Merge branch 'drm-nouveau-fixes-3.9' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next

Oops fixers.
* 'drm-nouveau-fixes-3.9' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nouveau: fix NULL ptr dereference from nv50_disp_intr()
  drm/nouveau: fix handling empty channel list in ioctl's

One locking regression fix, and a couple of other i915 ones.

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm: don't unlock in the addfb error paths
  drm/i915: Fix build failure
  drm/i915: Be sure to turn hsync/vsync back on at crt enable (v2)
  drm/i915: duct-tape locking when eDP init fails

Make sure that msg pointer is set back to error value in case of
MSG_COPY flag is set and desired message to copy wasn't found.  This
garantees that msg is either a error pointer or a copy address.

Otherwise the last message in queue will be freed without unlinking from
the queue (which leads to memory corruption) and the dummy allocated
copy won't be released.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC bug fixes from Arnd Bergmann:
 "After a quiet set of fixes for 3.9-rc4, a lot of people woke up and
  sent urgent fixes for 3.9.  I pushed back on a number of them that got
  deferred to 3.10, but these are the ones that seemed important.

  Regression in 3.9:

   - Multiple regressions in OMAP2+ clock cleanup
   - SH-Mobile frame buffer bug fix that merged here because of
     maintainer MIA
   - ux500 prcmu changes broke DT booting
   - MMCI duplicated regulator setup on ux500
   - New ux500 clock driver broke ethernet on snowball
   - Local interrupt driver for mvebu broke ethernet
   - MVEBU GPIO driver did not get set up right on Orion DT
   - incorrect interrupt number on Orion crypto for DT

  Long-standing bugs, including candidates for stable:

   - Kirkwood MMC needs to disable invalid card detect pins
   - MV SDIO pinmux was wrong on Mirabox
   - GoFlex Net board file needs to set NAND chip delay
   - MSM timer restart race
   - ep93xx early debug code broke in 3.7
   - i.MX CPU hotplug race
   - Incorrect clock setup for OMAP1 USB
   - Workaround for bad clock setup by some old OMAP4 boot loaders
   - Static I/O mappings on cns3xxx since 3.2"

* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: cns3xxx: fix mapping of private memory region
  arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
  arm: orion5x: correct IRQ used in dtsi for mv_cesa
  arm: orion5x: fix orion5x.dtsi gpio parameters
  ARM: Kirkwood: fix unused mvsdio gpio pins
  arm: mvebu: Use local interrupt only for the timer 0
  ARM: kirkwood: Fix chip-delay for GoFlex Net
  ARM: ux500: Enable the clock controlling Ethernet on Snowball
  ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
  ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
  fbdev: sh_mobile_lcdc: fixup B side hsync adjust settings
  ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
  ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
  ARM: msm: Stop counting before reprogramming clockevent
  ARM: ep93xx: Fix wait for UART FIFO to be empty
  ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
  ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
  ARM: OMAP4: clock data: lock USB DPLL on boot
  ARM: OMAP1: fix USB host on 1710

Pull nfsd bugfix from J Bruce Fields:
 "An xdr decoding error--thanks, Toralf Förster, and Trinity!"

* 'for-3.9' of git://linux-nfs.org/~bfields/linux:
  nfsd4: reject "negative" acl lengths

From Anton Vorontsov <anton@enomsg.org>:

This tag includes Mac Lin's work to revive CNS3xxx booting:

 "Since commit 0536bdf3 (ARM: move iotable mappings within the vmalloc
 region), [...] the pre-defined iotable mappings is not in the vmalloc
 region. [...] move the iotable mappings into the vmalloc region, and
 merge the MPCore private memory region (containing the SCU, the GIC and
 the TWD) as a single region."

Plus there is a small cosmetic fix, also from Mac Lin.

* tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx:
  ARM: cns3xxx: fix mapping of private memory region

[arnd: dropped the cosmetic fix from the merge as it is not needed for 3.9]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull virtio fixes from Rusty Russell:
 "One reversion, a tiny leak fix, and a cc:stable locking fix, in two
  parts"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  virtio: console: add locking around c_ovq operations
  virtio: console: rename cvq_lock to c_ivq_lock
  hw_random: free rng_buffer at module exit
  Revert "virtio_console: Initialize guest_connected=true for rproc_serial"

struct block_device lifecycle is defined by its inode (see fs/block_dev.c) -
block_device allocated first time we access /dev/loopXX and deallocated on
bdev_destroy_inode. When we create the device "losetup /dev/loopXX afile"
we want that block_device stay alive until we destroy the loop device
with "losetup -d".

But because we do not hold /dev/loopXX inode its counter goes 0, and
inode/bdev can be destroyed at any moment. Usually it happens at memory
pressure or when user drops inode cache (like in the test below). When later in
loop_clr_fd() we want to use bdev we have use-after-free error with following
stack:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000280
  bd_set_size+0x10/0xa0
  loop_clr_fd+0x1f8/0x420 [loop]
  lo_ioctl+0x200/0x7e0 [loop]
  lo_compat_ioctl+0x47/0xe0 [loop]
  compat_blkdev_ioctl+0x341/0x1290
  do_filp_open+0x42/0xa0
  compat_sys_ioctl+0xc1/0xf20
  do_sys_open+0x16e/0x1d0
  sysenter_dispatch+0x7/0x1a

To prevent use-after-free we need to grab the device in loop_set_fd()
and put it later in loop_clr_fd().

The issue is reprodusible on current Linus head and v3.3. Here is the test:

  dd if=/dev/zero of=loop.file bs=1M count=1
  while [ true ]; do
    losetup /dev/loop0 loop.file
    echo 2 > /proc/sys/vm/drop_caches
    losetup -d /dev/loop0
  done

[ Doing bdgrab/bput in loop_set_fd/loop_clr_fd is safe, because every
  time we call loop_set_fd() we check that loop_device->lo_state is
  Lo_unbound and set it to Lo_bound If somebody will try to set_fd again
  it will get EBUSY.  And if we try to loop_clr_fd() on unbound loop
  device we'll get ENXIO.

  loop_set_fd/loop_clr_fd (and any other loop ioctl) is called under
  loop_device->lo_ctl_mutex. ]
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull tegra clock driver fix from Mike Turquette:
 "Missing base address in Tegra clock driver results in non-operational
  PCIe.  On some devices this means that Ethernet will go uninitialized
  and other devices will fail.  This pull request fixes it with a single
  patch to pass the proper base address in the Tegra clock driver."

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
  clk: tegra: Allow PLLE training to succeed

Pull FCoE fixes from Robert Love:
 "Critical patches to fix FCoE VN2VN mode with new interfaces targeting
  3.9-rc"

* tag 'for-3.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rwlove/fcoe:
  libfcoe: Fix fcoe_sysfs VN2VN mode
  libfc, fcoe, bnx2fc: Split fc_disc_init into fc_disc_{init, config}
  libfc, fcoe, bnx2fc: Always use fcoe_disc_init for discovery layer initialization
  fcoe: Fix deadlock between create and destroy paths
  bnx2fc: Make the fcoe_cltr the SCSI host parent

Under some circumstances the PLLE needs to be retrained, in which case
access to the PMC registers is required. Fix this by passing a pointer
to the PMC registers instead of NULL when registering the PLLE clock.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

Pull arch/tile fix from Chris Metcalf:
 "This change allows newer Tilera boot tools to work correctly with
  current (and stable) kernels by using the right filename to get the
  initramfs from the Tilera hypervisor filesystem."

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: expect new initramfs name from hypervisor file system

Pull networking fixes from David Miller:

 1) sadb_msg prepared for IPSEC userspace forgets to initialize the
    satype field, fix from Nicolas Dichtel.

 2) Fix mac80211 synchronization during station removal, from Johannes
    Berg.

