- 01 Feb, 2024 21 commits
-
-
Benjamin Poirier authored
Similar to commit dd2d40ac ("selftests: bonding: Add more missing config options"), add more networking-specific config options which are needed for team device tests. For testing, I used the minimal config generated by virtme-ng and I added the options in the config file. Afterwards, the team device test passed. Fixes: bbb774d9 ("net: Add tests for bonding and team address list management") Reviewed-by:
Petr Machata <petrm@nvidia.com> Signed-off-by:
Benjamin Poirier <bpoirier@nvidia.com> Link: https://lore.kernel.org/r/20240131140848.360618-2-bpoirier@nvidia.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Souradeep Chakrabarti authored
In commit ac504767 ("hv_netvsc: Disable NAPI before closing the VMBus channel"), napi_disable was getting called for all channels, including all subchannels without confirming if they are enabled or not. This caused hv_netvsc getting hung at napi_disable, when netvsc_probe() has finished running but nvdev->subchan_work has not started yet. netvsc_subchan_work() -> rndis_set_subchannel() has not created the sub-channels and because of that netvsc_sc_open() is not running. netvsc_remove() calls cancel_work_sync(&nvdev->subchan_work), for which netvsc_subchan_work did not run. netif_napi_add() sets the bit NAPI_STATE_SCHED because it ensures NAPI cannot be scheduled. Then netvsc_sc_open() -> napi_enable will clear the NAPIF_STATE_SCHED bit, so it can be scheduled. napi_disable() does the opposite. Now during netvsc_device_remove(), when napi_disable is called for those subchannels, napi_disable gets stuck on infinite msleep. This fix addresses this problem by ensuring that napi_disable() is not getting called for non-enabled NAPI struct. But netif_napi_del() is still necessary for these non-enabled NAPI struct for cleanup purpose. Call trace: [ 654.559417] task:modprobe state:D stack: 0 pid: 2321 ppid: 1091 flags:0x00004002 [ 654.568030] Call Trace: [ 654.571221] <TASK> [ 654.573790] __schedule+0x2d6/0x960 [ 654.577733] schedule+0x69/0xf0 [ 654.581214] schedule_timeout+0x87/0x140 [ 654.585463] ? __bpf_trace_tick_stop+0x20/0x20 [ 654.590291] msleep+0x2d/0x40 [ 654.593625] napi_disable+0x2b/0x80 [ 654.597437] netvsc_device_remove+0x8a/0x1f0 [hv_netvsc] [ 654.603935] rndis_filter_device_remove+0x194/0x1c0 [hv_netvsc] [ 654.611101] ? do_wait_intr+0xb0/0xb0 [ 654.615753] netvsc_remove+0x7c/0x120 [hv_netvsc] [ 654.621675] vmbus_remove+0x27/0x40 [hv_vmbus] Cc: stable@vger.kernel.org Fixes: ac504767 ("hv_netvsc: Disable NAPI before closing the VMBus channel") Signed-off-by:
Souradeep Chakrabarti <schakrabarti@linux.microsoft.com> Reviewed-by:
Dexuan Cui <decui@microsoft.com> Reviewed-by:
Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by:
Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/1706686551-28510-1-git-send-email-schakrabarti@linux.microsoft.comSigned-off-by:
-
Jan Beulich authored
Invoking the make_tx_response() / push_tx_responses() pair with no lock held would be acceptable only if all such invocations happened from the same context (NAPI instance or dealloc thread). Since this isn't the case, and since the interface "spec" also doesn't demand that multicast operations may only be performed with no in-flight transmits, MCAST_{ADD,DEL} processing also needs to acquire the response lock around the invocations. To prevent similar mistakes going forward, "downgrade" the present functions to private helpers of just the two remaining ones using them directly, with no forward declarations anymore. This involves renaming what so far was make_tx_response(), for the new function of that name to serve the new (wrapper) purpose. While there, - constify the txp parameters, - correct xenvif_idx_release()'s status parameter's type, - rename {,_}make_tx_response()'s status parameters for consistency with xenvif_idx_release()'s. Fixes: 210c34dc ("xen-netback: add support for multicast control") Cc: stable@vger.kernel.org Signed-off-by:Jan Beulich <jbeulich@suse.com> Reviewed-by:
Paul Durrant <paul@xen.org> Link: https://lore.kernel.org/r/980c6c3d-e10e-4459-8565-e8fbde122f00@suse.comSigned-off-by:
-
Breno Leitao authored
The documentation is pointing to the wrong path for the interface. Documentation is pointing to /sys/class/<iface>, instead of /sys/class/net/<iface>. Fix it by adding the `net/` directory before the interface. Fixes: 1a02ef76 ("net: sysfs: add documentation entries for /sys/class/<iface>/queues") Signed-off-by:
Breno Leitao <leitao@debian.org> Link: https://lore.kernel.org/r/20240131102150.728960-2-leitao@debian.orgSigned-off-by:
-
Geetha sowjanya authored
XDP queues are created/destroyed when a XDP program is attached/detached. In current driver xdp_queues are not getting destroyed on program exit due to incorrect xdp_queue and tot_tx_queue count values. This patch fixes the issue by setting tot_tx_queue and xdp_queue count to correct values. It also fixes xdp.data_hard_start address. Fixes: 06059a1a ("octeontx2-pf: Add XDP support to netdev PF") Signed-off-by:
Geetha sowjanya <gakula@marvell.com> Link: https://lore.kernel.org/r/20240130120610.16673-1-gakula@marvell.comSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Jakub Kicinski authored
Paolo Abeni says: ==================== selftests: net: a few pmtu.sh fixes This series try to address CI failures for the pmtu.sh tests. It does _not_ attempt to enable all the currently skipped cases, to avoid adding more entropy. Tested with: make -C tools/testing/selftests/ TARGETS=net install vng --build --config tools/testing/selftests/net/config vng --run . --user root -- \ ./tools/testing/selftests/kselftest_install/run_kselftest.sh \ -t net:pmtu.sh ==================== Link: https://lore.kernel.org/r/cover.1706635101.git.pabeni@redhat.comSigned-off-by:
-
Paolo Abeni authored
When running the pmtu.sh via the kselftest infra, accessing /dev/stdout gives unexpected results: # dd: failed to open '/dev/stdout': Device or resource busy # TEST: IPv4, bridged vxlan4: PMTU exceptions [FAIL] Let dd use directly the standard output to fix the above: # TEST: IPv4, bridged vxlan4: PMTU exceptions - nexthop objects [ OK ] Fixes: 136a1b43 ("selftests: net: test vxlan pmtu exceptions with tcp") Signed-off-by:
Guillaume Nault <gnault@redhat.com> Reviewed-by:
David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/23d7592c5d77d75cff9b34f15c227f92e911c2ae.1706635101.git.pabeni@redhat.comSigned-off-by:
-
Paolo Abeni authored
The pmtu.sh test tries to detect the tunnel protocols available in the running kernel and properly skip the unsupported cases. In a few more complex setup, such detection is unsuccessful, as the script currently ignores some intermediate error code at setup time. Before: # which: no nettest in (/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin) # TEST: vti6: PMTU exceptions (ESP-in-UDP) [FAIL] # PMTU exception wasn't created after creating tunnel exceeding link layer MTU # ./pmtu.sh: line 931: kill: (7543) - No such process # ./pmtu.sh: line 931: kill: (7544) - No such process After: # xfrm4 not supported # TEST: vti4: PMTU exceptions [SKIP] Fixes: ece1278a ("selftests: net: add ESP-in-UDP PMTU test") Signed-off-by:
-
Paolo Abeni authored
The mentioned test uses a few Kconfig still missing the net config, add them. Before: # Error: Specified qdisc kind is unknown. # Error: Specified qdisc kind is unknown. # Error: Qdisc not classful. # We have an error talking to the kernel # Error: Qdisc not classful. # We have an error talking to the kernel # policy_routing not supported # TEST: ICMPv4 with DSCP and ECN: PMTU exceptions [SKIP] After: # TEST: ICMPv4 with DSCP and ECN: PMTU exceptions [ OK ] Fixes: ec730c3e ("selftest: net: Test IPv4 PMTU exceptions with DSCP and ECN") Signed-off-by:
-
Jakub Kicinski authored
Brett Creeley says: ==================== pds_core: Various fixes This series includes the following changes: There can be many users of the pds_core's adminq. This includes pds_core's uses and any clients that depend on it. When the pds_core device goes through a reset for any reason the adminq is freed and reconfigured. There are some gaps in the current implementation that will cause crashes during reset if any of the previously mentioned users of the adminq attempt to use it after it's been freed. Issues around how resets are handled, specifically regarding the driver's error handlers. Originally these patches were aimed at net-next, but it was requested to push the fixes patches to net. The original patches can be found here: https://lore.kernel.org/netdev/20240126174255.17052-1-brett.creeley@amd.com/ Also, the Reviewed-by tags were left in place from net-next reviews as the patches didn't change. ==================== Link: https://lore.kernel.org/r/20240129234035.69802-1-brett.creeley@amd.comSigned-off-by:
-
Brett Creeley authored
Currently the teardown/setup flow for driver probe/remove is quite a bit different from the reset flows in pdsc_fw_down()/pdsc_fw_up(). One key piece that's missing are the calls to pci_alloc_irq_vectors() and pci_free_irq_vectors(). The pcie reset case is calling pci_free_irq_vectors() on reset_prepare, but not calling the corresponding pci_alloc_irq_vectors() on reset_done. This is causing unexpected/unwanted interrupt behavior due to the adminq interrupt being accidentally put into legacy interrupt mode. Also, the pci_alloc_irq_vectors()/pci_free_irq_vectors() functions are being called directly in probe/remove respectively. Fix this inconsistency by making the following changes: 1. Always call pdsc_dev_init() in pdsc_setup(), which calls pci_alloc_irq_vectors() and get rid of the now unused pds_dev_reinit(). 2. Always free/clear the pdsc->intr_info in pdsc_teardown() since this structure will get re-alloced in pdsc_setup(). 3. Move the calls of pci_free_irq_vectors() to pdsc_teardown() since pci_alloc_irq_vectors() will always be called in pdsc_setup()->pdsc_dev_init() for both the probe/remove and reset flows. 4. Make sure to only create the debugfs "identity" entry when it doesn't already exist, which it will in the reset case because it's already been created in the initial call to pdsc_dev_init(). Fixes: ffa55858 ("pds_core: implement pci reset handlers") Signed-off-by:Brett Creeley <brett.creeley@amd.com> Reviewed-by:
Shannon Nelson <shannon.nelson@amd.com> Link: https://lore.kernel.org/r/20240129234035.69802-7-brett.creeley@amd.comSigned-off-by:
-
Brett Creeley authored
During reset the BARs might be accessed when they are unmapped. This can cause unexpected issues, so fix it by clearing the cached BAR values so they are not accessed until they are re-mapped. Also, make sure any places that can access the BARs when they are NULL are prevented. Fixes: 49ce92fb ("pds_core: add FW update feature to devlink") Signed-off-by:
Przemek Kitszel <przemyslaw.kitszel@intel.com> Link: https://lore.kernel.org/r/20240129234035.69802-6-brett.creeley@amd.comSigned-off-by:
-
Brett Creeley authored
