As per 'commit 3506b2f4 ("net: dsa: microchip: call
phy_remove_link_mode during probe")' phy_remove_link_mode is added in
the switch_register function after dsa_switch_register. In order to have
the common switch register function, moving this phylink validation to
phylink_get_caps validation hook.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At present, ksz8795.c and ksz9477.c have separate dsa_switch_ops
structure initialization. This patch modifies the files such a way that
ksz switches has common dsa_switch_ops in the ksz_common.c file.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch move the setting the start bit from the individual switch
configuration to ksz_setup
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the enabling the multicast storm protection from
individual setup function to ksz_setup function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch move the 10% broadcast protection from the individual setup
to ksz_setup. In the ksz9477, broadcast protection is updated in reset
function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch move the common initialization of switches to ksz_setup and
perform the switch specific initialization using the ksz_dev_ops
function pointer.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to transmit the STP BPDU packet to the CPU port, the STP
address 01-80-c2-00-00-00 has to be added to static alu table for
ksz8795 series switch. For the ksz9477 switch, there is reserved
multicast table which handles forwarding the particular set of
multicast address to cpu port. So enabling the multicast reserved table
and updated the cpu port index. The stp addr is enabled during the setup
phase using the enable_stp_addr pointer in struct ksz_dev_ops.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To have the common set of initialization in ksz_setup, introduced the
new config_cpu_port member to ksz_dev_ops. Since both the ksz8795.c and
ksz9477.c configuring the cpu port in the setup function, introduced the
member.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch renames the shutdown to reset in ksz_dev_ops in order to use
the reset dev_ops in the ksz_setup.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hangbin Liu says:

====================
Bonding: add per-port priority support

This patch set add per-port priority for bonding failover re-selection.

The first patch add a new filed for bond_opt_value so we can set slave
value easier. I will update the bond_option_queue_id_set() setting
in later patch.

The second patch add the per-port priority for bonding. I defined
it as s32 to compatible with team prio option, which also use a s32
value.

v3: store slave_dev in bond_opt_value directly to simplify setting
    values for slave.

v2: using the extant bonding options management stuff instead setting
    slave prio in bond_slave_changelink() directly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add per port priority support for bonding active slave re-selection during
failover. A higher number means higher priority in selection. The primary
slave still has the highest priority. This option also follows the
primary_reselect rules.

This option could only be configured via netlink.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, bond_opt_value are mostly used for bonding option settings. If
we want to set a value for slave, we need to re-alloc a string to store
both slave name and vlaue, like bond_option_queue_id_set() does, which
is complex and dumb.

As Jon suggested, let's add a union field slave_dev for bond_opt_value,
which will be benefit for future slave option setting. In function
__bond_opt_init(), we will always check the extra field and set it
if it's not NULL.
Suggested-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the repeated word 'and' from comments
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Link: https://lore.kernel.org/r/20220622144841.21274-1-jiangjian@cdjrlc.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Remove the repeated word 'and' from comments
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Link: https://lore.kernel.org/r/20220622144526.20659-1-jiangjian@cdjrlc.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The GPY115 and GPY2xx PHYs contain an integrated temperature sensor. It
accuracy is +/- 5°C. Add support for it.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220622141716.3517645-1-michael@walle.ccSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Michael Walle says:

====================
net: use new hwmon_sanitize_name()

These are the remaining patches of my former series [1] which were hold
back because it would have required a stable branch between the subsystems.

[1] https://lore.kernel.org/r/20220405092452.4033674-1-michael@walle.cc/
====================

Link: https://lore.kernel.org/r/20220622123543.3463209-1-michael@walle.ccSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Instead of open-coding the bad characters replacement in the hwmon name,
use the new devm_hwmon_sanitize_name().
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Instead of open-coding the bad characters replacement in the hwmon name,
use the new hwmon_sanitize_name().
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Jonathan Lemon says:

====================
Broadcom PTP PHY support

This adds PTP support for the Broadcom PHY BCM54210E (and the
specific variant BCM54213PE that the rpi-5.15 branch uses).

This has only been tested on the RPI CM4, which has one port.

There are other Broadcom chips which may benefit from using the
same framework here, although with different register sets.
====================

Link: https://lore.kernel.org/r/20220622050454.878052-1-jonathan.lemon@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The perout function is used to generate a 1PPS signal, synchronized
to the PHC.  This is accomplished by a using the hardware oneshot
functionality, which is reset by a timer.

