement fallocate() to return error if length is zero (e.g. btrfs) but according to SCSI Block Commands spec UNMAP should return success for zero length. Signed-off-by:
Jiang Yi <jiangyilism@gmail.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
tangwenji authored
[ Upstream commit 24528f08 ] When is pr_reg->isid_present_at_reg is false,this function should return. This fixes a regression originally introduced by: commit d2843c17 Author: Andy Grover <agrover@redhat.com> Date: Thu May 16 10:40:55 2013 -0700 target: Alter core_pr_dump_initiator_port for ease of use Signed-off-by:
tangwenji <tang.wenji@zte.com.cn> Signed-off-by:
-
tangwenji authored
[ Upstream commit 12d5a43b ] tpg must free when call core_tpg_register() return fail Signed-off-by:
-
Bart Van Assche authored
[ Upstream commit cfe2b621 ] Avoid that cmd->se_cmd.se_tfo is read after a command has already been freed. Signed-off-by:
Bart Van Assche <bart.vanassche@wdc.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Mike Christie <mchristi@redhat.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Christophe Leroy authored
[ Upstream commit 6b148a7c ] IPIC Status is provided by register IPIC_SERSR and not by IPIC_SERMR which is the mask register. Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
-
William A. Kennington III authored
[ Upstream commit 71e24d77 ] The current code checks the completion map to look for the first token that is complete. In some cases, a completion can come in but the token can still be on lease to the caller processing the completion. If this completed but unreleased token is the first token found in the bitmap by another tasks trying to acquire a token, then the __test_and_set_bit call will fail since the token will still be on lease. The acquisition will then fail with an EBUSY. This patch reorganizes the acquisition code to look at the opal_async_token_map for an unleased token. If the token has no lease it must have no outstanding completions so we should never see an EBUSY, unless we have leased out too many tokens. Since opal_async_get_token_inrerruptible is protected by a semaphore, we will practically never see EBUSY anymore. Fixes: 8d724823 ("powerpc/powernv: Infrastructure to support OPAL async completion") Signed-off-by:
William A. Kennington III <wak@google.com> Signed-off-by:
-
KUWAZAWA Takuya authored
[ Upstream commit c5504f72 ] Information about ipvs in different network namespace can be seen via procfs. How to reproduce: # ip netns add ns01 # ip netns add ns02 # ip netns exec ns01 ip a add dev lo 127.0.0.1/8 # ip netns exec ns02 ip a add dev lo 127.0.0.1/8 # ip netns exec ns01 ipvsadm -A -t 10.1.1.1:80 # ip netns exec ns02 ipvsadm -A -t 10.1.1.2:80 The ipvsadm displays information about its own network namespace only. # ip netns exec ns01 ipvsadm -Ln IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn TCP 10.1.1.1:80 wlc # ip netns exec ns02 ipvsadm -Ln IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn TCP 10.1.1.2:80 wlc But I can see information about other network namespace via procfs. # ip netns exec ns01 cat /proc/net/ip_vs IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn TCP 0A010101:0050 wlc TCP 0A010102:0050 wlc # ip netns exec ns02 cat /proc/net/ip_vs IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn TCP 0A010102:0050 wlc Signed-off-by:
KUWAZAWA Takuya <albatross0@gmail.com> Acked-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Shriya authored
[ Upstream commit cd77b5ce ] The call to /proc/cpuinfo in turn calls cpufreq_quick_get() which returns the last frequency requested by the kernel, but may not reflect the actual frequency the processor is running at. This patch makes a call to cpufreq_get() instead which returns the current frequency reported by the hardware. Fixes: fb5153d0 ("powerpc: powernv: Implement ppc_md.get_proc_freq()") Signed-off-by:
Shriya <shriyak@linux.vnet.ibm.com> Signed-off-by:
-
Qiang authored
[ Upstream commit 3ad3f8ce ] PCIe PME and native hotplug share the same interrupt number, so hotplug interrupts are also processed by PME. In some cases, e.g., a Link Down interrupt, a device may be present but unreachable, so when we try to read its Root Status register, the read fails and we get all ones data (0xffffffff). Previously, we interpreted that data as PCI_EXP_RTSTA_PME being set, i.e., "some device has asserted PME," so we scheduled pcie_pme_work_fn(). This caused an infinite loop because pcie_pme_work_fn() tried to handle PME requests until PCI_EXP_RTSTA_PME is cleared, but with the link down, PCI_EXP_RTSTA_PME can't be cleared. Check for the invalid 0xffffffff data everywhere we read the Root Status register. 1469d17d ("PCI: pciehp: Handle invalid data when reading from non-existent devices") added similar checks in the hotplug driver. Signed-off-by:
Qiang Zheng <zhengqiang10@huawei.com> [bhelgaas: changelog, also check in pcie_pme_work_fn(), use "~0" to follow other similar checks] Signed-off-by:
-
Peter Ujfalusi authored
[ Upstream commit 288e7560 ] The used 0x1f mask is only valid for am335x family of SoC, different family using this type of crossbar might have different number of electable events. In case of am43xx family 0x3f mask should have been used for example. Instead of trying to handle each family's mask, just use u8 type to store the mux value since the event offsets are aligned to byte offset. Fixes: 42dbdcc6 ("dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx") Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Philipp Zabel authored
[ Upstream commit a3350f9c ] The pcf8563_clkout_recalc_rate function erroneously ignores the frequency index read from the CLKO register and always returns 32768 Hz. Fixes: a39a6405 ("rtc: pcf8563: add CLKOUT to common clock framework") Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit 8cae353e ] 'ret' is known to be 0 at this point. In case of memory allocation error in 'framebuffer_alloc()', return -ENOMEM instead. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Tejun Heo <tj@kernel.org> Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit 451f1306 ] We should go through the error handling code instead of returning -ENOMEM directly. Signed-off-by:
-
Ladislav Michl authored
[ Upstream commit c9876947 ] While usb_control_msg function expects timeout in miliseconds, a value of HZ is used. Replace it with USB_CTRL_GET_TIMEOUT and also fix error message which looks like: udlfb: Read EDID byte 78 failed err ffffff92 as error is either negative errno or number of bytes transferred use %d format specifier. Returned EDID is in second byte, so return error when less than two bytes are received. Fixes: 18dffdf8 ("staging: udlfb: enhance EDID and mode handling support") Signed-off-by:
Ladislav Michl <ladis@linux-mips.org> Cc: Bernie Thompson <bernie@plugable.com> Signed-off-by:
-