There are multiple paths that can result in using the pdsc's adminq. [1] pdsc_adminq_isr and the resulting work from queue_work(), i.e. pdsc_work_thread()->pdsc_process_adminq() [2] pdsc_adminq_post() When the device goes through reset via PCIe reset and/or a fw_down/fw_up cycle due to bad PCIe state or bad device state the adminq is destroyed and recreated. A NULL pointer dereference can happen if [1] or [2] happens after the adminq is already destroyed. In order to fix this, add some further state checks and implement reference counting for adminq uses. Reference counting was used because multiple threads can attempt to access the adminq at the same time via [1] or [2]. Additionally, multiple clients (i.e. pds-vfio-pci) can be using [2] at the same time. The adminq_refcnt is initialized to 1 when the adminq has been allocated and is ready to use. Users/clients of the adminq (i.e. [1] and [2]) will increment the refcnt when they are using the adminq. When the driver goes into a fw_down cycle it will set the PDSC_S_FW_DEAD bit and then wait for the adminq_refcnt to hit 1. Setting the PDSC_S_FW_DEAD before waiting will prevent any further adminq_refcnt increments. Waiting for the adminq_refcnt to hit 1 allows for any current users of the adminq to finish before the driver frees the adminq. Once the adminq_refcnt hits 1 the driver clears the refcnt to signify that the adminq is deleted and cannot be used. On the fw_up cycle the driver will once again initialize the adminq_refcnt to 1 allowing the adminq to be used again. Fixes: 01ba61b5 ("pds_core: Add adminq processing and commands") Signed-off-by: -
Brett Creeley authored
The initial design for the adminq interrupt was done based on client drivers having their own adminq and adminq interrupt. So, each client driver's adminq isr would use their specific adminqcq for the private data struct. For the time being the design has changed to only use a single adminq for all clients. So, instead use the struct pdsc for the private data to simplify things a bit. This also has the benefit of not dereferencing the adminqcq to access the pdsc struct when the PDSC_S_STOPPING_DRIVER bit is set and the adminqcq has actually been cleared/freed. Fixes: 01ba61b5 ("pds_core: Add adminq processing and commands") Signed-off-by:
-
Brett Creeley authored
There is a small window where pdsc_work_thread() calls pdsc_process_adminq() and pdsc_process_adminq() passes the PDSC_S_STOPPING_DRIVER check and starts to process adminq/notifyq work and then the driver starts a fw_down cycle. This could cause some undefined behavior if the notifyqcq/adminqcq are free'd while pdsc_process_adminq() is running. Use cancel_work_sync() on the adminqcq's work struct to make sure any pending work items are cancelled and any in progress work items are completed. Also, make sure to not call cancel_work_sync() if the work item has not be initialized. Without this, traces will happen in cases where a reset fails and teardown is called again or if reset fails and the driver is removed. Fixes: 01ba61b5 ("pds_core: Add adminq processing and commands") Signed-off-by:
-
Brett Creeley authored
The PCIe reset handlers can run at the same time as the health thread. This can cause the health thread to stomp on the PCIe reset. Fix this by preventing the health thread from running while a PCIe reset is happening. As part of this use timer_shutdown_sync() during reset and remove to make sure the timer doesn't ever get rearmed. Fixes: ffa55858 ("pds_core: implement pci reset handlers") Signed-off-by:
-
Eric Dumazet authored
syzbot reported a lockdep splat [1]. Blamed commit hinted about the possible lockdep violation, and code used unix_state_lock_nested() in an attempt to silence lockdep. It is not sufficient, because unix_state_lock_nested() is already used from unix_state_double_lock(). We need to use a separate subclass. This patch adds a distinct enumeration to make things more explicit. Also use swap() in unix_state_double_lock() as a clean up. v2: add a missing inline keyword to unix_state_lock_nested() [1] WARNING: possible circular locking dependency detected 6.8.0-rc1-syzkaller-00356-g8a696a29 #0 Not tainted syz-executor.1/2542 is trying to acquire lock: ffff88808b5df9e8 (rlock-AF_UNIX){+.+.}-{2:2}, at: skb_queue_tail+0x36/0x120 net/core/skbuff.c:3863 but task is already holding lock: ffff88808b5dfe70 (&u->lock/1){+.+.}-{2:2}, at: unix_dgram_sendmsg+0xfc7/0x2200 net/unix/af_unix.c:2089 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&u->lock/1){+.+.}-{2:2}: lock_acquire+0x1e3/0x530 kernel/locking/lockdep.c:5754 _raw_spin_lock_nested+0x31/0x40 kernel/locking/spinlock.c:378 sk_diag_dump_icons net/unix/diag.c:87 [inline] sk_diag_fill+0x6ea/0xfe0 net/unix/diag.c:157 sk_diag_dump net/unix/diag.c:196 [inline] unix_diag_dump+0x3e9/0x630 net/unix/diag.c:220 netlink_dump+0x5c1/0xcd0 net/netlink/af_netlink.c:2264 __netlink_dump_start+0x5d7/0x780 net/netlink/af_netlink.c:2370 netlink_dump_start include/linux/netlink.h:338 [inline] unix_diag_handler_dump+0x1c3/0x8f0 net/unix/diag.c:319 sock_diag_rcv_msg+0xe3/0x400 netlink_rcv_skb+0x1df/0x430 net/netlink/af_netlink.c:2543 sock_diag_rcv+0x2a/0x40 net/core/sock_diag.c:280 netlink_unicast_kernel net/netlink/af_netlink.c:1341 [inline] netlink_unicast+0x7e6/0x980 net/netlink/af_netlink.c:1367 netlink_sendmsg+0xa37/0xd70 net/netlink/af_netlink.c:1908 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] sock_write_iter+0x39a/0x520 net/socket.c:1160 call_write_iter include/linux/fs.h:2085 [inline] new_sync_write fs/read_write.c:497 [inline] vfs_write+0xa74/0xca0 fs/read_write.c:590 ksys_write+0x1a0/0x2c0 fs/read_write.c:643 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b -> #0 (rlock-AF_UNIX){+.+.