The external timestamp function is set up for a 1PPS input pulse,
and uses a timer to poll for temestamps.

Both functions use the SYNC_OUT/SYNC_IN1 pin, so cannot run
simultaneously.
Co-developed-by: Lasse Johnsen <l@ssejohnsen.me>
Signed-off-by: Lasse Johnsen <l@ssejohnsen.me>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This adds PTP support for BCM54210E Broadcom PHYs, in particular,
the BCM54213PE, as used in the Rasperry PI CM4.  It has only been
tested on that hardware.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add 'struct bcm_ptp_private' to bcm54xx_phy_priv which points to
an optional PTP structure attached to the PHY.  This is allocated
on probe if PHY PTP support is configured, and if the driver supports
PTP for the specified PHY.

Add the bcm_ptp_probe(), bcm_ptp_config_init() and bcn_ptp_stop()
API functions to the bcm-phy library.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Russell King says:

====================
net: dsa: mv88e6xxx: get rid of SPEED_MAX

This series does two things:

1. it gets rid of mv88e6065_port_set_speed_duplex() which is completely
   unused (do we support this device? I couldn't find it in the tables
   in chip.c) This has a max speed of 200Mbps which we don't support.

2. get rid of the SPEED_MAX constant, which is used to configure a DSA
   or CPU port to their maximum speed during initialisation. We no
   longer need this as we can derive the maximum port speed from the
   mac_capabilities instead.

The reason for making this change is in preparation for phylink to be
used by DSA for CPU ports. This omission has come back to bite us with
the conversion of DSA drivers to phylink_pcs, since phylink_pcs won't
get used unless phylink is being used. Particularly with this driver,
it is very common for DT descriptions to omit the fixed-link details
which means "use maximum speed".

It will eventually be necessary to hoist the selection of "max speed"
into the DSA layer (trivial) and also have a way for the DSA driver
to tell the DSA layer which interface it should be using for these
ports.
====================

Link: https://lore.kernel.org/r/YrGQBssOvQBZiDS4@shell.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, all the device specific speed setting functions convert
SPEED_MAX to the actual speed of the port. Rather than having each
of the mv88e6xxx chip specifics handling SPEED_MAX, derive it from
the mac_capabilities instead.

This is only needed for CPU and DSA ports, so move the logic up into
mv88e6xxx_setup_port() - which allows us to kill off all users of
SPEED_MAX throughout the driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove mv88e6065_port_set_speed_duplex() - this is never called, and
thus is completely redundant.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Paolo Abeni:
 "Including fixes from bpf and netfilter.

  Current release - regressions:

   - netfilter: cttimeout: fix slab-out-of-bounds read in
     cttimeout_net_exit

Current release - new code bugs:

   - bpf: ftrace: keep address offset in ftrace_lookup_symbols

   - bpf: force cookies array to follow symbols sorting

  Previous releases - regressions:

   - ipv4: ping: fix bind address validity check

   - tipc: fix use-after-free read in tipc_named_reinit

   - eth: veth: add updating of trans_start

  Previous releases - always broken:

   - sock: redo the psock vs ULP protection check

   - netfilter: nf_dup_netdev: fix skb_under_panic

   - bpf: fix request_sock leak in sk lookup helpers

   - eth: igb: fix a use-after-free issue in igb_clean_tx_ring

   - eth: ice: prohibit improper channel config for DCB

   - eth: at803x: fix null pointer dereference on AR9331 phy

   - eth: virtio_net: fix xdp_rxq_info bug after suspend/resume

  Misc:

   - eth: hinic: replace memcpy() with direct assignment"

* tag 'net-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
  net: openvswitch: fix parsing of nw_proto for IPv6 fragments
  sock: redo the psock vs ULP protection check
  Revert "net/tls: fix tls_sk_proto_close executed repeatedly"
  virtio_net: fix xdp_rxq_info bug after suspend/resume
  igb: Make DMA faster when CPU is active on the PCIe link
  net: dsa: qca8k: reduce mgmt ethernet timeout
  net: dsa: qca8k: reset cpu port on MTU change
  MAINTAINERS: Add a maintainer for OCP Time Card
  hinic: Replace memcpy() with direct assignment
  Revert "drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c"
  net: phy: smsc: Disable Energy Detect Power-Down in interrupt mode
  ice: ethtool: Prohibit improper channel config for DCB
  ice: ethtool: advertise 1000M speeds properly
  ice: Fix switchdev rules book keeping
  ice: ignore protocol field in GTP offload
  netfilter: nf_dup_netdev: add and use recursion counter
  netfilter: nf_dup_netdev: do not push mac header a second time
  selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh
  net/tls: fix tls_sk_proto_close executed repeatedly
  erspan: do not assume transport header is always set
  ...

