Add "fsl,spi-only-use-cs1-sel" to fit i.MX8DXL-EVK.
Spi common code does not support use of CS signals discontinuously.
It only uses CS1 without using CS0. So, add this property to re-config
chipselect value.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20200727031513.31774-1-xiaoning.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

The RXFLR is possible larger than rx_left in Rockchip SPI, fix it.

Fixes: 01b59ce5 ("spi: rockchip: use irq rather than polling")
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-3-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

The FIFO depth of SPI V2 is 64 instead of 32, add support for it.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-2-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

The burst length can be adjusted according to the transmission
length to improve the transmission rate
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-1-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

Before generic upgrade, both .suspend() and .resume() were invoking
pci_enable_wake(pci_dev, PCI_D3hot, 0). Hence, disabling wakeup in both
states. (Normal trend is .suspend() enables and .resume() disables the
wakeup.)

This was ambiguous and may be buggy. Instead of replicating the legacy
behavior, drop the wakeup-disable call.

Fixes: f185bcc7 ("spi: spi-topcliff-pch: use generic power management")
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200727172936.661567-1-vaibhavgupta40@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Simply copying all xfers from userspace into one bounce buffer causes
alignment problems if the SPI controller uses DMA.

Ensure that all transfer data blocks within the rx and tx bounce buffers
are aligned for DMA (according to ARCH_KMALLOC_MINALIGN).

Alignment may increase the usage of the bounce buffers. In some cases,
the buffers may need to be increased using the "bufsiz" module
parameter.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200728100832.24788-1-ceggers@arri.deSigned-off-by: Mark Brown <broonie@kernel.org>

Silence documentation build warnings by correcting kernel-doc comment
for spi_transfer struct.
Signed-off-by: Colton Lewis <colton.w.lewis@protonmail.com>
Link: https://lore.kernel.org/r/20200725050242.279548-1-colton.w.lewis@protonmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

The spi-sun4i driver already has the ability to do large transfers.
However, the max transfer size reported is still fifo depth - 1.

Update the max transfer size reported to the max value possible.

Fixes: 19673791 ("spi: sun4i: Allow transfers larger than FIFO size")
Signed-off-by: Jonathan Liu <net147@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200727072328.510798-1-net147@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Enable runtime pm support for spi-imx driver.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20200727063354.17031-1-xiaoning.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add a DT binding documentation for the MT8192 soc.
Signed-off-by: leilk.liu <leilk.liu@mediatek.com>
Link: https://lore.kernel.org/r/20200721122436.31544-1-leilk.liu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch add spi support for mt8192 IC.
Signed-off-by: leilk.liu <leilk.liu@mediatek.com>
Link: https://lore.kernel.org/r/20200721122436.31544-2-leilk.liu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support to SPI controller on Intel Atom based Lightning Mountain
SoC which reuses the Lantiq SPI controller IP.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/7d644e5d03ef534f719763e5c823c1673e53d1a5.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support to SPI controller on Intel Atom based Lightning Mountain SoC
which reuses Lantiq SPI controller IP.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/4d61a75381aca9479f9fc15d07a7b05534da6bb3.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Moving interrupt configuration to SoC specific data structure helps to add
support for newer SoCs on which SPI controller with lesser interrupt lines
compared to existing chipsets.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/7eb6d863515245fedfa0296c72082df107367d07.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

On newer chipsets, SPI controller has fifos of larger size.
So add the fifo size bit mask entry in SoC specific data structure.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/a0889abf17a9fbc7077f10be0f0342b7ebdf9361.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

On newer chipsets interrupt need to be acknowledged as they use
different interrupt controller which does not acknowledge the
interrupts automatically.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/608923b484d9ef239b44bb545c0b79b27030a6ae.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Address of Interrupt control registers are different on new chipsets.
So move them to SoC specific data structure.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/f0f9723a30ea9c2ee48d2199f7512af9e15803b0.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Existing driver supports only single core SoC. New multicore platforms uses
the same driver/IP so SMP support is required. This patch adds multicore
support in the driver.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/d6663296b41f102c582fda08e71f62b72ca05d5d.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

In full duplex mode, rx overflow error is observed. To overcome the error,
wait until the complete data got received and proceed further.

