If cable is attached after probe sequence, the usbnet framework would
not automatically start processing RX packets except at least one
packet was transmitted.

On systems with any kind of address auto configuration this issue was
not detected, because some packets are send immediately after link state
is changed to "running".

With this patch we will notify usbnet about link status change provided by the
PHYlib.

Fixes: e532a096 ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/r/20220624075139.3139300-1-o.rempel@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Mails to Charles get an auto reply, that he is no longer working at
Eff'Innov technologies. Drop the entry and mark the driver as orphaned.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220626200039.4062784-1-michael@walle.ccSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This should be bitwise operator not logical.

Fixes: 862cd659 ("octeon_ep: Add driver framework and device initialization")
Signed-off-by: Shreenidhi Shedi <sshedi@vmware.com>
Link: https://lore.kernel.org/r/20220626132947.3992423-1-sshedi@vmware.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Victor Nogueira says:

====================
Notify user space if any actions were flushed before error

This patch series fixes the behaviour of actions flush so that the
kernel always notifies user space whenever it deletes actions during a
flush operation, even if it didn't flush all the actions. This series
also introduces tdc tests to verify this new behaviour.
====================

Link: https://lore.kernel.org/r/20220623140742.684043-1-victor@mojatatu.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add tdc test cases to verify new flush behaviour is correct, which do
the following:

- Try to flush only one action which is being referenced by a filter
- Try to flush three actions where the last one (index 3) is being
  referenced by a filter
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If during an action flush operation one of the actions is still being
referenced, the flush operation is aborted and the kernel returns to
user space with an error. However, if the kernel was able to flush, for
example, 3 actions and failed on the fourth, the kernel will not notify
user space that it deleted 3 actions before failing.

This patch fixes that behaviour by notifying user space of how many
actions were deleted before flush failed and by setting extack with a
message describing what happened.

Fixes: 55334a5d ("net_sched: act: refuse to remove bound action outside")
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

epic_close() calls epic_rx() and uses dma buffer, but in epic_remove_one()
we already freed the dma buffer. To fix this issue, reorder function calls
like in the .probe function.

BUG: KASAN: use-after-free in epic_rx+0xa6/0x7e0 [epic100]
Call Trace:
 epic_rx+0xa6/0x7e0 [epic100]
 epic_close+0xec/0x2f0 [epic100]
 unregister_netdev+0x18/0x20
 epic_remove_one+0xaa/0xf0 [epic100]

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Reported-by: Yilun Wu <yiluwu@cs.stonybrook.edu>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Reviewed-by: Francois Romieu <romieu@fr.zoreil.com>
Link: https://lore.kernel.org/r/20220627043351.25615-1-ztong0001@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

While looking at a syzbot report I noticed the NAPI only gets
disabled before it's deleted. I think that user can detach
the queue before destroying the device and the NAPI will never
be stopped.

Fixes: 94317099 ("tun: enable NAPI for TUN/TAP driver")
Acked-by: Petar Penkov <ppenkov@aviatrix.com>
Link: https://lore.kernel.org/r/20220623042105.2274812-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Shuang Li reported a NULL pointer dereference crash:

  [] BUG: kernel NULL pointer dereference, address: 0000000000000068
  [] RIP: 0010:tipc_link_is_up+0x5/0x10 [tipc]
  [] Call Trace:
  []  <IRQ>
  []  tipc_bcast_rcv+0xa2/0x190 [tipc]
  []  tipc_node_bc_rcv+0x8b/0x200 [tipc]
  []  tipc_rcv+0x3af/0x5b0 [tipc]
  []  tipc_udp_recv+0xc7/0x1e0 [tipc]

It was caused by the 'l' passed into tipc_bcast_rcv() is NULL. When it
creates a node in tipc_node_check_dest(), after inserting the new node
into hashtable in tipc_node_create(), it creates the bc link. However,
there is a gap between this insert and bc link creation, a bc packet
may come in and get the node from the hashtable then try to dereference
its bc link, which is NULL.

This patch is to fix it by moving the bc link creation before inserting
into the hashtable.

