Now that we have GVA page tables and an optimised TLB refill handler in
place, convert the handling of page faults in TLB mapped segment from
the guest to fill a single GVA page table entry and invalidate the TLB
entry, rather than filling a TLB entry pair directly.

Also remove the now unused kvm_mips_get_{kernel,user}_asid() functions
in mmu.c and kvm_mips_host_tlb_write() in tlb.c.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Now that we have GVA page tables and an optimised TLB refill handler in
place, convert the handling of KSeg0 page faults from the guest to fill
the GVA page tables and invalidate the TLB entry, rather than filling a
TLB entry directly.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Implement invalidation of specific pairs of GVA page table entries in
one or both of the GVA page tables. This is used when existing mappings
are replaced in the guest TLB by emulated TLBWI/TLBWR instructions. Due
to the sharing of page tables in the host kernel range, we should be
careful not to allow host pages to be invalidated.

Add a helper kvm_mips_walk_pgd() which can be used when walking of
either GPA (future patches) or GVA page tables is needed, optionally
with allocation of page tables along the way when they don't exist.

GPA page table walking will need to be protected by the kvm->mmu_lock,
so we also add a small MMU page cache in each KVM VCPU, like that found
for other architectures but smaller. This allows enough pages to be
pre-allocated to handle a single fault without holding the lock,
allowing the helper to run with the lock held without having to handle
allocation failures.

Using the same mechanism for GVA allows the same code to be used, and
allows it to use the same cache of allocated pages if the GPA walk
didn't need to allocate any new tables.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Implement invalidation of large ranges of virtual addresses from GVA
page tables in response to a guest ASID change (immediately for guest
kernel page table, lazily for guest user page table).

We iterate through a range of page tables invalidating entries and
freeing fully invalidated tables. To minimise overhead the exact ranges
invalidated depends on the flags argument to kvm_mips_flush_gva_pt(),
which also allows it to be used in future KVM_CAP_SYNC_MMU patches in
response to GPA changes, which unlike guest TLB mapping changes affects
guest KSeg0 mappings.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Refactor kvm_mips_host_tlb_inv() to also be able to invalidate any
matching TLB entry in the kernel ASID rather than assuming only the TLB
entries in the user ASID can change. Two new bool user/kernel arguments
allow the caller to indicate whether the mapping should affect each of
the ASIDs for guest user/kernel mode.

- kvm_mips_invalidate_guest_tlb() (used by TLBWI/TLBWR emulation) can
  now invalidate any corresponding TLB entry in both the kernel ASID
  (guest kernel may have accessed any guest mapping), and the user ASID
  if the entry being replaced is in guest USeg (where guest user may
  also have accessed it).

- The tlbmod fault handler (and the KSeg0 / TLB mapped / commpage fault
  handlers in later patches) can now invalidate the corresponding TLB
  entry in whichever ASID is currently active, since only a single page
  table will have been updated anyway.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

kvm_mips_host_tlb_inv() uses the TLBP instruction to probe the host TLB
for an entry matching the given guest virtual address, and determines
whether a match was found based on whether CP0_Index > 0. This is
technically incorrect as an index of 0 (with the high bit clear) is a
perfectly valid TLB index.

This is harmless at the moment due to the use of at least 1 wired TLB
entry for the KVM commpage, however we will soon be ridding ourselves of
that particular wired entry so lets fix the condition in case the entry
needing invalidation does land at TLB index 0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Use functions from the general MIPS TLB exception vector generation code
(tlbex.c) to construct a fast path TLB refill handler similar to the
general one, but cut down and capable of preserving K0 and K1.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

tlbex.c uses the implementation dependent $22 CP0 register group on
NetLogic cores, with the help of the c0_kscratch() helper. Allow these
registers to be allocated by the KVM entry code too instead of assuming
KScratch registers are all $31, which will also allow pgd_reg to be
handled since it is allocated that way.

We also drop the masking of kscratch_mask with 0xfc, as it is redundant
for the standard KScratch registers (Config4.KScrExist won't have the
low 2 bits set anyway), and apparently not necessary for NetLogic.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Activate the GVA page tables when in guest context. This will allow the
normal Linux TLB refill handler to fill from it when guest memory is
read, as well as preventing accidental reading from user memory.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Allocate GVA -> HPA page tables for guest kernel and guest user mode on
each VCPU, to allow for fast path TLB refill handling to be added later.

In the process kvm_arch_vcpu_init() needs updating to pass on any error
from the vcpu_init() callback.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Wire up a vcpu uninit implementation callback. This will be used for the
clean up of GVA->HPA page tables.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Set init_mm as the active_mm and update mm_cpumask(current->mm) to
reflect that it isn't active when in guest context. This prevents cache
management code from attempting cache flushes on host virtual addresses
while in guest context, for example due to a cache management IPIs or
later when writing of dynamically translated code hits copy on write.