Fixes: 17f84b79 ("spi: lantiq-ssc: add support for Lantiq SSC SPI controller")
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/efb650b0faa49a00788c4e0ca8ef7196bdba851d.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.

With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.

This driver makes use of PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(), pci_enable_wake()
and pci_set_power_state() to do required operations. In generic mode, they
are no longer needed.

Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.

Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Link: https://lore.kernel.org/r/20200720155714.714114-1-vaibhavgupta40@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This converts the PPC4xx SPI driver to use GPIO descriptors.

The driver is already just picking some GPIOs from the device
tree so the conversion is pretty straight forward. However
this driver is looking form a pure "gpios" property rather
than the standard binding "cs-gpios" so we need to add a new
exception to the gpiolib OF parser to allow this for this
driver's compatibles.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20200714072226.26071-1-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The spi cadence driver should support spi-cs-high in mode bits
so that the peripherals that needs the chip select to be high active can
use it. Add the SPI-CS-HIGH flag in the supported mode bits.
Signed-off-by: Shreyas Joshi <shreyas.joshi@biamp.com>
Link: https://lore.kernel.org/r/20200710211655.1564-1-shreyas.joshi@biamp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Call the put function after probe successfully. Otherwise, the lpspi
module will keep active status until the first spi transfer called.

Disable runtime pm when probe fails. There is no need to active runtime
pm after probe failed.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20200714075251.12777-2-xiaoning.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series "Add support for [H]SCIF/TMU/CMT/THS/SDHI/MSIOF/CAN[FD]/I2C/IIC/RWDT on R8A774E1" from Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>:

Hi All,

This patch series enables support for following on RZ/G2H SoC,
* CPU OPP
* THS
* CMT/TMU
* I2C/IIC
* MSIOF
* RWDT
* SDHI
* SCIF/HSCIF
* CAN/CANFD

Cheers,
Prabhakar

Lad Prabhakar (14):
  dt-bindings: thermal: rcar-gen3-thermal: Add r8a774e1 support
  dt-bindings: timer: renesas,cmt: Document r8a774e1 CMT support
  arm64: dts: renesas: r8a774e1: Add SCIF and HSCIF nodes
  arm64: dts: renesas: r8a774e1: Add SDHI nodes
  dt-bindings: i2c: renesas,i2c: Document r8a774e1 support
  dt-bindings: i2c: renesas,iic: Document r8a774e1 support
  arm64: dts: renesas: r8a774e1: Add I2C and IIC-DVFS support
  dt-bindings: spi: renesas,sh-msiof: Add r8a774e1 support
  arm64: dts: renesas: r8a774e1: Add MSIOF nodes
  dt-bindings: watchdog: renesas,wdt: Document r8a774e1 support
  arm64: dts: renesas: r8a774e1: Add RWDT node
  dt-bindings: can: rcar_can: Document r8a774e1 support
  dt-bindings: can: rcar_canfd: Document r8a774e1 support
  arm64: dts: renesas: r8a774e1: Add CAN[FD] support

Marian-Cristian Rotariu (6):
  arm64: dts: renesas: r8a774e1: Add operating points
  thermal: rcar_gen3_thermal: Add r8a774e1 support
  arm64: dts: renesas: r8a774e1: Add RZ/G2H thermal support
  arm64: dts: renesas: r8a774e1: Add CMT device nodes
  dt-bindings: timer: renesas,tmu: Document r8a774e1 bindings
  arm64: dts: renesas: r8a774e1: Add TMU device nodes

 .../devicetree/bindings/i2c/renesas,i2c.txt   |   1 +
 .../devicetree/bindings/i2c/renesas,iic.txt   |   1 +
 .../devicetree/bindings/net/can/rcar_can.txt  |   1 +
 .../bindings/net/can/rcar_canfd.txt           |   1 +
 .../bindings/spi/renesas,sh-msiof.yaml        |   1 +
 .../bindings/thermal/rcar-gen3-thermal.yaml   |   1 +
 .../bindings/timer/renesas,cmt.yaml           |   2 +
 .../devicetree/bindings/timer/renesas,tmu.txt |   1 +
 .../bindings/watchdog/renesas,wdt.yaml        |   1 +
 arch/arm64/boot/dts/renesas/r8a774e1.dtsi     | 713 +++++++++++++++++-
 drivers/thermal/rcar_gen3_thermal.c           |   4 +
 11 files changed, 715 insertions(+), 12 deletions(-)