Note that for a preliminary node becoming "real", the bc link creation
should also be called before it's rehashed, as we don't create it for
preliminary nodes.

Fixes: 4cbf8ac2 ("tipc: enable creating a "preliminary" node")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently added debug in commit f9aefd6b ("net: warn if mac header
was not set") caught a bug in skb_tunnel_check_pmtu(), as shown
in this syzbot report [1].

In ndo_start_xmit() paths, there is really no need to use skb->mac_header,
because skb->data is supposed to point at it.

[1] WARNING: CPU: 1 PID: 8604 at include/linux/skbuff.h:2784 skb_mac_header_len include/linux/skbuff.h:2784 [inline]
WARNING: CPU: 1 PID: 8604 at include/linux/skbuff.h:2784 skb_tunnel_check_pmtu+0x5de/0x2f90 net/ipv4/ip_tunnel_core.c:413
Modules linked in:
CPU: 1 PID: 8604 Comm: syz-executor.3 Not tainted 5.19.0-rc2-syzkaller-00443-g8720bd95 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:skb_mac_header_len include/linux/skbuff.h:2784 [inline]
RIP: 0010:skb_tunnel_check_pmtu+0x5de/0x2f90 net/ipv4/ip_tunnel_core.c:413
Code: 00 00 00 00 fc ff df 4c 89 fa 48 c1 ea 03 80 3c 02 00 0f 84 b9 fe ff ff 4c 89 ff e8 7c 0f d7 f9 e9 ac fe ff ff e8 c2 13 8a f9 <0f> 0b e9 28 fc ff ff e8 b6 13 8a f9 48 8b 54 24 70 48 b8 00 00 00
RSP: 0018:ffffc90002e4f520 EFLAGS: 00010212
RAX: 0000000000000324 RBX: ffff88804d5fd500 RCX: ffffc90005b52000
RDX: 0000000000040000 RSI: ffffffff87f05e3e RDI: 0000000000000003
RBP: ffffc90002e4f650 R08: 0000000000000003 R09: 000000000000ffff
R10: 000000000000ffff R11: 0000000000000000 R12: 000000000000ffff
R13: 0000000000000000 R14: 000000000000ffcd R15: 000000000000001f
FS: 00007f3babba9700(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000080 CR3: 0000000075319000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
geneve_xmit_skb drivers/net/geneve.c:927 [inline]
geneve_xmit+0xcf8/0x35d0 drivers/net/geneve.c:1107
__netdev_start_xmit include/linux/netdevice.h:4805 [inline]
netdev_start_xmit include/linux/netdevice.h:4819 [inline]
__dev_direct_xmit+0x500/0x730 net/core/dev.c:4309
dev_direct_xmit include/linux/netdevice.h:3007 [inline]
packet_direct_xmit+0x1b8/0x2c0 net/packet/af_packet.c:282
packet_snd net/packet/af_packet.c:3073 [inline]
packet_sendmsg+0x21f4/0x55d0 net/packet/af_packet.c:3104
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:734
____sys_sendmsg+0x6eb/0x810 net/socket.c:2489
___sys_sendmsg+0xf3/0x170 net/socket.c:2543
__sys_sendmsg net/socket.c:2572 [inline]
__do_sys_sendmsg net/socket.c:2581 [inline]
__se_sys_sendmsg net/socket.c:2579 [inline]
__x64_sys_sendmsg+0x132/0x220 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f3baaa89109
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f3babba9168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f3baab9bf60 RCX: 00007f3baaa89109
RDX: 0000000000000000 RSI: 0000000020000a00 RDI: 0000000000000003
RBP: 00007f3baaae305d R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffe74f2543f R14: 00007f3babba9300 R15: 0000000000022000
</TASK>

Fixes: 4cb47a86 ("tunnels: PMTU discovery support for directly bridged IP packets")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "1<<31" shift has a sign extension bug so IFF_TX_SKB_NO_LINEAR is
0xffffffff80000000 instead of 0x0000000080000000.