We do this using helpers in static kernel code to avoid having to export
init_mm to modules.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

We only need the guest ASID loaded while in guest context, i.e. while
running guest code and while handling guest exits. We load the guest
ASID when entering the guest, however we restore the host ASID later
than necessary, when the VCPU state is saved i.e. vcpu_put() or slightly
earlier if preempted after returning to the host.

This mismatch is both unpleasant and causes redundant host ASID restores
in kvm_trap_emul_vcpu_put(). Lets explicitly restore the host ASID when
returning to the host, and don't bother restoring the host ASID on
context switch in unless we're already in guest context.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Add implementation callbacks for entering the guest (vcpu_run()) and
reentering the guest (vcpu_reenter()), allowing implementation specific
operations to be performed before entering the guest or after returning
to the host without cluttering kvm_arch_vcpu_ioctl_run().

This allows the T&E specific lazy user GVA flush to be moved into
trap_emul.c, along with disabling of the HTW. We also move
kvm_mips_deliver_interrupts() as VZ will need to restore the guest timer
state prior to delivering interrupts.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

The kvm_vcpu_arch structure contains both mm_structs for allocating MMU
contexts (primarily the ASID) but it also copies the resulting ASIDs
into guest_{user,kernel}_asid[] arrays which are referenced from uasm
generated code.

This duplication doesn't seem to serve any purpose, and it gets in the
way of generalising the ASID handling across guest kernel/user modes, so
lets just extract the ASID straight out of the mm_struct on demand, and
in fact there are convenient cpu_context() and cpu_asid() macros for
doing so.

To reduce the verbosity of this code we do also add kern_mm and user_mm
local variables where the kernel and user mm_structs are used.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

The MIPS KVM host and guest GVA ASIDs may need regenerating when
scheduling a process in guest context, which is done from the
kvm_arch_vcpu_load() / kvm_arch_vcpu_put() functions in mmu.c.

However this is a fairly implementation specific detail. VZ for example
may use GuestIDs instead of normal ASIDs to distinguish mappings
belonging to different guests, and even on VZ without GuestID the root
TLB will be used differently to trap & emulate.

Trap & emulate GVA ASIDs only relate to the user part of the full
address space, so can be left active during guest exit handling (guest
context) to allow guest instructions to be easily read and translated.

VZ root ASIDs however are for GPA mappings so can't be left active
during normal kernel code. They also aren't useful for accessing guest
virtual memory, and we should have CP0_BadInstr[P] registers available
to provide encodings of trapping guest instructions anyway.

Therefore move the ASID preemption handling into the implementation
callback.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Convert the get_regs() and set_regs() callbacks to vcpu_load() and
vcpu_put(), which provide a cpu argument and more closely match the
kvm_arch_vcpu_load() / kvm_arch_vcpu_put() that they are called by.

This is in preparation for moving ASID management into the
implementations.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

KVM T&E uses an ASID for guest kernel mode and an ASID for guest user
mode. The current ASID is saved when the guest is scheduled out, and
restored when scheduling back in, with checks for whether the ASID needs
to be regenerated.

This isn't really necessary as the ASID can be easily determined by the
current guest mode, so lets simplify it to just read the required ASID
from guest_kernel_asid or guest_user_asid even if the ASID hasn't been
regenerated.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

MIPS incompletely implements the KVM_NMI ioctl to supposedly perform a
CPU reset, but all it actually does is invalidate the ASIDs. It doesn't
expose the KVM_CAP_USER_NMI capability which is supposed to indicate the
presence of the KVM_NMI ioctl, and no user software actually uses it on
MIPS.

Since this is dead code that would technically need updating for GVA
page table handling in upcoming patches, remove it now. If we wanted to
implement NMI injection later it can always be done properly along with
the KVM_CAP_USER_NMI capability, and if we wanted to implement a proper
CPU reset it would be better done with a separate ioctl.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Merge in MIPS prerequisites from GVA page tables and GPA page tables
series. The same branch can also merge into the MIPS tree.
Signed-off-by: James Hogan <james.hogan@imgtec.com>

The protected cache ops contain no out of line fixup code to return an
error code in the event of a fault, with the cache op being skipped in
that case. For KVM however we'd like to detect this case as page
faulting will be disabled so it could happen during normal operation if
the GVA page tables were flushed, and need to be handled by the caller.

Add the out-of-line fixup code to load the error value -EFAULT into the
return variable, and adapt the protected cache line functions to pass
the error back to the caller.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Export to TLB exception code generating functions so that KVM can
construct a fast TLB refill handler for guest context without
reinventing the wheel quite so much.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Add include guards in asm/uasm.h to allow it to be safely used by a new
header asm/tlbex.h in the next patch to expose TLB exception building
functions for KVM to use.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Export pmd_init(), invalid_pmd_table and tlbmiss_handler_setup_pgd to
GPL kernel modules so that MIPS KVM can use the inline page table
management functions and switch between page tables:

- pmd_init() will be used directly by KVM to initialise newly allocated
  pmd tables with invalid lower level table pointers.