}-{2:2}: check_prev_add kernel/locking/lockdep.c:3134 [inline] check_prevs_add kernel/locking/lockdep.c:3253 [inline] validate_chain+0x1909/0x5ab0 kernel/locking/lockdep.c:3869 __lock_acquire+0x1345/0x1fd0 kernel/locking/lockdep.c:5137 lock_acquire+0x1e3/0x530 kernel/locking/lockdep.c:5754 __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0xd5/0x120 kernel/locking/spinlock.c:162 skb_queue_tail+0x36/0x120 net/core/skbuff.c:3863 unix_dgram_sendmsg+0x15d9/0x2200 net/unix/af_unix.c:2112 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] ____sys_sendmsg+0x592/0x890 net/socket.c:2584 ___sys_sendmsg net/socket.c:2638 [inline] __sys_sendmmsg+0x3b2/0x730 net/socket.c:2724 __do_sys_sendmmsg net/socket.c:2753 [inline] __se_sys_sendmmsg net/socket.c:2750 [inline] __x64_sys_sendmmsg+0xa0/0xb0 net/socket.c:2750 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&u->lock/1); lock(rlock-AF_UNIX); lock(&u->lock/1); lock(rlock-AF_UNIX); *** DEADLOCK *** 1 lock held by syz-executor.1/2542: #0: ffff88808b5dfe70 (&u->lock/1){+.+.}-{2:2}, at: unix_dgram_sendmsg+0xfc7/0x2200 net/unix/af_unix.c:2089 stack backtrace: CPU: 1 PID: 2542 Comm: syz-executor.1 Not tainted 6.8.0-rc1-syzkaller-00356-g8a696a29 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x1e7/0x2d0 lib/dump_stack.c:106 check_noncircular+0x366/0x490 kernel/locking/lockdep.c:2187 check_prev_add kernel/locking/lockdep.c:3134 [inline] check_prevs_add kernel/locking/lockdep.c:3253 [inline] validate_chain+0x1909/0x5ab0 kernel/locking/lockdep.c:3869 __lock_acquire+0x1345/0x1fd0 kernel/locking/lockdep.c:5137 lock_acquire+0x1e3/0x530 kernel/locking/lockdep.c:5754 __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0xd5/0x120 kernel/locking/spinlock.c:162 skb_queue_tail+0x36/0x120 net/core/skbuff.c:3863 unix_dgram_sendmsg+0x15d9/0x2200 net/unix/af_unix.c:2112 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] ____sys_sendmsg+0x592/0x890 net/socket.c:2584 ___sys_sendmsg net/socket.c:2638 [inline] __sys_sendmmsg+0x3b2/0x730 net/socket.c:2724 __do_sys_sendmmsg net/socket.c:2753 [inline] __se_sys_sendmmsg net/socket.c:2750 [inline] __x64_sys_sendmmsg+0xa0/0xb0 net/socket.c:2750 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b RIP: 0033:0x7f26d887cda9 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 e1 20 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f26d95a60c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000133 RAX: ffffffffffffffda RBX: 00007f26d89abf80 RCX: 00007f26d887cda9 RDX: 000000000000003e RSI: 00000000200bd000 RDI: 0000000000000004 RBP: 00007f26d88c947a R08: 0000000000000000 R09: 0000000000000000 R10: 00000000000008c0 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000000000b R14: 00007f26d89abf80 R15: 00007ffcfe081a68 Fixes: 2aac7a2c ("unix_diag: Pending connections IDs NLA") Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Reviewed-by:
Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20240130184235.1620738-1-edumazet@google.comSigned-off-by:
-
Jakub Kicinski authored
Dmitry Safonov says: ==================== selftests/net: A couple of typos fixes in key-management/rst tests Two typo fixes, noticed by Mohammad's review. And a fix for an issue that got uncovered. v1: https://lore.kernel.org/r/20240118-tcp-ao-test-key-mgmt-v1-0-3583ca147113@arista.comSigned-off-by:
Dmitry Safonov <dima@arista.com> ==================== Link: https://lore.kernel.org/r/20240130-tcp-ao-test-key-mgmt-v2-0-d190430a6c60@arista.comSigned-off-by:
-
Dmitry Safonov authored
Currently, the test is racy and seems to not pass anymore. In order to rectify it, aim on TCP_TW_RST. Doesn't seem way too good with this sleep() part, but it seems as a reasonable compromise for the test. There is a plan in-line comment on how-to improve it, going to do it on the top, at this moment I want it to run on netdev/patchwork selftests dashboard. It also slightly changes tcp_ao-lib in order to get SO_ERROR propagated to test_client_verify() return value. Fixes: c6df7b23 ("selftests/net: Add TCP-AO RST test") Signed-off-by:
-
Dmitry Safonov authored
As the names of (struct test_key) members didn't reflect whether the key was used for TX or RX, the verification for the counters was done incorrectly for asymmetrical selftests. Rename these with _tx appendix and fix checks in verify_counters(). While at it, as the checks are now correct, introduce skip_counters_checks, which is intended for tests where it's expected that a key that was set with setsockopt(sk, IPPROTO_TCP, TCP_AO_INFO, ...) might had no chance of getting used on the wire. Fixes the following failures, exposed by the previous commit: > not ok 51 server: Check current != rnext keys set before connect(): Counter pkt_good was expected to increase 0 => 0 for key 132:5 > not ok 52 server: Check current != rnext keys set before connect(): Counter pkt_good was not expected to increase 0 => 21 for key 137:10 > > not ok 63 server: Check current flapping back on peer's RnextKey request: Counter pkt_good was expected to increase 0 => 0 for key 132:5 > not ok 64 server: Check current flapping back on peer's RnextKey request: Counter pkt_good was not expected to increase 0 => 40 for key 137:10 Cc: Mohammad Nassiri <mnassiri@ciena.com> Fixes: 3c3ead55 ("selftests/net: Add TCP-AO key-management test") Signed-off-by:
-
Mohammad Nassiri authored
The end_server() function only operates in the server thread and always takes an accept socket instead of a listen socket as its input argument. To align with this, invert the boolean values used when calling verify_counters() within the end_server() function. As a result of this typo, the test didn't correctly check for the non-symmetrical scenario, where i.e. peer-A uses a key <100:200> to send data, but peer-B uses another key <105:205> to send its data. So, in simple words, different keys for TX and RX. Fixes: 3c3ead55 ("selftests/net: Add TCP-AO key-management test") Signed-off-by:
Mohammad Nassiri <mnassiri@ciena.com> Link: https://lore.kernel.org/all/934627c5-eebb-4626-be23-cfb134c01d1a@arista.com/ [amended 'Fixes' tag, added the issue description and carried-over to lkml] Signed-off-by:
-
- 31 Jan, 2024 8 commits
-
-
Andrew Lunn authored
