Merge "pxa-dt for v4.3" from Robert Jarzmik:

This device-tree pxa update brings :
 - dma nodes after dmaengine pxa_dma driver merge
 - camera driver
 - usb host controller

* tag 'tags/pxa-dt-4.3' of https://github.com/rjarzmik/linux:
  ARM: dts: pxa: fix power i2c definition
  ARM: dts: pxa: add the usb host controller
  ARM: dts: pxa: add embedded pxa camera capture interface
  ARM: dts: pxa: add dma pxamci nodes to pxa3xx
  ARM: dts: pxa: add dma engine node to pxa3xx-nand
  ARM: dts: pxa: add dma controller
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v4.3-rockchip32-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Merge "Rockchip dts changes for 4.3, part1" from Heiko Stuebner:

This adds the board for the Netxeon R89 used in different TV-boxes and
the initial support for two Chromebooks from the veyron family.

Additionally a non-critical fix for the watchdog irq on rk3288, addition
of the gmac reset line, a ramp delay for the cpu regulator on the firefly
board and cpu affinity for the arm-pmu spi irqs.

* tag 'v4.3-rockchip32-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: add rk3288 arm-pmu irq affinity
  dt-bindings: document rk3368 R88 board from Rockchip
  ARM: dts: rockchip: add missing device_type = "memory" to boards
  ARM: dts: rockchip: add veyron-pinky board
  ARM: dts: rockchip: add veyron-jerry board
  ARM: dts: rockchip: add shared rk3288-veyron files
  ARM: dts: Add sbs-battery dts fragment used by chromebooks
  ARM: dts: rockchip: add Netxeon R89 board
  dt-bindings: add vendor prefix for Netxeon Technology
  ARM: dts: rockchip: fix rk3288 watchdog irq
  ARM: dts: rockchip: Add ramp delay for vdd_cpu in firefly board dts
  ARM: dts: rockchip: Add STMMAC reset signal in GMAC interface for rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge "Broadcom Device Tree changes for 4.3 (part 1)" from Florian Fainelli:

This pull request contains two changes:

- Ray adds the relevant clocks device tree nodes for Cygnus SoCs

- Rafal enables UART0 on BCM5301X routers where it has been verified to work
  correctly

* tag 'arm-soc/for-4.3/dts' of http://github.com/broadcom/stblinux:
  ARM: BCM5301X: Enable UART0 on tested devices
  ARM: dts: enable clock support for Broadcom Cygnus
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge "ARM: mvebu: dt changes for v4.3" from Gregory Clement:

mvebu dt changes for v4.3 (part #1)

- Update Armada 388 GP description
- Add Buffalo Linkstation  LS-WXL and LS-WSXL
- Fine-tune the L2 configuration for cortex A9 based SoC
- Update XOR definition for Armada 38x and 39x SoC

* tag 'mvebu-dt-4.3-1' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: update EEPROM description of Armada 388 GP
  ARM: mvebu: fix description of pwr-sata0 regulator on Armada 388 GP
  ARM: dts: add buffalo linkstation ls-wvl/vl
  ARM: dts: add buffalo linkstation ls-wxl/wsxl
  ARM: mvebu: use DT properties to fine-tune the L2 configuration
  ARM: mvebu: use armada-380-xor on Armada 38x and 39x
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge "LPC18xx DTS changes for 4.3" from Joachim Eastwood:

This patch set adds DT nodes for all the drivers that went upstream in
4.2 and should represent the bulk of DTS changes for 4.3.  All nodes
added are documented and some of patches carries a ack from subsystem
maintainer. It also features updates to the EA4357 dev- kit and a new
board from Ezequiel Garcia.

Note that there might be one more batch of DTS changes for 4.3 if any
new drivers goes upstream and also some changes for the Hitex eval board
might come.

* 'lpc18xx_43xx_dts_4.3' of https://github.com/manabian/linux-lpc:
  ARM: dts: add DT for CIAA LPC4337 industrial computer
  of: add vendor prefix for CIAA project
  ARM: dts: lpc4357-ea4357: add uart3
  ARM: dts: lpc4357-ea4357: add ethernet
  ARM: dts: lpc4357-ea4357: add gpio joystick
  ARM: dts: lpc4357-ea4357: add mmcsd
  ARM: dts: lpc4357-ea4357: add pinctrl and uart0 muxing
  ARM: dts: lpc18xx: add usb nodes
  ARM: dts: lpc18xx: add ethernet node
  ARM: dts: lpc18xx: add creg (syscon) node
  ARM: dts: lpc18xx: add mmcsd node
  ARM: dts: lpc18xx: add can nodes
  ARM: dts: lpc18xx: add ssp nodes
  ARM: dts: lpc18xx: add gpio node
  ARM: dts: lpc18xx: add pinctrl node
  ARM: dts: lpc18xx: add uart new compat string and clk names
  ARM: dts: lpc18xx: add cgu and ccu clock-controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>

The rk3288 uses spi irqs for the arm-pmu on individual cpu cores, so needs
the affinity to them defined.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>

The initial board containing the rk3368 ARM64 soc.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The memory node is supposed to contain a device_type property marking
it as memory. The currently included boards miss this property.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

While pinky was one of the earlier development models, is on the list
of endangered species today and nearly extinct, I want to keep mine
around for the foreseeable future after spending all the time making a
nice hole into the base below the dut-connector.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The Hisense Chromebook C11, also named jerry.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>