 3) Fix IPSEC sequence number notifications when they wrap, from Steffen
    Klassert.

 4) Fix cfg80211 wdev tracing crashes when add_virtual_intf() returns an
    error pointer, from Johannes Berg.

 5) In mac80211, don't call into the channel context code with the
    interface list mutex held.  From Johannes Berg.

 6) In mac80211, if we don't actually associate, do not restart the STA
    timer, otherwise we can crash.  From Ben Greear.

 7) Missing dma_mapping_error() check in e1000, ixgb, and e1000e.  From
    Christoph Paasch.

 8) Fix sja1000 driver defines to not conflict with SH port, from Marc
    Kleine-Budde.

 9) Don't call il4965_rs_use_green with a NULL station, from Colin Ian
    King.

10) Suspend/Resume in the FEC driver fail because the buffer descriptors
    are not initialized at all the moments in which they should.  Fix
    from Frank Li.

11) cpsw and davinci_emac drivers both use the wrong interface to
    restart a stopped TX queue.  Use netif_wake_queue not
    netif_start_queue, the latter is for initialization/bringup not
    active management of the queue.  From Mugunthan V N.

12) Fix regression in rate calculations done by
    psched_ratecfg_precompute(), missing u64 type promotion.  From
    Sergey Popovich.

13) Fix length overflow in tg3 VPD parsing, from Kees Cook.

14) AOE driver fails to allocate enough headroom, resulting in crashes.
    Fix from Eric Dumazet.

15) RX overflow happens too quickly in sky2 driver because pause packet
    thresholds are not programmed correctly.  From Mirko Lindner.

16) Bonding driver manages arp_interval and miimon settings incorrectly,
    disabling one unintentionally disables both.  Fix from Nikolay
    Aleksandrov.

17) smsc75xx drivers don't program the RX mac properly for jumbo frames.
    Fix from Steve Glendinning.

18) Fix off-by-one in Codel packet scheduler.  From Vijay Subramanian.

19) Fix packet corruption in atl1c by disabling MSI support, from Hannes
    Frederic Sowa.

20) netdev_rx_handler_unregister() needs a synchronize_net() to fix
    crashes in bonding driver unload stress tests.  From Eric Dumazet.

21) rxlen field of ks8851 RX packet descriptors not interpreted
    correctly (it is 12 bits not 16 bits, so needs to be masked after
    shifting the 32-bit value down 16 bits).  Fix from Max Nekludov.

22) Fix missed RX/TX enable in sh_eth driver due to mishandling of link
    change indications.  From Sergei Shtylyov.

23) Fix crashes during spurious ECI interrupts in sh_eth driver, also
    from Sergei Shtylyov.

24) dm9000 driver initialization is done wrong for revision B devices
    with DSP PHY, from Joseph CHANG.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
  DM9000B: driver initialization upgrade
  sh_eth: make 'link' field of 'struct sh_eth_private' *int*
  sh_eth: workaround for spurious ECI interrupt
  sh_eth: fix handling of no LINK signal
  ks8851: Fix interpretation of rxlen field.
  net: add a synchronize_net() in netdev_rx_handler_unregister()
  MAINTAINERS: Update netxen_nic maintainers list
  atl1e: drop pci-msi support because of packet corruption
  net: fq_codel: Fix off-by-one error
  net: calxedaxgmac: Wake-on-LAN fixes
  net: calxedaxgmac: fix rx ring handling when OOM
  net: core: Remove redundant call to 'nf_reset' in 'dev_forward_skb'
  smsc75xx: fix jumbo frame support
  net: fix the use of this_cpu_ptr
  bonding: fix disabling of arp_interval and miimon
  ipv6: don't accept node local multicast traffic from the wire
  sky2: Threshold for Pause Packet is set wrong
  sky2: Receive Overflows not counted
  aoe: reserve enough headroom on skbs
  line up comment for ndo_bridge_getlink
  ...