Not all mv88e6xxx device support C45 read/write operations. Those which do not return -EOPNOTSUPP. However, when phylib scans the bus, it considers this fatal, and the probe of the MDIO bus fails, which in term causes the mv88e6xxx probe as a whole to fail. When there is no device on the bus for a given address, the pull up resistor on the data line results in the read returning 0xffff. The phylib core code understands this when scanning for devices on the bus. C45 allows multiple devices to be supported at one address, so phylib will perform a few reads at each address, so although thought not the most efficient solution, it is a way to avoid fatal errors. Make use of this as a minimal fix for stable to fix the probing problems. Follow up patches will rework how C45 operates to make it similar to C22 which considers -ENODEV as a none-fatal, and swap mv88e6xxx to using this. Cc: stable@vger.kernel.org Fixes: 743a19e3 ("net: dsa: mv88e6xxx: Separate C22 and C45 transactions") Reported-by:
Tim Menninger <tmenninger@purestorage.com> Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240129224948.1531452-1-andrew@lunn.chSigned-off-by:
-
Zhipeng Lu authored
When inetdev_valid_mtu fails, cork->opt should be freed if it is allocated in ip_setup_cork. Otherwise there could be a memleak. Fixes: 501a90c9 ("inet: protect against too small mtu values.") Signed-off-by:
Zhipeng Lu <alexious@zju.edu.cn> Reviewed-by:
-
Andrew Halaney authored
Bhupesh's email responds indicating they've changed employers and with no new contact information. Let's drop the line from MAINTAINERS to avoid getting the same response over and over. Signed-off-by:
Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240129-remove-dwmac-qcom-ethqos-reviewer-v1-1-2645eab61451@redhat.comSigned-off-by:
-
Matthias May authored
l2_tos_ttl_inherit.sh verifies the inheritance of tos and ttl for GRETAP, VXLAN and GENEVE. Before testing it checks if the required module is available and if not skips the tests accordingly. Currently only GRETAP and VXLAN are tested because the GENEVE module is missing. Fixes: b690842d ("selftests/net: test l2 tunnel TOS/TTL inheriting") Signed-off-by:
Matthias May <matthias.may@westermo.com> Link: https://lore.kernel.org/r/20240130101157.196006-1-matthias.may@westermo.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueJakub Kicinski authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-01-29 (e1000e, ixgbe) This series contains updates to e1000e and ixgbe drivers. Jake corrects values used for maximum frequency adjustment for e1000e. Christophe Jaillet adjusts error handling path so that semaphore is released on ixgbe. * '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ixgbe: Fix an error handling path in ixgbe_read_iosf_sb_reg_x550() e1000e: correct maximum frequency adjustment values ==================== Link: https://lore.kernel.org/r/20240129185240.787397-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Parav Pandit authored
When port function state change is requested, and when the driver does not support it, it refers to the hw address attribute instead of state attribute. Seems like a copy paste error. Fix it by referring to the port function state attribute. Fixes: c0bea69d ("devlink: Validate port function request") Signed-off-by:
Parav Pandit <parav@nvidia.com> Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/20240129191059.129030-1-parav@nvidia.comSigned-off-by:
-
Linus Lüssing authored
The original idea of the delay_time check was to not apply multicast snooping too early when an MLD querier appears. And to instead wait at least for MLD reports to arrive before switching from flooding to group based, MLD snooped forwarding, to avoid temporary packet loss. However in a batman-adv mesh network it was noticed that after 248 days of uptime 32bit MIPS based devices would start to signal that they had stopped applying multicast snooping due to missing queriers - even though they were the elected querier and still sending MLD queries themselves. While time_is_before_jiffies() generally is safe against jiffies wrap-arounds, like the code comments in jiffies.h explain, it won't be able to track a difference larger than ULONG_MAX/2. With a 32bit large jiffies and one jiffies tick every 10ms (CONFIG_HZ=100) on these MIPS devices running OpenWrt this would result in a difference larger than ULONG_MAX/2 after 248 (= 2^32/100/60/60/24/2) days and time_is_before_jiffies() would then start to return false instead of true. Leading to multicast snooping not being applied to multicast packets anymore. Fix this issue by using a proper timer_list object which won't have this ULONG_MAX/2 difference limitation. Fixes: b00589af ("bridge: disable snooping if there is no querier") Signed-off-by:
Linus Lüssing <linus.luessing@c0d3.blue> Acked-by:
Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20240127175033.9640-1-linus.luessing@c0d3.blueSigned-off-by:
-
Ido Schimmel authored
One of the test cases in the test_bridge_backup_port.sh selftest relies on a matchall classifier to drop unrelated traffic so that the Tx drop counter on the VXLAN device will only be incremented as a result of traffic generated by the test. However, the configuration option for the matchall classifier is missing from the configuration file which might explain the failures we see in the netdev CI [1]. Fix by adding CONFIG_NET_CLS_MATCHALL to the configuration file. [1] # Backup nexthop ID - invalid IDs # ------------------------------- [...] # TEST: Forwarding out of vx0 [ OK ] # TEST: No forwarding using backup nexthop ID [ OK ] # TEST: Tx drop increased [FAIL] # TEST: IPv6 address family nexthop as backup nexthop [ OK ] # TEST: No forwarding out of swp1 [ OK ] # TEST: Forwarding out of vx0 [ OK ] # TEST: No forwarding using backup nexthop ID [ OK ] # TEST: Tx drop increased [FAIL] [...] Fixes: b4084530 ("selftests: net: Add bridge backup port and backup nexthop ID test") Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Acked-by:
-
- 30 Jan, 2024 7 commits
-
-
Eric Dumazet authored
syzbot reported an interesting trace [1] caused by a stale sk->sk_wq pointer in a closed llc socket. In commit ff7b11aa ("net: socket: set sock->sk to NULL after calling proto_ops::release()") Eric Biggers hinted that some protocols are missing a sock_orphan(), we need to perform a full audit. In net-next, I plan to clear sock->sk from sock_orphan() and amend Eric patch to add a warning. [1] BUG: KASAN: slab-use-after-free in list_empty include/linux/list.h:373 [inline] BUG: KASAN: slab-use-after-free in waitqueue_active include/linux/wait.h:127 [inline] BUG: KASAN: slab-use-after-free in sock_def_write_space_wfree net/core/sock.c:3384 [inline] BUG: KASAN: slab-use-after-free in sock_wfree+0x9a8/0x9d0 net/core/sock.c:2468 Read of size 8 at addr ffff88802f4fc880 by task ksoftirqd/1/27 CPU: 1 PID: 27 Comm: ksoftirqd/1 Not tainted 6.8.0-rc1-syzkaller-00049-g6098d87e #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xd9/0x1b0 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:377 [inline] print_report+0xc4/0x620 mm/kasan/report.c:488 kasan_report+0xda/0x110 mm/kasan/report.c:601 list_empty include/linux/list.h:373 [inline] waitqueue_active include/linux/wait.h:127 [inline] sock_def_write_space_wfree net/core/sock.c:3384 [inline] sock_wfree+0x9a8/0x9d0 net/core/sock.c:2468 skb_release_head_state+0xa3/0x2b0 net/core/skbuff.c:1080 skb_release_all net/core/skbuff.c:1092 [inline] napi_consume_skb+0x119/0x2b0 net/core/skbuff.c:1404 e1000_unmap_and_free_tx_resource+0x144/0x200 drivers/net/ethernet/intel/e1000/e1000_main.c:1970 e1000_clean_tx_irq drivers/net/ethernet/intel/e1000/e1000_main.c:3860 [inline] e1000_clean+0x4a1/0x26e0 drivers/net/ethernet/intel/e1000/e1000_main.c:3801 __napi_poll.constprop.0+0xb4/0x540 net/core/dev.c:6576 napi_poll net/core/dev.c:6645 [inline] net_rx_action+0x956/0xe90 net/core/dev.c:6778 __do_softirq+0x21a/0x8de kernel/softirq.c:553 run_ksoftirqd kernel/softirq.c:921 [inline] run_ksoftirqd+0x31/0x60 kernel/softirq.c:913 smpboot_thread_fn+0x660/0xa10 kernel/smpboot.c:164 kthread+0x2c6/0x3a0 kernel/kthread.c:388 ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:242 </TASK> Allocated by task 5167: kasan_save_stack+0x33/0x50 mm/kasan/common.c:47 kasan_save_track+0x14/0x30 mm/kasan/common.c:68 unpoison_slab_object mm/kasan/common.c:314 [inline] __kasan_slab_alloc+0x81/0x90 mm/kasan/common.c:340 kasan_slab_alloc include/linux/kasan.h:201 [inline] slab_post_alloc_hook mm/slub.c:3813 [inline] slab_alloc_node mm/slub.c:3860 [inline] kmem_cache_alloc_lru+0x142/0x6f0 mm/slub.c:3879 alloc_inode_sb include/linux/fs.h:3019 [inline] sock_alloc_inode+0x25/0x1c0 net/socket.c:308 alloc_inode+0x5d/0x220 fs/inode.c:260 new_inode_pseudo+0x16/0x80 fs/inode.c:1005 sock_alloc+0x40/0x270 net/socket.c:634 __sock_create+0xbc/0x800 net/socket.c:1535 sock_create net/socket.c:1622 [inline] __sys_socket_create net/socket.c:1659 [inline] __sys_socket+0x14c/0x260 net/socket.c:1706 __do_sys_socket net/socket.c:1720 [inline] __se_sys_socket net/socket.c:1718 [inline] __x64_sys_socket+0x72/0xb0 net/socket.c:1718 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xd3/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b Freed by task 0: kasan_save_stack+0x33/0x50 mm/kasan/common.c:47 kasan_save_track+0x14/0x30 mm/kasan/common.c:68 kasan_save_free_info+0x3f/0x60 mm/kasan/generic.c:640 poison_slab_object mm/kasan/common.c:241 [inline] __kasan_slab_free+0x121/0x1b0 mm/kasan/common.c:257 kasan_slab_free include/linux/kasan.h:184 [inline] slab_free_hook mm/slub.c:2121 [inline] slab_free mm/slub.c:4299 [inline] kmem_cache_free+0x129/0x350 mm/slub.c:4363 i_callback+0x43/0x70 fs/inode.c:249 rcu_do_batch kernel/rcu/tree.c:2158 [inline] rcu_core+0x819/0x1680 kernel/rcu/tree.c:2433 __do_softirq+0x21a/0x8de kernel/softirq.c:553 Last potentially related work creation: kasan_save_stack+0x33/0x50 mm/kasan/common.c:47 __kasan_record_aux_stack+0xba/0x100 mm/kasan/generic.c:586 __call_rcu_common.constprop.0+0x9a/0x7b0 kernel/rcu/tree.c:2683 destroy_inode+0x129/0x1b0 fs/inode.c:315 iput_final fs/inode.c:1739 [inline] iput.part.0+0x560/0x7b0 fs/inode.c:1765 iput+0x5c/0x80 fs/inode.c:1755 dentry_unlink_inode+0x292/0x430 fs/dcache.c:400 __dentry_kill+0x1ca/0x5f0 fs/dcache.c:603 dput.part.0+0x4ac/0x9a0 fs/dcache.c:845 dput+0x1f/0x30 fs/dcache.c:835 __fput+0x3b9/0xb70 fs/file_table.c:384 task_work_run+0x14d/0x240 kernel/task_work.c:180 exit_task_work include/linux/task_work.h:38 [inline] do_exit+0xa8a/0x2ad0 kernel/exit.c:871 do_group_exit+0xd4/0x2a0 kernel/exit.c:1020 __do_sys_exit_group kernel/exit.c:1031 [inline] __se_sys_exit_group kernel/exit.c:1029 [inline] __x64_sys_exit_group+0x3e/0x50 kernel/exit.c:1029 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xd3/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b The buggy address belongs to the object at ffff88802f4fc800 which belongs to the cache sock_inode_cache of size 1408 The buggy address is located 128 bytes inside of freed 1408-byte region [ffff88802f4fc800, ffff88802f4fcd80) The buggy address belongs to the physical page: page:ffffea0000bd3e00 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x2f4f8 head:ffffea0000bd3e00 order:3 entire_mapcount:0 nr_pages_mapped:0 pincount:0 anon flags: 0xfff00000000840(slab|head|node=0|zone=1|lastcpupid=0x7ff) page_type: 0xffffffff() raw: 00fff00000000840 ffff888013b06b40 0000000000000000 0000000000000001 raw: 0000000000000000 