Fixes: c2ff53d8 ("net: Add priv_flags for allow tx skb without linear")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://lore.kernel.org/r/YrRrcGttfEVnf85Q@kiliSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Enguerrand de Ribaucourt says:

====================
net: dp83822: fix interrupt floods

The false carrier and RX error counters, once half full, produce interrupt
floods. Since we do not use these counters, these interrupts should be disabled.
====================

Link: https://lore.kernel.org/r/20220623134645.1858361-1-enguerrand.de-ribaucourt@savoirfairelinux.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Some RX errors, notably when disconnecting the cable, increase the RCSR
register. Once half full (0x7fff), an interrupt flood is generated. I
measured ~3k/s interrupts even after the RX errors transfer was
stopped.

Since we don't read and clear the RCSR register, we should disable this
interrupt.

Fixes: 87461f7a ("net: phy: DP83822 initial driver submission")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When unplugging an Ethernet cable, false carrier events were produced by
the PHY at a very high rate. Once the false carrier counter full, an
interrupt was triggered every few clock cycles until the cable was
replugged. This resulted in approximately 10k/s interrupts.

Since the false carrier counter (FCSCR) is never used, we can safely
disable this interrupt.

In addition to improving performance, this also solved MDIO read
timeouts I was randomly encountering with an i.MX8 fec MAC because of
the interrupt flood. The interrupt count and MDIO timeout fix were
tested on a v5.4.110 kernel.

Fixes: 87461f7a ("net: phy: DP83822 initial driver submission")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Syzbot found a race between tun file and device destruction.
NAPIs live in struct tun_file which can get destroyed before
the netdev so we have to del them explicitly. The current
code is missing deleting the NAPI if the queue was detached
first.

Fixes: 94317099 ("tun: enable NAPI for TUN/TAP driver")
Reported-by: syzbot+b75c138e9286ac742647@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20220623042039.2274708-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When the third packet of 3WHS connection establishment
contains payload, it is added into socket receive queue
without the XFRM check and the drop of connection tracking
context.

This means that if the data is left unread in the socket
receive queue, conntrack module can not be unloaded.

As most applications usually reads the incoming data
immediately after accept(), bug has been hiding for
quite a long time.

Commit 68822bdf ("net: generalize skb freeing
deferral to per-cpu lists") exposed this bug because
even if the application reads this data, the skb
with nfct state could stay in a per-cpu cache for
an arbitrary time, if said cpu no longer process RX softirqs.

Many thanks to Ilya Maximets for reporting this issue,
and for testing various patches:
https://lore.kernel.org/netdev/20220619003919.394622-1-i.maximets@ovn.org/

Note that I also added a missing xfrm4_policy_check() call,
although this is probably not a big issue, as the SYN
packet should have been dropped earlier.

Fixes: b59c2701 ("[NETFILTER]: Keep conntrack reference until IPsec policy checks are done")
Reported-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Tested-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Ilya Maximets <i.maximets@ovn.org>
Link: https://lore.kernel.org/r/20220623050436.1290307-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Cover the scenario when we cannot insert a socket into the sockmap, because
it has it is using ULP. Failed insert should not have any effect on the ULP
state. This is a regression test.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/r/20220623091231.417138-1-jakub@cloudflare.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

udpgso_bench.sh has been running its IPv6 TCP test with IPv4 arguments
since its initial conmit. Looks like a typo.

Fixes: 3a687bef ("selftests: udp gso benchmark")
Cc: willemb@google.com
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20220623000234.61774-1-dmichail@fungible.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

syzbot reported uninit-value in tcp_recvmsg() [1]

Issue here is that msg->msg_get_inq should have been cleared,
otherwise tcp_recvmsg() might read garbage and perform
more work than needed, or have undefined behavior.

Given CONFIG_INIT_STACK_ALL_ZERO=y is probably going to be
the default soon, I chose to change __sys_recvfrom() to clear
all fields but msghdr.addr which might be not NULL.

For __copy_msghdr_from_user(), I added an explicit clear
of kmsg->msg_get_inq.