- invalid_pmd_table is used by pud_present(), pud_none(), and
  pud_clear(), which KVM will use to test and clear pud entries.

- tlbmiss_handler_setup_pgd() will be called by KVM entry code to switch
  to the appropriate GVA page tables.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

pgd_alloc() references init_mm which is not exported to modules. In
order for KVM to be able to use pgd_alloc() to allocate GVA page tables,
move pgd_alloc() into a new pgtable.c file and export it to modules.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

* Return directly after a call of the function "copy_from_user" failed
  in a case block.

* Delete the jump label "out" which became unnecessary with
  this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>

This reverts commit bc613494.

A CPUID instruction executed in VMX non-root mode always causes a
VM-exit, regardless of the leaf being queried.

Fixes: bc613494 ("KVM: nested VMX: disable perf cpuid reporting")
Signed-off-by: Jim Mattson <jmattson@google.com>
[The issue solved by bc613494 has been resolved with ff651cb6
 ("KVM: nVMX: Add nested msr load/restore algorithm").]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

Vector population count instructions for dwords and qwords are to be
used in future Intel Xeon & Xeon Phi processors. The bit 14 of
CPUID[level:0x07, ECX] indicates that the new instructions are
supported by a processor.

The spec can be found in the Intel Software Developer Manual (SDM)
or in the Instruction Set Extensions Programming Reference (ISE).
Signed-off-by: Piotr Luc <piotr.luc@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

For AVX512_VPOPCNTDQ.

Vector population count instructions for dwords and qwords are going to be
available in future Intel Xeon & Xeon Phi processors. Bit 14 of
CPUID[level:0x07, ECX] indicates that the instructions are supported by a
processor.

The specification can be found in the Intel Software Developer Manual (SDM)
and in the Instruction Set Extensions Programming Reference (ISE).

Populate the feature bit and clear it when xsave is disabled.
Signed-off-by: Piotr Luc <piotr.luc@intel.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Cc: Radim Krčmář <rkrcmar@redhat.com>
Link: http://lkml.kernel.org/r/20170110173403.6010-2-piotr.luc@intel.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull namespace fixes from Eric Biederman:
 "This tree contains 4 fixes.

  The first is a fix for a race that can causes oopses under the right
  circumstances, and that someone just recently encountered.

  Past that are several small trivial correct fixes. A real issue that
  was blocking development of an out of tree driver, but does not appear
  to have caused any actual problems for in-tree code. A potential
  deadlock that was reported by lockdep. And a deadlock people have
  experienced and took the time to track down caused by a cleanup that
  removed the code to drop a reference count"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  sysctl: Drop reference added by grab_header in proc_sys_readdir
  pid: fix lockdep deadlock warning due to ucount_lock
  libfs: Modify mount_pseudo_xattr to be clear it is not a userspace mount
  mnt: Protect the mountpoint hashtable with mount_lock

Pull char/misc driver fixes from Greg KH:
 "Here are some small char/misc driver fixes for 4.10-rc4 that resolve
  some reported issues.

  The MEI driver issue resolves a lot of problems that people have been
  having, as does the mem driver fix. The other minor fixes resolve
  other reported issues.

  All of these have been in linux-next for a while"

* tag 'char-misc-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  vme: Fix wrong pointer utilization in ca91cx42_slave_get
  auxdisplay: fix new ht16k33 build errors
  ppdev: don't print a free'd string
  extcon: return error code on failure
  drivers: char: mem: Fix thinkos in kmem address checks
  mei: bus: enable OS version only for SPT and newer

Merge tag 'driver-core-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fix from Greg KH:
 "Here is a single patch being reverted to remove a feature that was
  added in 4.10-rc1 that isn't quite ready for release.

  It will be redone as a debugfs file instead of a sysfs file in the
  future"

* tag 'driver-core-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  Revert "driver core: Add deferred_probe attribute to devices in sysfs"

Pull tty/serial fixes from Greg KH:
 "Here are some small tty/serial driver fixes for 4.10-rc4 to resolve a
  number of reported issues.

  Nothing major here at all, one revert of a problematic patch, and some
  other tiny bugfixes. Full details are in the shortlog below.

  All have been in linux-next with no reported issues"

* tag 'tty-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  sysrq: attach sysrq handler correctly for 32-bit kernel
  Revert "tty: serial: 8250: add CON_CONSDEV to flags"
  Clearing FIFOs in RS485 emulation mode causes subsequent transmits to break
  8250_pci: Fix potential use-after-free in error path
  tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done
  tty/serial: atmel_serial: BUG: stop DMA from transmitting in stop_tx

Pull USB fixes from Greg KH:
 "Here are a few small USB driver fixes for 4.10-rc4 to resolve some
  reported issues.

  The "largest" here is a number of bugs being fixed in the ch341
  usb-serial driver, to hopefully resolve the mess of different devices
  floating around that use this driver that have been having problems
  with the 4.10-rc1 release.

  There's also a tiny musb fix that I missed in the last pull request,
  as well as the traditional xhci fix rounding out the batch.

  All have been in linux-next with no reported issues"

* tag 'usb-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  xhci: fix deadlock at host remove by running watchdog correctly
  USB: serial: ch341: fix control-message error handling
  usb: musb: fix runtime PM in debugfs
  wusbcore: Fix one more crypto-on-the-stack bug
  USB: serial: kl5kusb105: fix line-state error handling
  USB: serial: ch341: fix baud rate and line-control handling
  USB: serial: ch341: fix line settings after reset-resume
  USB: serial: ch341: fix resume after reset
  USB: serial: ch341: fix open error handling
  USB: serial: ch341: fix modem-control and B0 handling
  USB: serial: ch341: fix open and resume after B0
  USB: serial: ch341: fix initial modem-control state

Pull i2c fixes from Wolfram Sang:
 "Bugfixes for I2C. Mostly core this time which is a bit unusual but
  nothing really scary in there"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: piix4: Avoid race conditions with IMC
  i2c: fix spelling mistake: "insufficent" -> "insufficient"
  i2c: print correct device invalid address
  i2c: do not enable fall back to Host Notify by default
  i2c: fix kernel memory disclosure in dev interface

Pull x86 fixes from Ingo Molnar:
 "Misc fixes:

   - unwinder fixes
   - AMD CPU topology enumeration fixes
   - microcode loader fixes
   - x86 embedded platform fixes
   - fix for a bootup crash that may trigger when clearcpuid= is used
     with invalid values"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mpx: Use compatible types in comparison to fix sparse error
  x86/tsc: Add the Intel Denverton Processor to native_calibrate_tsc()
  x86/entry: Fix the end of the stack for newly forked tasks
  x86/unwind: Include __schedule() in stack traces
  x86/unwind: Disable KASAN checks for non-current tasks
  x86/unwind: Silence warnings for non-current tasks
  x86/microcode/intel: Use correct buffer size for saving microcode data
  x86/microcode/intel: Fix allocation size of struct ucode_patch
  x86/microcode/intel: Add a helper which gives the microcode revision
  x86/microcode: Use native CPUID to tickle out microcode revision
  x86/CPU: Add native CPUID variants returning a single datum
  x86/boot: Add missing declaration of string functions
  x86/CPU/AMD: Fix Bulldozer topology
  x86/platform/intel-mid: Rename 'spidev' to 'mrfld_spidev'
  x86/cpu: Fix typo in the comment for Anniedale
  x86/cpu: Fix bootup crashes by sanitizing the argument of the 'clearcpuid=' command-line option

Pull NOHZ fix from Ingo Molnar:
 "This fixes an old NOHZ race where we incorrectly calculate the next
  timer interrupt in certain circumstances where hrtimers are pending,
  that can cause hard to reproduce stalled-values artifacts in
  /proc/stat"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  nohz: Fix collision between tick and other hrtimers

Pull perf fixes from Ingo Molnar:
 "Misc race fixes uncovered by fuzzing efforts, a Sparse fix, two PMU
  driver fixes, plus miscellanous tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86: Reject non sampling events with precise_ip
  perf/x86/intel: Account interrupts for PEBS errors
  perf/core: Fix concurrent sys_perf_event_open() vs. 'move_group' race
  perf/core: Fix sys_perf_event_open() vs. hotplug
  perf/x86/intel: Use ULL constant to prevent undefined shift behaviour
  perf/x86/intel/uncore: Fix hardcoded socket 0 assumption in the Haswell init code
  perf/x86: Set pmu->module in Intel PMU modules
  perf probe: Fix to probe on gcc generated symbols for offline kernel
  perf probe: Fix --funcs to show correct symbols for offline module
  perf symbols: Robustify reading of build-id from sysfs
  perf tools: Install tools/lib/traceevent plugins with install-bin
  tools lib traceevent: Fix prev/next_prio for deadline tasks
  perf record: Fix --switch-output documentation and comment
  perf record: Make __record_options static
  tools lib subcmd: Add OPT_STRING_OPTARG_SET option
  perf probe: Fix to get correct modname from elf header
  samples/bpf trace_output_user: Remove duplicate sys/ioctl.h include
  samples/bpf sock_example: Avoid getting ethhdr from two includes
  perf sched timehist: Show total scheduling time