Fix bug for DM9000 revision B which contain a DSP PHY

DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY,
So need extra change in initialization, For
explicity PHY Reset and PHY init parameter, and
first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe().

Following DM9000_NCR reset cause by dm9000_open() clear the
NCR_MAC_LBK bit.

Without this fix, Power-up FIFO pointers error happen around 2%
rate among Davicom's customers' boards. With this fix, All above
cases can be solved.
Signed-off-by: Joseph CHANG <josright123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'link' field of 'struct sh_eth_private' has type 'enum phy_state' while the
'link' field of 'struct phy_device' is merely *int* (having values 0 and 1) and
the former field gets assigned from the latter. Make the field match, getting
rid of incorrectly used PHY_DOWN value in assignments/comparisons.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its
mask in EESIPR register. I can 100% reproduce it with the following scenario:
target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device
but doesn't get a proper reply and then succeeds with on-board SMC chip; then
I login and try to bring up the SoC Ether device with 'ifconfig', and I get
an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt
mask in EESIPR register is all 0), if that interrupt is accompanied by a pending
EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx()
because sh_eth_ring_init() hasn't been called yet!

The solution I worked out is the following: in sh_eth_interrupt(), mask the
interrupt status from EESR register with the interrupt mask from EESIPR register
in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit
in this mask set because we always need to fully handle EESR.ECI interrupt in
sh_eth_error() in order to quench it (as it doesn't get cleared by just writing
1 to the this bit as all the other interrupts).

While at it, remove unneeded initializer for 'intr_status' variable and give it
*unsigned long* type, matching the type of sh_eth_read()'s result; fix comment.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Max Filippov <max.filippov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code handling the absent LINK signal (or the absent PSR register -- which
reflects the state of this signal) is quite naive and has probably never really
worked.  It's probably enough to say that this code is executed only on the LINK
change interrupt (sic!) but even if we actually have the signal and choose to
ignore it (it might be connected to PHY's link/activity LED output as on the
Renesas BOCK-W board), sh_eth_adjust_link() on which this code relies to update
'mdp->link' gets executed later than the LINK change interrupt where it is
checked, and so RX/TX never get enabled via ECMR register.

So, ignore the LINK changed interrupt iff LINK signal is absent (or just chosen
not to be used) or PSR register is absent, and enable/disable RX/TX directly in
sh_eth_adjust_link() in this case.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull slave-dmaengine fixes from Vinod Koul:
 "Two fixes for slave-dmaengine.

  The first one is for making slave_id value correct for dw_dmac and
  the other one fixes the endieness in DT parsing"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dw_dmac: adjust slave_id accordingly to request line base
  dmaengine: dw_dma: fix endianess for DT xlate function

Pull media fixes from Mauro Carvalho Chehab:
 "For a some fixes for Kernel 3.9:
   - subsystem build fix when VIDEO_DEV=y, VIDEO_V4L2=m and I2C=m
   - compilation fix for arm multiarch preventing IR_RX51 to be selected
   - regression fix at bttv crop logic
   - s5p-mfc/m5mols/exynos: a few fixes for cameras on exynos hardware"

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] [REGRESSION] bt8xx: Fix too large height in cropcap
  [media] fix compilation with both V4L2 and I2C as 'm'
  [media] m5mols: Fix bug in stream on handler
  [media] s5p-fimc: Do not attempt to disable not enabled media pipeline
  [media] s5p-mfc: Fix encoder control 15 issue
  [media] s5p-mfc: Fix frame skip bug
  [media] s5p-fimc: send valid m2m ctx to fimc_m2m_job_finish
  [media] exynos-gsc: send valid m2m ctx to gsc_m2m_job_finish
  [media] fimc-lite: Fix the variable type to avoid possible crash
  [media] fimc-lite: Initialize 'step' field in fimc_lite_ctrl structure
  [media] ir: IR_RX51 only works on OMAP2

Pull block fixes from Jens Axboe:
 "Alright, this time from 10K up in the air.