[1]
BUG: KMSAN: uninit-value in tcp_recvmsg+0x6cf/0xb60 net/ipv4/tcp.c:2557
tcp_recvmsg+0x6cf/0xb60 net/ipv4/tcp.c:2557
inet_recvmsg+0x13a/0x5a0 net/ipv4/af_inet.c:850
sock_recvmsg_nosec net/socket.c:995 [inline]
sock_recvmsg net/socket.c:1013 [inline]
__sys_recvfrom+0x696/0x900 net/socket.c:2176
__do_sys_recvfrom net/socket.c:2194 [inline]
__se_sys_recvfrom net/socket.c:2190 [inline]
__x64_sys_recvfrom+0x122/0x1c0 net/socket.c:2190
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x46/0xb0

Local variable msg created at:
__sys_recvfrom+0x81/0x900 net/socket.c:2154
__do_sys_recvfrom net/socket.c:2194 [inline]
__se_sys_recvfrom net/socket.c:2190 [inline]
__x64_sys_recvfrom+0x122/0x1c0 net/socket.c:2190

CPU: 0 PID: 3493 Comm: syz-executor170 Not tainted 5.19.0-rc3-syzkaller-30868-g4b28366af7d9 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: f94fd25c ("tcp: pass back data left in socket after receive")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Alexander Potapenko<glider@google.com>
Link: https://lore.kernel.org/r/20220622150220.1091182-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

"mlx" Devicetree vendor prefix is not documented and instead "mellanox"
should be used.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220622115416.7400-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The pause settings reported by the PHY should also be applied to the GMII port
status override otherwise the switch will not generate pause frames towards the
link partner despite the advertisement saying otherwise.

Fixes: 246d7f77 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220623030204.1966851-1-f.fainelli@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

of_find_node_by_name() will decrease the refcount of its first arg and
we need a of_node_get() to keep refcount balance.

Fixes: 7d9ee2e8 ("net: dsa: hellcreek: Add PTP status LEDs")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220622040621.4094304-1-windhl@126.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Paolo Abeni:
 "Including fixes from bpf and netfilter.

  Current release - regressions:

   - netfilter: cttimeout: fix slab-out-of-bounds read in
     cttimeout_net_exit

Current release - new code bugs:

   - bpf: ftrace: keep address offset in ftrace_lookup_symbols

   - bpf: force cookies array to follow symbols sorting

  Previous releases - regressions:

   - ipv4: ping: fix bind address validity check

   - tipc: fix use-after-free read in tipc_named_reinit

   - eth: veth: add updating of trans_start

  Previous releases - always broken:

   - sock: redo the psock vs ULP protection check

   - netfilter: nf_dup_netdev: fix skb_under_panic

   - bpf: fix request_sock leak in sk lookup helpers

   - eth: igb: fix a use-after-free issue in igb_clean_tx_ring

   - eth: ice: prohibit improper channel config for DCB

   - eth: at803x: fix null pointer dereference on AR9331 phy

   - eth: virtio_net: fix xdp_rxq_info bug after suspend/resume

  Misc:

   - eth: hinic: replace memcpy() with direct assignment"

* tag 'net-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
  net: openvswitch: fix parsing of nw_proto for IPv6 fragments
  sock: redo the psock vs ULP protection check
  Revert "net/tls: fix tls_sk_proto_close executed repeatedly"
  virtio_net: fix xdp_rxq_info bug after suspend/resume
  igb: Make DMA faster when CPU is active on the PCIe link
  net: dsa: qca8k: reduce mgmt ethernet timeout
  net: dsa: qca8k: reset cpu port on MTU change
  MAINTAINERS: Add a maintainer for OCP Time Card
  hinic: Replace memcpy() with direct assignment
  Revert "drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c"
  net: phy: smsc: Disable Energy Detect Power-Down in interrupt mode
  ice: ethtool: Prohibit improper channel config for DCB
  ice: ethtool: advertise 1000M speeds properly
  ice: Fix switchdev rules book keeping
  ice: ignore protocol field in GTP offload
  netfilter: nf_dup_netdev: add and use recursion counter
  netfilter: nf_dup_netdev: do not push mac header a second time
  selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh
  net/tls: fix tls_sk_proto_close executed repeatedly
  erspan: do not assume transport header is always set
  ...

