- 27 Jul, 2011 40 commits
-
-
Devin Heitmueller authored
It was confirmed by DibCom that i2c stretching is broken in the i2c master on the dib7700. So we need to put a hack into the xc4000 driver to not complain in certain very specific cases where we know i2c stretching occurs. Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Setup a proper AGC config for the 340e, based on the Windows USB trace Signed-off-by:
-
Devin Heitmueller authored
Remove hard-coded references to 5400, using the value passed in when the xc4000 is attached. Signed-off-by:
-
Devin Heitmueller authored
Properly setup the standard firmware loading and scode loading, as well as getting rid of a ton of dead code. Note that I am getting a single i2c error when the standard firmware sets the video standard, but everything else seems to be loading properly now. Signed-off-by:
-
Devin Heitmueller authored
Add code to handle firmware blobs for the standard and scode. Note there appears to be some issue with loading the DTV8 standard firmware, probably related to direct/indirect mode. Signed-off-by:
-
Devin Heitmueller authored
Since we use the xc3028 version of the firmware file parsing routine (which includes support for scodes and separate blobs), we can drop the xc5000 version of the code. Signed-off-by:
-
Devin Heitmueller authored
The xc4000 driver is based on the original xc5000 driver, and while the xc5000 supports the XREG_BUSY register, the xc4000 does not. So remove the code in question. Signed-off-by:
-
Devin Heitmueller authored
We need to set the firmware type properly in order to locate the init1 firmware. Signed-off-by:
-
Devin Heitmueller authored
The xc3028 version does i2c splitting in a different manner than xc4000 and xc5000, so reuse the xc5000 version of the routine (the key here being that xc4000 expects the first *two* bytes to be the same for splitting transactions. Doing it the xc3028 way was resulting in i2c errors partially through the firmware load. With this change, it would appear that the entire base firmware is being loaded successfully (product id now properly shows 0x0FA0). Signed-off-by:
-
Devin Heitmueller authored
Switch over to using the firmware management routines from the tuner-xc2028, since that has support for scodes, etc. This code still requires signficant cleanup, and at this point the base firmware does not load properly (i2c write errors about 300 bytes in). Signed-off-by:
-
Devin Heitmueller authored
We need to set the dev.parent member on the dib7000p on its i2c master, or else calls to request_firmware() will hit an oops in 2.6.31. Signed-off-by:
-
Devin Heitmueller authored
Add a sleep since in some cases the dib7000p wasn't online when being probed. The optimal timing has not yet been determined. Signed-off-by:
-
Devin Heitmueller authored
Use the correct i2c bus to communicate with the tuner, and properly setup the reset GPIO and i2c address. Signed-off-by:
-
Devin Heitmueller authored
Provide a frontend setup routine for the PCTV 340e which takes into account the specific GPIO setup of the board. Note that this patch does *not* take into account the xc4000 reset pin, which is attached to the dib7000. Signed-off-by:
-
Devin Heitmueller authored
Add the board profile for the PCTV 340eSE, since that's what I have here for development. [mchehab@redhat.com: rebased on the top of the current tree] Signed-off-by:
-
Davide Ferri authored
This is initial code written by Davide Ferri for the PCTV 340e, including a new xc4000 driver. I am checking in all the code unmodified, and making no assertions about its quality (other than confirming it compiles). [mchehab@redhat.com: rebased on the top of the current tree] Signed-off-by:
Davide Ferri <davidef1986@gmail.com> Cc: Patrick Boettcher <pboettcher@kernellabs.com> Signed-off-by:
-
Johannes Obermaier authored
The implementation of the gain calculation for this sensor is incorrect. It is only working for the first 127 values. The reason is, that the gain cannot be set directly by writing a value into the gain registers of the sensor. The gain register work this way (see datasheet page 24): bits 0 to 6 are called "initial gain". These are linear. But bits 7 and 8 ("analog multiplicative factors") and bits 9 and 10 ("digital multiplicative factors") work completely different: Each of these bits increase the gain by the factor 2. So if the bits 7-10 are 0011, 0110, 1100 or 0101 for example, the gain from bits 0-6 is multiplied by 4. The order of the bits 7-10 is not important for the resulting gain. (But there are some recommended values for low noise) The current driver doesn't do this correctly: If the current gain is 000 0111 1111 (127) and the gain is increased by 1, you would expect the image to become brighter. But the image is completly dark, because the new gain is 000 1000 0000 (128). This means: Initial gain of 0, multiplied by 2. The result is 0. This patch adds a new function which does the gain calculation and also fixes the same bug for red_balance and blue_balance. Additionally, the driver follows the recommendation from the datasheet, which says, that the gain should always be above 0x0020. Tested-by:Johannes Obermaier <johannes.obermaier@gmail.com> Signed-off-by:
-
Johannes Obermaier authored
There are problems when you use this camera/sensor in a very bright room or outside. The image is completely white, because it is overexposed. The driver uses a default value which is not suitable for all environments. This patch makes it possible to adjust the exposure time by youself. I found out by logging the i2c-data, that the windows driver for this sensor is doing this, too. I tested the camera on a sunny day and after adjusting the exposure time, I was able to see a very good image. Tested-by:
-
Johannes Obermaier authored
According to the datasheet (page 8), the first optical clear pixel-column is not at position 14. The correct/recommended value is 20. Without this patch there is a dark line on the left side of the image. Tested-by:
-
David Härdeman authored
The conversion of winbond-cir to use rc-core seems to have missed a a few bits and pieces which were in my local tree. Kudos to Juan Jesús García de Soria Lucena <skandalfo@gmail.com> for noticing. [mchehab@redhat.com: fix two UTF-8 violations] Signed-off-by:
David Härdeman <david@hardeman.nu> Signed-off-by:
-
Dan Carpenter authored
In the original code, if the allocation failed we dereference "rr3" when it was NULL. Acked-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
-
Dan Carpenter authored
If change_protocol() fails and we goto out_raw, then it calls unlock twice. I noticed that the other time we called change_protocol() we held the &dev->lock, so I changed it to hold it here too. Reviewed-by:
-
Andreas Oberritter authored
- Add missing entry to array "dtv_cmds". - Set array size to DTV_MAX_COMMAND + 1 to avoid future off-by-ones. Reported-by:
Andreas Oberritter <obi@linuxtv.org> Signed-off-by:
-
Uwe Kleine-König authored
Otherwise they clutter the dmesg buffer even on a production kernel. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Manoel Pinheiro authored
The function "rc5_scan" in "dvb_usb.h" is returning invalid value. The value should be returned "u16" but is returning "u8". See example below in "drivers/media/dvb/dvb-usb/opera1.c": send_key = (send_key & 0xffff) | 0x0100; for (i = 0; i < ARRAY_SIZE(rc_map_opera1_table); i++) { if (rc5_scan(&rc_map_opera1_table[i]) == (send_key & 0xffff)) { *state = REMOTE_KEY_PRESSED; *event = rc_map_opera1_table[i].keycode; opst->last_key_pressed = rc_map_opera1_table[i].keycode; break; } opst->last_key_pressed = 0; } Signed-off-by:Manoel Pinheiro <pinusdtv@hotmail.com> Signed-off-by:
-
Ondrej Zary authored
Convert radio-sf16fmr2 to use generic TEA575x implementation. Most of the driver code goes away as SF16-FMR2 is basically just a TEA5757 tuner connected to ISA bus. The card can optionally be equipped with PT2254A volume control (equivalent of TC9154AP) - the volume setting is completely reworked (with balance control added) and tested. Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Acked-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Hans Petter Selasky authored
The info and err macros are already defined by the USB stack. Rename these macros to avoid macro redefinition warnings. Signed-off-by:
Hans Petter Selasky <hselasky@c2i.net> Signed-off-by:
-
Hans Petter Selasky authored
The dbg, warn and info macros are already defined by the USB stack. Rename these macros to avoid macro redefinition warnings. Refactor lineshift in printouts. Signed-off-by:
-
Alexey Khoroshilov authored
radio->int_in_urb is not deallocated on error paths in si470x_usb_driver_probe(). Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Joe Perches authored
Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Hans Petter Selasky authored
Signed-off-by:
-
Ondrej Zary authored
Convert tea575x-tuner to use the new V4L2 control framework. Also add ext_init() callback that can be used by a card driver for additional initialization right before registering the video device (for SF16-FMR2). Also embed struct video_device to struct snd_tea575x to simplify the code. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Hans Petter Selasky authored
Signed-off-by:
-
Sakari Ailus authored
VIDIOC_S_CTRL and VIDIOC_S_EXT_CTRLS return EACCES when setting a read-only control VIDIOC_TRY_EXT_CTRLS when trying a read-only control and VIDIOC_G_CTRL and VIDIOC_G_EXT_CTRLS when getting a write-only control. Document this. Signed-off-by:
Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Newson Edouard authored
On function videobuf_pages_to_sg the statement sg_set_page(&sglist[0], pages[0], PAGE_SIZE - offset, offset) will fail if size is less than PAGE_SIZE. Signed-off-by:
Newson Edouard <newsondev@gmail.com> Signed-off-by:
-
Tejun Heo authored
Signed-off-by: -
Dan Carpenter authored
list_first_entry() always returns non-null here. I think the intent was to test whether there were any entries in the used list. Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Mauro Carvalho Chehab authored
Several cardlist entries are missed. Fix them by running some script magic (about the same scripts we used to have at -hg tree). Signed-off-by:
-
