- 07 Apr, 2021 17 commits
-
-
Mark Pearson authored
The BIOS team have added a new API that allows us to retrieve the current performance profile without having to disable/enable CQL mode. Adding the changes to use this API. Tested on P15 and X1C8 Signed-off-by:
Mark Pearson <markpearson@lenovo.com> Link: https://lore.kernel.org/r/20210406233203.232860-1-markpearson@lenovo.comReviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Maximilian Luz authored
Sometimes, the "base connected" event that we rely on to (re-)attach the device connected to the base is sent a bit too early. When this happens, some devices may not be completely ready yet. Specifically, the battery has been observed to report zero-values for things like full charge capacity, which, however, is only loaded once when the driver for that device probes. This can thus result in battery readings being unavailable. As we cannot easily and reliably discern between devices that are not ready yet and devices that are not connected (i.e. will never be ready), delay adding these devices. This should give them enough time to set up. The delay is set to 2.5 seconds, which should give us a good safety margin based on testing and still be fairly responsive for users. To achieve that delay switch to updating via a delayed work struct, which means that we can also get rid of some locking. Signed-off-by:
Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20210405231222.358113-1-luzmaximilian@gmail.comSigned-off-by:
-
Mario Limonciello authored
So that I can always be reached in the future if necessary, add a personal email address. Signed-off-by:
Mario Limonciello <mario.limonciello@dell.com> Link: https://lore.kernel.org/r/20210401162206.26901-4-mario.limonciello@dell.comSigned-off-by:
-
Mario Limonciello authored
This driver is maintained by Dell, but it was missing in MAINTAINERS. Signed-off-by:
-
Mario Limonciello authored
A team of engineers will be helping to service these drivers in the future rather than just one person. Signed-off-by:
-
Srinivas Pandruvada authored
In some cases when firmware is busy or updating, some mailbox commands still timeout on some newer CPUs. To fix this issue, change how we process timeout. With this change, replaced timeout from using simple count with real timeout in micro-seconds using ktime. When the command response takes more than average processing time, yield to other tasks. The worst case timeout is extended upto 1 milli-second. Signed-off-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Link: https://lore.kernel.org/r/20210330220840.3113959-1-srinivas.pandruvada@linux.intel.comSigned-off-by:
-
Srinivas Pandruvada authored
This release adds following changes: - Support increased number of CPUs - Return error when mailbox commmand fails to enable core-power - Option to online all CPUs - Removes build date and time print Signed-off-by:
-
Antonio Terceiro authored
These macros introduce nondeterminism in builds, and break reproducible builds. Signed-off-by:
Antonio Terceiro <antonio.terceiro@linaro.org> Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
-
Srinivas Pandruvada authored
It is possible that users manually offlined CPUs via sysfs interface and then started this utility. In this case we will not be able to get package and die id of the those CPUs. So add an option to force online if required for some commands. Signed-off-by:
-
Srinivas Pandruvada authored
Some older kernels don't support reading core-power status. In that case mailbox command fails. So, display core-power status as "unknown" instead of supported. Signed-off-by:
-
Srinivas Pandruvada authored
The current string size to print cpulist can accommodate upto 80 logical CPUs per package. But this limit is not enough. So increase the string size. Also prevent buffer overflow, if the string size reaches limit. Signed-off-by:
-
Hans de Goede authored
Make init_bios_attributes() ACPI object parsing more robust: 1. Always check that the type of the return ACPI object is package, rather then only checking this for instance_id == 0 2. Check that the package has the minimum amount of elements which will be consumed by the populate_foo_data() for the attr_type Note/TODO: The populate_foo_data() functions should also be made more robust. The should check the type of each of the elements matches the type which they expect and in case of populate_enum_data() obj->package.count should be passed to it as an argument and it should re-check this itself since it consume a variable number of elements. Fixes: e8a60aa7 ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by:
-
Colin Ian King authored
The variable result is being assigned a value that is never read and it is being updated later with a new value. The assignment is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by:Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210326192022.623001-1-colin.king@canonical.comSigned-off-by:
-
Dan Carpenter authored
The "&client->ddev->lock" and "&ddev->lock" are the same thing. Let's use "&ddev->lock" consistently. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
-
Hans de Goede authored
Now that we have 2 separate input_dev-s for the buttons and the switches, this is no longer used, remove it. Signed-off-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20210325123255.73103-1-hdegoede@redhat.com
-
Luca Stefani authored
* On recent ZenBooks the fn-lock is disabled by default on boot while running Windows. * Add a module param ( fnlock_default ) that allows changing the default at probe time Signed-off-by:
Luca Stefani <luca.stefani.ge1@gmail.com> Link: https://lore.kernel.org/r/20210323210126.145286-1-luca.stefani.ge1@gmail.comReviewed-by:
-
Andrea.Ho authored
Advantech sw_button is a ACPI event trigger button. With this driver, we can report KEY_PROG1 on the Advantech Tabletop Network Appliances products and it has been tested in FWA1112VC. Add the software define button support to report EV_REP key_event (KEY_PROG1) by pressing button that could be get on user interface and trigger the customized actions. Signed-off-by:
Andrea.Ho <Andrea.Ho@advantech.com.tw> Link: https://lore.kernel.org/r/20210319034427.23222-1-andrea.cs97g@nctu.edu.twReviewed-by:
-
- 06 Apr, 2021 1 commit
-
-
Hans de Goede authored
Some devices send (duplicate) tablet-mode events when moved around even though the mode has not changed; and they do this even when suspended. Change the tablet-mode event handling when priv->wakeup_mode is set to update the switch state in case it changed and then return immediately (without calling pm_wakeup_hard_event()) to avoid spurious wakeups. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212537 Fixes: 537b0dd4 ("platform/x86: intel-hid: Add support for SW_TABLET_MODE") Signed-off-by:
Elia Devito <eliadevito@gmail.com> Link: https://lore.kernel.org/r/20210404143831.25173-1-hdegoede@redhat.com
-
- 23 Mar, 2021 9 commits
-
-
David E. Box authored
Due to a HW limitation, the Latency Tolerance Reporting (LTR) value programmed in the Tiger Lake GBE controller is not large enough to allow the platform to enter Package C10, which in turn prevents the platform from achieving its low power target during suspend-to-idle. Ignore the GBE LTR value on Tiger Lake. LTR ignore functionality is currently performed solely by a debugfs write call. Split out the LTR code into its own function that can be called by both the debugfs writer and by this work around. Signed-off-by:
David E. Box <david.e.box@linux.intel.com> Reviewed-by:
Sasha Neftin <sasha.neftin@intel.com> Cc: intel-wired-lan@lists.osuosl.org Reviewed-by:
Rajneesh Bhardwaj <irenic.rajneesh@gmail.com> Link: https://lore.kernel.org/r/20210319201844.3305399-2-david.e.box@linux.intel.comSigned-off-by:
-
David E. Box authored
The intel_pmc_core driver is mostly used as a debugging driver for Intel platforms that support SLPS0 (S0ix). But the driver may also be used to communicate actions to the PMC in order to ensure transition to SLPS0 on some systems and architectures. As such the driver should be built on all platforms it supports. Indicate this in the Kconfig. Also update the list of supported features. Signed-off-by:
-
Esteve Varela Colominas authored
Signed-off-by:
Esteve Varela Colominas <esteve.varela@gmail.com> Link: https://lore.kernel.org/r/20210321183512.14551-1-esteve.varela@gmail.comSigned-off-by:
-
kernel test robot authored
drivers/platform/surface/surface_dtx.c:651:2-3: Unneeded semicolon Remove unneeded semicolon. Generated by: scripts/coccinelle/misc/semicolon.cocci Fixes: 1d609992 ("platform/surface: Add DTX driver") CC: Maximilian Luz <luzmaximilian@gmail.com> Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
-
kernel test robot authored
Use kobj_to_dev() instead of container_of() Generated by: scripts/coccinelle/api/kobj_to_dev.cocci CC: Denis Efremov <efremov@linux.com> Reported-by:
Julia Lawall <julia.lawall@inria.fr> Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2103171258010.2981@hadrienSigned-off-by:
-
Bhaskar Chowdhury authored
s/progamming/programming/ Signed-off-by:
Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by:
Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20210317095650.2036419-1-unixbhaskar@gmail.comSigned-off-by:
-
Bhaskar Chowdhury authored
s/derefence/dereference/ Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@cascardo.eti.br> Acked-by:
-
David E. Box authored
Fixes off-by-one bugs in the macro assignments for the crashlog control bits. Was initially tested on emulation but bug revealed after testing on silicon. Fixes: 5ef9998c ("platform/x86: Intel PMT Crashlog capability driver") Signed-off-by:
-
David E. Box authored
Initialize the struct resource in intel_pmt_dev_register to zero to avoid a fault should the char *name field be non-zero. Signed-off-by:
-
- 21 Mar, 2021 11 commits
-
-
Nitin Joshi authored
On some newer Thinkpads we need to set SAR value based on antenna type. This patch provides a sysfs interface that userspace can use to get antenna type and set corresponding SAR value, as is required for FCC certification. Reviewed-by:
Nitin Joshi <njoshi1@lenovo.com> Link: https://lore.kernel.org/r/20210317024636.356175-1-njoshi1@lenovo.comSigned-off-by:
-
Hans de Goede authored
Stop reporting SW_DOCK events because this breaks suspend-on-lid-close. SW_DOCK should only be reported for docking stations, but all the DSDTs in my DSDT collection which use the intel-vbtn code, always seem to use this for 2-in-1s / convertibles and set SW_DOCK=1 when in laptop-mode (in tandem with setting SW_TABLET_MODE=0). This causes userspace to think the laptop is docked to a port-replicator and to disable suspend-on-lid-close, which is undesirable. Map the dock events to KEY_IGNORE to avoid this broken SW_DOCK reporting. Note this may theoretically cause us to stop reporting SW_DOCK on some device where the 0xCA and 0xCB intel-vbtn events are actually used for reporting docking to a classic docking-station / port-replicator but I'm not aware of any such devices. Also the most important thing is that we only report SW_DOCK when it reliably reports being docked to a classic docking-station without any false positives, which clearly is not the case here. If there is a chance of reporting false positives then it is better to not report SW_DOCK at all. Cc: stable@vger.kernel.org Signed-off-by:
-
Hans de Goede authored
Cleanup create_attributes_level_sysfs_files(): 1. There is no need to call sysfs_remove_file() on error, sysman_init() will already call release_attributes_data() on failure which already does this. 2. There is no need for the pr_debug() calls sysfs_create_file() should never fail and if it does it will already complain about the problem itself. Fixes: e8a60aa7 ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by:
-
Hans de Goede authored
When either the attributes or the password interface is not found, then unregister the 2 wmi drivers again and return -ENODEV from sysman_init(). Fixes: e8a60aa7 ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Reported-by:
Alexander Naumann <alexandernaumann@gmx.de> Signed-off-by:
-
Hans de Goede authored
Cleanup sysman_init() error-exit handling: 1. There is no need for the fail_reset_bios and fail_authentication_kset eror-exit cases, these can be handled by release_attributes_data() 2. Rename all the labels from fail_what_failed, to err_what_to_cleanup this is the usual way to name these and avoids the need to rename them when extra steps are added. Fixes: e8a60aa7 ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by:
-
Hans de Goede authored
platform/x86: dell-wmi-sysman: Fix release_attributes_data() getting called twice on init_bios_attributes() failure All calls of init_bios_attributes() will result in a goto fail_create_group if they fail, which calls release_attributes_data(). So there is no need to call release_attributes_data() from init_bios_attributes() on failure itself. Fixes: e8a60aa7 ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by:
-
Hans de Goede authored
During some of the error-exit paths it is possible that release_attributes_data() will get called multiple times, which results in exit_foo_attributes() getting called multiple times. Make it safe to call exit_foo_attributes() multiple times, avoiding double-free()s in this case. Note that release_attributes_data() really should only be called once during error-exit paths. This will be fixed in a separate patch and it is good to have the exit_foo_attributes() functions modified this way regardless. Fixes: e8a60aa7 ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by:
-
Hans de Goede authored
It is possible for release_attributes_data() to get called when the main_dir_kset has not been created yet, move the removal of the bios-reset sysfs attr to under a if (main_dir_kset) check to avoid a NULL pointer deref. Fixes: e8a60aa7 ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Reported-by:
-
Hans de Goede authored
On some system the WMI GUIDs used by dell-wmi-sysman are present but there are no enum type attributes, this causes init_bios_attributes() to return -ENODEV, after which sysman_init() does a "goto fail_create_group" and then calls release_attributes_data(). release_attributes_data() calls kset_unregister(wmi_priv.main_dir_kset); but before this commit it was missing a "wmi_priv.main_dir_kset = NULL;" statement; and after calling release_attributes_data() the sysman_init() error handling does this: if (wmi_priv.main_dir_kset) { kset_unregister(wmi_priv.main_dir_kset); wmi_priv.main_dir_kset = NULL; } Which causes a second kset_unregister(wmi_priv.main_dir_kset), leading to a double-free, which causes a crash. Add the missing "wmi_priv.main_dir_kset = NULL;" statement to release_attributes_data() to fix this double-free crash. Fixes: e8a60aa7 ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: -
Hans de Goede authored
Testing has shown that setting /sys/firmware/acpi/platform_profile to "balanced" when /sys/bus/platform/devices/thinkpad_acpi/dytc_lapmode reports 1, causes dytc_lapmode to get reset to 0 and then it becomes stuck at 0 for aprox. 30 minutes even if the laptop is used on a lap. Disabling CQL (when enabled) before issuing the DYTC_CMD_RESET to get back to balanced mode and re-enabling it afterwards again, like the code already does when switching to low-power / performance mode fixes this. Fixes: c3bfcd4c ("platform/x86: thinkpad_acpi: Add platform profile support") Tested-by:
-
Esteve Varela Colominas authored
On many recent ThinkPad laptops, there's a new LED next to the ESC key, that indicates the FnLock status. When the Fn+ESC combo is pressed, FnLock is toggled, which causes the Media Key functionality to change, making it so that the media keys either perform their media key function, or function as an F-key by default. The Fn key can be used the access the alternate function at any time. With the current linux kernel, the LED doens't change state if you press the Fn+ESC key combo. However, the media key functionality *does* change. This is annoying, since the LED will stay on if it was on during bootup, and it makes it hard to keep track what the current state of the FnLock is. This patch calls an ACPI function, that gets the current media key state, when the Fn+ESC key combo is pressed. Through testing it was discovered that this function causes the LED to update correctly to reflect the current state when this function is called. The relevant ACPI calls are the following: \_SB_.PCI0.LPC0.EC0_.HKEY.GMKS: Get media key state, returns 0x603 if the FnLock mode is enabled, and 0x602 if it's disabled. \_SB_.PCI0.LPC0.EC0_.HKEY.SMKS: Set media key state, sending a 1 will enable FnLock mode, and a 0 will disable it. Relevant discussion: https://bugzilla.kernel.org/show_bug.cgi?id=207841 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1881015Signed-off-by:
-
- 18 Mar, 2021 2 commits
-
-
Mark Pearson authored
Lenovo platforms with DYTC versions earlier than version 5 don't set the lapmode interface correctly, causing issues with thermald on older platforms. Add checking to only create the dytc_lapmode interface for version 5 and later. Fixes: 1ac09656 ("platform/x86: thinkpad_acpi: Add palm sensor support") Signed-off-by:
-
Hans de Goede authored
Immutable branch between MFD and Platform/x86 due for the v5.13 merge window
-
