- 04 Apr, 2023 9 commits
-
-
Krzysztof Kozlowski authored
The PMIC regulators are not supposed to have unit addresses. Fixes: 60b214ef ("arm64: dts: qcom: msm8994-octagon: Configure regulators") Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by:
Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230312183622.460488-7-krzysztof.kozlowski@linaro.org
-
Krzysztof Kozlowski authored
The PMIC regulators are not supposed to have unit addresses. Fixes: e9783584 ("arm64: dts: qcom: msm8994-kitakami: Add VDD_GFX regulator") Signed-off-by:
-
Krzysztof Kozlowski authored
This reverts commit 46546f28 because it mistakenly took PMIC pinctrl/GPIO as TLMM. The TLMM pinctrl uses "gpio" function, but PMIC uses "normal", so original code was correct: msm8998-oneplus-cheeseburger.dtb: pmic@2: gpio@c000:button-backlight-state: 'oneOf' conditional failed, one must be fixed: 'gpio' is not one of ['normal', 'paired', 'func1', 'func2', 'dtest1', 'dtest2', 'dtest3', 'dtest4', 'func3', 'func4'] Fixes: 46546f28 ("arm64: dts: qcom: msm8998-oneplus-cheeseburger: fix backlight pin function") Signed-off-by:
-
Krzysztof Kozlowski authored
The hid-over-i2c takes VDD, not VCC supply. Fix copy-pasta from other boards which use elan,ekth3000 with valid VCC: sc7180-trogdor-pazquel360-lte.dtb: trackpad@15: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Fixes: fb69f6ad ("arm64: dts: qcom: sc7180: Add pazquel dts files") Signed-off-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
-
Krzysztof Kozlowski authored
The hid-over-i2c takes VDD, not VCC supply. Fix copy-pasta from other boards which use elan,ekth3000 with valid VCC: sc7180-trogdor-lazor-limozeen-nots-r4.dtb: trackpad@2c: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Fixes: 2c26adb8 ("arm64: dts: qcom: Add sc7180-lazor-limozeen skus") Signed-off-by:
-
Krzysztof Kozlowski authored
The hid-over-i2c takes VDD, not VCC supply. Fix copy-pasta from other Herobrine boards which use elan,ekth3000 with valid VCC: sc7280-herobrine-villager-r1-lte.dtb: trackpad@2c: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+' Fixes: ee2a6211 ("arm64: dts: qcom: sc7280: Add device tree for herobrine villager") Signed-off-by:
-
Krzysztof Kozlowski authored
gpio-key bindings expect children to be named with generic prefix: sda660-inforce-ifc6560.dtb: gpio-keys: 'volup' does not match any of the regexes: ... Signed-off-by:
-
Yang Xiwen authored
This commit adds support for the uz801 v3.0 WiFi/LTE dongle made by Henan Yiming Technology Co., Ltd. based on MSM8916. Note: The original firmware does not support 64-bit OS. It is necessary to flash 64-bit TZ firmware to boot arm64. Currently supported: - All CPU cores - Buttons - LEDs - Modem - SDHC - USB Device Mode - UART Signed-off-by:
Yang Xiwen <forbidden405@foxmail.com> Reviewed-by:
-
Stephan Gerhold authored
On MSM8916 the wireless connectivity functionality (WiFi/Bluetooth) is split into the digital part inside the SoC and the analog RF part inside a supplementary WCN36xx chip. For MSM8916, three different options exist: - WCN3620 (WLAN 802.11 b/g/n 2.4 GHz + Bluetooth) - WCN3660B (WLAN 802.11 a/b/g/n 2.4/5 GHz + Bluetooth) - WCN3680B (WLAN 802.11ac 2.4/5 GHz + Bluetooth) Choosing one of these is up to the board vendor. This means that the compatible belongs into the board-specific DT part so people porting new boards pay attention to set the correct compatible. Right now msm8916.dtsi sets "qcom,wcn3620" as default compatible, which does not work at all for boards that have WCN3660B or WCN3680B. Remove the default compatible from msm8196.dtsi and move it to the board DT as follows: - Boards with only &pronto { status = "okay"; } used the default "qcom,wcn3620" so far. They now set this explicitly for &wcnss_iris. - Boards with &pronto { ... iris { compatible = "qcom,wcn3660b"; }}; already had an override that just moves to &wcnss_iris now. - For msm8916-samsung-a2015-common.dtsi the WCN compatible differs for boards making use of it (a3u: wcn3620, a5u: wcn3660b, e2015: wcn3620) so the definitions move to the board-specific DT part. Since this requires touching all the board DTs, use this as a chance to name the WCNSS-related labels consistently, so everything is grouped properly when sorted alphabetically. No functional change, just clean-up for more clarity & easier porting. Aside from ordering the generated DTBs are identical. Signed-off-by:Stephan Gerhold <stephan.gerhold@kernkonzept.com> Reviewed-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by:
-
- 28 Mar, 2023 1 commit
-
-
Bjorn Andersson authored
Merge the arm64-fixes-for-6.3 branch to avoid merge conflicts with changes for v6.4.