Pull MMC fixes from Ulf Hansson:

 - mtk-sd: Fix dma hang issues

 - sdhci-pci-o2micro: Fix card detect by dealing with debouncing

* tag 'mmc-v5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: mediatek: wait dma stop bit reset to 0
  mmc: sdhci-pci-o2micro: Fix card detect by dealing with debouncing

Pull sound fixes from Takashi Iwai:
 "All small changes, mostly device-specific:

   - A regression fix for PCM WC-page allocation on x86

   - A regression fix for i915 audio component binding

   - Fixes for (longstanding) beep handling bug

   - Runtime PM fixes for Intel LPE HDMI audio

   - A couple of pending FireWire fixes

   - Usual HD-audio and USB-audio quirks, new Intel dspconf entries"

* tag 'sound-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek: Add quirk for Clevo NS50PU
  ALSA: hda: Fix discovery of i915 graphics PCI device
  ALSA: hda/via: Fix missing beep setup
  ALSA: hda/conexant: Fix missing beep setup
  ALSA: memalloc: Drop x86-specific hack for WC allocations
  ALSA: hda/realtek: Add quirk for Clevo PD70PNT
  ALSA: x86: intel_hdmi_audio: use pm_runtime_resume_and_get()
  ALSA: x86: intel_hdmi_audio: enable pm_runtime and set autosuspend delay
  ALSA: hda: intel-nhlt: remove use of __func__ in dev_dbg
  ALSA: hda: intel-dspcfg: use SOF for UpExtreme and UpExtreme11 boards
  firewire: convert sysfs sprintf/snprintf family to sysfs_emit
  firewire: cdev: fix potential leak of kernel stack due to uninitialized value
  ALSA: hda/realtek: Apply fixup for Lenovo Yoga Duet 7 properly
  ALSA: hda/realtek - ALC897 headset MIC no sound
  ALSA: usb-audio: US16x08: Move overflow check before array access
  ALSA: hda/realtek: Add mute LED quirk for HP Omen laptop

When a packet enters the OVS datapath and does not match any existing
flows installed in the kernel flow cache, the packet will be sent to
userspace to be parsed, and a new flow will be created. The kernel and
OVS rely on each other to parse packet fields in the same way so that
packets will be handled properly.

As per the design document linked below, OVS expects all later IPv6
fragments to have nw_proto=44 in the flow key, so they can be correctly
matched on OpenFlow rules. OpenFlow controllers create pipelines based
on this design.

This behavior was changed by the commit in the Fixes tag so that
nw_proto equals the next_header field of the last extension header.
However, there is no counterpart for this change in OVS userspace,
meaning that this field is parsed differently between OVS and the
kernel. This is a problem because OVS creates actions based on what is
parsed in userspace, but the kernel-provided flow key is used as a match
criteria, as described in Documentation/networking/openvswitch.rst. This
leads to issues such as packets incorrectly matching on a flow and thus
the wrong list of actions being applied to the packet. Such changes in
packet parsing cannot be implemented without breaking the userspace.

The offending commit is partially reverted to restore the expected
behavior.

The change technically made sense and there is a good reason that it was
implemented, but it does not comply with the original design of OVS.
If in the future someone wants to implement such a change, then it must
be user-configurable and disabled by default to preserve backwards
compatibility with existing OVS versions.

Cc: stable@vger.kernel.org
Fixes: fa642f08 ("openvswitch: Derive IP protocol number for IPv6 later frags")
Link: https://docs.openvswitch.org/en/latest/topics/design/#fragmentsSigned-off-by: Rosemarie O'Riorden <roriorden@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220621204845.9721-1-roriorden@redhat.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Commit 8a59f9d1 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()")
has moved the inet_csk_has_ulp(sk) check from sk_psock_init() to
the new tcp_bpf_update_proto() function. I'm guessing that this
was done to allow creating psocks for non-inet sockets.

