- 01 Oct, 2020 40 commits
-
-
Colin Ian King authored
[ Upstream commit a7463e2d ] The shifting of buf[3] by 24 bits to the left will be promoted to a 32 bit signed int and then sign-extended to an unsigned long. In the unlikely event that the the top bit of buf[3] is set then all then all the upper bits end up as also being set because of the sign-extension and this affect the ev->post_bit_error sum. Fix this by using the temporary u32 variable bit_error to avoid the sign-extension promotion. This also removes the need to do the computation twice. Addresses-Coverity: ("Unintended sign extension") Fixes: 267897a4 ("[media] tda10071: implement DVBv5 statistics") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Howard Chung authored
[ Upstream commit 96298f64 ] According to Core Spec Version 5.2 | Vol 3, Part A 6.1.5, the incoming L2CAP_ConfigReq should be handled during OPEN state. The section below shows the btmon trace when running L2CAP/COS/CFD/BV-12-C before and after this change. === Before === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 #22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 #23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 #24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 #25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 #27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 #28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 #29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 #30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 #31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ...... < ACL Data TX: Handle 256 flags 0x00 dlen 14 #32 L2CAP: Command Reject (0x01) ident 3 len 6 Reason: Invalid CID in request (0x0002) Destination CID: 64 Source CID: 65 > HCI Event: Number of Completed Packets (0x13) plen 5 #33 Num handles: 1 Handle: 256 Count: 1 ... === After === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 #22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 #23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 #24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 #25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 #27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 #28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 #29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 #30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 #31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ..... < ACL Data TX: Handle 256 flags 0x00 dlen 18 #32 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 < ACL Data TX: Handle 256 flags 0x00 dlen 12 #33 L2CAP: Configure Request (0x04) ident 3 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 #34 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #35 Num handles: 1 Handle: 256 Count: 1 ... Signed-off-by:
Howard Chung <howardchung@google.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Sagar Biradar authored
[ Upstream commit bef18d30 ] Fixes the occasional adapter panic when sg_reset is issued with -d, -t, -b and -H flags. Removal of command type HBA_IU_TYPE_SCSI_TM_REQ in aac_hba_send since iu_type, request_id and fib_flags are not populated. Device and target reset handlers are made to send TMF commands only when reset_state is 0. Link: https://lore.kernel.org/r/1581553771-25796-1-git-send-email-Sagar.Biradar@microchip.comReviewed-by:
Sagar Biradar <Sagar.Biradar@microchip.com> Signed-off-by:
Balsundar P <balsundar.p@microsemi.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Wen Gong authored
[ Upstream commit 402f2992 ] When use command to read values, it crashed. command: dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value count=1 bs=4 skip=$((0x100233)) It will call to ath10k_sdio_hif_diag_read with address = 0x4008cc and buf_len = 4. Then system crash: [ 1786.013258] Unable to handle kernel paging request at virtual address ffffffc00bd45000 [ 1786.013273] Mem abort info: [ 1786.013281] ESR = 0x96000045 [ 1786.013291] Exception class = DABT (current EL), IL = 32 bits [ 1786.013299] SET = 0, FnV = 0 [ 1786.013307] EA = 0, S1PTW = 0 [ 1786.013314] Data abort info: [ 1786.013322] ISV = 0, ISS = 0x00000045 [ 1786.013330] CM = 0, WnR = 1 [ 1786.013342] swapper pgtable: 4k pages, 39-bit VAs, pgdp = 000000008542a60e [ 1786.013350] [ffffffc00bd45000] pgd=0000000000000000, pud=0000000000000000 [ 1786.013368] Internal error: Oops: 96000045 [#1] PREEMPT SMP [ 1786.013609] Process swapper/0 (pid: 0, stack limit = 0x0000000084b153c6) [ 1786.013623] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.86 #137 [ 1786.013631] Hardware name: MediaTek krane sku176 board (DT) [ 1786.013643] pstate: 80000085 (Nzcv daIf -PAN -UAO) [ 1786.013662] pc : __memcpy+0x94/0x180 [ 1786.013678] lr : swiotlb_tbl_unmap_single+0x84/0x150 [ 1786.013686] sp : ffffff8008003c60 [ 1786.013694] x29: ffffff8008003c90 x28: ffffffae96411f80 [ 1786.013708] x27: ffffffae960d2018 x26: ffffff8019a4b9a8 [ 1786.013721] x25: 0000000000000000 x24: 0000000000000001 [ 1786.013734] x23: ffffffae96567000 x22: 00000000000051d4 [ 1786.013747] x21: 0000000000000000 x20: 00000000fe6e9000 [ 1786.013760] x19: 0000000000000004 x18: 0000000000000020 [ 1786.013773] x17: 0000000000000001 x16: 0000000000000000 [ 1786.013787] x15: 00000000ffffffff x14: 00000000000044c0 [ 1786.013800] x13: 0000000000365ba4 x12: 0000000000000000 [ 1786.013813] x11: 0000000000000001 x10: 00000037be6e9000 [ 1786.013826] x9 : ffffffc940000000 x8 : 000000000bd45000 [ 1786.013839] x7 : 0000000000000000 x6 : ffffffc00bd45000 [ 1786.013852] x5 : 0000000000000000 x4 : 0000000000000000 [ 1786.013865] x3 : 0000000000000c00 x2 : 0000000000000004 [ 1786.013878] x1 : fffffff7be6e9004 x0 : ffffffc00bd45000 [ 1786.013891] Call trace: [ 1786.013903] __memcpy+0x94/0x180 [ 1786.013914] unmap_single+0x6c/0x84 [ 1786.013925] swiotlb_unmap_sg_attrs+0x54/0x80 [ 1786.013938] __swiotlb_unmap_sg_attrs+0x8c/0xa4 [ 1786.013952] msdc_unprepare_data+0x6c/0x84 [ 1786.013963] msdc_request_done+0x58/0x84 [ 1786.013974] msdc_data_xfer_done+0x1a0/0x1c8 [ 1786.013985] msdc_irq+0x12c/0x17c [ 1786.013996] __handle_irq_event_percpu+0xe4/0x250 [ 1786.014006] handle_irq_event_percpu+0x28/0x68 [ 1786.014015] handle_irq_event+0x48/0x78 [ 1786.014026] handle_fasteoi_irq+0xd0/0x1a0 [ 1786.014039] __handle_domain_irq+0x84/0xc4 [ 1786.014050] gic_handle_irq+0x124/0x1a4 [ 1786.014059] el1_irq+0xb0/0x128 [ 1786.014072] cpuidle_enter_state+0x298/0x328 [ 1786.014082] cpuidle_enter+0x30/0x40 [ 1786.014094] do_idle+0x190/0x268 [ 1786.014104] cpu_startup_entry+0x24/0x28 [ 1786.014116] rest_init+0xd4/0xe0 [ 1786.014126] start_kernel+0x30c/0x38c [ 1786.014139] Code: f8408423 f80084c3 36100062 b8404423 (b80044c3) [ 1786.014150] ---[ end trace 3b02ddb698ea69ee ]--- [ 1786.015415] Kernel panic - not syncing: Fatal exception in interrupt [ 1786.015433] SMP: stopping secondary CPUs [ 1786.015447] Kernel Offset: 0x2e8d200000 from 0xffffff8008000000 [ 1786.015458] CPU features: 0x0,2188200c [ 1786.015466] Memory Limit: none For sdio chip, it need the memory which is kmalloc, if it is vmalloc from ath10k_mem_value_read, then it have a memory error. kzalloc of ath10k_sdio_hif_diag_read32 is the correct type, so add kzalloc in ath10k_sdio_hif_diag_read to replace the buffer which is vmalloc from ath10k_mem_value_read. This patch only effect sdio chip. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029. Signed-off-by:
Wen Gong <wgong@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Rodrigo Siqueira authored
[ Upstream commit a0e40018 ] Raven provides retimer feature support that requires i2c interaction in order to make it work well, all settings required for this configuration are loaded from the Atom bios which include the i2c address. If the retimer feature is not available, we should abort the attempt to set this feature, otherwise, it makes the following line return I2C_CHANNEL_OPERATION_NO_RESPONSE: i2c_success = i2c_write(pipe_ctx, slave_address, buffer, sizeof(buffer)); ... if (!i2c_success) ASSERT(i2c_success); This ends up causing problems with hotplugging HDMI displays on Raven, and causes retimer settings to warn like so: WARNING: CPU: 1 PID: 429 at drivers/gpu/drm/amd/amdgpu/../dal/dc/core/dc_link.c:1998 write_i2c_retimer_setting+0xc2/0x3c0 [amdgpu] Modules linked in: edac_mce_amd ccp kvm irqbypass binfmt_misc crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_codec_hdmi snd_hda_intel amdgpu(+) snd_hda_codec snd_hda_core snd_hwdep snd_pcm snd_seq_midi snd_seq_midi_event snd_rawmidi aesni_intel snd_seq amd_iommu_v2 gpu_sched aes_x86_64 crypto_simd cryptd glue_helper snd_seq_device ttm drm_kms_helper snd_timer eeepc_wmi wmi_bmof asus_wmi sparse_keymap drm mxm_wmi snd k10temp fb_sys_fops syscopyarea sysfillrect sysimgblt soundcore joydev input_leds mac_hid sch_fq_codel parport_pc ppdev lp parport ip_tables x_tables autofs4 igb i2c_algo_bit hid_generic usbhid i2c_piix4 dca ahci hid libahci video wmi gpio_amdpt gpio_generic CPU: 1 PID: 429 Comm: systemd-udevd Tainted: G W 5.2.0-rc1sept162019+ #1 Hardware name: System manufacturer System Product Name/ROG STRIX B450-F GAMING, BIOS 2605 08/06/2019 RIP: 0010:write_i2c_retimer_setting+0xc2/0x3c0 [amdgpu] Code: ff 0f b6 4d ce 44 0f b6 45 cf 44 0f b6 c8 45 89 cf 44 89 e2 48 c7 c6 f0 34 bc c0 bf 04 00 00 00 e8 63 b0 90 ff 45 84 ff 75 02 <0f> 0b 42 0f b6 04 73 8d 50 f6 80 fa 02 77 8c 3c 0a 0f 85 c8 00 00 RSP: 0018:ffffa99d02726fd0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffffa99d02727035 RCX: 0000000000000006 RDX: 0000000000000000 RSI: 0000000000000002 RDI: ffff976acc857440 RBP: ffffa99d02727018 R08: 0000000000000002 R09: 000000000002a600 R10: ffffe90610193680 R11: 00000000000005e3 R12: 000000000000005d R13: ffff976ac4b201b8 R14: 0000000000000001 R15: 0000000000000000 FS: 00007f14f99e1680(0000) GS:ffff976acc840000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fdf212843b8 CR3: 0000000408906000 CR4: 00000000003406e0 Call Trace: core_link_enable_stream+0x626/0x680 [amdgpu] dce110_apply_ctx_to_hw+0x414/0x4e0 [amdgpu] dc_commit_state+0x331/0x5e0 [amdgpu] ? drm_calc_timestamping_constants+0xf9/0x150 [drm] amdgpu_dm_atomic_commit_tail+0x395/0x1e00 [amdgpu] ? dm_plane_helper_prepare_fb+0x20c/0x280 [amdgpu] commit_tail+0x42/0x70 [drm_kms_helper] drm_atomic_helper_commit+0x10c/0x120 [drm_kms_helper] amdgpu_dm_atomic_commit+0x95/0xa0 [amdgpu] drm_atomic_commit+0x4a/0x50 [drm] restore_fbdev_mode_atomic+0x1c0/0x1e0 [drm_kms_helper] restore_fbdev_mode+0x4c/0x160 [drm_kms_helper] ? _cond_resched+0x19/0x40 drm_fb_helper_restore_fbdev_mode_unlocked+0x4e/0xa0 [drm_kms_helper] drm_fb_helper_set_par+0x2d/0x50 [drm_kms_helper] fbcon_init+0x471/0x630 visual_init+0xd5/0x130 do_bind_con_driver+0x20a/0x430 do_take_over_console+0x7d/0x1b0 do_fbcon_takeover+0x5c/0xb0 fbcon_event_notify+0x6cd/0x8a0 notifier_call_chain+0x4c/0x70 blocking_notifier_call_chain+0x43/0x60 fb_notifier_call_chain+0x1b/0x20 register_framebuffer+0x254/0x360 __drm_fb_helper_initial_config_and_unlock+0x2c5/0x510 [drm_kms_helper] drm_fb_helper_initial_config+0x35/0x40 [drm_kms_helper] amdgpu_fbdev_init+0xcd/0x100 [amdgpu] amdgpu_device_init+0x1156/0x1930 [amdgpu] amdgpu_driver_load_kms+0x8d/0x2e0 [amdgpu] drm_dev_register+0x12b/0x1c0 [drm] amdgpu_pci_probe+0xd3/0x160 [amdgpu] local_pci_probe+0x47/0xa0 pci_device_probe+0x142/0x1b0 really_probe+0xf5/0x3d0 driver_probe_device+0x11b/0x130 device_driver_attach+0x58/0x60 __driver_attach+0xa3/0x140 ? device_driver_attach+0x60/0x60 ? device_driver_attach+0x60/0x60 bus_for_each_dev+0x74/0xb0 ? kmem_cache_alloc_trace+0x1a3/0x1c0 driver_attach+0x1e/0x20 bus_add_driver+0x147/0x220 ? 