On STM32MP15, OTP area may be read/written by using BSEC (boot, security
and OTP control). BSEC registers set is composed of various regions, among
which control registers and OTP shadow registers.
Secure monitor calls are involved in this process to allow (or deny)
access to the full range of OTP data.
This adds support for reading and writing OTP data using SMC services.
Data content can be aligned on 16-bits or 8-bits. Then take care of it,
since BSEC data is 32-bits wide.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a read only nvmem driver for STM32 factory-programmed memory area
(on-chip non-volatile storage).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add documentation for STMicroelectronics STM32 Factory-programmed
read only memory area.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The device tree binding already lists compatible strings for these two
SoCs. They don't have the defect as seen on the H3, and the size and
register layout is the same as the A64. Furthermore, the driver does
not include nvmem cell definitions.

Add support for these two compatible strings, re-using the config for
the A64.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Originally the SID e-fuses were thought to be in big-endian format.
Later sources show that they are in fact native or little-endian.
The most compelling evidence is the thermal sensor calibration data,
which is a set of one to three 16-bit values. In native-endian they
are in 16-bit cells with increasing offsets, whereas with big-endian
they are in the wrong order, and a gap with no data will show if there
are one or three cells.

Switch to a native endian representation for the nvmem device. For the
H3, the register read-out method was already returning data in native
endian. This only affects the other SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The sunxi_sid driver currently uses a statically allocated nvmem_config
structure that is updated at probe time. This is sub-optimal as it
limits the driver to one instance, and also takes up space even if the
device is not present.

Modify the driver to allocate the nvmem_config structure at probe time,
plugging in the desired parameters along the way.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SID cells are 32-bit aligned, and a multiple of 32 bits in length. The
only outlier is the thermal sensor calibration data, which is 16 bits
per sensor. However a whole 64 bits is allocated for this purpose, so
we could consider it conforming to the rule above.

Also, the register read-out method assumes native endian, unlike the
direct MMIO method, which assumes big endian. Thus no endian conversion
is involved.

Under these assumptions, the register read-out method can be slightly
optimized. Instead of reading one word then discarding 3 bytes, read
the whole word directly into the buffer. However, for reads under 4
bytes or trailing bytes, we still use a scratch buffer to extract the
requested bytes.

We could go one step further if .word_size was 4, but changing that
would affect the sysfs interface's behavior.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since the reg_read callbacks already support arbitrary, but 4-byte
aligned. offsets and lengths into the SID, there is no need for another
for loop just to use it to read 1 byte at a time.

Read out the whole SID block in one go.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The i.MX OCOTP controller is used in numerous Freescale/NXP
SoCs from the MXC family, so the strict dependency on the
i.MX6 SoC is too narrow. Broaden it to cover all the MXC
familiy members.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The i.MX8MQ uses the same OCOTP block as the i.MX7D, but with
fourfold increase in fuse banks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

This patch fixes the following warning:

drivers/parport/ieee1284.c: In function ‘parport_read’:
drivers/parport/ieee1284.c:722:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (parport_negotiate (port, IEEE1284_MODE_NIBBLE)) {
      ^
drivers/parport/ieee1284.c:726:2: note: here
  case IEEE1284_MODE_NIBBLE:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When we have success in 'Channel Access Write' but reading back latch
states fails, a write is retried without doing a proper slave reset.
This leads to protocol errors as the slave treats the next 'Channel
Access Write' as the continuation of previous command.

This commit is fixing this by making sure if the retry loop re-runs, a
reset is performed, whatever the failure (CONFIRM_BYTE or the read
back).

The loop was quite due for a cleanup and this change mandated it. By
isolating the CONFIG_W1_SLAVE_DS2408_READBACK case into it's own
function, we vastly reduce the visual and branching(runtime and
compile-time) noise.
Reported-by: Mariusz Bialonczyk <manio@skyboo.net>
Tested-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Georgi writes:

interconnect: for 5.2

Here are some tiny patches for the 5.2-rc1 merge window:

- Add linux-pm@ as a mailing list for the interconnect API.
- Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>

* tag 'icc-5.2-rc1' of https://git.linaro.org/people/georgi.djakov/linux:
  interconnect: convert to DEFINE_SHOW_ATTRIBUTE
  MAINTAINERS: Add mailing list for the interconnect API

Expose mei device state to user-space through sysfs.
This gives indication to applications that driver is in transition,
usefully mostly to detect link reset state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The mei/hdcp module have its own Makefile
so naturally it should have associated Kconfig
in the same directory.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The ASPEED AST2400, and AST2500 in some configurations include a
PCI-to-AHB MMIO bridge.  This bridge allows a server to read and write
in the BMC's physical address space.  This feature is especially useful
when using this bridge to send large files to the BMC.

The host may use this to send down a firmware image by staging data at a
specific memory address, and in a coordinated effort with the BMC's
software stack and kernel, transmit the bytes.

This driver enables the BMC to unlock the PCI bridge on demand, and
configure it via ioctl to allow the host to write bytes to an agreed
upon location.  In the primary use-case, the region to use is known
apriori on the BMC, and the host requests this information.  Once this
request is received, the BMC's software stack will enable the bridge and
the region and then using some software flow control (possibly via IPMI
packets), copy the bytes down.  Once the process is complete, the BMC
will disable the bridge and unset any region involved.

The default behavior of this bridge when present is: enabled and all
regions marked read-write.  This driver will fix the regions to be
read-only and then disable the bridge entirely.

The memory regions protected are:
 * BMC flash MMIO window
 * System flash MMIO windows
 * SOC IO (peripheral MMIO)
 * DRAM

The DRAM region itself is all of DRAM and cannot be further specified.
Once the PCI bridge is enabled, the host can read all of DRAM, and if
the DRAM section is write-enabled, then it can write to all of it.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Document the ast2400, ast2500 PCI-to-AHB bridge control driver bindings.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the fixes, and this resolves a merge error in the fastrpc
driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull NFS client bugfix from Trond Myklebust:
 "Fix a regression in which an RPC call can be tagged with an error
  despite the transmission being successful"

* tag 'nfs-for-5.1-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: Ignore queue transmission errors on successful transmission

Pull SCSI fixes from James Bottomley:
 "Three minor fixes: two obvious ones in drivers and a fix to the SG_IO
  path to correctly return status on error"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: aic7xxx: fix EISA support
  Revert "scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO"
  scsi: core: set result when the command cannot be dispatched

Pull block fixes from Jens Axboe:
 "A set of small fixes that should go into this series. This contains:

   - Removal of unused queue member (Hou)

   - Overflow bvec fix (Ming)

   - Various little io_uring tweaks (me)
       - kthread parking
       - Only call cpu_possible() for verified CPU
       - Drop unused 'file' argument to io_file_put()
       - io_uring_enter vs io_uring_register deadlock fix
       - CQ overflow fix

   - BFQ internal depth update fix (me)"

* tag 'for-linus-20190420' of git://git.kernel.dk/linux-block:
  block: make sure that bvec length can't be overflow
  block: kill all_q_node in request_queue
  io_uring: fix CQ overflow condition
  io_uring: fix possible deadlock between io_uring_{enter,register}
  io_uring: drop io_file_put() 'file' argument
  bfq: update internal depth state when queue depth changes
  io_uring: only test SQPOLL cpu after we've verified it
  io_uring: park SQPOLL thread if it's percpu

Pill i3c fixes from Boris Brezillon:

 - fix the random PID check

 - fix the disable controller logic in the designware driver

 - fix I3C entry in MAINTAINERS

* tag 'i3c/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
  MAINTAINERS: Fix the I3C entry
  i3c: dw: Fix dw_i3c_master_disable controller by using correct mask
  i3c: Fix the verification of random PID

Pull sound fixes from Takashi Iwai:
 "Two core fixes for long-standing bugs for the races at concurrent
  device creation and deletion that were (unsurprisingly) spotted by
  syzkaller with usb-fuzzer.

  The rest are usual small HD-audio fixes"

* tag 'sound-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - add two more pin configuration sets to quirk table
  ALSA: core: Fix card races between register and disconnect
  ALSA: info: Fix racy addition/deletion of nodes
  ALSA: hda: Initialize power_state field properly

Pull timer fixes from Ingo Molnar:
 "Misc clocksource driver fixes, and a sched-clock wrapping fix"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timers/sched_clock: Prevent generic sched_clock wrap caused by tick_freeze()
  clocksource/drivers/timer-ti-dm: Remove omap_dm_timer_set_load_start
  clocksource/drivers/oxnas: Fix OX820 compatible
  clocksource/drivers/arm_arch_timer: Remove unneeded pr_fmt macro
  clocksource/drivers/npcm: select TIMER_OF

Pull perf fixes from Ingo Molnar:
 "Misc fixes:
   - various tooling fixes
   - kretprobe fixes
   - kprobes annotation fixes
   - kprobes error checking fix
   - fix the default events for AMD Family 17h CPUs
   - PEBS fix
   - AUX record fix
   - address filtering fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kprobes: Avoid kretprobe recursion bug
  kprobes: Mark ftrace mcount handler functions nokprobe
  x86/kprobes: Verify stack frame on kretprobe
  perf/x86/amd: Add event map for AMD Family 17h
  perf bpf: Return NULL when RB tree lookup fails in perf_env__find_btf()
  perf tools: Fix map reference counting
  perf evlist: Fix side band thread draining
  perf tools: Check maps for bpf programs
  perf bpf: Return NULL when RB tree lookup fails in perf_env__find_bpf_prog_info()
  tools include uapi: Sync sound/asound.h copy
  perf top: Always sample time to satisfy needs of use of ordered queuing
  perf evsel: Use hweight64() instead of hweight_long(attr.sample_regs_user)
  tools lib traceevent: Fix missing equality check for strcmp
  perf stat: Disable DIR_FORMAT feature for 'perf stat record'
  perf scripts python: export-to-sqlite.py: Fix use of parent_id in calls_view
  perf header: Fix lock/unlock imbalances when processing BPF/BTF info
  perf/x86: Fix incorrect PEBS_REGS
  perf/ring_buffer: Fix AUX record suppression
  perf/core: Fix the address filtering fix
  kprobes: Fix error check when reusing optimized probes

Pull x86 fixes from Ingo Molnar:
 "Misc fixes all over the place: a console spam fix, section attributes
  fixes, a KASLR fix, a TLB stack-variable alignment fix, a reboot
  quirk, boot options related warnings fix, an LTO fix, a deadlock fix
  and an RDT fix"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
  x86/cpu/bugs: Use __initconst for 'const' init data
  x86/mm/KASLR: Fix the size of the direct mapping section
  x86/Kconfig: Fix spelling mistake "effectivness" -> "effectiveness"
  x86/mm/tlb: Revert "x86/mm: Align TLB invalidation info"
  x86/reboot, efi: Use EFI reboot for Acer TravelMate X514-51T
  x86/mm: Prevent bogus warnings with "noexec=off"
  x86/build/lto: Fix truncated .bss with -fdata-sections
  x86/speculation: Prevent deadlock on ssb_state::lock
  x86/resctrl: Do not repeat rdtgroup mode initialization

Pull scheduler fixes from Ingo Molnar:
 "A deadline scheduler warning/race fix, and a cfs_period_us quota
  calculation workaround where the real fix looks too involved to merge
  immediately"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Correctly handle active 0-lag timers
  sched/fair: Limit sched_cfs_period_timer() loop to avoid hard lockup

Pull locking fixes from Ingo Molnar:
 "A lockdep warning fix and a script execution fix when atomics are
  generated"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/atomics: Don't assume that scripts are executable
  locking/lockdep: Make lockdep_unregister_key() honor 'debug_locks' again

Pull cgroup fix from Tejun Heo:
 "A patch to fix a RCU imbalance error in the devices cgroup
  configuration error path"

* 'for-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  device_cgroup: fix RCU imbalance in error case

Pull percpu fixlet from Dennis Zhou:
 "This stops printing the base address of percpu memory on
  initialization"

* 'for-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu:
  percpu: stop printing kernel addresses

Pull tty/serial fixes from Greg KH:
 "Here are five small fixes for some tty/serial/vt issues that have been
  reported.

  The vt one has been around for a while, it is good to finally get that
  resolved. The others fix a build warning that showed up in 5.1-rc1,
  and resolve a problem in the sh-sci driver.

  Note, the second patch for build warning fix for the sc16is7xx driver
  was just applied to the tree, as it resolves a problem with the
  previous patch to try to solve the issue. It has not shown up in
  linux-next yet, unlike all of the other patches, but it has passed
  0-day testing and everyone seems to agree that it is correct"

* tag 'tty-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  sc16is7xx: put err_spi and err_i2c into correct #ifdef
  vt: fix cursor when clearing the screen
  sc16is7xx: move label 'err_spi' to correct section
  serial: sh-sci: Fix HSCIF RX sampling point adjustment
  serial: sh-sci: Fix HSCIF RX sampling point calculation

Merge misc fixes from Andrew Morton:
 "16 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
  mm/kmemleak.c: fix unused-function warning
  init: initialize jump labels before command line option parsing
  kernel/watchdog_hld.c: hard lockup message should end with a newline
  kcov: improve CONFIG_ARCH_HAS_KCOV help text
  mm: fix inactive list balancing between NUMA nodes and cgroups
  mm/hotplug: treat CMA pages as unmovable
  proc: fixup proc-pid-vm test
  proc: fix map_files test on F29
  mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
  mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
  mm: swapoff: shmem_unuse() stop eviction without igrab()
  mm: swapoff: take notice of completion sooner
  mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
  mm: swapoff: shmem_find_swap_entries() filter out other types
  slab: store tagged freelist for off-slab slabmgmt

Pull staging and IIO fixes from Greg KH:
 "Here is a bunch of IIO driver fixes, and some smaller staging driver
  fixes, for 5.1-rc6. The IIO fixes were delayed due to my vacation, but
  all resolve a number of reported issues and have been in linux-next
  for a few weeks with no reported issues.

  The other staging driver fixes are all tiny, resolving some reported
  issues in the comedi and most drivers, as well as some erofs fixes.

  All of these patches have been in linux-next with no reported issues"

* tag 'staging-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (24 commits)
  staging: comedi: ni_usb6501: Fix possible double-free of ->usb_rx_buf
  staging: comedi: ni_usb6501: Fix use of uninitialized mutex
  staging: erofs: fix unexpected out-of-bound data access
  staging: comedi: vmk80xx: Fix possible double-free of ->usb_rx_buf
  staging: comedi: vmk80xx: Fix use of uninitialized semaphore
  staging: most: core: use device description as name
  iio: core: fix a possible circular locking dependency
  iio: ad_sigma_delta: select channel when reading register
  iio: pms7003: select IIO_TRIGGERED_BUFFER
  iio: cros_ec: Fix the maths for gyro scale calculation
  iio: adc: xilinx: prevent touching unclocked h/w on remove
  iio: adc: xilinx: fix potential use-after-free on probe
  iio: adc: xilinx: fix potential use-after-free on remove
  iio: dac: mcp4725: add missing powerdown bits in store eeprom
  io: accel: kxcjk1013: restore the range after resume.
  iio:chemical:bme680: Fix SPI read interface
  iio:chemical:bme680: Fix, report temperature in millidegrees
  iio: chemical: fix missing Kconfig block for sgp30
  iio: adc: at91: disable adc channel interrupt in timeout case
  iio: gyro: mpu3050: fix chip ID reading
  ...

Pull char/misc fixes from Greg KH:
 "Here are four small misc driver fixes for 5.1-rc6.

  Nothing major at all, they fix up a Kconfig issues, a SPDX invalid
  license tag, and two tiny bugfixes.

  All have been in linux-next for a while with no reported issues"

* tag 'char-misc-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  drivers: power: supply: goldfish_battery: Fix bogus SPDX identifier
  extcon: ptn5150: fix COMPILE_TEST dependencies
  misc: fastrpc: add checked value for dma_set_mask
  habanalabs: remove low credit limit of DMA #0

bvec->bv_offset may be bigger than PAGE_SIZE sometimes, such as,
when one bio is splitted in the middle of one bvec via bio_split(),
and bi_iter.bi_bvec_done is used to build offset of the 1st bvec of
remained bio. And the remained bio's bvec may be re-submitted to fs
layer via ITER_IBVEC, such as loop and nvme-loop.

So we have to make sure that every bvec's offset is less than
PAGE_SIZE from bio_for_each_segment_all() because some drivers(loop,
nvme-loop) passes the splitted bvec to fs layer via ITER_BVEC.

This patch fixes this issue reported by Zhang Yi When running nvme/011.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Yi Zhang <yi.zhang@redhat.com>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixes: 6dc4f100 ("block: allow bio_for_each_segment_all() to iterate over multi-page bvec")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

all_q_node has not been used since commit 4b855ad3 ("blk-mq: Create
hctx for each present CPU"), so remove it.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull input updates from Dmitry Torokhov:

 - several new key mappings for HID

 - a host of new ACPI IDs used to identify Elan touchpads in Lenovo
   laptops

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: snvs_pwrkey - initialize necessary driver data before enabling IRQ
  HID: input: add mapping for "Toggle Display" key
  HID: input: add mapping for "Full Screen" key
  HID: input: add mapping for keyboard Brightness Up/Down/Toggle keys
  HID: input: add mapping for Expose/Overview key
  HID: input: fix mapping of aspect ratio key
  [media] doc-rst: switch to new names for Full Screen/Aspect keys
  Input: document meanings of KEY_SCREEN and KEY_ZOOM
  Input: elan_i2c - add hardware ID for multiple Lenovo laptops

The "ENERGY_PERF_BIAS: Set to 'normal', was 'performance'" message triggers
on pretty much every Intel machine. The purpose of log messages with
a warning level is to notify the user of something which potentially is
a problem, or at least somewhat unexpected.

This message clearly does not match those criteria, so lower its log
priority from warning to info.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20181230172715.17469-1-hdegoede@redhat.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Merge tag 'perf-urgent-for-mingo-5.1-20190419' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Pull perf/urgent fixes from Arnaldo Carvalho de Melo:

perf top:

  Jiri Olsa:

  - Fix 'perf top --pid', it needs PERF_SAMPLE_TIME since we switched to using
    a different thread to sort the events and then even for just a single
    thread we now need timestamps.

BPF:

  Jiri Olsa:

  - Fix bpf_prog and btf lookup functions failure path to to properly return
    NULL.

  - Fix side band thread draining, used to process PERF_RECORD_BPF_EVENT
    metadata records.

core:

  Jiri Olsa:

  - Fix map lookup by name to get a refcount when the name is already in
    the tree. Found

  Song Liu:

  - Fix __map__is_kmodule() by taking into account recently added BPF
    maps.

UAPI:

  Arnaldo Carvalho de Melo:

  - Sync sound/asound.h copy
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>