Unfortunately the destruction path for psock includes the ULP
unwind, so we need to fail the sk_psock_init() itself.
Otherwise if ULP is already present we'll notice that later,
and call tcp_update_ulp() with the sk_proto of the ULP
itself, which will most likely result in the ULP looping
its callbacks.

Fixes: 8a59f9d1 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Tested-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/r/20220620191353.1184629-2-kuba@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

This reverts commit 69135c57.

This commit was just papering over the issue, ULP should not
get ->update() called with its own sk_prot. Each ULP would
need to add this check.

Fixes: 69135c57 ("net/tls: fix tls_sk_proto_close executed repeatedly")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20220620191353.1184629-1-kuba@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The following sequence currently causes a driver bug warning
when using virtio_net:

  # ip link set eth0 up
  # echo mem > /sys/power/state (or e.g. # rtcwake -s 10 -m mem)
  <resume>
  # ip link set eth0 down

  Missing register, driver bug
  WARNING: CPU: 0 PID: 375 at net/core/xdp.c:138 xdp_rxq_info_unreg+0x58/0x60
  Call trace:
   xdp_rxq_info_unreg+0x58/0x60
   virtnet_close+0x58/0xac
   __dev_close_many+0xac/0x140
   __dev_change_flags+0xd8/0x210
   dev_change_flags+0x24/0x64
   do_setlink+0x230/0xdd0
   ...

This happens because virtnet_freeze() frees the receive_queue
completely (including struct xdp_rxq_info) but does not call
xdp_rxq_info_unreg(). Similarly, virtnet_restore() sets up the
receive_queue again but does not call xdp_rxq_info_reg().

Actually, parts of virtnet_freeze_down() and virtnet_restore_up()
are almost identical to virtnet_close() and virtnet_open(): only
the calls to xdp_rxq_info_(un)reg() are missing. This means that
we can fix this easily and avoid such problems in the future by
just calling virtnet_close()/open() from the freeze/restore handlers.

Aside from adding the missing xdp_rxq_info calls the only difference
is that the refill work is only cancelled if netif_running(). However,
this should not make any functional difference since the refill work
should only be active if the network interface is actually up.

Fixes: 754b8a21 ("virtio_net: setup xdp_rxq_info")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220621114845.3650258-1-stephan.gerhold@kernkonzept.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-06-21

This series contains updates to ice driver only.

Marcin fixes GTP filters by allowing ignoring of the inner ethertype field.

Wojciech adds VSI handle tracking in order to properly distinguish similar
filters for removal.

Anatolii removes ability to set 1000baseT and 1000baseX fields
concurrently which caused link issues. He also disallows setting
channels to less than the number of Traffic Classes which would cause
NULL pointer dereference.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  ice: ethtool: Prohibit improper channel config for DCB
  ice: ethtool: advertise 1000M speeds properly
  ice: Fix switchdev rules book keeping
  ice: ignore protocol field in GTP offload
====================

Link: https://lore.kernel.org/r/20220621224756.631765-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.

According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.

In addition to that, commit b6e0c419 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.

Fixes: b6e0c419 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The current mgmt ethernet timeout is set to 100ms. This value is too
big and would slow down any mdio command in case the mgmt ethernet
packet have some problems on the receiving part.
Reduce it to just 5ms to handle case when some operation are done on the
master port that would cause the mgmt ethernet to not work temporarily.

Fixes: 5950c7c0 ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151633.11741-1-ansuelsmth@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

It was discovered that the Documentation lacks of a fundamental detail
on how to correctly change the MAX_FRAME_SIZE of the switch.

In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the
switch panics and cease to send any packet. This cause the mgmt ethernet
system to not receive any packet (the slow fallback still works) and
makes the device not reachable. To recover from this a switch reset is
required.

To correctly handle this, turn off the cpu ports before changing the
MAX_FRAME_SIZE and turn on again after the value is applied.