0xffffffffc0cb9000 driver_register+0x60/0x100 ? 0xffffffffc0cb9000 __pci_register_driver+0x5a/0x60 amdgpu_init+0x74/0x83 [amdgpu] do_one_initcall+0x4a/0x1fa ? _cond_resched+0x19/0x40 ? kmem_cache_alloc_trace+0x3f/0x1c0 ? __vunmap+0x1cc/0x200 do_init_module+0x5f/0x227 load_module+0x2330/0x2b40 __do_sys_finit_module+0xfc/0x120 ? __do_sys_finit_module+0xfc/0x120 __x64_sys_finit_module+0x1a/0x20 do_syscall_64+0x5a/0x130 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7f14f9500839 Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 1f f6 2c 00 f7 d8 64 89 01 48 RSP: 002b:00007fff9bc4f5a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 RAX: ffffffffffffffda RBX: 000055afb5abce30 RCX: 00007f14f9500839 RDX: 0000000000000000 RSI: 000055afb5ace0f0 RDI: 0000000000000017 RBP: 000055afb5ace0f0 R08: 0000000000000000 R09: 000000000000000a R10: 0000000000000017 R11: 0000000000000246 R12: 0000000000000000 R13: 000055afb5aad800 R14: 0000000000020000 R15: 0000000000000000 ---[ end trace c286e96563966f08 ]--- This commit reworks the way that we handle i2c write for retimer in the way that we abort this configuration if the feature is not available in the device. For debug sake, we kept a simple log message in case the retimer is not available. Signed-off-by:
Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Reviewed-by:
Hersen Wu <hersenxs.wu@amd.com> Acked-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
John Clements authored
[ Upstream commit 1b3460a8 ] mitigates race condition on BACO reset between GPU bootcode and driver reload Reviewed-by:
Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by:
John Clements <john.clements@amd.com> Signed-off-by:
-
Kirill A. Shutemov authored
[ Upstream commit c3e5ea6e ] Jeff Moyer has reported that one of xfstests triggers a warning when run on DAX-enabled filesystem: WARNING: CPU: 76 PID: 51024 at mm/memory.c:2317 wp_page_copy+0xc40/0xd50 ... wp_page_copy+0x98c/0xd50 (unreliable) do_wp_page+0xd8/0xad0 __handle_mm_fault+0x748/0x1b90 handle_mm_fault+0x120/0x1f0 __do_page_fault+0x240/0xd70 do_page_fault+0x38/0xd0 handle_page_fault+0x10/0x30 The warning happens on failed __copy_from_user_inatomic() which tries to copy data into a CoW page. This happens because of race between MADV_DONTNEED and CoW page fault: CPU0 CPU1 handle_mm_fault() do_wp_page() wp_page_copy() do_wp_page() madvise(MADV_DONTNEED) zap_page_range() zap_pte_range() ptep_get_and_clear_full() <TLB flush> __copy_from_user_inatomic() sees empty PTE and fails WARN_ON_ONCE(1) clear_page() The solution is to re-try __copy_from_user_inatomic() under PTL after checking that PTE is matches the orig_pte. The second copy attempt can still fail, like due to non-readable PTE, but there's nothing reasonable we can do about, except clearing the CoW page. Reported-by:
Jeff Moyer <jmoyer@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Tested-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
John Garry authored
[ Upstream commit 3f5777fb ] The memory for global pointer is never freed during normal program execution, so let's do that in the main function exit as a good programming practice. A stray blank line is also removed. Reported-by:
Jiri Olsa <jolsa@redhat.com> Signed-off-by:
John Garry <john.garry@huawei.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: James Clark <james.clark@arm.com> Cc: Joakim Zhang <qiangqing.zhang@nxp.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will@kernel.org> Cc: linuxarm@huawei.com Link: http://lore.kernel.org/lkml/1583406486-154841-2-git-send-email-john.garry@huawei.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Qiujun Huang authored
[ Upstream commit dce8e237 ] KCSAN find inode->i_disksize could be accessed concurrently. BUG: KCSAN: data-race in ext4_mark_iloc_dirty / ext4_write_end write (marked) to 0xffff8b8932f40090 of 8 bytes by task 66792 on cpu 0: ext4_write_end+0x53f/0x5b0 ext4_da_write_end+0x237/0x510 generic_perform_write+0x1c4/0x2a0 ext4_buffered_write_iter+0x13a/0x210 ext4_file_write_iter+0xe2/0x9b0 new_sync_write+0x29c/0x3a0 __vfs_write+0x92/0xa0 vfs_write+0xfc/0x2a0 ksys_write+0xe8/0x140 __x64_sys_write+0x4c/0x60 do_syscall_64+0x8a/0x2a0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 read to 0xffff8b8932f40090 of 8 bytes by task 14414 on cpu 1: ext4_mark_iloc_dirty+0x716/0x1190 ext4_mark_inode_dirty+0xc9/0x360 ext4_convert_unwritten_extents+0x1bc/0x2a0 ext4_convert_unwritten_io_end_vec+0xc5/0x150 ext4_put_io_end+0x82/0x130 ext4_writepages+0xae7/0x16f0 do_writepages+0x64/0x120 __writeback_single_inode+0x7d/0x650 writeback_sb_inodes+0x3a4/0x860 __writeback_inodes_wb+0xc4/0x150 wb_writeback+0x43f/0x510 wb_workfn+0x3b2/0x8a0 process_one_work+0x39b/0x7e0 worker_thread+0x88/0x650 kthread+0x1d4/0x1f0 ret_from_fork+0x35/0x40 The plain read is outside of inode->i_data_sem critical section which results in a data race. Fix it by adding READ_ONCE(). Signed-off-by:
Qiujun Huang <hqjagain@gmail.com> Link: https://lore.kernel.org/r/1582556566-3909-1-git-send-email-hqjagain@gmail.comSigned-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Wen Yang authored
[ Upstream commit 4cbbc3a0 ] While unlikely the divisor in scale64_check_overflow() could be >= 32bit in scale64_check_overflow(). do_div() truncates the divisor to 32bit at least on 32bit platforms. Use div64_u64() instead to avoid the truncation to 32-bit. [ tglx: Massaged changelog ] Signed-off-by:
Wen Yang <wenyang@linux.alibaba.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20200120100523.45656-1-wenyang@linux.alibaba.comSigned-off-by:
-
Alain Michaud authored
