- 08 Jun, 2021 34 commits
-
-
Eugen Hristev authored
Add bindings for the Microchip eXtended Image Sensor Controller. Based on the atmel,isc.yaml binding. Signed-off-by:
Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-
Eugen Hristev authored
Convert the Atmel ISC to yaml binding format. Signed-off-by:
-
Eugen Hristev authored
Remove a duplicate definition of clock max divider Signed-off-by:
-
Eugen Hristev authored
Add support for additional formats supported by newer pipelines, and for additional pipeline modules. Signed-off-by:
-
Eugen Hristev authored
Add additional fields for registers present in sama7g5 type pipeline. Extend register masks for additional bits in sama7g5 type pipeline registers. Signed-off-by:
-
Eugen Hristev authored
Once the pipeline is set in the base code, create a callback that will adapt the ISC pipeline to each product. Create the adapt_pipeline callback that will be used in this fashion. [hverkuil: made isc_sama5d2_adapt_pipeline static] Signed-off-by:
-
Eugen Hristev authored
The list of input and output formats has to be product specific. Move this list into the product specific code. Have pointers to these arrays inside the device struct. Signed-off-by:
-
Eugen Hristev authored
The RLP submodule is a part of the atmel-isc pipeline, and stands for Rounding,Limiting and Packaging. It used to extract specific data from the ISC pipeline. For example if we want to output greyscale 8 bit, we would use limiting to 8 bits, and packaging to Luma component only. Create a product specific callback for initializing the RLP submodule of the pipeline [hverkuil: made isc_sama5d2_config_rlp static] Signed-off-by:
-
Eugen Hristev authored
The GAM submodule is a part of the atmel-isc pipeline, and stands for Gamma Correction. It is used to apply the gamma curve to the incoming pixels. Create a product specific callback for initializing the GAM submodule of the pipeline. For sama5d2 product, there is no special configuration at this moment, thus this function is a noop. [hverkuil: made isc_sama5d2_config_gam static] Signed-off-by:
-
Eugen Hristev authored
The DPC submodule is a part of the atmel-isc pipeline, and stands for Defective Pixel Correction. Its purpose is to detect defective pixels and correct them if possible with the help of adjacent pixels. Create a product specific callback for initializing the DPC submodule of the pipeline. For sama5d2 product, this module does not exist, thus this function is a noop. [hverkuil: made isc_sama5d2_config_dpc static] Signed-off-by:
-
Eugen Hristev authored
Create product specific callback for initializing v4l2 controls. Call this from v4l2 controls init function. [hverkuil: made isc_sama5d2_config_ctrls static] Signed-off-by:
-
Eugen Hristev authored
The CC submodule is a part of the atmel-isc pipeline, and stands for Color Correction. It is used to apply gains and offsets to the chroma (U, V) components of the YUV elements. Implement the CC submodule initialization, as a product specific function, which currently configures the neutral point in color correction. [hverkuil: made isc_sama5d2_config_cc static] Signed-off-by:
-
Eugen Hristev authored
Newer ISC pipelines have the additional modules of Defective Pixel Correction -> DPC itself, Defective Pixel Correction -> Green Disparity Correction (DPC_GDC) Defective Pixel Correction -> Black Level Correction (DPC_BLC) Vertical and Horizontal Scaler -> VHXS Some products have this full pipeline (sama7g5), other products do not (sama5d2) Add the modules to the isc base, and also extend the register range to include the modules. Signed-off-by:
-
Eugen Hristev authored
Add register description for additional pipeline modules: the Defective Pixel Correction (DPC) and the Vertical and Horizontal Scaler(VHXS) Signed-off-by:
-
Eugen Hristev authored
Add his_entry to the reg offsets struct. This will allow different products to have a different reg offset for this particular module. Signed-off-by:
-
Eugen Hristev authored
Add support for version register and print it at probe time. Signed-off-by:
-
Eugen Hristev authored
The DMA submodule is a part of the atmel-isc pipeline, and stands for Direct Memory Access. It acts like a master on the AXI bus of the SoC, and can directly write the RAM area with the pixel data from the ISC internal sram. Add dma to the reg offsets struct. This will allow different products to have a different reg offset for this particular module. Signed-off-by:
-
Eugen Hristev authored
The HIS submodule is a part of the atmel-isc pipeline, and stands for Histogram. This module performs a color histogram that can be read and used by the main processor. Add his to the reg offsets struct. This will allow different products to have a different reg offset for this particular module. Signed-off-by:
-
Eugen Hristev authored
The RLP submodule is a part of the atmel-isc pipeline, and stands for Rounding,Limiting and Packaging. It used to extract specific data from the ISC pipeline. For example if we want to output greyscale 8 bit, we would use limiting to 8 bits, and packaging to Luma component only. Add rlp to the reg offsets struct. This will allow different products to have a different reg offset for this particular module. Signed-off-by:
-
Eugen Hristev authored
The SUB submodules are a part of the atmel-isc pipeline, and stand for Subsampling. They are used to subsample the original YUV 4:4:4 pixel ratio aspect to either 4:2:2 or 4:2:0. Add sub420 and sub422 to the reg offsets struct. This will allow different products to have a different reg offset for these particular modules. Signed-off-by:
-
Eugen Hristev authored
The CBC submodule is a part of the atmel-isc pipeline, and stands for Contrast Brightness Control. It is used to apply gains and offsets to the luma (Y) and chroma (U, V) components of the YUV elements. Add cbc to the reg offsets struct. This will allow different products to have a different reg offset for this particular module. Signed-off-by:
-
Eugen Hristev authored
The CBC submodule is a part of the atmel-isc pipeline, and stands for Contrast Brightness Control. It is used to apply gains and offsets to the luma (Y) and chroma (U, V) components of the YUV elements. The CBC submodule should be initialized in the product specific driver as it's product specific. Other products can implement it differently [hverkuil: made isc_sama5d2_config_cbc static] Signed-off-by:
-
Eugen Hristev authored
Create a struct that holds register offsets that are product specific. Add initially the CSC register. This allows each product that contains a variant of the ISC to add their own register offset. Signed-off-by:
-
Eugen Hristev authored
Add the clock id to the debug message regarding clock setup Signed-off-by:
-
Eugen Hristev authored
The CSC submodule is a part of the atmel-isc pipeline, and stands for Color Space Conversion. It is used to apply a matrix transformation to RGB pixels to convert them to the YUV components. The CSC submodule should be initialized in the product specific driver as it's product specific. Other products can implement it differently. [hverkuil: made isc_sama5d2_config_csc static] Signed-off-by:
-
Eugen Hristev authored
The dma configuration (DCFG) is specific to the product. Move this configuration in the product specific driver, and add the field inside the driver struct. Signed-off-by:
-
Eugen Hristev authored
Move the max width and max height constants to the product specific driver and have them in the device struct. Signed-off-by:
-
Eugen Hristev authored
When calling the subdev, certain subdev drivers will overwrite the frame size and adding sizes which are beyond the ISC's capabilities. Thus we need to ensure the frame size is cropped to the maximum caps. Signed-off-by:
-
Eugen Hristev authored
The driver name constant must defined based on product driver, thus moving the constant directly where it's required. This will allow each ISC based product to define it's own name. Signed-off-by:
-
Eugen Hristev authored
Separate the gamma table from the isc base file into the specific sama5d2 product file. Add a pointer to the gamma table and entries count inside the platform driver specific struct. [hverkuil: made isc_sama5d2_gamma_table static] Signed-off-by:
-
John Cox authored
sps_max_sub_layers_minus1 is needed if the driver wishes to determine whether or not a frame might be used for reference. Signed-off-by:
John Cox <jc@kynesim.co.uk> Reviewed-by:
Benjamin Gaignard <benjamin.gaignard@collabora.com> Signed-off-by:
-
Tomi Valkeinen authored
Use the new vb2_queue_change_type() function in .vidioc_reqbufs and .vidioc_create_bufs instead of changing the queue type manually in vidioc_s_fmt_vbi_cap() and vidioc_s_fmt_sliced_vbi_cap(). This allows for a more consistent behavior, as .vidioc_reqbufs and .vidioc_create_bufs are when the queue will become "busy". Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by:
-
Tomi Valkeinen authored
Vivid tracks the VBI capture mode in vivid_dev->stream_sliced_vbi_cap field. We can just look at the buffer type instead, and drop the field. Signed-off-by:
-
Tomi Valkeinen authored
On some platforms a video device can capture either video data or metadata. The driver can implement vidioc functions for both video and metadata, and use a single vb2_queue for the buffers. However, vb2_queue requires choosing a single buffer type, which conflicts with the idea of capturing either video or metadata. The buffer type of vb2_queue can be changed, but it's not obvious how this should be done in the drivers. To help this, add a new helper function vb2_queue_change_type() which ensures the correct checks and documents how it can be used. Signed-off-by:
-
- 04 Jun, 2021 6 commits
-
-
Mauro Carvalho Chehab authored
There are several comments on this driver using those chars: - U+2013 ('–'): EN DASH - U+2018 ('‘'): LEFT SINGLE QUOTATION MARK - U+2019 ('’'): RIGHT SINGLE QUOTATION MARK They probably came from cut-and-pasting some texts found elsewhere. While there's nothing wrong on having those on comments in C, it is better to use ASCII chars for those specific cases, as the current variant doesn't really add any value. Signed-off-by: -
Mauro Carvalho Chehab authored
Instead of using U+2013 ('–'): EN DASH, let's just use an hyphen there, as this was probably introduced by some cut-and-paste from some other place. Signed-off-by: -
Mauro Carvalho Chehab authored
There are two spaces on a comment there, being one of them an U+00a0 (' '): NO-BREAK SPACE. Drop it. Signed-off-by: -
Mauro Carvalho Chehab authored
While there's nothing wrong with EN DASH on C code, this probably came from some cut-and paste from an ITU-T table. It sounds better to just an HYPHEN here. Reviewed-by:
Michael Tretter <m.tretter@pengutronix.de> Signed-off-by:
-
Mauro Carvalho Chehab authored
Instead of using: - U+00a0 (' '): NO-BREAK SPACE Use a normal white space. This was probably introduced by some cut-and-paste. Signed-off-by: -
Mauro Carvalho Chehab authored
Replace the occurences of the following character: - U+2019 ('’'): RIGHT SINGLE QUOTATION MARK By a normal single comma character. Signed-off-by:
-