0000000080150015 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected page_owner tracks the page as allocated page last allocated via order 3, migratetype Reclaimable, gfp_mask 0xd20d0(__GFP_IO|__GFP_FS|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC|__GFP_RECLAIMABLE), pid 4956, tgid 4956 (sshd), ts 31423924727, free_ts 0 set_page_owner include/linux/page_owner.h:31 [inline] post_alloc_hook+0x2d0/0x350 mm/page_alloc.c:1533 prep_new_page mm/page_alloc.c:1540 [inline] get_page_from_freelist+0xa28/0x3780 mm/page_alloc.c:3311 __alloc_pages+0x22f/0x2440 mm/page_alloc.c:4567 __alloc_pages_node include/linux/gfp.h:238 [inline] alloc_pages_node include/linux/gfp.h:261 [inline] alloc_slab_page mm/slub.c:2190 [inline] allocate_slab mm/slub.c:2354 [inline] new_slab+0xcc/0x3a0 mm/slub.c:2407 ___slab_alloc+0x4af/0x19a0 mm/slub.c:3540 __slab_alloc.constprop.0+0x56/0xa0 mm/slub.c:3625 __slab_alloc_node mm/slub.c:3678 [inline] slab_alloc_node mm/slub.c:3850 [inline] kmem_cache_alloc_lru+0x379/0x6f0 mm/slub.c:3879 alloc_inode_sb include/linux/fs.h:3019 [inline] sock_alloc_inode+0x25/0x1c0 net/socket.c:308 alloc_inode+0x5d/0x220 fs/inode.c:260 new_inode_pseudo+0x16/0x80 fs/inode.c:1005 sock_alloc+0x40/0x270 net/socket.c:634 __sock_create+0xbc/0x800 net/socket.c:1535 sock_create net/socket.c:1622 [inline] __sys_socket_create net/socket.c:1659 [inline] __sys_socket+0x14c/0x260 net/socket.c:1706 __do_sys_socket net/socket.c:1720 [inline] __se_sys_socket net/socket.c:1718 [inline] __x64_sys_socket+0x72/0xb0 net/socket.c:1718 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xd3/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b page_owner free stack trace missing Memory state around the buggy address: ffff88802f4fc780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88802f4fc800: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff88802f4fc880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88802f4fc900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88802f4fc980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: 43815482 ("net: sock_def_readable() and friends RCU conversion") Reported-and-tested-by: syzbot+32b89eaa102b372ff76d@syzkaller.appspotmail.com Signed-off-by:
-
Paolo Abeni authored
Esben Haabendal says: ==================== net: stmmac: dwmac-imx: Time Based Scheduling support This small patch series allows using TBS support of the i.MX Ethernet QOS controller for etf qdisc offload. It achieves this in a similar manner that it is done in dwmac-intel.c, dwmac-mediatek.c and stmmac_pci.c. Changes since v1: - Simplified for loop by starting at index 1. - Fixed problem with indentation. ==================== Link: https://lore.kernel.org/r/cover.1706256158.git.esben@geanix.comSigned-off-by:
-
Esben Haabendal authored
TSO and TBS cannot coexist. For now we set i.MX Ethernet QOS controller to use the first TX queue with TSO and the rest for TBS. TX queues with TBS can support etf qdisc hw offload. Signed-off-by:
Esben Haabendal <esben@geanix.com> Reviewed-by:
Kurt Kanzenbach <kurt@linutronix.de> Reviewed-by:
Vadim Fedorenko <vadim.fedorenko@linux.dev> Signed-off-by:
-
Esben Haabendal authored
With the dma conf being reallocated on each call to stmmac_open(), any information in there is lost, unless we specifically handle it. The STMMAC_TBS_EN bit is set when adding an etf qdisc, and the etf qdisc therefore would stop working when link was set down and then back up. Fixes: ba39b344 ("net: ethernet: stmicro: stmmac: generate stmmac dma conf before open") Cc: stable@vger.kernel.org Signed-off-by:
-
Helge Deller authored
On a parisc64 kernel I sometimes notice this kernel warning: Kernel unaligned access to 0x40ff8814 at ndisc_send_skb+0xc0/0x4d8 The address 0x40ff8814 points to the in6addr_linklocal_allrouters variable and the warning simply means that some ipv6 function tries to read a 64-bit word directly from the not-64-bit aligned in6addr_linklocal_allrouters variable. Unaligned accesses are non-critical as the architecture or exception handlers usually will fix it up at runtime. Nevertheless it may trigger a performance penality for some architectures. For details read the "unaligned-memory-access" kernel documentation. The patch below ensures that the ipv6 loopback and router addresses will always be naturally aligned. This prevents the unaligned accesses for all architectures. Signed-off-by:
Helge Deller <deller@gmx.de> Fixes: 034dfc5d ("ipv6: export in6addr_loopback to modules") Acked-by:
-
Jakub Kicinski authored
Modern OSes use iptables implementation with nf_tables as a backend, e.g.: $ iptables -V iptables v1.8.8 (nf_tables) Pablo points out that we need CONFIG_NFT_COMPAT to make that work, otherwise we see a lot of: Warning: Extension DNAT revision 0 not supported, missing kernel module? with DNAT being just an example here, other modules we need include udp, TTL, length etc. Link: https://lore.kernel.org/r/20240126201308.2903602-1-kuba@kernel.orgSigned-off-by:
-
Michal Vokáč authored
When working with GPIO, its direction must be set either when the GPIO is requested by gpiod_get*() or later on by one of the gpiod_direction_*() functions. Neither of this is done here which results in undefined behavior on some systems. As the reset GPIO is used right after it is requested here, it makes sense to configure it as GPIOD_OUT_HIGH right away. With that, the following gpiod_set_value_cansleep(1) becomes redundant and can be safely removed. Fixes: a653f2f5 ("net: dsa: qca8k: introduce reset via gpio feature") Signed-off-by:
Michal Vokáč <michal.vokac@ysoft.com> Reviewed-by:
-
- 29 Jan, 2024 4 commits
-
-
Christophe JAILLET authored
