Several pinconf parameters have a fairly straight-forward mapping onto
the Aspeed pin controller. These include management of pull-down bias,
drive-strength, and some debounce configuration.

Pin biasing largely is managed on a per-GPIO-bank basis, aside from the
ADC and RMII/RGMII pins. As the bias configuration for each pin in a
bank maps onto a single per-bank bit, configuration tables will be
introduced to describe the ranges of pins and the supported pinconf
parameter. The use of tables also helps with the sparse support of
pinconf properties, and the fact that not all GPIO banks support
biasing or drive-strength configuration.

Further, as the pin controller uses a consistent approach for bias and
drive strength configuration at the register level, a second table is
defined for looking up the the bit-state required to enable or query the
provided configuration.

Testing for pinctrl-aspeed-g4 was performed on an OpenPOWER Palmetto
system, and pinctrl-aspeed-g5 on an AST2500EVB as well as under QEMU.
The test method was to set the appropriate bits via devmem and verify
the result through the controller's pinconf-pins debugfs file. This
simultaneously validates the get() path and half of the set() path. The
remainder of the set() path was validated by configuring a handful of
pins via the devicetree with the supported pinconf properties and
verifying the appropriate registers were touched.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add new compatible for stm32f469 MCU.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch which adds STM32F469 pinctrl and GPIO support, relies on the
generic STM32 pinctrl driver.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Remove "ngpios" bindings definition as it is no more used in stm32 pinctrl
driver.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pinctrl has to be registered earlier. Mainly to register bank irqdomain
earlier as other devices could use interrupts from those irqdomain.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use device tree entries to declare gpio range. It will allow to use
no contiguous gpio bank and holes inside a bank.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIO management is pretty simple and is part of the same IP than the pin
controller for the Armada 37xx SoCs.  This patch adds the GPIO support to
the pinctrl-armada-37xx.c file, it also allows sharing common functions
between the gpiolib and the pinctrl drivers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Armada 37xx SoC come with 2 pin controllers: one on the south
bridge (managing 28 pins) and one on the north bridge (managing 36 pins).

At the hardware level the controller configure the pins by group and not
pin by pin. This constraint is reflected in the design of the driver:
only the group related functions are implemented.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Document the device tree binding for the pin controllers found on the
Armada 37xx SoCs.

Update the binding documention of the xtal clk which is a subnode of this
syscon node.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
[Fixed gpios node]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl_init_controller() is not used outside core.c, thus make it
static and prevent compiler to warn.

drivers/pinctrl/core.c:1943:21: warning: no previous prototype for ‘pinctrl_init_controller’ [-Wmissing-prototypes]
 struct pinctrl_dev *pinctrl_init_controller(struct pinctrl_desc *pctldesc,
                     ^~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add bi-directional and output-enable pin configuration properties.

bi-directional allows to specify when a pin shall operate in input and
output mode at the same time. This is particularly useful in platforms
where input and output buffers have to be manually enabled.

output-enable is just syntactic sugar to specify that a pin shall
operate in output mode, ignoring the provided argument.
This pairs with input-enable pin configuration option.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Three video input signals suffered from a search/replace failure in
some copied code.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'samsung-pinctrl-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel

Samsung pinctrl drivers update for v4.12:
1. Add support for pad retention control through pinctrl drivers which
   moves us forward to better runtime PM of pinctrl, clocks, power domains
   and other devices.
2. Fix GPIO hogs by registering pinctrl before registering gpiolib.
3. Use devm-like interface.

When suspending to RAM, the power to the core is cut and the register
values are lost. Save and restore more registers than just IMR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Document "pinmux" property as part of generic pin controller
documentation.
Fix 2 minor typos in documentation while at there.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Correct the incorrect function name and description.

Fixes: a76edc89 ("pinctrl: core: Add generic pinctrl functions for managing groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add pinctrl driver support for the Axis ARTPEC-6 SoC.
There are only some pins that actually have different
functions available, but all can control bias (pull-up/-down)
and drive strength.

Code originally written by Chris Paterson.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add the bindings for the pinmux functions in the
ARTPEC-6 SoC, including bias and drive strength.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The NAND DQS pins are currently named nand_dqs_0 and nand_dqs_1.
However, they both seem to have the same function, just exposed on
different pins (unlike the ethernet TX pins for example, where there's
eth_txd0..3 - all of these can be active at the same time as they are
different data lines).
Rename the NAND DQS pins to nand_dqs_15 and nand_dqs_18 to reflect that
it's the same functionality just exposed on different pins (BOOT_15 and
BOOT_18).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The nand_groups table uses different names for the NAND DQS pins than
the GROUP() definition in meson8b_cbus_groups (nand_dqs_0 vs nand_dqs0).
This prevents using the NAND DQS pins in the devicetree.

