- 10 Oct, 2007 40 commits
-
-
Johannes Berg authored
The key_mgmt variable for STA interfaces doesn't seem well-defined nor do we actually use the values other than "NONE", so change it to be named better. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Acked-by:
Michael Wu <flamingice@sourmilk.net> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Johannes Berg authored
The ioctls * PRISM2_PARAM_RADAR_DETECT * PRISM2_PARAM_SPECTRUM_MGMT are not used by hostapd or wpa_supplicant, Signed-off-by:
-
Johannes Berg authored
The ioctls * PRISM2_PARAM_STA_ANTENNA_SEL * PRISM2_PARAM_TX_POWER_REDUCTION * PRISM2_PARAM_DEFAULT_WEP_ONLY are not used by hostapd or wpa_supplicant. Signed-off-by:
-
Johannes Berg authored
The ioctls * PRISM2_PARAM_ANTENNA_MODE * PRISM2_PARAM_STAT_TIME are not used by hostapd or wpa_supplicant. Signed-off-by:
-
Johannes Berg authored
When doing key selection for software decryption, mac80211 gets a few things wrong: it always uses pairwise keys if configured, even if the frame is addressed to a multicast address. Also, it doesn't allow using a key index of zero if a pairwise key has also been found. This patch changes the key selection code to be (more) in line with the 802.11 specification. I have confirmed that with this, multicast frames are correctly decrypted and I've tested with WEP as well. While at it, I've cleaned up the semantics of the hardware flags IEEE80211_HW_WEP_INCLUDE_IV and IEEE80211_HW_DEVICE_HIDES_WEP and clarified them in the mac80211.h header; it is also now allowed to set the IEEE80211_HW_DEVICE_HIDES_WEP option even if it only applies to frames that have been decrypted by the hw, unencrypted frames must be dropped but encrypted frames that the hardware couldn't handle can be passed up unmodified. Signed-off-by:
-
Johannes Berg authored
Unused in drivers, userspace and mac80211. Signed-off-by:
-
Johannes Berg authored
Neither hostapd nor wpa_supplicant really use it. Signed-off-by:
-
Johannes Berg authored
Many if not all of these messages can be triggered by sending a few rogue frames which is trivially done and then we overflow our logs. Signed-off-by:
-
Johannes Berg authored
Signed-off-by:
-
Johannes Berg authored
This now is unused in hostapd/wpa_supplicant. Signed-off-by:
-
Johannes Berg authored
The flag is never checked because drivers can simply call ieee80211_beacon_get() regardless of setting this flag. Signed-off-by:
-
Johannes Berg authored
The callback isn't used so remove it. Signed-off-by:
-
Johannes Berg authored
This fixes two issues with the key debugfs: 1) key index obviously isn't unique 2) various missing break statements led to bogus output Signed-off-by:
-
Johannes Berg authored
David Woodhouse noticed that under some circumstances the number of slab allocations kept growing. After looking a bit, this seemed to happen when you had a management mode interface that was *down*. The reason for this is that when the device is down, all management frames get queued to the in-kernel MLME (via ieee80211_sta_rx_mgmt) but then the sta work is invoked but doesn't run when the netif is down. When you then bring the interface up, all such frames are freed, but if you change the mode all of them are lost because the skb queue is reinitialised as soon as you go back to managed mode. The skb queue is correctly cleared when the interface is brought down, but the code doesn't account for the fact that it may be filled while it is not up. This patch should fix the issue by simply ignoring all interfaces that are down when going through the RX handlers. Signed-off-by:
-
Alex Villacís Lasso authored
This dongle does not follow the usb-irda specification, so it needs its own special driver. First, it uses control URBs for data transfer, instead of bulk or interrupt transfers; the only interrupt endpoint exposed seems to be a dummy to prevent the interface from being rejected. Second, it uses obfuscation and padding at the USB traffic level, for no apparent reason other than to make reverse engineering harder (full details on obfuscation in comments at beginning of source). Although it is advertised as a "4 Mbps FIR dongle", it apparently loses packets at speeds greater than 57600 bps. On plugin, this dongle reports vendor and device IDs: 0x07d0:0x4959 . The Windows driver that is used normally to control this dongle has a filename of KS-959.SYS . Signed-off-by:
Alex Villacís Lasso <a_villacis@palosanto.com> Signed-off-by:
Samuel Ortiz <samuel@sortiz.org> Signed-off-by:
-
Alex Villacís Lasso authored
This dongle does not follow the usb-irda specification, so it needs its own special driver. Just like the Kingsun/Donshine dongle, it exposes two interrupt endpoints. Reception is performed through direct reads from the input endpoint. Transmission requires splitting the IrDA frames into 8-byte segments, in which the first byte encodes how many of the remaining 7 bytes are used as data. Speed change is made with a control URB just like the one in cypress_m8, and it seems to support up to 115200 bps. On plugin, this dongle reports vendor and device IDs: 0x07d0:0x4100 Signed-off-by:
-
Samuel Ortiz authored
Signed-off-by:
-
Ilpo Järvinen authored
Hopefully captured all single statement cases under net/. I'm not too sure if there is some policy about #includes that are "guaranteed" (ie., in the current tree) to be available through some other #included header, so I just added linux/kernel.h to each changed file that didn't #include it previously. Signed-off-by:
Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by:
-
Robert Olsson authored
As noted by Christoph Hellwig, pktgen was the only user so it can now be removed. [ Add missing cases caught by Adrian Bunk. -DaveM ] Signed-off-by:
Robert Olsson <robert.olsson@its.uu.se> Signed-off-by:
-
Robert Olsson authored
It's not a job for pktgen. Signed-off-by:
-
Robert Olsson authored
Below some pktgen support to send into different TX queues. This can of course be feed into input queues on other machines Signed-off-by:
-
Denis Cheng authored
This could make future redesign of struct netlink_sock easier. Signed-off-by:
Denis Cheng <crquan@gmail.com> Signed-off-by:
-
Thomas Graf authored
Signed-off-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
Masahide NAKAMURA authored
IPv4 IPsec tunnel gateway incorrectly sends redirect to sender if it is onlink host when network device the IPsec tunnelled packet is arrived is the same as the one the decapsulated packet is sent. With this patch, it omits to send the redirect when the forwarding skbuff carries secpath, since such skbuff should be assumed as a decapsulated packet from IPsec tunnel by own. Request for comments: Alternatively we'd have another way to change net/ipv4/route.c (__mkroute_input) to use RTCF_DOREDIRECT flag unless skbuff has no secpath. It is better than this patch at performance point of view because IPv4 redirect judgement is done at routing slow-path. However, it should be taken care of resource changes between SAD(XFRM states) and routing table. In other words, When IPv4 SAD is changed does the related routing entry go to its slow-path? If not, it is reasonable to apply this patch. Signed-off-by:
Masahide NAKAMURA <nakam@linux-ipv6.org> Signed-off-by:
-
Masahide NAKAMURA authored
IPv6 IPsec tunnel gateway incorrectly sends redirect to router or sender when network device the IPsec tunnelled packet is arrived is the same as the one the decapsulated packet is sent. With this patch, it omits to send the redirect when the forwarding skbuff carries secpath, since such skbuff should be assumed as a decapsulated packet from IPsec tunnel by own. It may be a rare case for an IPsec security gateway, however it is not rare when the gateway is MIPv6 Home Agent since the another tunnel end-point is Mobile Node and it changes the attached network. Signed-off-by:
-
Noriaki TAKAMIYA authored
When XFRM policy and state are ready after TCP connection is started, the traffic should be transformed immediately, however it does not on IPv6 TCP. It depends on a dst cache replacement policy with connected socket. It seems that the replacement is always done for IPv4, however, on IPv6 case it is done only when routing cookie is changed. This patch fix that non-transformation dst can be changed to transformation one. This behavior is required by MIPv6 and improves IPv6 IPsec. Fixes by Masahide NAKAMURA. Signed-off-by:
Noriaki TAKAMIYA <takamiya@po.ntts.co.jp> Signed-off-by:
-
Brian Haley authored
Add v4mapped address inline to avoid calls to ipv6_addr_type(). Signed-off-by:
Brian Haley <brian.haley@hp.com> Signed-off-by:
-
Stephen Hemminger authored
This driver has been marked obsolete for a long time and is superseded by traffic schedulers. Signed-off-by:
Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by:
-
Stephen Hemminger authored
This patch causes UDP port allocation to be randomized like TCP. The earlier code would always choose same port (ie first empty list). Signed-off-by:
-
Ilpo Järvinen authored
Signed-off-by:
-
Ilpo Järvinen authored
In DSACK case, some events are not extraordinary, such as packet duplication generated DSACK. They can arrive easily below snd_una when undo_marker is not set (TCP being in CA_Open), counting such DSACKs amoung SACK discards will likely just mislead if they occur in some scenario when there are other problems as well. Similarly, excessively delayed packets could cause "normal" DSACKs. Therefore, separate counters are allocated for DSACK events. Signed-off-by:
-
Ilpo Järvinen authored
SACK processing code has been a sort of russian roulette as no validation of SACK blocks is previously attempted. Besides, it is not very clear what all kinds of broken SACK blocks really mean (e.g., one that has start and end sequence numbers reversed). So now close the roulette once and for all. Signed-off-by:
-
Ilpo Järvinen authored
Only thing that tiny function does is rearming the RTO (if necessary), name it accordingly. Signed-off-by:
-
Ilpo Järvinen authored
Signed-off-by:
-
Ilpo Järvinen authored
Makes caller side more obvious, there's no need to have a wrapper for this oneliner! Signed-off-by:
-
Stephen Hemminger authored
Get rid of using DPRINTK macro in ATM and use pr_debug (in kernel.h). Using the standard macro is cleaner and forces code to check for bad arguments and formatting. Fixes from Thomas Graf. Signed-off-by:
-
Stephen Hemminger authored
The ethernet header management only needs to handle a fixed size address (6 bytes). If the memcpy/memset are changed to be passed a constant length, then compiler can optimize for this case (and if it is smart eliminate string instructions). Signed-off-by:
-
Thomas Graf authored
These functions are only used once and are a lot easier to understand if inlined directly into the function. Fixes by Masahide NAKAMURA. Signed-off-by:
-
Thomas Graf authored
Signed-off-by:
-
Thomas Graf authored
Signed-off-by:
-