[ Upstream commit 08bb4da9 ] Some controllers have been observed to send zero'd events under some conditions. This change guards against this condition as well as adding a trace to facilitate diagnosability of this condition. Signed-off-by:
Alain Michaud <alainm@chromium.org> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit a3ea410c ] Josef reported that his old-and-good Plextor ConvertX M402U video converter spews lots of WARNINGs on the recent kernels, and it turned out that the device uses a bulk endpoint for interrupt handling just like 2250 board. For fixing it, generalize the check with the proper verification of the endpoint instead of hard-coded board type check. Fixes: 7e5219d1 ("[media] go7007: Fix 2250 urb type") Reported-and-tested-by:
Josef Möllers <josef.moellers@suse.com> BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1162583 BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206427Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
-
John Garry authored
[ Upstream commit a6dd255b ] Some released ACPI FW for Huawei boards describes incorrect the port IO address range for child devices, in that it tells us the IO port max range is 0x3fff for each child device, which is not correct. The address range should be [e4:e8) or similar. With this incorrect upper range, the child device IO port resources overlap. As such, the kernel thinks that the LPC host serial device is a child of the IPMI device: root@(none)$ more /proc/ioports [...] 00ffc0e3-00ffffff : hisi-lpc-ipmi.0.auto 00ffc0e3-00ffc0e3 : ipmi_si 00ffc0e4-00ffc0e4 : ipmi_si 00ffc0e5-00ffc0e5 : ipmi_si 00ffc2f7-00ffffff : serial8250.1.auto 00ffc2f7-00ffc2fe : serial root@(none)$ They should both be siblings. Note that these are logical PIO addresses, which have a direct mapping from the FW IO port ranges. This shows up as a real issue when we enable CONFIG_KASAN and CONFIG_DEBUG_TEST_DRIVER_REMOVE - we see use-after-free warnings in the host removal path: ================================================================== BUG: KASAN: use-after-free in release_resource+0x38/0xc8 Read of size 8 at addr ffff0026accdbc38 by task swapper/0/1 CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.5.0-rc6-00001-g68e186e77b5c-dirty #1593 Hardware name: Huawei Taishan 2180 /D03, BIOS Hisilicon D03 IT20 Nemo 2.0 RC0 03/30/2018 Call trace: dump_backtrace+0x0/0x290 show_stack+0x14/0x20 dump_stack+0xf0/0x14c print_address_description.isra.9+0x6c/0x3b8 __kasan_report+0x12c/0x23c kasan_report+0xc/0x18 __asan_load8+0x94/0xb8 release_resource+0x38/0xc8 platform_device_del.part.10+0x80/0xe0 platform_device_unregister+0x20/0x38 hisi_lpc_acpi_remove_subdev+0x10/0x20 device_for_each_child+0xc8/0x128 hisi_lpc_acpi_remove+0x4c/0xa8 hisi_lpc_remove+0xbc/0xc0 platform_drv_remove+0x3c/0x68 really_probe+0x174/0x548 driver_probe_device+0x7c/0x148 device_driver_attach+0x94/0xa0 __driver_attach+0xa4/0x110 bus_for_each_dev+0xe8/0x158 driver_attach+0x30/0x40 bus_add_driver+0x234/0x2f0 driver_register+0xbc/0x1d0 __platform_driver_register+0x7c/0x88 hisi_lpc_driver_init+0x18/0x20 do_one_initcall+0xb4/0x258 kernel_init_freeable+0x248/0x2c0 kernel_init+0x10/0x118 ret_from_fork+0x10/0x1c ... The issue here is that the kernel created an incorrect parent-child resource dependency between two devices, and references the false parent node when deleting the second child device, when it had been deleted already. Fix up the child device resources from FW to create proper IO port resource relationships for broken FW. With this, the IO port layout looks more healthy: root@(none)$ more /proc/ioports [...] 00ffc0e3-00ffc0e7 : hisi-lpc-ipmi.0.auto 00ffc0e3-00ffc0e3 : ipmi_si 00ffc0e4-00ffc0e4 : ipmi_si 00ffc0e5-00ffc0e5 : ipmi_si 00ffc2f7-00ffc2ff : serial8250.1.auto 00ffc2f7-00ffc2fe : serial Signed-off-by:
Wei Xu <xuwei5@hisilicon.com> Signed-off-by:
-
Qian Cai authored
[ Upstream commit e00d996a ] Fields in "struct timer_rand_state" could be accessed concurrently. Lockless plain reads and writes result in data races. Fix them by adding pairs of READ|WRITE_ONCE(). The data races were reported by KCSAN, BUG: KCSAN: data-race in add_timer_randomness / add_timer_randomness write to 0xffff9f320a0a01d0 of 8 bytes by interrupt on cpu 22: add_timer_randomness+0x100/0x190 add_timer_randomness at drivers/char/random.c:1152 add_disk_randomness+0x85/0x280 scsi_end_request+0x43a/0x4a0 scsi_io_completion+0xb7/0x7e0 scsi_finish_command+0x1ed/0x2a0 scsi_softirq_done+0x1c9/0x1d0 blk_done_softirq+0x181/0x1d0 __do_softirq+0xd9/0x57c irq_exit+0xa2/0xc0 do_IRQ+0x8b/0x190 ret_from_intr+0x0/0x42 cpuidle_enter_state+0x15e/0x980 cpuidle_enter+0x69/0xc0 call_cpuidle+0x23/0x40 do_idle+0x248/0x280 cpu_startup_entry+0x1d/0x1f start_secondary+0x1b2/0x230 secondary_startup_64+0xb6/0xc0 no locks held by swapper/22/0. irq event stamp: 32871382 _raw_spin_unlock_irqrestore+0x53/0x60 _raw_spin_lock_irqsave+0x21/0x60 _local_bh_enable+0x21/0x30 irq_exit+0xa2/0xc0 read to 0xffff9f320a0a01d0 of 8 bytes by interrupt on cpu 2: add_timer_randomness+0xe8/0x190 add_disk_randomness+0x85/0x280 scsi_end_request+0x43a/0x4a0 scsi_io_completion+0xb7/0x7e0 scsi_finish_command+0x1ed/0x2a0 scsi_softirq_done+0x1c9/0x1d0 blk_done_softirq+0x181/0x1d0 __do_softirq+0xd9/0x57c irq_exit+0xa2/0xc0 do_IRQ+0x8b/0x190 ret_from_intr+0x0/0x42 cpuidle_enter_state+0x15e/0x980 cpuidle_enter+0x69/0xc0 call_cpuidle+0x23/0x40 do_idle+0x248/0x280 cpu_startup_entry+0x1d/0x1f start_secondary+0x1b2/0x230 secondary_startup_64+0xb6/0xc0 no locks held by swapper/2/0. irq event stamp: 37846304 _raw_spin_unlock_irqrestore+0x53/0x60 _raw_spin_lock_irqsave+0x21/0x60 _local_bh_enable+0x21/0x30 irq_exit+0xa2/0xc0 Reported by Kernel Concurrency Sanitizer on: Hardware name: HP ProLiant BL660c Gen9, BIOS I38 10/17/2018 Link: https://lore.kernel.org/r/1582648024-13111-1-git-send-email-cai@lca.pwSigned-off-by:
Qian Cai <cai@lca.pw> Signed-off-by:
-
James Morse authored
[ Upstream commit 54f529a6 ] SDEI has private events that need registering and enabling on each CPU. CPUs can come and go while we are trying to do this. SDEI tries to avoid these problems by setting the reregister flag before the register call, so any CPUs that come online register the event too. Sticking plaster like this doesn't work, as if the register call fails, a CPU that subsequently comes online will register the event before reregister is cleared. Take cpus_read_lock() around the register and enable calls. We don't want surprise CPUs to do the wrong thing if they race with these calls failing. Signed-off-by:
James Morse <james.morse@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Aric Cyr authored
[ Upstream commit 6a6c4a4d ] [Why] Since the i2c payload allocation can fail need to check return codes [How] Clean up i2c payload allocations and check for errors Signed-off-by:
Aric Cyr <aric.cyr@amd.com> Reviewed-by:
Joshua Aberback <Joshua.Aberback@amd.com> Acked-by:
Harry Wentland <harry.wentland@amd.com> Signed-off-by:
-
Dmitry Osipenko authored
[ Upstream commit 8e84172e ] It's incorrect to check the channel's "busy" state without taking a lock. That shouldn't cause any real troubles, nevertheless it's always better not to have any race conditions in the code. Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Acked-by:
Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20200209163356.6439-5-digetx@gmail.comSigned-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Amelie Delaunay authored
[ Upstream commit d80cbef3 ] To avoid race with vchan_complete, use the race free way to terminate running transfer. Move vdesc->node list_del in stm32_dma_start_transfer instead of in stm32_mdma_chan_complete to avoid another race in vchan_dma_desc_free_list. Signed-off-by:
Amelie Delaunay <amelie.delaunay@st.com> Link: https://lore.kernel.org/r/20200129153628.29329-9-amelie.delaunay@st.comSigned-off-by:
-
Thomas Gleixner authored
[ Upstream commit 8a37963c ] If an element is freed via RCU then recursion into BPF instrumentation functions is not a concern. The element is already detached from the map and the RCU callback does not hold any locks on which a kprobe, perf event or tracepoint attached BPF program could deadlock. Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20200224145643.259118710@linutronix.deSigned-off-by:
-
Dave Hansen authored
[ Upstream commit 16171bff ] Alex Shi reported the pkey macros above arch_set_user_pkey_access() to be unused. They are unused, and even refer to a nonexistent CONFIG option. But, they might have served a good use, which was to ensure that the code does not try to set values that would not fit in the PKRU register. As it stands, a too-large 'pkey' value would be likely to silently overflow the u32 new_pkru_bits. Add a check to look for overflows. Also add a comment to remind any future developer to closely examine the types used to store pkey values if arch_max_pkey() ever changes. This boots and passes the x86 pkey selftests. Reported-by:
Alex Shi <alex.shi@linux.alibaba.com> Signed-off-by:
Dave Hansen <dave.hansen@intel.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20200122165346.AD4DA150@viggo.jf.intel.comSigned-off-by:
-
Dan Carpenter authored
[ Upstream commit ef0ed05d ] There was supposed to be a "ret = " assignment here, otherwise the error handling on the next line won't work. Fixes: 64b5a49d ("[media] media: imx: Add Capture Device Interface") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by:
-
Amelie Delaunay authored
[ Upstream commit dfc70881 ] To avoid race with vchan_complete, use the race free way to terminate running transfer. Move vdesc->node list_del in stm32_mdma_start_transfer instead of in stm32_mdma_xfer_end to avoid another race in vchan_dma_desc_free_list. Signed-off-by:
-
Paolo Bonzini authored
[ Upstream commit 147f1a1f ] The "u" field in the event has three states, -1/0/1. Using u8 however means that comparison with -1 will always fail, so change to signed char. Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Bart Van Assche authored
[ Upstream commit fb3063d3 ] From the comment above the definition of the roundup_pow_of_two() macro: The result is undefined when n == 0. Hence only pass positive values to roundup_pow_of_two(). This patch fixes the following UBSAN complaint: UBSAN: Undefined behaviour in ./include/linux/log2.h:57:13 shift exponent 64 is too large for 64-bit type 'long unsigned int' Call Trace: dump_stack+0xa5/0xe6 ubsan_epilogue+0x9/0x26 __ubsan_handle_shift_out_of_bounds.cold+0x4c/0xf9 rxe_qp_from_attr.cold+0x37/0x5d [rdma_rxe] rxe_modify_qp+0x59/0x70 [rdma_rxe] _ib_modify_qp+0x5aa/0x7c0 [ib_core] ib_modify_qp+0x3b/0x50 [ib_core] cma_modify_qp_rtr+0x234/0x260 [rdma_cm] __rdma_accept+0x1a7/0x650 [rdma_cm] nvmet_rdma_cm_handler+0x1286/0x14cd [nvmet_rdma] cma_cm_event_handler+0x6b/0x330 [rdma_cm] cma_ib_req_handler+0xe60/0x22d0 [rdma_cm] cm_process_work+0x30/0x140 [ib_cm] cm_req_handler+0x11f4/0x1cd0 [ib_cm] cm_work_handler+0xb8/0x344e [ib_cm] process_one_work+0x569/0xb60 worker_thread+0x7a/0x5d0 kthread+0x1e6/0x210 ret_from_fork+0x24/0x30 Link: https://lore.kernel.org/r/20200217205714.26937-1-bvanassche@acm.org Fixes: 8700e3e7 ("Soft RoCE driver") Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Reviewed-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Thomas Richter authored
[ Upstream commit 2bbc8353 ] This test places a kprobe to function getname_flags() in the kernel which has the following prototype: struct filename *getname_flags(const char __user *filename, int flags, int *empty) The 'filename' argument points to a filename located in user space memory. Looking at commit 88903c46 ("tracing/probe: Add ustring type for user-space string") the kprobe should indicate that user space memory is accessed. Output before: [root@m35lp76 perf]# ./perf test 66 67 66: Use vfs_getname probe to get syscall args filenames : FAILED! 67: Check open filename arg using perf trace + vfs_getname: FAILED! [root@m35lp76 perf]# Output after: [root@m35lp76 perf]# ./perf test 66 67 66: Use vfs_getname probe to get syscall args filenames : Ok 67: Check open filename arg using perf trace + vfs_getname: Ok [root@m35lp76 perf]# Comments from Masami Hiramatsu: This bug doesn't happen on x86 or other archs on which user address space and kernel address space is the same. On some arches (ppc64 in this case?) user address space is partially or completely the same as kernel address space. (Yes, they switch the world when running into the kernel) In this case, we need to use different data access functions for each space. That is why I introduced the "ustring" type for kprobe events. As far as I can see, Thomas's patch is sane. Thomas, could you show us your result on your test environment? Comments from Thomas Richter: Test results for s/390 included above. Signed-off-by:
Thomas Richter <tmricht@linux.ibm.com> Acked-by:
Masami Hiramatsu <mhiramat@kernel.org> Tested-by:
-
Takashi Iwai authored
[ Upstream commit e9a0ef0b ] Some USB-audio descriptors provide a bogus volume range (e.g. volume min and max are identical), which confuses user-space. This patch makes the driver skipping such a control element. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206221 Link: https://lore.kernel.org/r/20200214144928.23628-1-tiwai@suse.deSigned-off-by:
-
Felix Fietkau authored
[ Upstream commit 9379df2f ] During the cleanup of the aggregation session, a rx handler (or release timer) on another CPU might still hold a pointer to the reorder buffer and could attempt to release some packets. Clearing pointers during cleanup avoids a theoretical use-after-free bug here. Signed-off-by:
Felix Fietkau <nbd@nbd.name> Signed-off-by:
-
Ayush Sawal authored
[ Upstream commit 9195189e ] The libkcapi test which causes kernel panic is aead asynchronous vmsplice multiple test. ./bin/kcapi -v -d 4 -x 10 -c "ccm(aes)" -q 4edb58e8d5eb6bc711c43a6f3693daebde2e5524f1b55297abb29f003236e43d -t a7877c99 -n 674742abd0f5ba -k 2861fd0253705d7875c95ba8a53171b4 -a fb7bc304a3909e66e2e0c5ef952712dd884ce3e7324171369f2c5db1adc48c7d This patch avoids dma_mapping of a zero length sg which causes the panic, by using sg_nents_for_len which maps only upto a specific length Signed-off-by:
Ayush Sawal <ayush.sawal@chelsio.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Dinh Nguyen authored
[ Upstream commit cc26ed7b ] do_div() macro to perform u64 division and guards against overflow if the result is too large for the unsigned long return type. Signed-off-by:
Dinh Nguyen <dinguyen@kernel.org> Link: https://lkml.kernel.org/r/20200114160726.19771-1-dinguyen@kernel.orgSigned-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Wen Yang authored
[ Upstream commit 47340e46 ] The call to of_find_matching_node returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c:212:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 209, but without a corresponding object release within this function. drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c:237:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 209, but without a corresponding object release within this function. Signed-off-by:
Wen Yang <wen.yang99@zte.com.cn> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
Mukesh Ojha <mojha@codeaurora.org> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Sebastian Reichel <sebastian.reichel@collabora.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: dri-devel@lists.freedesktop.org Cc: linux-kernel@vger.kernel.org Cc: Markus Elfring <Markus.Elfring@web.de> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Link: https://patchwork.freedesktop.org/patch/msgid/1554692313-28882-2-git-send-email-wen.yang99@zte.com.cnSigned-off-by:
-
James Smart authored
[ Upstream commit 4cb9e1dd ] Coverity reported a memory corruption error for the fdmi attributes routines: CID 15768 [Memory Corruption] Out-of-bounds access on FDMI Sloppy coding of the fmdi structures. In both the lpfc_fdmi_attr_def and lpfc_fdmi_reg_port_list structures, a field was placed at the start of payload that may have variable content. The field was given an arbitrary type (uint32_t). The code then uses the field name to derive an address, which it used in things such as memset and memcpy. The memset sizes or memcpy lengths were larger than the arbitrary type, thus coverity reported an error. Fix by replacing the arbitrary fields with the real field structures describing the payload. Link: https://lore.kernel.org/r/20200128002312.16346-8-jsmart2021@gmail.comSigned-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Signed-off-by:
-
James Smart authored
[ Upstream commit 39c4f1a9 ] The driver is occasionally seeing the following SLI Port error, requiring reset and reinit: Port Status Event: ... error 1=0x52004a01, error 2=0x218 The failure means an RQ timeout. That is, the adapter had received asynchronous receive frames, ran out of buffer slots to place the frames, and the driver did not replenish the buffer slots before a timeout occurred. The driver should not be so slow in replenishing buffers that a timeout can occur. When the driver received all the frames of a sequence, it allocates an IOCB to put the frames in. In a situation where there was no IOCB available for the frame of a sequence, the RQ buffer corresponding to the first frame of the sequence was not returned to the FW. Eventually, with enough traffic encountering the situation, the timeout occurred. Fix by releasing the buffer back to firmware whenever there is no IOCB for the first frame. [mkp: typo] Link: https://lore.kernel.org/r/20200128002312.16346-2-jsmart2021@gmail.comSigned-off-by:
-
Vasily Averin authored
[ Upstream commit 8d269a8e ] If seq_file .next function does not change position index, read after some lseek can generate unexpected output. $ dd if=/sys/fs/selinux/avc/cache_stats # usual output lookups hits misses allocations reclaims frees 817223 810034 7189 7189 6992 7037 1934894 1926896 7998 7998 7632 7683 1322812 1317176 5636 5636 5456 5507 1560571 1551548 9023 9023 9056 9115 0+1 records in 0+1 records out 189 bytes copied, 5,1564e-05 s, 3,7 MB/s $# read after lseek to midle of last line $ dd if=/sys/fs/selinux/avc/cache_stats bs=180 skip=1 dd: /sys/fs/selinux/avc/cache_stats: cannot skip to specified offset 056 9115 <<<< end of last line 1560571 1551548 9023 9023 9056 9115 <<< whole last line once again 0+1 records in 0+1 records out 45 bytes copied, 8,7221e-05 s, 516 kB/s $# read after lseek beyond end of of file $ dd if=/sys/fs/selinux/avc/cache_stats bs=1000 skip=1 dd: /sys/fs/selinux/avc/cache_stats: cannot skip to specified offset 1560571 1551548 9023 9023 9056 9115 <<<< generates whole last line 0+1 records in 0+1 records out 36 bytes copied, 9,0934e-05 s, 396 kB/s https://bugzilla.kernel.org/show_bug.cgi?id=206283Signed-off-by:
Vasily Averin <vvs@virtuozzo.com> Acked-by:
Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Steve Grubb authored
[ Upstream commit 70b3eeed ] Common Criteria calls out for any action that modifies the audit trail to be recorded. That usually is interpreted to mean insertion or removal of rules. It is not required to log modification of the inode information since the watch is still in effect. Additionally, if the rule is a never rule and the underlying file is one they do not want events for, they get an event for this bookkeeping update against their wishes. Since no device/inode info is logged at insertion and no device/inode information is logged on update, there is nothing meaningful being communicated to the admin by the CONFIG_CHANGE updated_rules event. One can assume that the rule was not "modified" because it is still watching the intended target. If the device or inode cannot be resolved, then audit_panic is called which is sufficient. The correct resolution is to drop logging config_update events since the watch is still in effect but just on another unknown inode. Signed-off-by:
Steve Grubb <sgrubb@redhat.com> Signed-off-by:
-
Qian Cai authored
[ Upstream commit 86b18aaa ] sk_buff.qlen can be accessed concurrently as noticed by KCSAN, BUG: KCSAN: data-race in __skb_try_recv_from_queue / unix_dgram_sendmsg read to 0xffff8a1b1d8a81c0 of 4 bytes by task 5371 on cpu 96: unix_dgram_sendmsg+0x9a9/0xb70 include/linux/skbuff.h:1821 net/unix/af_unix.c:1761 ____sys_sendmsg+0x33e/0x370 ___sys_sendmsg+0xa6/0xf0 __sys_sendmsg+0x69/0xf0 __x64_sys_sendmsg+0x51/0x70 do_syscall_64+0x91/0xb47 entry_SYSCALL_64_after_hwframe+0x49/0xbe write to 0xffff8a1b1d8a81c0 of 4 bytes by task 1 on cpu 99: __skb_try_recv_from_queue+0x327/0x410 include/linux/skbuff.h:2029 __skb_try_recv_datagram+0xbe/0x220 unix_dgram_recvmsg+0xee/0x850 ____sys_recvmsg+0x1fb/0x210 ___sys_recvmsg+0xa2/0xf0 __sys_recvmsg+0x66/0xf0 __x64_sys_recvmsg+0x51/0x70 do_syscall_64+0x91/0xb47 entry_SYSCALL_64_after_hwframe+0x49/0xbe Since only the read is operating as lockless, it could introduce a logic bug in unix_recvq_full() due to the load tearing. Fix it by adding a lockless variant of skb_queue_len() and unix_recvq_full() where READ_ONCE() is on the read while WRITE_ONCE() is on the write similar to the commit d7d16a89 ("net: add skb_queue_empty_lockless()"). Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Mohan Kumar authored
[ Upstream commit 6d011d50 ] RIRB interrupt status getting cleared after the write pointer is read causes a race condition, where last response(s) into RIRB may remain unserviced by IRQ, eventually causing azx_rirb_get_response to fall back to polling mode. Clearing the RIRB interrupt status ahead of write pointer access ensures that this condition is avoided. Signed-off-by:
Mohan Kumar <mkumard@nvidia.com> Signed-off-by:
Viswanath L <viswanathl@nvidia.com> Link: https://lore.kernel.org/r/1580983853-351-1-git-send-email-viswanathl@nvidia.comSigned-off-by:
-
Zhuang Yanying authored
[ Upstream commit 7df003c8 ] We are testing Virtual Machine with KSM on v5.4-rc2 kernel, and found the zero_page refcount overflow. The cause of refcount overflow is increased in try_async_pf (get_user_page) without being decreased in mmu_set_spte() while handling ept violation. In kvm_release_pfn_clean(), only unreserved page will call put_page. However, zero page is reserved. So, as well as creating and destroy vm, the refcount of zero page will continue to increase until it overflows. step1: echo 10000 > /sys/kernel/pages_to_scan/pages_to_scan echo 1 > /sys/kernel/pages_to_scan/run echo 1 > /sys/kernel/pages_to_scan/use_zero_pages step2: just create several normal qemu kvm vms. And destroy it after 10s. Repeat this action all the time. After a long period of time, all domains hang because of the refcount of zero page overflow. Qemu print error log as follow: … error: kvm run failed Bad address EAX=00006cdc EBX=00000008 ECX=80202001 EDX=078bfbfd ESI=ffffffff EDI=00000000 EBP=00000008 ESP=00006cc4 EIP=000efd75 EFL=00010002 [-------] CPL=0 II=0 A20=1 SMM=0 HLT=0 ES =0010 00000000 ffffffff 00c09300 DPL=0 DS [-WA] CS =0008 00000000 ffffffff 00c09b00 DPL=0 CS32 [-RA] SS =0010 00000000 ffffffff 00c09300 DPL=0 DS [-WA] DS =0010 00000000 ffffffff 00c09300 DPL=0 DS [-WA] FS =0010 00000000 ffffffff 00c09300 DPL=0 DS [-WA] GS =0010 00000000 ffffffff 00c09300 DPL=0 DS [-WA] LDT=0000 00000000 0000ffff 00008200 DPL=0 LDT TR =0000 00000000 0000ffff 00008b00 DPL=0 TSS32-busy GDT= 000f7070 00000037 IDT= 000f70ae 00000000 CR0=00000011 CR2=00000000 CR3=00000000 CR4=00000000 DR0=0000000000000000 DR1=0000000000000000 DR2=0000000000000000 DR3=0000000000000000 DR6=00000000ffff0ff0 DR7=0000000000000400 EFER=0000000000000000 Code=00 01 00 00 00 e9 e8 00 00 00 c7 05 4c 55 0f 00 01 00 00 00 <8b> 35 00 00 01 00 8b 3d 04 00 01 00 b8 d8 d3 00 00 c1 e0 08 0c ea a3 00 00 01 00 c7 05 04 … Meanwhile, a kernel warning is departed. [40914.836375] WARNING: CPU: 3 PID: 82067 at ./include/linux/mm.h:987 try_get_page+0x1f/0x30 [40914.836412] CPU: 3 PID: 82067 Comm: CPU 0/KVM Kdump: loaded Tainted: G OE 5.2.0-rc2 #5 [40914.836415] RIP: 0010:try_get_page+0x1f/0x30 [40914.836417] Code: 40 00 c3 0f 1f 84 00 00 00 00 00 48 8b 47 08 a8 01 75 11 8b 47 34 85 c0 7e 10 f0 ff 47 34 b8 01 00 00 00 c3 48 8d 78 ff eb e9 <0f> 0b 31 c0 c3 66 90 66 2e 0f 1f 84 00 0 0 00 00 00 48 8b 47 08 a8 [40914.836418] RSP: 0018:ffffb4144e523988 EFLAGS: 00010286 [40914.836419] RAX: 0000000080000000 RBX: 0000000000000326 RCX: 0000000000000000 [40914.836420] RDX: 0000000000000000 RSI: 00004ffdeba10000 RDI: ffffdf07093f6440 [40914.836421] RBP: ffffdf07093f6440 R08: 800000424fd91225 R09: 0000000000000000 [40914.836421] R10: ffff9eb41bfeebb8 R11: 0000000000000000 R12: ffffdf06bbd1e8a8 [40914.836422] R13: 0000000000000080 R14: 800000424fd91225 R15: ffffdf07093f6440 [40914.836423] FS: 00007fb60ffff700(0000) GS:ffff9eb4802c0000(0000) knlGS:0000000000000000 [40914.836425] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [40914.836426] CR2: 0000000000000000 CR3: 0000002f220e6002 CR4: 00000000003626e0 [40914.836427] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [40914.836427] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [40914.836428] Call Trace: [40914.836433] follow_page_pte+0x302/0x47b [40914.836437] __get_user_pages+0xf1/0x7d0 [40914.836441] ? irq_work_queue+0x9/0x70 [40914.836443] get_user_pages_unlocked+0x13f/0x1e0 [40914.836469] __gfn_to_pfn_memslot+0x10e/0x400 [kvm] [40914.836486] try_async_pf+0x87/0x240 [kvm] [40914.836503] tdp_page_fault+0x139/0x270 [kvm] [40914.836523] kvm_mmu_page_fault+0x76/0x5e0 [kvm] [40914.836588] vcpu_enter_guest+0xb45/0x1570 [kvm] [40914.836632] kvm_arch_vcpu_ioctl_run+0x35d/0x580 [kvm] [40914.836645] kvm_vcpu_ioctl+0x26e/0x5d0 [kvm] [40914.836650] do_vfs_ioctl+0xa9/0x620 [40914.836653] ksys_ioctl+0x60/0x90 [40914.836654] __x64_sys_ioctl+0x16/0x20 [40914.836658] do_syscall_64+0x5b/0x180 [40914.836664] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [40914.836666] RIP: 0033:0x7fb61cb6bfc7 Signed-off-by:
LinFeng <linfeng23@huawei.com> Signed-off-by:
Zhuang Yanying <ann.zhuangyanying@huawei.com> Signed-off-by:
-
Hillf Danton authored
[ Upstream commit 2a154903 ] Prefetch channel before killing sock in order to fix UAF like BUG: KASAN: use-after-free in l2cap_sock_release+0x24c/0x290 net/bluetooth/l2cap_sock.c:1212 Read of size 8 at addr ffff8880944904a0 by task syz-fuzzer/9751 Reported-by: syzbot+c3c5bdea7863886115dc@syzkaller.appspotmail.com Fixes: 6c08fc89 ("Bluetooth: Fix refcount use-after-free issue") Cc: Manish Mandlik <mmandlik@google.com> Signed-off-by:
Hillf Danton <hdanton@sina.com> Signed-off-by:
-
Steven Price authored
[ Upstream commit c02a9875 ] If walk_pte_range() is called with a 'end' argument that is beyond the last page of memory (e.g. ~0UL) then the comparison between 'addr' and 'end' will always fail and the loop will be infinite. Instead change the comparison to >= while accounting for overflow. Link: http://lkml.kernel.org/r/20191218162402.45610-15-steven.price@arm.comSigned-off-by:
Steven Price <steven.price@arm.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Alexandre Ghiti <alex@ghiti.fr> Cc: Andy Lutomirski <luto@kernel.org> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Hogan <jhogan@kernel.org> Cc: James Morse <james.morse@arm.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: "Liang, Kan" <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Paul Burton <paul.burton@mips.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Will Deacon <will@kernel.org> Cc: Zong Li <zong.li@sifive.com> Signed-off-by:
-
Vasily Averin authored
[ Upstream commit 10c8d69f ] If seq_file .next fuction does not change position index, read after some lseek can generate unexpected output. In Aug 2018 NeilBrown noticed commit 1f4aace6 ("fs/seq_file.c: simplify seq_file iteration code and interface") "Some ->next functions do not increment *pos when they return NULL... Note that such ->next functions are buggy and should be fixed. A simple demonstration is dd if=/proc/swaps bs=1000 skip=1 Choose any block size larger than the size of /proc/swaps. This will always show the whole last line of /proc/swaps" Described problem is still actual. If you make lseek into middle of last output line following read will output end of last line and whole last line once again. $ dd if=/proc/swaps bs=1 # usual output Filename Type Size Used Priority /dev/dm-0 partition 4194812 97536 -2 104+0 records in 104+0 records out 104 bytes copied $ dd if=/proc/swaps bs=40 skip=1 # last line was generated twice dd: /proc/swaps: cannot skip to specified offset v/dm-0 partition 4194812 97536 -2 /dev/dm-0 partition 4194812 97536 -2 3+1 records in 3+1 records out 131 bytes copied https://bugzilla.kernel.org/show_bug.cgi?id=206283 Link: http://lkml.kernel.org/r/bd8cfd7b-ac95-9b91-f9e7-e8438bd5047d@virtuozzo.comSigned-off-by:
-