Fixes: f58d2598 ("net: dsa: qca8k: implement the port MTU callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151122.10220-1-ansuelsmth@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

I've been contributing and reviewing patches for ptp_ocp driver for
some time and I'm taking care of it's github mirror. On Jakub's
suggestion, I would like to step forward and become a maintainer for
this driver. This patch adds a dedicated entry to MAINTAINERS.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220621233131.21240-1-vfedorenko@novek.ruSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-kselftest-fixes-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fixes from Shuah Khan:
 "Compile time fixes and run-time resources leaks:

   - Fix clang cross compilation

   - Fix resource leak when return error

   - fix compile error for dma_map_benchmark

   - Fix regression - make use of GUP_TEST_FILE macro"

* tag 'linux-kselftest-fixes-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests: make use of GUP_TEST_FILE macro
  selftests: vm: Fix resource leak when return error
  selftests dma: fix compile error for dma_map_benchmark
  selftests: Fix clang cross compilation

Under CONFIG_FORTIFY_SOURCE=y and CONFIG_UBSAN_BOUNDS=y, Clang is bugged
here for calculating the size of the destination buffer (0x10 instead of
0x14). This copy is a fixed size (sizeof(struct fw_section_info_st)), with
the source and dest being struct fw_section_info_st, so the memcpy should
be safe, assuming the index is within bounds, which is UBSAN_BOUNDS's
responsibility to figure out.

Avoid the whole thing and just do a direct assignment. This results in
no change to the executable code.

[This is a duplicate of commit 2c0ab32b ("hinic: Replace memcpy()
 with direct assignment") which was applied to net-next.]

Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Tom Rix <trix@redhat.com>
Cc: llvm@lists.linux.dev
Link: https://github.com/ClangBuiltLinux/linux/issues/1592Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Link: https://lore.kernel.org/r/20220616052312.292861-1-keescook@chromium.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fixes headset detection on Clevo NS50PU.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220622150017.9897-1-tcrawford@system76.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Pull 9pfs fixes from Dominique Martinet:
 "A couple of fid refcount and fscache fixes:

   - fid refcounting was incorrect in some corner cases and would leak
     resources, only freed at umount time. The first three commits fix
     three such cases

   - 'cache=loose' or fscache was broken when trying to write a partial
     page to a file with no read permission since the rework a few
     releases ago.

     The fix taken here is just to restore old behavior of using the
     special 'writeback_fid' for such reads, which is open as root/RDWR
     and such not get complains that we try to read on a WRONLY fid.

     Long-term it'd be nice to get rid of this and not issue the read at
     all (skip cache?) in such cases, but that direction hasn't
     progressed"

* tag '9p-for-5.19-rc4' of https://github.com/martinetd/linux:
  9p: fix EBADF errors in cached mode
  9p: Fix refcounting during full path walks for fid lookups
  9p: fix fid refcount leak in v9fs_vfs_get_link
  9p: fix fid refcount leak in v9fs_vfs_atomic_open_dotl

This reverts commit 8fc74d18.

BAR0 is the main (only?) register bank for this device. We most
obviously can't unmap it before the netdev is unregistered.
This was pointed out in review but the patch got reposted and
merged, anyway.

The author of the patch was only testing it with a QEMU model,
which I presume does not emulate enough for the netdev to be brought
up (author's replies are not visible in lore because they kept sending
their emails in HTML).

Link: https://lore.kernel.org/all/20220616085059.680dc215@kernel.org/
Fixes: 8fc74d18 ("drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

1) Use get_random_u32() instead of prandom_u32_state() in nft_meta
   and nft_numgen, from Florian Westphal.

2) Incorrect list head in nfnetlink_cttimeout in recent update coming
   from previous development cycle. Also from Florian.

3) Incorrect path to pktgen scripts for nft_concat_range.sh selftest.
   From Jie2x Zhou.

4) Two fixes for the for nft_fwd and nft_dup egress support, from Florian.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: nf_dup_netdev: add and use recursion counter
  netfilter: nf_dup_netdev: do not push mac header a second time
  selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh
  netfilter: cttimeout: fix slab-out-of-bounds read typo in cttimeout_net_exit
  netfilter: use get_random_u32 instead of prandom
====================

Link: https://lore.kernel.org/r/20220621085618.3975-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>