Fix this by ensuring that the GROUP() definition and the
meson8b_cbus_groups use the same name for these pins.

Fixes: 0fefcb68 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'sh-pfc-for-v4.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v4.12 (take two)

  - Add basic support for the Pin Function Controller on revision ES2.0
    of the R-Car H3 SoC, which differs from ES1.x in many ways.

Add pins, groups, and a function for SCIF_CLK on R-Car H3 ES2.0.
SCIF_CLK is the external clock source for the Baud Rate Generator for
External Clock (BRG) on (H)SCIF serial ports.

Extracted from a big patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>

Add pins, groups, and functions for all SCIF serial ports on R-Car H3
ES2.0.

Extracted from a big patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>

The Pin Function Controller module in the R-Car H3 ES2.0 differs from
ES1.x in many ways.

The goal is twofold:
  1. Support both the ES1.x and ES2.0 SoC revisions in a single binary
     for now,
  2. Make it clear which code supports ES1.x, so it can easily be
     identified and removed later, when production SoCs are deemed
     ubiquitous.

Hence this patch:
  1. Extracts the support for R-Car H3 ES1.x into a separate file, as
     the differences are quite large,
  2. Adds code for detecting the SoC revision at runtime using the new
     soc_device_match() API, and selecting pinctrl tables for the actual
     SoC revision,
  3. Replaces the core register and bitfield definitions by their
     counterparts for R-Car H3 ES2.0.

The addition of pins, groups, and functions for the various on-chip
devices is left to subsequent patches.

The R-Car H3 ES2.0 register and bitfield definitions were extracted from
a patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When trying to add a gpio-hog, we enter a weird loop where the gpio-ranges
is needed when gpiochip_add_data() is called but in the current implementation
the ranges are added from the driver afterwards.

A simple solution is to rely on the DR gpio-ranges attribute and remove the
call to gpiochip_add_pin_range().
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add a Git tree on @kernel.org for maintaining the Samsung pinctrl
drivers.  The tree will be maintained in a shared model between current
Samsung pinctrl maintainers.  Pull requests will be going to Linus
Walleij.

Also add the patchwork for linux-samsung-soc mailing list which will be
used for handling the patches.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix some inverted bit numbers in some pinctrl groups and add missing pins
and groups to be in pair with the GXBB pinctrl pins definition.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

With real-time preemption, regmap functions cannot be used in the
implementation of irq_chip since they use spinlocks which may sleep.

Move the setting of the mux for IRQs to an irq_bus_sync_unlock handler
where we are allowed to sleep.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We need to avoid calling regmap functions from irq handlers, so the next
commit is going to move the call to rockchip_set_mux() into an
irq_bus_sync_unlock handler.  But we can't return an error from there so
we still need to check the settings from rockchip_irq_set_type() and we
will use this new rockchip_verify_mux() function from there.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This lock is used from rockchip_irq_set_type() which is part of the
irq_chip implementation and thus must use raw_spinlock_t as documented
in Documentation/gpio/driver.txt.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

regmap_update_bits does its own locking and everything else accessed
here is a local variable so there is no need to lock around it.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'sh-pfc-for-v4.12-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v4.12

  - Fixes and cleanups.

Use devm_gpiochip_add_data to simplify the error path in
samsung_gpiolib_register.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

If we request a GPIO hog, then gpiochip_add_data will attempt
to request some of its own GPIOs. The driver also uses
gpiochip_generic_request which means that for any GPIO request to
succeed the pinctrl needs to be registered. Currently however the
driver registers the GPIO and then the pinctrl meaning all GPIO hog
requests will fail, which then in turn causes the whole driver to fail
probe.

Fix this up by ensuring we register the pinctrl first. This
does require us to manually set the GPIO base for the
pinctrl. Fortunately the driver already assigns a fixed GPIO base, in
samsung_gpiolib_register, and uses the same calculation it does for
the pin_base. Meaning the two will always be the same and allowing us
to reuse the pinbase and avoid the issue.

Although currently there are no users of GPIO hogs in mainline
there are plenty of Samsung based boards that are widely used for
development purposes of other hardware. Indeed we hit this issue
whilst attaching some additional hardware to an Arndale system.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

This patch adds support for retention control for Exynos5433 SoCs. Three
groups of pins has been defined for retention control: common shared group
for ALIVE, CPIF, eSE, FINGER, IMEM, NFC, PERIC, TOUCH pin banks and
separate control for FSYS and AUD pin banks, for which PMU retention
registers match whole banks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>