This adds the shared devicetree files for the Veyron device family.
They are split, as not all veyron devices are chromebooks and
not all contain a sd-card slot.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>

Merge tag 'omap-for-v4.3/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Merge "omap dts changes for v4.3, part 1" from Tony Lindgren:

Omap dts changes for v4.3 merge window. There are also related
changes for reemoteproc platform_data and audio options for
omap2plus_defconfig to keep audio working when changing boards
to use SIMPLE_CARD. The summary of changes is:

- A large set of audio related changes for SIMPLE_CARD from
  Peter Ujfalusi <peter.ujfalusi@ti.com> for am335x and am437x

- Pinctrl dts defines for dra7 virtual mode to configure timings

- Change to use cpsw slave0 for dra7 Ethernet

- Remove unconfigured and wrong l3-mux entry for dm816x

- Add support for Gumstix Palo35 and TobiDuo boards, and  Overo
  PoP NAND and McBSP2

- Start using new HDMI binding for tilcdc

- Start using new sDMA crossbar for dra7

- Start using rproc for am335x and am437x M3 coprocessor

* tag 'omap-for-v4.3/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (32 commits)
  ARM: dts: am335x-evm: Switch using simple-audio-card for audio support
  ARM: dts: am335x-evm: Add sleep pin settings for mcasp1
  ARM: dts: am335x-evm: Rename pinctrl section for McASP1
  ARM: dts: am335x-evm: Fix mcasp1 node's indentation
  ARM: dts: am335x-evmsk: Switch using simple-audio-card for audio support
  ARM: dts: am335x-evmsk: Add sleep pin settings for mcasp1
  ARM: dts: am335x-evmsk: Fix mcasp1 node's indentation
  ARM: dts: am437x-gp-evm: Enable analog audio via simple-card
  ARM: dts: am437x-gp-evm: McASP1 node for audio support
  ARM: dts: am437x-gp-evm: Add node for tlv320aic3106 audio codec
  ARM: dts: am437x-gp-evm: Rename fixed regulator vmmcsd_fixed to evm_v3_3d
  ARM: dts: am437x-gp-evm: Add gpio-hog for configuring the display/audio mux
  ARM: dts: am43xx-epos-evm: Enable analog audio via simple-card
  ARM: dts: am43xx-epos-evm: Add node for tlv320aic3111 audio codec
  ARM: dts: am43xx-epos-evm: McASP1 node for audio support
  ARM: dts: am43xx-epos-evm: Add regulator for VBAT and DCDC4 of tps65218
  ARM: dts: am43xx-epos-evm: Add gpio-hog for configuring the display/audio mux
  ARM: dts: am437x-sk-evm: Switch using simple-audio-card for audio support
  ARM: dts: am437x-sk-evm: Add sleep pin settings for mcasp1
  ARM: omap2plus_defconfig: Enable audio related config options
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch creates a sbs-battery fragment for batteries connected
to the i2c tunnel of the cros-ec embedded controller.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Douglas Anderson <dianders@chromium.org>

This board is used in some TV-boxes like for example the Beelink R89 or
Tronsmart R28.

The board itself follows the reference design for the most part. But
there are no schematics available it seems, so some things should be
taken with a grain of salt.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Romain Perier <romain.perier@gmail.com>

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Romain Perier <romain.perier@gmail.com>

Add basic support for CIAA (Argentine Open Industrial Computer)
LPC4337 board. This commit enables the following peripherals:
  * UART
  * SSP
  * Ethernet
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>

CIAA stands for Argentine Open Industrial Computer. The CIAA project
is an initiative sponsored by universities and private companies.
Its main goal is to promote local embedded systems development.

Among other devices, the project developed a NXP LPC4337-based
reference design.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>

Enable UART3 that is routed to the J17 DSUB9 connector on
the EA4357 devkit.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>

Enable Ethernet and add pin muxing and set the correct
frequency on the enet tx clock input.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>

Hook up the small joystick found on the EA4357 devkit.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>

The sound support consist only Headset output on the board and can be
handled by "simple-audio-card"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use mcasp1_pins as name for the pinctrl section needed for McASP1 instead
of the am335x_evm_audio_pins name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The section had two tabs instead of one.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The sound support consist only Headset output on the board and can be
handled by "simple-audio-card"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The section had two tabs instead of one.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The board uses McASP1 <-> tlv320aic3106 for analog audio and has
Headphone out and Line in connectors.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add node for McASP1 along with the needed pinctrl entries.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Analog audio is using this codec on the board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The same regulator is used by other chips on the board. The power path is:
VBAT -> TPS63031 - Enable signal is V1_8D regulator -> V3_3D.
V3_3D is used by SD slot and tlv320aic3106 codec as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GPIO5_8 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use simple card for audio support on ePOS-EVM.
The audio on the board is: McASP1 <-> tlv320aic3111 codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Analog audio is using this codec on the board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add node for McASP1 along with the needed pinctrl entries.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The VBAT and DCDC4 regulator is needed for audio support (tlv320aic3111)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GPIO2_1 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The sound support consist only Headset output on the board and can be
handled by "simple-audio-card".
Also enable the Line-In route as the board has support for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

More and more boards are moving to have audio support via simple-card.
At the same time enable options needed for most am335x and am43xx board for
audio support: McASP and TLV320AIC3X codecs.
The later two has been selected by the CONFIG_SND_AM33XX_SOC_EVM option, but
the aim is to convert all boards to use simple card.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>