All error handling paths, except this one, go to 'out' where release_swfw_sync() is called. This call balances the acquire_swfw_sync() call done at the beginning of the function. Branch to the error handling path in order to correctly release some resources in case of error. Fixes: ae14a1d8 ("ixgbe: Fix IOSF SB access issues") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Jacob Keller authored
The e1000e driver supports hardware with a variety of different clock speeds, and thus a variety of different increment values used for programming its PTP hardware clock. The values currently programmed in e1000e_ptp_init are incorrect. In particular, only two maximum adjustments are used: 24000000 - 1, and 600000000 - 1. These were originally intended to be used with the 96 MHz clock and the 25 MHz clock. Both of these values are actually slightly too high. For the 96 MHz clock, the actual maximum value that can safely be programmed is 23,999,938. For the 25 MHz clock, the maximum value is 599,999,904. Worse, several devices use a 24 MHz clock or a 38.4 MHz clock. These parts are incorrectly assigned one of either the 24million or 600million values. For the 24 MHz clock, this is not a significant issue: its current increment value can support an adjustment up to 7billion in the positive direction. However, the 38.4 KHz clock uses an increment value which can only support up to 230,769,157 before it starts overflowing. To understand where these values come from, consider that frequency adjustments have the form of: new_incval = base_incval + (base_incval * adjustment) / (unit of adjustment) The maximum adjustment is reported in terms of parts per billion: new_incval = base_incval + (base_incval * adjustment) / 1 billion The largest possible adjustment is thus given by the following: max_incval = base_incval + (base_incval * max_adj) / 1 billion Re-arranging to solve for max_adj: max_adj = (max_incval - base_incval) * 1 billion / base_incval We also need to ensure that negative adjustments cannot underflow. This can be achieved simply by ensuring max_adj is always less than 1 billion. Introduce new macros in e1000.h codifying the maximum adjustment in PPB for each frequency given its associated increment values. Also clarify where these values come from by commenting about the above equations. Replace the switch statement in e1000e_ptp_init with one which mirrors the increment value switch statement from e1000e_get_base_timinica. For each device, assign the appropriate maximum adjustment based on its frequency. Some parts can have one of two frequency modes as determined by E1000_TSYNCRXCTL_SYSCFI. Since the new flow directly matches the assignments in e1000e_get_base_timinca, and uses well defined macro names, it is much easier to verify that the resulting maximum adjustments are correct. It also avoids difficult to parse construction such as the "hw->mac.type < e1000_phc_lpt", and the use of fallthrough which was especially confusing when combined with a conditional block. Note that I believe the current increment value configuration used for 24MHz clocks is sub-par, as it leaves at least 3 extra bits available in the INCVALUE register. However, fixing that requires more careful review of the clock rate and associated values. Reported-by:
Trey Harrison <harrisondigitalmedia@gmail.com> Fixes: 68fe1d5d ("e1000e: Add Support for 38.4MHZ frequency") Fixes: d89777bf ("e1000e: add support for IEEE-1588 PTP") Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
Naama Meir <naamax.meir@linux.intel.com> Signed-off-by:
-
Eric Dumazet authored
TCP rx zerocopy intent is to map pages initially allocated from NIC drivers, not pages owned by a fs. This patch adds to can_map_frag() these additional checks: - Page must not be a compound one. - page->mapping must be NULL. This fixes the panic reported by ZhangPeng. syzbot was able to loopback packets built with sendfile(), mapping pages owned by an ext4 file to TCP rx zerocopy. r3 = socket$inet_tcp(0x2, 0x1, 0x0) mmap(&(0x7f0000ff9000/0x4000)=nil, 0x4000, 0x0, 0x12, r3, 0x0) r4 = socket$inet_tcp(0x2, 0x1, 0x0) bind$inet(r4, &(0x7f0000000000)={0x2, 0x4e24, @multicast1}, 0x10) connect$inet(r4, &(0x7f00000006c0)={0x2, 0x4e24, @empty}, 0x10) r5 = openat$dir(0xffffffffffffff9c, &(0x7f00000000c0)='./file0\x00', 0x181e42, 0x0) fallocate(r5, 0x0, 0x0, 0x85b8) sendfile(r4, r5, 0x0, 0x8ba0) getsockopt$inet_tcp_TCP_ZEROCOPY_RECEIVE(r4, 0x6, 0x23, &(0x7f00000001c0)={&(0x7f0000ffb000/0x3000)=nil, 0x3000, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}, &(0x7f0000000440)=0x40) r6 = openat$dir(0xffffffffffffff9c, &(0x7f00000000c0)='./file0\x00', 0x181e42, 0x0) Fixes: 93ab6cc6 ("tcp: implement mmap() for zero copy receive") Link: https://lore.kernel.org/netdev/5106a58e-04da-372a-b836-9d3d0bd2507b@huawei.com/T/Reported-and-bisected-by:ZhangPeng <zhangpeng362@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Fedor Pchelkin authored
rx_data_reassembly skb is stored during NCI data exchange for processing fragmented packets. It is dropped only when the last fragment is processed or when an NTF packet with NCI_OP_RF_DEACTIVATE_NTF opcode is received. However, the NCI device may be deallocated before that which leads to skb leak. As by design the rx_data_reassembly skb is bound to the NCI device and nothing prevents the device to be freed before the skb is processed in some way and cleaned, free it on the NCI device cleanup. Found by Linux Verification Center (linuxtesting.org) with Syzkaller. Fixes: 6a2968aa ("NFC: basic NCI protocol implementation") Cc: stable@vger.kernel.org Reported-by: syzbot+6b7c68d9c21e4ee4251b@syzkaller.appspotmail.com Closes: https://lore.kernel.org/lkml/000000000000f43987060043da7b@google.com/Signed-off-by:
Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by:
-