Pull MMC fixes from Ulf Hansson:

 - mtk-sd: Fix dma hang issues

 - sdhci-pci-o2micro: Fix card detect by dealing with debouncing

* tag 'mmc-v5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: mediatek: wait dma stop bit reset to 0
  mmc: sdhci-pci-o2micro: Fix card detect by dealing with debouncing

Pull sound fixes from Takashi Iwai:
 "All small changes, mostly device-specific:

   - A regression fix for PCM WC-page allocation on x86

   - A regression fix for i915 audio component binding

   - Fixes for (longstanding) beep handling bug

   - Runtime PM fixes for Intel LPE HDMI audio

   - A couple of pending FireWire fixes

   - Usual HD-audio and USB-audio quirks, new Intel dspconf entries"

* tag 'sound-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek: Add quirk for Clevo NS50PU
  ALSA: hda: Fix discovery of i915 graphics PCI device
  ALSA: hda/via: Fix missing beep setup
  ALSA: hda/conexant: Fix missing beep setup
  ALSA: memalloc: Drop x86-specific hack for WC allocations
  ALSA: hda/realtek: Add quirk for Clevo PD70PNT
  ALSA: x86: intel_hdmi_audio: use pm_runtime_resume_and_get()
  ALSA: x86: intel_hdmi_audio: enable pm_runtime and set autosuspend delay
  ALSA: hda: intel-nhlt: remove use of __func__ in dev_dbg
  ALSA: hda: intel-dspcfg: use SOF for UpExtreme and UpExtreme11 boards
  firewire: convert sysfs sprintf/snprintf family to sysfs_emit
  firewire: cdev: fix potential leak of kernel stack due to uninitialized value
  ALSA: hda/realtek: Apply fixup for Lenovo Yoga Duet 7 properly
  ALSA: hda/realtek - ALC897 headset MIC no sound
  ALSA: usb-audio: US16x08: Move overflow check before array access
  ALSA: hda/realtek: Add mute LED quirk for HP Omen laptop

Add support for ethtool -p|--identify
by enabling blinking of the panel LED if supported by the NIC firmware.
Signed-off-by: Sixiang Chen <sixiang.chen@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220622083938.291548-1-simon.horman@corigine.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When a packet enters the OVS datapath and does not match any existing
flows installed in the kernel flow cache, the packet will be sent to
userspace to be parsed, and a new flow will be created. The kernel and
OVS rely on each other to parse packet fields in the same way so that
packets will be handled properly.

As per the design document linked below, OVS expects all later IPv6
fragments to have nw_proto=44 in the flow key, so they can be correctly
matched on OpenFlow rules. OpenFlow controllers create pipelines based
on this design.

This behavior was changed by the commit in the Fixes tag so that
nw_proto equals the next_header field of the last extension header.
However, there is no counterpart for this change in OVS userspace,
meaning that this field is parsed differently between OVS and the
kernel. This is a problem because OVS creates actions based on what is
parsed in userspace, but the kernel-provided flow key is used as a match
criteria, as described in Documentation/networking/openvswitch.rst. This
leads to issues such as packets incorrectly matching on a flow and thus
the wrong list of actions being applied to the packet. Such changes in
packet parsing cannot be implemented without breaking the userspace.

The offending commit is partially reverted to restore the expected
behavior.

The change technically made sense and there is a good reason that it was
implemented, but it does not comply with the original design of OVS.
If in the future someone wants to implement such a change, then it must
be user-configurable and disabled by default to preserve backwards
compatibility with existing OVS versions.

Cc: stable@vger.kernel.org
Fixes: fa642f08 ("openvswitch: Derive IP protocol number for IPv6 later frags")
Link: https://docs.openvswitch.org/en/latest/topics/design/#fragmentsSigned-off-by: Rosemarie O'Riorden <roriorden@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220621204845.9721-1-roriorden@redhat.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Commit 8a59f9d1 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()")
has moved the inet_csk_has_ulp(sk) check from sk_psock_init() to
the new tcp_bpf_update_proto() function. I'm guessing that this
was done to allow creating psocks for non-inet sockets.

