This patch fixes typos in drivers/net/wirless/rtlwifi/Kconfig.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This makes it possible to save some lines of code in drivers with an
simple bcma driver registration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

[ar5008 and ar9002]_hw_spur_mitigate have big portion of identical code.
This patch will move common part of ar5008_hw_spur_mitigate to
ar5008_hw_cmn_spur_mitigate and reuse it in ar9002_hw_spur_mitigate.

As noticed by Joe Perches I reuse ar9002_hw_spur_mitigate (const) version of
declarations for pilot_mask_reg and chan_mask_reg.

There should be no other difference with original code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Several of these drivers have there TX randomly blocked for 3~5 seconds while
measuring tx throughput (iperf). The root couse happens in rtl_pci_flush().
The function uses a while-loop to wait for TX queue length to decrease to 0.
The TX queue length counts the number of packets that are queued in the driver.
The driver relys on the TX OK interrupt to return skb and reduce TX queue length.

The interrupt subroutine disables interupts, reads the interrupt registers, and
then clears the registers in the beginning of _rtl_pci_interrupt(). After all
interupts process are finished, the driver invokes enable_interrupt() to enable
interupts. This behavior is normal for an interrupt subroutine.

But enable_interrupt() invokes clear_interrupt() again. This unexpected interrupt
clearing may cleari me fresh TX OK interrupts. These missing interrupts cause TX
queue length to never reduce to 0i, which causes rtl_pci_flush() to be stuck in
unterminated while-loop.

This patch removes clear_interrupt() in enable_interrupt() to avoid this behavior.
Signed-off-by: Vincent Fann <vincent_fann@realtek.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The driver was not setting a channel plan. Now it gets it from EEPROM.
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The driver is converted to use the channel plan in the EEPROM.
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The driver was setting a channel plan for the world. Now it reads it fromi
EEPROM.

In addition, a typo was fixed.
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The driver was setting a channel plan for the world. Now it reads it from
EEPROM.
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Driver rtlwifi maintains its own regulatory information, The Chrome Autotest
(https://www.chromium.org/chromium-os/testing/autotest-user-doc)
showed some errors. This patch adds the necessary information for rtlwifi.
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

These are used like:

	set_bit(WORK_LINK_UP, &priv->work_pending);

The problem is that set_bit() takes the actual bit number and not a mask
so static checkers get upset.  It doesn't affect run time because we do
it consistently, but we may as well clean it up.

Fixes: 6010ce07 ('rndis_wlan: do link-down state change in worker thread')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In d8a2c51c ('ath9k_htc: Use atomic operations for op_flags') we
changed things like this:

-	if (priv->op_flags & OP_TSF_RESET) {
+	if (test_bit(OP_TSF_RESET, &priv->op_flags)) {

The problem is that test_bit() takes a bit number and not a mask.  It
means that when we do:

	set_bit(OP_TSF_RESET, &priv->op_flags);

Then it sets the (1 << 6) bit instead of the 6 bit so we are setting a
bit which is past the end of the unsigned long.

Fixes: d8a2c51c ('ath9k_htc: Use atomic operations for op_flags')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

gcc-5.0 gained a new warning in the fwsignal portion of the brcmfmac
driver:

drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c: In function 'brcmf_fws_txs_process':
drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c:1478:8: warning: 'skb' may be used uninitialized in this function [-Wmaybe-uninitialized]

This is a false positive, and marking the brcmf_fws_hanger_poppkt function
as 'static inline' makes the warning go away. I have checked the object
file output and while a little code gets moved around, the size of
the binary remains identical.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added, and the assignments
as well as error checking fixed up.

API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/carl9170/usb.c:675
	int return assigned to unsigned long

Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_CARL9170=m

Patch is against 4.1-rc3 (localversion-next is -next-20150512)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch changes all debug print functions from dev_dbg/dev_err/dev_info
to mwifiex specific debug functions.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch is to add support for data hexdump debug feature.
It is controlled by level debug_mask in adapter structure.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support for debugging print control in mwifiex driver.

The debug level can be controlled via either by modules load parameter
debug_mask or by writing to debug_mask in debugfs file.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support for FW memory read/write operations via debugfs.
This is useful during debugging FW issues.

Examples:

For reading FW memory location:
echo r 0x01ac > /sys/kernel/debug/mwifiex/mlan0/memrw
cat /sys/kernel/debug/mwifiex/mlan0/memrw

For writing FW memory location:
echo w 0x01ac 0x55aa > /sys/kernel/debug/mwifiex/mlan0/memrw
Signed-off-by: Chin-ran Lo <crlo@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

During usage of the new Bluetooth driver for Realtek devices, it was found
that BT scans were inhibited for the RTL8723BE when wireless was active. The
exact cause of this interference is not known yet, but a satisfactory work
around has been found that does not seem to have any visible side effects.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Shao Fu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The PCI cache line size value was being compared against decimal values
prefixed with 0x.

Fixed the literals to use the correct hex values.

This has not been tested due to lack of hardware. However, the value in
`cline` is PCI cache line size, which is the CPU's cache line size.
It is less likely for cache line sizes to be 22 or 50, and more likely for
them to be 16 or 32. Also, as far as I understand, cache line size is used for
things like aligning DMA requests with CPU cache line, which improve
performance but wouldn't break anything if the value doesn't match. In
this case, we will fall through to the default case which leaves `reg`
unchanged.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch fixes these checkpatch.pl errors around a single switch-case
block:

ERROR: switch and case should be at the same indent
ERROR: trailing statements should be on next line

More specifically, the fix has been applied to the five occurances of
the errors listed below.