-
- 27 Mar, 2023 13 commits
-
-
Krzysztof Kozlowski authored
Tianma FHD panel is supposed to be used with fallback compatible: sdm845-xiaomi-beryllium-tianma.dtb: panel@0: compatible: ['tianma,fhd-video'] is too short Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by:
-
Krzysztof Kozlowski authored
Panel does not have children with unit-addresses thus address/size-cells are not valid: sdm845-xiaomi-beryllium-tianma.dtb: panel@0: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected) Signed-off-by: -
Krzysztof Kozlowski authored
Panel does not have children with unit-addresses thus address/size-cells are not valid: panel@0: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
innolux,n116bca-ea1 is not exactly compatible witg innolux,n116bge, as they have their own driver data. Bindings do not allow fallback: sc7180-trogdor-lazor-limozeen-nots-r4.dtb: panel: compatible: ['innolux,n116bca-ea1', 'innolux,n116bge'] is too long Signed-off-by:
-
Krzysztof Kozlowski authored
The panel bindings expect to have only one port, thus they do not allow to use "ports" node: sc7280-herobrine-zombie-nvme-lte.dtb: panel: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The panel bindings expect to have only one port, thus they do not allow to use "ports" node: sc7180-trogdor-wormdingler-rev1-boe.dtb: panel@0: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The panel bindings expect to have only one port, thus they do not allow to use "ports" node: sc7180-trogdor-quackingstick-r0.dtb: panel@0: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The panel bindings expect to have only one port, thus they do not allow to use "ports" node: sc7180-idp.dtb: panel@0: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+' sc7180-idp.dtb: panel@0: 'port' is a required property Signed-off-by:
-
Krzysztof Kozlowski authored
The panel bindings expect to have only one port, thus they do not allow to use "ports" node: sc8280xp-crd.dtb: panel: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The panel bindings expect to have only one port, thus they do not allow to use "ports" node: sc8280xp-lenovo-thinkpad-x13s.dtb: panel: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The panel bindings expect to have only one port, thus they do not allow to use "ports" node: sdm845-cheza-r2.dtb: panel: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Johan Hovold authored
The pmk8280 PMIC PON peripheral is gen3 and uses two sets of registers; hlos and pbs. This specifically fixes the following error message during boot when the pbs registers are not defined: PON_PBS address missing, can't read HW debounce time Note that this also enables the spurious interrupt workaround introduced by commit 0b65118e ("Input: pm8941-pwrkey - add software key press debouncing support") (which may or may not be needed). Fixes: ccd3517f ("arm64: dts: qcom: sc8280xp: Add reference device") Signed-off-by:
Johan Hovold <johan+linaro@kernel.org> Tested-by: Steev Klimaszewski <steev@kali.org> #Thinkpad X13s Reviewed-by:
-
Johan Hovold authored
The sc8280xp pin controller does not have a way to enable or disable the input buffer so drop the unnecessary 'input-enable' property which is about to be deprecated. Link: https://lore.kernel.org/lkml/20230323102605.6.I291ce0ba2c6ea80b341659c4f75a567a76dd7ca6@changeidSigned-off-by:
-
- 24 Mar, 2023 10 commits
-
-
Bjorn Andersson authored
Merge in the topic branch with IPQ5332 GCC DT-binding, to ensure that the header file with GCC clock defines are available.