Unfortunately the destruction path for psock includes the ULP
unwind, so we need to fail the sk_psock_init() itself.
Otherwise if ULP is already present we'll notice that later,
and call tcp_update_ulp() with the sk_proto of the ULP
itself, which will most likely result in the ULP looping
its callbacks.

Fixes: 8a59f9d1 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Tested-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/r/20220620191353.1184629-2-kuba@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

This reverts commit 69135c57.

This commit was just papering over the issue, ULP should not
get ->update() called with its own sk_prot. Each ULP would
need to add this check.

Fixes: 69135c57 ("net/tls: fix tls_sk_proto_close executed repeatedly")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20220620191353.1184629-1-kuba@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Tony Nguyen says:

====================
40GbE Intel Wired LAN Driver Updates 2022-06-21

This series contains updates to i40e driver only.

Mateusz adds support for using the speed option in ethtool.

Minghao Chi removes unneeded synchronize_irq() calls.

Bernard Zhao removes unneeded NULL check.

* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  intel/i40e: delete if NULL check before dev_kfree_skb
  i40e: Remove unnecessary synchronize_irq() before free_irq()
  i40e: Add support for ethtool -s <interface> speed <speed in Mb>
====================

Link: https://lore.kernel.org/r/20220621225930.632741-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The following sequence currently causes a driver bug warning
when using virtio_net:

  # ip link set eth0 up
  # echo mem > /sys/power/state (or e.g. # rtcwake -s 10 -m mem)
  <resume>
  # ip link set eth0 down

  Missing register, driver bug
  WARNING: CPU: 0 PID: 375 at net/core/xdp.c:138 xdp_rxq_info_unreg+0x58/0x60
  Call trace:
   xdp_rxq_info_unreg+0x58/0x60
   virtnet_close+0x58/0xac
   __dev_close_many+0xac/0x140
   __dev_change_flags+0xd8/0x210
   dev_change_flags+0x24/0x64
   do_setlink+0x230/0xdd0
   ...

This happens because virtnet_freeze() frees the receive_queue
completely (including struct xdp_rxq_info) but does not call
xdp_rxq_info_unreg(). Similarly, virtnet_restore() sets up the
receive_queue again but does not call xdp_rxq_info_reg().

Actually, parts of virtnet_freeze_down() and virtnet_restore_up()
are almost identical to virtnet_close() and virtnet_open(): only
the calls to xdp_rxq_info_(un)reg() are missing. This means that
we can fix this easily and avoid such problems in the future by
just calling virtnet_close()/open() from the freeze/restore handlers.

Aside from adding the missing xdp_rxq_info calls the only difference
is that the refill work is only cancelled if netif_running(). However,
this should not make any functional difference since the refill work
should only be active if the network interface is actually up.

Fixes: 754b8a21 ("virtio_net: setup xdp_rxq_info")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220621114845.3650258-1-stephan.gerhold@kernkonzept.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-06-21

This series contains updates to ice driver only.

Marcin fixes GTP filters by allowing ignoring of the inner ethertype field.

Wojciech adds VSI handle tracking in order to properly distinguish similar
filters for removal.

Anatolii removes ability to set 1000baseT and 1000baseX fields
concurrently which caused link issues. He also disallows setting
channels to less than the number of Traffic Classes which would cause
NULL pointer dereference.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  ice: ethtool: Prohibit improper channel config for DCB
  ice: ethtool: advertise 1000M speeds properly
  ice: Fix switchdev rules book keeping
  ice: ignore protocol field in GTP offload
====================

Link: https://lore.kernel.org/r/20220621224756.631765-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

saddr and daddr are set but not used.

Fixes: ba44f818 ("raw: use more conventional iterators")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220622032303.159394-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.

According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.

In addition to that, commit b6e0c419 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.

Fixes: b6e0c419 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add support multi-gigabit and single-port Ethernet
PHY transceiver (AQR113C).
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Link: https://lore.kernel.org/r/20220621034027.56508-1-vbhadram@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use the recently introduced mdiodev accessors for the lynx PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1o3Zd8-002yHI-G2@rmk-PC.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>