ERROR: switch and case should be at the same indent
#1100: FILE: adm8211.c:1100:
+               switch (cline) {
[...]
+                 default: reg |= (0x0 << 14);

ERROR: trailing statements should be on next line
#1101: FILE: adm8211.c:1101:
+               case  0x8: reg |= (0x1 << 14);

ERROR: trailing statements should be on next line
#1103: FILE: adm8211.c:1103:
+               case 0x16: reg |= (0x2 << 14);

ERROR: trailing statements should be on next line
#1105: FILE: adm8211.c:1105:
+               case 0x32: reg |= (0x3 << 14);

ERROR: trailing statements should be on next line
#1107: FILE: adm8211.c:1107:
+                 default: reg |= (0x0 << 14);
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ACPI will manage WiFi chip's power state during suspend/resume
process on some tablet platforms(such as ASUS T100TA). This is
not supported by brcmfmac driver now, and the context of WiFi
chip will be damaged after resume. This patch informs ACPI not
to manage WiFi chip's power state.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

parameter "infra_mode" of rtl92c_init_beacon_max_error() is not used.
so i remove this.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Initialization routine set REG_BCN_MAX_ERR to 0xFF.
also _rtl92cu_set_media_status set REG_BCN_MAX_ERR to same value.
so i remove this code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Lauri Kenttä <lauri.kentta@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Major changes:

ath10k:

* qca6174 power consumption improvements, enable ASPM etc (Michal)

wil6210:

* support Wi-Fi Simple Configuration in STA mode

Add support for flashing 10GBaseT adapter with BCM 84834 PHY and
Aquantia AQ1202 PHY.

Updating of the PHY firmware must happen before the INITIALIZE_CMD.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add two more eBPF test cases for JITs, i.e. the second one revealed a
bug in the x86_64 JIT compiler, where only an int3 filled image from
the allocator was emitted and later wrongly set by the compiler as the
bpf_func program code since optimization pass boundary was surpassed
w/o actually emitting opcodes.

Interpreter:

  [   45.782892] test_bpf: #242 BPF_MAXINSNS: Very long jump backwards jited:0 11 PASS
  [   45.783062] test_bpf: #243 BPF_MAXINSNS: Edge hopping nuthouse jited:0 14705 PASS

After x86_64 JIT (fixed):

  [   80.495638] test_bpf: #242 BPF_MAXINSNS: Very long jump backwards jited:1 6 PASS
  [   80.495957] test_bpf: #243 BPF_MAXINSNS: Edge hopping nuthouse jited:1 17157 PASS

Reference: http://thread.gmane.org/gmane.linux.network/364729Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver updates 2015-05-22

The following patches are included in this driver update series:

- Retrieve and set an additional hardware feature setting
- Fix the initial mode/speed determination when auto-negotiation is
  disabled
- Add additional netif_dbg support to the driver

This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Change more netdev_dbg statements over to netif_dbg and add some new
netif_dbg statements to the driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the ethtool command is used to set the speed of the device while
the device is down, the check to set the initial mode may fail when
the device is brought up, causing failure to bring the device up.

Update the code to set the initial mode based on the desired speed if
auto-negotiation is disabled.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The device private data structure contains all the defined hardware
features for the device. However one of the features is not set. Even
though the feature is not currently used, set it to avoid future
issues of the feature being checked thinking it has been properly set.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send icmp pmtu error if we find that the largest fragment of df-skb
exceeded the output path mtu.

The ip output path will still catch this later on but we can avoid the
forward/postrouting hook traversal by rejecting right away.

This is what ipv6 already does.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hannes Frederic Sowa says:

====================
net: af_unix: zerocopy stream bits

This series implements zerocopy support for AF_UNIX SOCK_STREAM sockets.

Changelog in the specific patches. Thanks to all the reviewers!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

unix_stream_recvmsg is refactored to unix_stream_read_generic in this
patch and enhanced to deal with pipe splicing. The refactoring is
inneglible, we mostly have to deal with a non-existing struct msghdr
argument.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepare skb_splice_bits to be able to deal with AF_UNIX sockets.

AF_UNIX sockets don't use lock_sock/release_sock and thus we have to
use a callback to make the locking and unlocking configureable.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements sendpage support for AF_UNIX SOCK_STREAM
sockets. This is also required for a complete splice implementation.

The implementation is a bit tricky because we append to already existing
skbs and so have to hold unix_sk->readlock to protect the reading side
from either advancing UNIXCB.consumed or freeing the skb at the socket
receive tail.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2015-05-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
ath10k:

* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware

ath9k:

* spectral scan: add support for multiple FFT frames per report

iwlwifi:

* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure

brcmfmac:

* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4: Enable single ported VFs over IB ports

This series further enhances the support for mlx4 single ported VFs
introduced in 3.15 to work over IB ports too.

Just as quick reminder, the ConnectX3 device family exposes one PCI device
which serves both ports.

This can be non-optimal under virtualization schemes where the admin
would like the VF to expose one interface to the VM, etc.

Since all the VF interaction with the firmware passes through the PF
driver, we can emulate to the VF they have one port, and further create
a set of the VFs which act on port1 of the device and another set which
acts on port2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the limitation that disallows configuring single ported VFs
in the presence of IB ports, after addressing the issues that
prevented that to work.

SMI (QP0) requests/responses are still not supported for single
ported IB VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>