-
Krzysztof Kozlowski authored
The soc node is supposed to have only device nodes with MMIO addresses, so move the DSI OPP into the DSI controller node to fix: sda660-inforce-ifc6560.dtb: soc: opp-table-dsi: {'compatible': ['operating-points-v2'], ... should not be valid under {'type': 'object'} From schema: dtschema/schemas/simple-bus.yaml Signed-off-by: -
Krzysztof Kozlowski authored
'clocks' node is not a bus, but just a placeholder for clocks: msm8996-xiaomi-gemini.dtb: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$' From schema: dtschema/schemas/simple-bus.yaml msm8996-xiaomi-gemini.dtb: clocks: xo-board: {'compatible': ['fixed-clock'], '#clock-cells': [[0]], ... From schema: dtschema/schemas/simple-bus.yaml Signed-off-by: -
Krzysztof Kozlowski authored
'clocks' node is not a bus, but just a placeholder for clocks: msm8992-msft-lumia-octagon-talkman.dtb: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$' From schema: dtschema/schemas/simple-bus.yaml msm8992-msft-lumia-octagon-talkman.dtb: clocks: xo-board: {'compatible': ['fixed-clock'], '#clock-cells': [[0]], ... From schema: dtschema/schemas/simple-bus.yaml Signed-off-by: -
Krzysztof Kozlowski authored
'clocks' node is not a bus, but just a placeholder for clocks: apq8096-db820c.dtb: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$' From schema: dtschema/schemas/simple-bus.yaml apq8096-db820c.dtb: clocks: xo-board: {'compatible': ['fixed-clock'], '#clock-cells': [[0]], ... From schema: dtschema/schemas/simple-bus.yaml Signed-off-by: -
Neil Armstrong authored
Add the final "s" to the pgio properties and fix the invalid "enable" name to the correct "wake", checked against the HDK8450 schematics. Fixes: bc6588bc ("arm64: dts: qcom: sm8450: add PCIe1 root device") Signed-off-by:
Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by:
-
Neil Armstrong authored
Fixes the following DT bindings check error: pci@1c00000: Unevaluated properties are not allowed ('power-domain-names' were unexpected) Signed-off-by: -
Dmitry Baryshkov authored
Correct PCIe PHY enablement to refer the QMP device nodes rather than PHY device nodes. QMP nodes have 'status = "disabled"' property in the ipq8074.dtsi, while PHY nodes do not correspond to the actual device and do not have the status property. Fixes: 1ed34da6 ("arm64: dts: qcom: Add board support for HK10") Signed-off-by:
-
Dmitry Baryshkov authored
Correct PCIe PHY enablement to refer the QMP device nodes rather than PHY device nodes. QMP nodes have 'status = "disabled"' property in the ipq8074.dtsi, while PHY nodes do not correspond to the actual device and do not have the status property. Fixes: e8a7fdc5 ("arm64: dts: ipq8074: qcom: Re-arrange dts nodes based on address") Signed-off-by:
-
Johan Hovold authored
Enable both touchpad nodes in the devictree and let the HID driver determine which one is actually populated (by attempting to read from each i2c address). Ideally this would not be needed and the boot firmware should instead enable only the node for the populated touchpad, but this is unlikely to ever be realised for the X13s. Note that the pin configuration must currently be moved to the parent i2c-bus node even though only one of these nodes will ever be successfully probed on a specific device (e.g. to allow them to be probed in parallel). Signed-off-by:
-
- 23 Mar, 2023 7 commits
-
-
Krzysztof Kozlowski authored
The WSA881x shutdown GPIO is active low (SD_N), but Linux driver assumed DTS always comes with active high. Since Linux drivers were updated to handle proper flag, correct the DTS. The change is not backwards compatible with older Linux kernel. Signed-off-by:
-
Krzysztof Kozlowski authored
The WSA881x shutdown GPIO is active low (SD_N), but Linux driver assumed DTS always comes with active high. Since Linux drivers were updated to handle proper flag, correct the DTS. The change is not backwards compatible with older Linux kernel. Signed-off-by:
-
Krzysztof Kozlowski authored
The WSA881x shutdown GPIO is active low (SD_N), but Linux driver assumed DTS always comes with active high. Since Linux drivers were updated to handle proper flag, correct the DTS. The change is not backwards compatible with older Linux kernel. Signed-off-by:
-
Krzysztof Kozlowski authored
The WSA881x shutdown GPIO is active low (SD_N), but Linux driver assumed DTS always comes with active high. Since Linux drivers were updated to handle proper flag, correct the DTS. The change is not backwards compatible with older Linux kernel. Signed-off-by:
-
Johan Hovold authored
The SPMI PMIC register region width is fixed and should not be encoded in the devicetree. Fixes: d6dbbda3 ("arm64: dts: qcom: sc8280xp-pmics: add pmk8280 sdam nvram") Signed-off-by:
-
Neil Armstrong authored
Add the Display Port controller subnode to the MDSS node. Signed-off-by:
-
Neil Armstrong authored
The QMP PHY is a USB3/DP combo phy, switch to the newly documented bindings and register the clocks to the GCC and DISPCC controllers. Reviewed-by:
-