--
2.17.1

Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI,
struct 'spi_acpi_match' becomes defined but unused.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-amd.c:297:36: warning: ‘spi_acpi_match’ defined but not used [-Wunused-const-variable=]
 297 | static const struct acpi_device_id spi_acpi_match[] = {
 | ^~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Sanjay R Mehta <sanju.mehta@amd.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-15-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI,
struct 'pxa2xx_spi_acpi_match' becomes defined but unused.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-pxa2xx.c:1435:36: warning: ‘pxa2xx_spi_acpi_match’ defined but not used [-Wunused-const-variable=]
 1435 | static const struct acpi_device_id pxa2xx_spi_acpi_match[] = {
 | ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/20200717135424.2442271-14-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The only way this driver can be probed by MFD via its parent device.

No other reference to 'microchip,at91sam9g45-usart-spi' exists in the kernel.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-at91-usart.c:684:34: warning: ‘at91_usart_spi_dt_ids’ defined but not used [-Wunused-const-variable=]
 684 | static const struct of_device_id at91_usart_spi_dt_ids[] = {
 | ^~~~~~~~~~~~~~~~~~~~~
Suggested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Radu Pirea <radu_nicolae.pirea@upb.ro>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-13-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'io_base_addr' not described in 'pch_spi_data'
 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'pkt_tx_buff' not described in 'pch_spi_data'
 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'pkt_rx_buff' not described in 'pch_spi_data'
 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'dma' not described in 'pch_spi_data'
 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'use_dma' not described in 'pch_spi_data'
 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'save_total_len' not described in 'pch_spi_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200717135424.2442271-12-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-zynqmp-gqspi.c:205: warning: Function parameter or member 'slavecs' not described in 'zynqmp_gqspi_selectslave'
 drivers/spi/spi-zynqmp-gqspi.c:205: warning: Function parameter or member 'slavebus' not described in 'zynqmp_gqspi_selectslave'
 drivers/spi/spi-zynqmp-gqspi.c:205: warning: Excess function parameter 'flashcs' description in 'zynqmp_gqspi_selectslave'
 drivers/spi/spi-zynqmp-gqspi.c:205: warning: Excess function parameter 'flashbus' description in 'zynqmp_gqspi_selectslave'
 drivers/spi/spi-zynqmp-gqspi.c:902: warning: Function parameter or member 'dev' not described in 'zynqmp_qspi_suspend'
 drivers/spi/spi-zynqmp-gqspi.c:902: warning: Excess function parameter '_dev' description in 'zynqmp_qspi_suspend'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-11-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-zynq-qspi.c:143: warning: Function parameter or member 'dev' not described in 'zynq_qspi'
 drivers/spi/spi-zynq-qspi.c:334: warning: Function parameter or member 'spi' not described in 'zynq_qspi_config_op'
 drivers/spi/spi-zynq-qspi.c:334: warning: Excess function parameter 'qspi' description in 'zynq_qspi_config_op'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Cc: Sureshkumar Relli <nagasure@xilinx.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-10-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Also demote non-worthy kerneldoc headers to standard comment blocks.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-pl022.c:304: warning: cannot understand function prototype: 'enum ssp_writing '
 drivers/spi/spi-pl022.c:330: warning: Function parameter or member 'loopback' not described in 'vendor_data'
 drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'rx_lev_trig' not described in 'pl022'
 drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'tx_lev_trig' not described in 'pl022'
 drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'dma_running' not described in 'pl022'
 drivers/spi/spi-pl022.c:670: warning: Function parameter or member 'pl022' not described in 'readwriter'
 drivers/spi/spi-pl022.c:1250: warning: Function parameter or member 'irq' not described in 'pl022_interrupt_handler'
 drivers/spi/spi-pl022.c:1250: warning: Function parameter or member 'dev_id' not described in 'pl022_interrupt_handler'
 drivers/spi/spi-pl022.c:1343: warning: Function parameter or member 'pl022' not described in 'set_up_next_transfer'
 drivers/spi/spi-pl022.c:1343: warning: Function parameter or member 'transfer' not described in 'set_up_next_transfer'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Sachin Verma <sachin.verma@st.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-9-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-s3c64xx.c:150: warning: Function parameter or member 'quirks' not described in 's3c64xx_spi_port_config'
 drivers/spi/spi-s3c64xx.c:150: warning: Function parameter or member 'clk_ioclk' not described in 's3c64xx_spi_port_config'
 drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'pdev' not described in 's3c64xx_spi_driver_data'
 drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'rx_dma' not described in 's3c64xx_spi_driver_data'
 drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'tx_dma' not described in 's3c64xx_spi_driver_data'
 drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'port_conf' not described in 's3c64xx_spi_driver_data'
 drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'port_id' not described in 's3c64xx_spi_driver_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Andi Shyti <andi@etezian.org>
Cc: Jaswinder Singh <jassi.brar@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Link: https://lore.kernel.org/r/20200717135424.2442271-8-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Looks like it hasn't ever been checked.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-meson-spicc.c: In function ‘meson_spicc_reset_fifo’:
 drivers/spi/spi-meson-spicc.c:365:6: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
 365 | u32 data;
 | ^~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Link: https://lore.kernel.org/r/20200717135424.2442271-7-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-meson-spifc.c:80: warning: Function parameter or member 'dev' not described in 'meson_spifc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: linux-amlogic@lists.infradead.org
Link: https://lore.kernel.org/r/20200717135424.2442271-6-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