  Collection of fixes that have been queued up since the merge window
  opened, hence postponed until later in the cycle.  The pull request
  contains:

   - A bunch of fixes for the xen blk front/back driver.

   - A round of fixes for the new IBM RamSan driver, fixing various
     nasty issues.

   - Fixes for multiple drives from Wei Yongjun, bad handling of return
     values and wrong pointer math.

   - A fix for loop properly killing partitions when being detached."

* tag 'for-linus-20130331' of git://git.kernel.dk/linux-block: (25 commits)
  mg_disk: fix error return code in mg_probe()
  rsxx: remove unused variable
  rsxx: enable error return of rsxx_eeh_save_issued_dmas()
  block: removes dynamic allocation on stack
  Block: blk-flush: Fixed indent code style
  cciss: fix invalid use of sizeof in cciss_find_cfgtables()
  loop: cleanup partitions when detaching loop device
  loop: fix error return code in loop_add()
  mtip32xx: fix error return code in mtip_pci_probe()
  xen-blkfront: remove frame list from blk_shadow
  xen-blkfront: pre-allocate pages for requests
  xen-blkback: don't store dev_bus_addr
  xen-blkfront: switch from llist to list
  xen-blkback: fix foreach_grant_safe to handle empty lists
  xen-blkfront: replace kmalloc and then memcpy with kmemdup
  xen-blkback: fix dispatch_rw_block_io() error path
  rsxx: fix missing unlock on error return in rsxx_eeh_remap_dmas()
  Adding in EEH support to the IBM FlashSystem 70/80 device driver
  block: IBM RamSan 70/80 error message bug fix.
  block: IBM RamSan 70/80 branding changes.
  ...

This reverts commit 6aa97070.

Commit 6aa97070 ("lockdep: check that no locks held at freeze time")
causes problems with NFS root filesystems.  The failures were noticed on
OMAP2 and 3 boards during kernel init:

  [ BUG: swapper/0/1 still has locks held! ]
  3.9.0-rc3-00344-ga937536b #1 Not tainted
  -------------------------------------
  1 lock held by swapper/0/1:
   #0:  (&type->s_umount_key#13/1){+.+.+.}, at: [<c011e84c>] sget+0x248/0x574

  stack backtrace:
    rpc_wait_bit_killable
    __wait_on_bit
    out_of_line_wait_on_bit
    __rpc_execute
    rpc_run_task
    rpc_call_sync
    nfs_proc_get_root
    nfs_get_root
    nfs_fs_mount_common
    nfs_try_mount
    nfs_fs_mount
    mount_fs
    vfs_kern_mount
    do_mount
    sys_mount
    do_mount_root
    mount_root
    prepare_namespace
    kernel_init_freeable
    kernel_init

Although the rootfs mounts, the system is unstable.  Here's a transcript
from a PM test:

  http://www.pwsan.com/omap/testlogs/test_v3.9-rc3/20130317194234/pm/37xxevm/37xxevm_log.txt

Here's what the test log should look like:

  http://www.pwsan.com/omap/testlogs/test_v3.8/20130218214403/pm/37xxevm/37xxevm_log.txt

Mailing list discussion is here:

  http://lkml.org/lkml/2013/3/4/221

Deal with this for v3.9 by reverting the problem commit, until folks can
figure out the right long-term course of action.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: <maciej.rutecki@gmail.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ben Chan <benchan@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull SCSI target fixes from Nicholas Bellinger:
 "This includes the bug-fix for a >= v3.8-rc1 regression specific to
  iscsi-target persistent reservation conflict handling (CC'ed to
  stable), and a tcm_vhost patch to drop VIRTIO_RING_F_EVENT_IDX usage
  so that in-flight qemu vhost-scsi-pci device code can detect the
  proper vhost feature bits.

  Also, there are two more tcm_vhost patches still being discussed by
  MST and Asias for v3.9 that will be required for the in-flight qemu
  vhost-scsi-pci device patch to function properly, and that should
  (hopefully) be the last target fixes for this round."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
  tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit

Since commit 0536bdf3 (ARM: move iotable mappings within the vmalloc
region), the Cavium CNS3xxx cannot boot anymore.

This is caused by the pre-defined iotable mappings is not in the vmalloc
region. This patch move the iotable mappings into the vmalloc region, and
merge the MPCore private memory region (containing the SCU, the GIC and
the TWD) as a single region.
Signed-off-by: Mac Lin <mkl0301@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Cc: stable@vger.kernel.org [v3.3+]

When multiple ovq operations are being performed (lots of open/close
operations on virtio_console fds), the __send_control_msg() function can
get confused without locking.

A simple recipe to cause badness is:
* create a QEMU VM with two virtio-serial ports
* in the guest, do
  while true;do echo abc >/dev/vport0p1;done
  while true;do echo edf >/dev/vport0p2;done

In one run, this caused a panic in __send_control_msg().  In another, I
got

   virtio_console virtio0: control-o:id 0 is not a head!

This also results repeated messages similar to these on the host:

  qemu-kvm: virtio-serial-bus: Unexpected port id 478762112 for device virtio-serial-bus.0
  qemu-kvm: virtio-serial-bus: Unexpected port id 478762368 for device virtio-serial-bus.0
Reported-by: FuXiangChun <xfu@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: Asias He <asias@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org

The cvq_lock was taken for the c_ivq.  Rename the lock to make that
obvious.

We'll also add a lock around the c_ovq in the next commit, so there's no
ambiguity.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org

On some hardware configurations we have got the request line with the offset.
The patch introduces convert_slave_id() helper for that cases. The request line
base is came from the driver data provided by the platform_device_id table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

As reported by Wu Fengguang's build robot tracking sparse warnings, the
dma_spec arguments in the dw_dma_xlate are already byte swapped on
little-endian platforms and must not get swapped again. This code is
currently not used anywhere, but will be used in Linux 3.10 when the
ARM SPEAr platform starts using the generic DMA DT binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The Adam Belay's e-mail address in MAINTAINERS under PNP SUPPORT
is not valid any more and I started to maintain that code in the
meantime as a matter of fact, so list myself as a maintainer of it
along with Bjorn and remove the Adam's entry from it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

According to the Datasheet (page 52):
15-12 Reserved
11-0 RXBC Receive Byte Count
This field indicates the present received frame byte size.

The code has a bug:
                 rxh = ks8851_rdreg32(ks, KS_RXFHSR);
                 rxstat = rxh & 0xffff;
                 rxlen = rxh >> 16; // BUG!!! 0xFFF mask should be applied
Signed-off-by: Max Nekludov <Max.Nekludov@us.elster.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 35d48903 (bonding: fix rx_handler locking) added a race
in bonding driver, reported by Steven Rostedt who did a very good
diagnosis :

<quoting Steven>

I'm currently debugging a crash in an old 3.0-rt kernel that one of our
customers is seeing. The bug happens with a stress test that loads and
unloads the bonding module in a loop (I don't know all the details as
I'm not the one that is directly interacting with the customer). But the
bug looks to be something that may still be present and possibly present
in mainline too. It will just be much harder to trigger it in mainline.

In -rt, interrupts are threads, and can schedule in and out just like
any other thread. Note, mainline now supports interrupt threads so this
may be easily reproducible in mainline as well. I don't have the ability
to tell the customer to try mainline or other kernels, so my hands are
somewhat tied to what I can do.

But according to a core dump, I tracked down that the eth irq thread
crashed in bond_handle_frame() here:

        slave = bond_slave_get_rcu(skb->dev);
        bond = slave->bond; <--- BUG

the slave returned was NULL and accessing slave->bond caused a NULL
pointer dereference.

Looking at the code that unregisters the handler:

void netdev_rx_handler_unregister(struct net_device *dev)
{

        ASSERT_RTNL();
        RCU_INIT_POINTER(dev->rx_handler, NULL);
        RCU_INIT_POINTER(dev->rx_handler_data, NULL);
}

Which is basically:
        dev->rx_handler = NULL;
        dev->rx_handler_data = NULL;

And looking at __netif_receive_skb() we have:

        rx_handler = rcu_dereference(skb->dev->rx_handler);
        if (rx_handler) {
                if (pt_prev) {
                        ret = deliver_skb(skb, pt_prev, orig_dev);
                        pt_prev = NULL;
                }
                switch (rx_handler(&skb)) {

My question to all of you is, what stops this interrupt from happening
while the bonding module is unloading?  What happens if the interrupt
triggers and we have this:

        CPU0                    CPU1
        ----                    ----
  rx_handler = skb->dev->rx_handler

                        netdev_rx_handler_unregister() {
                           dev->rx_handler = NULL;
                           dev->rx_handler_data = NULL;

  rx_handler()
   bond_handle_frame() {
    slave = skb->dev->rx_handler;
    bond = slave->bond; <-- NULL pointer dereference!!!

What protection am I missing in the bond release handler that would
prevent the above from happening?

</quoting Steven>

We can fix bug this in two ways. First is adding a test in
bond_handle_frame() and others to check if rx_handler_data is NULL.

A second way is adding a synchronize_net() in
netdev_rx_handler_unregister() to make sure that a rcu protected reader
has the guarantee to see a non NULL rx_handler_data.

The second way is better as it avoids an extra test in fast path.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Paul E. McKenney <paulmck@us.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Add myself to netxen_nic maintainers list
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Usage of pci-msi results in corrupted dma packet transfers to the host.
Reported-by: rebelyouth <rebelyouth.hacklab@gmail.com>
Cc: Huang, Xiong <xiong@qca.qualcomm.com>
Tested-by: Christian Sünkenberg <christian.suenkenberg@student.kit.edu>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, we hold a max of sch->limit -1 number of packets instead of
sch->limit packets. Fix this off-by-one error.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

WOL is broken because the magic packet status bit is getting set rather
than the enable bit. The PMT interrupt is not getting serviced because
the PMT interrupt is also enabled on the global interrupt, but not
cleared by the global interrupt and the global interrupt is higher
priority. This fixes both of these issues to get WOL working.

There's still a problem with receive after resume, but at least now we
can wake-up.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If skb allocation for the rx ring fails repeatedly, we can reach a point
were the ring is empty. In this condition, the driver is out of sync with
the h/w. While this has always been possible, the removal of the skb
recycling seems to have made triggering this problem easier.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'nf_reset' is called just prior calling 'netif_rx'.
No need to call it twice.
Reported-by: Igor Michailov <rgohita@gmail.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables RX of jumbo frames for LAN7500.

Previously the driver would transmit jumbo frames succesfully but
would drop received jumbo frames (incrementing the interface errors
count).

With this patch applied the device can succesfully receive jumbo
frames up to MTU 9000 (9014 bytes on the wire including ethernet
header).
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

flush_tasklet is not percpu var, and percpu is percpu var, and
	this_cpu_ptr(&info->cache->percpu->flush_tasklet)
is not equal to
	&this_cpu_ptr(info->cache->percpu)->flush_tasklet

1f743b07(use this_cpu_ptr per-cpu helper) introduced this bug.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current Tilera boot infrastructure now provides the initramfs
to Linux as a Tilera-hypervisor file named "initramfs", rather than
"initramfs.cpio.gz", as before.  (This makes it reasonable to use
other compression techniques than gzip on the file without having to
worry about the name causing confusion.)  Adapt to use the new name,
but also fall back to checking for the old name.

Cc'ing to stable so that older kernels will remain compatible with
newer Tilera boot infrastructure.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable@vger.kernel.org