ep93xx_spi_read_write() changed is parameters, but the function
documentation was left unchanged.  Let's realign.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-ep93xx.c:227: warning: Function parameter or member 'master' not described in 'ep93xx_spi_read_write'
 drivers/spi/spi-ep93xx.c:227: warning: Excess function parameter 'espi' description in 'ep93xx_spi_read_write'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Link: https://lore.kernel.org/r/20200717135424.2442271-5-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-davinci.c:249: warning: Function parameter or member 'dspi' not described in 'davinci_spi_get_prescale'
 drivers/spi/spi-davinci.c:249: warning: Function parameter or member 'max_speed_hz' not described in 'davinci_spi_get_prescale'
 drivers/spi/spi-davinci.c:249: warning: Excess function parameter 'maxspeed_hz' description in 'davinci_spi_get_prescale'
 drivers/spi/spi-davinci.c:719: warning: Function parameter or member 'data' not described in 'dummy_thread_fn'
 drivers/spi/spi-davinci.c:719: warning: Excess function parameter 'context_data' description in 'dummy_thread_fn'
 drivers/spi/spi-davinci.c:735: warning: Function parameter or member 'data' not described in 'davinci_spi_irq'
 drivers/spi/spi-davinci.c:735: warning: Excess function parameter 'context_data' description in 'davinci_spi_irq'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200717135424.2442271-4-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

No attempt has been made to document any of the demoted functions here.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-bitbang.c:181: warning: Function parameter or member 'spi' not described in 'spi_bitbang_setup'
 drivers/spi/spi-bitbang.c:215: warning: Function parameter or member 'spi' not described in 'spi_bitbang_cleanup'
 drivers/spi/spi-bitbang.c:434: warning: Function parameter or member 'bitbang' not described in 'spi_bitbang_stop'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200717135424.2442271-3-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Kerneldoc function parameter descriptions must be in '@.*: ' format.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'spi' not described in 'spi_test_execute_msg'
 drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'test' not described in 'spi_test_execute_msg'
 drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'tx' not described in 'spi_test_execute_msg'
 drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'rx' not described in 'spi_test_execute_msg'
 drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'spi' not described in 'spi_test_run_test'
 drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'test' not described in 'spi_test_run_test'
 drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'tx' not described in 'spi_test_run_test'
 drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'rx' not described in 'spi_test_run_test'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: linux-spi@vger.kernel.org
Link: https://lore.kernel.org/r/20200717135424.2442271-2-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Document RZ/G2H (R8A774E1) SoC bindings.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1594811350-14066-15-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series "spi: bcm2835/bcm2835aux: support effective_speed_hz" from Marc Kleine-Budde <mkl@pengutronix.de>:

Hello,

I've picked up and forward ported Martin Sperl's patches which add support for
effective_speed_hz to the SPI controllers found on all raspberry pi models.

See the following patch, which adds this feature to the SPI core, for more
information:

    5d7e2b5e spi: core: allow reporting the effectivly used speed_hz for a transfer

regards,
Marc

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel