- 12 May, 2022 6 commits
-
-
Amit Cohen authored
IPv6 addresses which are used for tunnels are stored in a hash table with reference counting. When a new GRE tunnel is configured, the driver is notified and configures it in hardware. Currently, any change in the tunnel is not applied in the driver. It means that if the remote address is changed, the driver is not aware of this change and the first address will be used. This behavior results in a warning [1] in scenarios such as the following: # ip link add name gre1 type ip6gre local 2000::3 remote 2000::fffe tos inherit ttl inherit # ip link set name gre1 type ip6gre local 2000::3 remote 2000::ffff ttl inherit # ip link delete gre1 The change of the address is not applied in the driver. Currently, the driver uses the remote address which is stored in the 'parms' of the overlay device. When the tunnel is removed, the new IPv6 address is used, the driver tries to release it, but as it is not aware of the change, this address is not configured and it warns about releasing non existing IPv6 address. Fix it by using the IPv6 address which is cached in the IPIP entry, this address is the last one that the driver used, so even in cases such the above, the first address will be released, without any warning. [1]: WARNING: CPU: 1 PID: 2197 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2920 mlxsw_sp_ipv6_addr_put+0x146/0x220 [mlxsw_spectrum] ... CPU: 1 PID: 2197 Comm: ip Not tainted 5.17.0-rc8-custom-95062-gc1e5ded51a9a #84 Hardware name: Mellanox Technologies Ltd. MSN4700/VMOD0010, BIOS 5.11 07/12/2021 RIP: 0010:mlxsw_sp_ipv6_addr_put+0x146/0x220 [mlxsw_spectrum] ... Call Trace: <TASK> mlxsw_sp2_ipip_rem_addr_unset_gre6+0xf1/0x120 [mlxsw_spectrum] mlxsw_sp_netdevice_ipip_ol_event+0xdb/0x640 [mlxsw_spectrum] mlxsw_sp_netdevice_event+0xc4/0x850 [mlxsw_spectrum] raw_notifier_call_chain+0x3c/0x50 call_netdevice_notifiers_info+0x2f/0x80 unregister_netdevice_many+0x311/0x6d0 rtnl_dellink+0x136/0x360 rtnetlink_rcv_msg+0x12f/0x380 netlink_rcv_skb+0x49/0xf0 netlink_unicast+0x233/0x340 netlink_sendmsg+0x202/0x440 ____sys_sendmsg+0x1f3/0x220 ___sys_sendmsg+0x70/0xb0 __sys_sendmsg+0x54/0xa0 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae Fixes: e846efe2 ("mlxsw: spectrum: Add hash table for IPv6 address mapping") Reported-by:
Maksym Yaremchuk <maksymy@nvidia.com> Signed-off-by:
Amit Cohen <amcohen@nvidia.com> Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Link: https://lore.kernel.org/r/20220511115747.238602-1-idosch@nvidia.comSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Florian Fainelli authored
The interrupt controller supplying the Wake-on-LAN interrupt line maybe modular on some platforms (irq-bcm7038-l1.c) and might be probed at a later time than the GENET driver. We need to specifically check for -EPROBE_DEFER and propagate that error to ensure that we eventually fetch the interrupt descriptor. Fixes: 9deb48b5 ("bcmgenet: add WOL IRQ check") Fixes: 5b1f0e62 ("net: bcmgenet: Avoid touching non-existent interrupt") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/20220511031752.2245566-1-f.fainelli@gmail.comSigned-off-by:
-
Yang Yingliang authored
'foe_table' is a pointer, the real size of struct mtk_foe_entry should be pass to memset(). Fixes: ba37b7ca ("net: ethernet: mtk_eth_soc: add support for initializing the PPE") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Acked-by:
Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20220511030829.3308094-1-yangyingliang@huawei.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetoothJakub Kicinski authored
Luiz Augusto von Dentz says: ==================== bluetooth pull request for net: - Fix the creation of hdev->name when index is greater than 9999 * tag 'for-net-2022-05-11' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth: Bluetooth: Fix the creation of hdev->name ==================== Link: https://lore.kernel.org/r/20220512002901.823647-1-luiz.dentz@gmail.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wirelessJakub Kicinski authored
Kalle Valo says: ==================== wireless fixes for v5.18 Second set of fixes for v5.18 and hopefully the last one. We have a new iwlwifi maintainer, a fix to rfkill ioctl interface and important fixes to both stack and two drivers. * tag 'wireless-2022-05-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: rfkill: uapi: fix RFKILL_IOCTL_MAX_SIZE ioctl request definition nl80211: fix locking in nl80211_set_tx_bitrate_mask() mac80211_hwsim: call ieee80211_tx_prepare_skb under RCU protection mac80211_hwsim: fix RCU protected chanctx access mailmap: update Kalle Valo's email mac80211: Reset MBSSID parameters upon connection cfg80211: retrieve S1G operating channel number nl80211: validate S1G channel width mac80211: fix rx reordering with non explicit / psmp ack policy ath11k: reduce the wait time of 11d scan and hw scan while add interface MAINTAINERS: update iwlwifi driver maintainer iwlwifi: iwl-dbg: Use del_timer_sync() before freeing ==================== Link: https://lore.kernel.org/r/20220511154535.A1A12C340EE@smtp.kernel.orgSigned-off-by:
-
Itay Iellin authored
Set a size limit of 8 bytes of the written buffer to "hdev->name" including the terminating null byte, as the size of "hdev->name" is 8 bytes. If an id value which is greater than 9999 is allocated, then the "snprintf(hdev->name, sizeof(hdev->name), "hci%d", id)" function call would lead to a truncation of the id value in decimal notation. Set an explicit maximum id parameter in the id allocation function call. The id allocation function defines the maximum allocated id value as the maximum id parameter value minus one. Therefore, HCI_MAX_ID is defined as 10000. Signed-off-by:
Itay Iellin <ieitayie@gmail.com> Signed-off-by:
Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
-
- 11 May, 2022 12 commits
-
-
Xiaomeng Tong authored
The bug is here: ret = i40e_add_macvlan_filter(hw, ch->seid, vdev->dev_addr, &aq_err); The list iterator 'ch' will point to a bogus position containing HEAD if the list is empty or no element is found. This case must be checked before any use of the iterator, otherwise it will lead to a invalid memory access. To fix this bug, use a new variable 'iter' as the list iterator, while use the origin variable 'ch' as a dedicated pointer to point to the found element. Cc: stable@vger.kernel.org Fixes: 1d8d80b4 ("i40e: Add macvlan support on i40e") Signed-off-by:
Xiaomeng Tong <xiam0nd.tong@gmail.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220510204846.2166999-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Paolo Abeni authored
Currently pedit tries to ensure that the accessed skb offset is writable via skb_unclone(). The action potentially allows touching any skb bytes, so it may end-up modifying shared data. The above causes some sporadic MPTCP self-test failures, due to this code: tc -n $ns2 filter add dev ns2eth$i egress \ protocol ip prio 1000 \ handle 42 fw \ action pedit munge offset 148 u8 invert \ pipe csum tcp \ index 100 The above modifies a data byte outside the skb head and the skb is a cloned one, carrying a TCP output packet. This change addresses the issue by keeping track of a rough over-estimate highest skb offset accessed by the action and ensuring such offset is really writable. Note that this may cause performance regressions in some scenarios, but hopefully pedit is not in the critical path. Fixes: db2c2417 ("act_pedit: access skb->data safely") Acked-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Tested-by:
Geliang Tang <geliang.tang@suse.com> Signed-off-by:
Jamal Hadi Salim <jhs@mojatatu.com> Link: https://lore.kernel.org/r/1fcf78e6679d0a287dd61bb0f04730ce33b3255d.1652194627.git.pabeni@redhat.comSigned-off-by:
-
David S. Miller authored
Alexandra Winter says: ==================== s390/net: Cleanup some code checker findings clean up smatch findings in legacy code. I was not able to provoke any real failures on my systems, but other hardware reactions, timing conditions or compiler output, may cause failures. There are still 2 smatch warnings left in s390/net: drivers/s390/net/ctcm_main.c:1326 add_channel() warn: missing error code 'rc' This one is a false positive. drivers/s390/net/netiucv.c:1355 netiucv_check_user() warn: argument 3 to %02x specifier has type 'char' Postponing this one, need to better understand string handling in iucv. There are several sparse warnings left in ctcm, like: drivers/s390/net/ctcm_fsms.c:573:9: warning: context imbalance in 'ctcm_chx_setmode' - different lock contexts for basic block Those are mentioned in the source, no plan to rework. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Alexandra Winter authored
smatch complains about drivers/s390/net/lcs.c:1741 lcs_get_control() warn: variable dereferenced before check 'card->dev' (see line 1739) Fixes: 27eb5ac8 ("[PATCH] s390: lcs driver bug fixes and improvements [1/2]") Signed-off-by:
Alexandra Winter <wintera@linux.ibm.com> Signed-off-by:
-
Alexandra Winter authored
smatch complains about drivers/s390/net/ctcm_mpc.c:1210 ctcmpc_unpack_skb() warn: possible memory leak of 'mpcginfo' mpc_action_discontact() did not free mpcginfo. Consolidate the freeing in ctcmpc_unpack_skb(). Fixes: 293d984f ("ctcm: infrastructure for replaced ctc driver") Signed-off-by:
-
Alexandra Winter authored
Found by cppcheck and smatch. smatch complains about drivers/s390/net/ctcm_sysfs.c:43 ctcm_buffer_write() warn: variable dereferenced before check 'priv' (see line 42) Fixes: 3c09e264 ("ctcm: rename READ/WRITE defines to avoid redefinitions") Reported-by:
Colin Ian King <colin.i.king@gmail.com> Signed-off-by:
-
David S. Miller authored
Grant Grundler says: ==================== net: atlantic: more fuzzing fixes It essentially describes four problems: 1) validate rxd_wb->next_desc_ptr before populating buff->next 2) "frag[0] not initialized" case in aq_ring_rx_clean() 3) limit iterations handling fragments in aq_ring_rx_clean() 4) validate hw_head_ in hw_atl_b0_hw_ring_tx_head_update() (1) was fixed by Zekun Shen <bruceshenzk@gmail.com> around the same time with "atlantic: Fix buff_ring OOB in aq_ring_rx_clean" (SHA1 5f501532). I've added one "clean up" contribution: "net: atlantic: reduce scope of is_rsc_complete" I tested the "original" patches using chromeos-v5.4 kernel branch: https://chromium-review.googlesource.com/q/hashtag:pcinet-atlantic-2022q1+(status:open%20OR%20status:merged) I've forward ported those patches to 5.18-rc2 and compiled them but am unable to test them on 5.18-rc2 kernel (logistics problems). Credit largely goes to ChromeOS Fuzzing team members: Aashay Shringarpure, Yi Chou, Shervin Oloumi V2 changes: o drop first patch - was already fixed upstream differently o reduce (4) "validate hw_head_" to simple bounds checking. ==================== Signed-off-by:
-
Grant Grundler authored
Bounds check hw_head index provided by NIC to verify it lies within the TX buffer ring. Reported-by:
Aashay Shringarpure <aashay@google.com> Reported-by:
Yi Chou <yich@google.com> Reported-by:
Shervin Oloumi <enlightened@google.com> Signed-off-by:
Grant Grundler <grundler@chromium.org> Signed-off-by:
-
Grant Grundler authored
Enforce that the CPU can not get stuck in an infinite loop. Reported-by:
-
Grant Grundler authored
Don't defer handling the err case outside the loop. That's pointless. And since is_rsc_complete is only used inside this loop, declare it inside the loop to reduce it's scope. Signed-off-by:
-
Grant Grundler authored
In aq_ring_rx_clean(), if buff->is_eop is not set AND buff->len < AQ_CFG_RX_HDR_SIZE, then hdr_len remains equal to buff->len and skb_add_rx_frag(xxx, *0*, ...) is not called. The loop following this code starts calling skb_add_rx_frag() starting with i=1 and thus frag[0] is never initialized. Since i is initialized to zero at the top of the primary loop, we can just reference and post-increment i instead of hardcoding the 0 when calling skb_add_rx_frag() the first time. Reported-by:
-
Yang Yingliang authored
Switch to using pcim_enable_device() to avoid missing pci_disable_device(). Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
-
- 10 May, 2022 9 commits
-
-
Wan Jiabing authored
In lanphy_read_page_reg, calling __phy_read() might return a negative error code. Use 'int' to check the error code. Fixes: 7c2dcfa2 ("net: phy: micrel: Add support for LAN8804 PHY") Signed-off-by:
Wan Jiabing <wanjiabing@vivo.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220509144519.2343399-1-wanjiabing@vivo.comSigned-off-by:
-
Kees Cook authored
Clang's structure layout randomization feature gets upset when it sees struct neighbor (which is randomized) cast to struct dn_neigh: net/decnet/dn_route.c:1123:15: error: casting from randomized structure pointer type 'struct neighbour *' to 'struct dn_neigh *' gateway = ((struct dn_neigh *)neigh)->addr; ^ Update all the open-coded casts to use container_of() to do the conversion instead of depending on strict member ordering. Reported-by:
kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/lkml/202205041247.WKBEHGS5-lkp@intel.com Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Yajun Deng <yajun.deng@linux.dev> Cc: Zheng Yongjun <zhengyongjun3@huawei.com> Cc: Bill Wendling <morbo@google.com> Cc: linux-decnet-user@lists.sourceforge.net Cc: netdev@vger.kernel.org Signed-off-by:
Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20220508102217.2647184-1-keescook@chromium.orgSigned-off-by:
-
Manuel Ullmann authored
The impact of this regression is the same for resume that I saw on thaw: the kernel hangs and nothing except SysRq rebooting can be done. Fixes regression in commit cbe6c3a8 ("net: atlantic: invert deep par in pm functions, preventing null derefs"), where I disabled deep pm resets in suspend and resume, trying to make sense of the atl_resume_common() deep parameter in the first place. It turns out, that atlantic always has to deep reset on pm operations. Even though I expected that and tested resume, I screwed up by kexec-rebooting into an unpatched kernel, thus missing the breakage. This fixup obsoletes the deep parameter of atl_resume_common, but I leave the cleanup for the maintainers to post to mainline. Suspend and hibernation were successfully tested by the reporters. Fixes: cbe6c3a8 ("net: atlantic: invert deep par in pm functions, preventing null derefs") Link: https://lore.kernel.org/regressions/9-Ehc_xXSwdXcvZqKD5aSqsqeNj5Izco4MYEwnx5cySXVEc9-x_WC4C3kAoCqNTi-H38frroUK17iobNVnkLtW36V6VWGSQEOHXhmVMm5iQ=@protonmail.com/Reported-by:
Jordan Leppert <jordanleppert@protonmail.com> Reported-by:
Holger Hoffstaette <holger@applied-asynchrony.com> Tested-by:
Manuel Ullmann <labre@posteo.de> Link: https://lore.kernel.org/r/87bkw8dfmp.fsf@posteo.deSigned-off-by:
-
git://git.open-mesh.org/linux-mergeJakub Kicinski authored
Simon Wunderlich says: ==================== Here is a batman-adv bugfix: - Don't skb_split skbuffs with frag_list, by Sven Eckelmann * tag 'batadv-net-pullrequest-20220508' of git://git.open-mesh.org/linux-merge: batman-adv: Don't skb_split skbuffs with frag_list ==================== Link: https://lore.kernel.org/r/20220508132110.20451-1-sw@simonwunderlich.deSigned-off-by:
-
Vladimir Oltean authored
There is a race between switchdev_bridge_port_offload() and the dsa_port_switchdev_sync_attrs() call right below it. When switchdev_bridge_port_offload() finishes, FDB entries have been replayed by the bridge, but are scheduled for deferred execution later. However dsa_port_switchdev_sync_attrs -> dsa_port_can_apply_vlan_filtering() may impose restrictions on the vlan_filtering attribute and refuse offloading. When this happens, the delayed FDB entries will dereference dp->bridge, which is a NULL pointer because we have stopped the process of offloading this bridge. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Workqueue: dsa_ordered dsa_slave_switchdev_event_work pc : dsa_port_bridge_host_fdb_del+0x64/0x100 lr : dsa_slave_switchdev_event_work+0x130/0x1bc Call trace: dsa_port_bridge_host_fdb_del+0x64/0x100 dsa_slave_switchdev_event_work+0x130/0x1bc process_one_work+0x294/0x670 worker_thread+0x80/0x460 ---[ end trace 0000000000000000 ]--- Error: dsa_core: Must first remove VLAN uppers having VIDs also present in bridge. Fix the bug by doing what we do on the normal bridge leave path as well, which is to wait until the deferred FDB entries complete executing, then exit. The placement of dsa_flush_workqueue() after switchdev_bridge_port_unoffload() guarantees that both the FDB additions and deletions on rollback are waited for. Fixes: d7d0d423 ("net: dsa: flush switchdev workqueue when leaving the bridge") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220507134550.1849834-1-vladimir.oltean@nxp.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueJakub Kicinski authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2022-05-06 This series contains updates to ice driver only. Ivan Vecera fixes a race with aux plug/unplug by delaying setting adev until initialization is complete and adding locking. Anatolii ensures VF queues are completely disabled before attempting to reconfigure them. Michal ensures stale Tx timestamps are cleared from hardware. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: fix PTP stale Tx timestamps cleanup ice: clear stale Tx queue settings before configuring ice: Fix race during aux device (un)plugging ==================== Link: https://lore.kernel.org/r/20220506174129.4976-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Francesco Dolcini authored
This fixes the following error caused by a race condition between phydev->adjust_link() and a MDIO transaction in the phy interrupt handler. The issue was reproduced with the ethernet FEC driver and a micrel KSZ9031 phy. [ 146.195696] fec 2188000.ethernet eth0: MDIO read timeout [ 146.201779] ------------[ cut here ]------------ [ 146.206671] WARNING: CPU: 0 PID: 571 at drivers/net/phy/phy.c:942 phy_error+0x24/0x6c [ 146.214744] Modules linked in: bnep imx_vdoa imx_sdma evbug [ 146.220640] CPU: 0 PID: 571 Comm: irq/128-2188000 Not tainted 5.18.0-rc3-00080-gd569e869 #9 [ 146.229563] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 146.236257] unwind_backtrace from show_stack+0x10/0x14 [ 146.241640] show_stack from dump_stack_lvl+0x58/0x70 [ 146.246841] dump_stack_lvl from __warn+0xb4/0x24c [ 146.251772] __warn from warn_slowpath_fmt+0x5c/0xd4 [ 146.256873] warn_slowpath_fmt from phy_error+0x24/0x6c [ 146.262249] phy_error from kszphy_handle_interrupt+0x40/0x48 [ 146.268159] kszphy_handle_interrupt from irq_thread_fn+0x1c/0x78 [ 146.274417] irq_thread_fn from irq_thread+0xf0/0x1dc [ 146.279605] irq_thread from kthread+0xe4/0x104 [ 146.284267] kthread from ret_from_fork+0x14/0x28 [ 146.289164] Exception stack(0xe6fa1fb0 to 0xe6fa1ff8) [ 146.294448] 1fa0: 00000000 00000000 00000000 00000000 [ 146.302842] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 146.311281] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 146.318262] irq event stamp: 12325 [ 146.321780] hardirqs last enabled at (12333): [<c01984c4>] __up_console_sem+0x50/0x60 [ 146.330013] hardirqs last disabled at (12342): [<c01984b0>] __up_console_sem+0x3c/0x60 [ 146.338259] softirqs last enabled at (12324): [<c01017f0>] __do_softirq+0x2c0/0x624 [ 146.346311] softirqs last disabled at (12319): [<c01300ac>] __irq_exit_rcu+0x138/0x178 [ 146.354447] ---[ end trace 0000000000000000 ]--- With the FEC driver phydev->adjust_link() calls fec_enet_adjust_link() calls fec_stop()/fec_restart() and both these function reset and temporary disable the FEC disrupting any MII transaction that could be happening at the same time. fec_enet_adjust_link() and phy_read() can be running at the same time when we have one additional interrupt before the phy_state_machine() is able to terminate. Thread 1 (phylib WQ) | Thread 2 (phy interrupt) | | phy_interrupt() <-- PHY IRQ | handle_interrupt() | phy_read() | phy_trigger_machine() | --> schedule phylib WQ | | phy_state_machine() | phy_check_link_status() | phy_link_change() | phydev->adjust_link() | fec_enet_adjust_link() | --> FEC reset | phy_interrupt() <-- PHY IRQ | phy_read() | Fix this by acquiring the phydev lock in phy_interrupt(). Link: https://lore.kernel.org/all/20220422152612.GA510015@francesco-nb.int.toradex.com/ Fixes: c974bdbc ("net: phy: Use threaded IRQ, to allow IRQ from sleeping devices") cc: <stable@vger.kernel.org> Signed-off-by:
Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by:
-
Jesse Brandeburg authored
The W=2 build pointed out that the code wasn't initializing all the variables in the dim_cq_moder declarations with the struct initializers. The net change here is zero since these structs were already static const globals and were initialized with zeros by the compiler, but removing compiler warnings has value in and of itself. lib/dim/net_dim.c: At top level: lib/dim/net_dim.c:54:9: warning: missing initializer for field ‘comps’ of ‘const struct dim_cq_moder’ [-Wmissing-field-initializers] 54 | NET_DIM_RX_EQE_PROFILES, | ^~~~~~~~~~~~~~~~~~~~~~~ In file included from lib/dim/net_dim.c:6: ./include/linux/dim.h:45:13: note: ‘comps’ declared here 45 | u16 comps; | ^~~~~ and repeats for the tx struct, and once you fix the comps entry then the cq_period_mode field needs the same treatment. Use the commonly accepted style to indicate to the compiler that we know what we're doing, and add a comma at the end of each struct initializer to clean up the issue, and use explicit initializers for the fields we are initializing which makes the compiler happy. While here and fixing these lines, clean up the code slightly with a fix for the super long lines by removing the word "_MODERATION" from a couple defines only used in this file. Fixes: f8be17b8 ("lib/dim: Fix -Wunused-const-variable warnings") Signed-off-by:Jesse Brandeburg <jesse.brandeburg@intel.com> Link: https://lore.kernel.org/r/20220507011038.14568-1-jesse.brandeburg@intel.comSigned-off-by:
-
Jonathan Lemon authored
The initial code used roundup() to round the starting time to a multiple of a period. This generated an error on 32-bit systems, so was replaced with DIV_ROUND_UP_ULL(). However, this truncates to 32-bits on a 64-bit system. Replace with DIV64_U64_ROUND_UP() instead. Fixes: b325af3c ("ptp: ocp: Add signal generators and update sysfs nodes") Signed-off-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Link: https://lore.kernel.org/r/20220506223739.1930-2-jonathan.lemon@gmail.comSigned-off-by:
-
- 09 May, 2022 10 commits
-
-
Yang Yingliang authored
Fix the missing pci_disable_device() before return from tulip_init_one() in the error handling case. Reported-by:
-
Yang Yingliang authored
If ionic_map_bars() fails, pci_release_regions() need be called. Fixes: fbfb8031 ("ionic: Add hardware init and device commands") Signed-off-by:
-
Gleb Fotengauer-Malinovskiy authored
The definition of RFKILL_IOCTL_MAX_SIZE introduced by commit 54f586a9 ("rfkill: make new event layout opt-in") is unusable since it is based on RFKILL_IOC_EXT_SIZE which has not been defined. Fix that by replacing the undefined constant with the constant which is intended to be used in this definition. Fixes: 54f586a9 ("rfkill: make new event layout opt-in") Cc: stable@vger.kernel.org # 5.11+ Signed-off-by:
Gleb Fotengauer-Malinovskiy <glebfm@altlinux.org> Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Link: https://lore.kernel.org/r/20220506172454.120319-1-glebfm@altlinux.org [add commit message provided later by Dmitry] Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
This accesses the wdev's chandef etc., so cannot safely be used without holding the lock. Signed-off-by:
-
Johannes Berg authored
This is needed since it might use (and pass out) pointers to e.g. keys protected by RCU. Can't really happen here as the frames aren't encrypted, but we need to still adhere to the rules. Fixes: cacfddf8 ("mac80211_hwsim: initialize ieee80211_tx_info at hw_scan_work") Signed-off-by:
-
Johannes Berg authored
We need to RCU protect the chanctx_conf access, so do that. Fixes: 585625c9 ("mac80211_hwsim: check TX and STA bandwidth") Signed-off-by:
-
Kalle Valo authored
I switched to use my kernel.org address, the old kvalo@codeaurora.org address doesn't work anymore. Signed-off-by:
Kalle Valo <kvalo@kernel.org> Tested-by:
Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by:
-
Lina Wang authored
When NET_F_F_GRO_FRAGLIST is enabled and bpf_skb_change_proto is used, check if udp packets and tcp packets are successfully delivered to user space. If wrong udp packets are delivered, udpgso_bench_rx will exit with "Initial byte out of range" Signed-off-by:
Maciej enczykowski <maze@google.com> Signed-off-by:
Lina Wang <lina.wang@mediatek.com> Signed-off-by:
-
Lina Wang authored
When clatd starts with ebpf offloaing, and NETIF_F_GRO_FRAGLIST is enable, several skbs are gathered in skb_shinfo(skb)->frag_list. The first skb's ipv6 header will be changed to ipv4 after bpf_skb_proto_6_to_4, network_header\transport_header\mac_header have been updated as ipv4 acts, but other skbs in frag_list didnot update anything, just ipv6 packets. udp_queue_rcv_skb will call skb_segment_list to traverse other skbs in frag_list and make sure right udp payload is delivered to user space. Unfortunately, other skbs in frag_list who are still ipv6 packets are updated like the first skb and will have wrong transport header length. e.g.before bpf_skb_proto_6_to_4,the first skb and other skbs in frag_list has the same network_header(24)& transport_header(64), after bpf_skb_proto_6_to_4, ipv6 protocol has been changed to ipv4, the first skb's network_header is 44,transport_header is 64, other skbs in frag_list didnot change.After skb_segment_list, the other skbs in frag_list has different network_header(24) and transport_header(44), so there will be 20 bytes different from original,that is difference between ipv6 header and ipv4 header. Just change transport_header to be the same with original. Actually, there are two solutions to fix it, one is traversing all skbs and changing every skb header in bpf_skb_proto_6_to_4, the other is modifying frag_list skb's header in skb_segment_list. Considering efficiency, adopt the second one--- when the first skb and other skbs in frag_list has different network_header length, restore them to make sure right udp payload is delivered to user space. Signed-off-by:
-
Taehee Yoo authored
It fixes memory leak in ring buffer change logic. When ring buffer size is changed(ethtool -G eth0 rx 4096), sfc driver works like below. 1. stop all channels and remove ring buffers. 2. allocates new buffer array. 3. allocates rx buffers. 4. start channels. While the above steps are working, it skips some steps if the channel doesn't have a ->copy callback function. Due to ptp channel doesn't have ->copy callback, these above steps are skipped for ptp channel. It eventually makes some problems. a. ptp channel's ring buffer size is not changed, it works only 1024(default). b. memory leak. The reason for memory leak is to use the wrong ring buffer values. There are some values, which is related to ring buffer size. a. efx->rxq_entries - This is global value of rx queue size. b. rx_queue->ptr_mask - used for access ring buffer as circular ring. - roundup_pow_of_two(efx->rxq_entries) - 1 c. rx_queue->max_fill - efx->rxq_entries - EFX_RXD_HEAD_ROOM These all values should be based on ring buffer size consistently. But ptp channel's values are not. a. efx->rxq_entries - This is global(for sfc) value, always new ring buffer size. b. rx_queue->ptr_mask - This is always 1023(default). c. rx_queue->max_fill - This is new ring buffer size - EFX_RXD_HEAD_ROOM. Let's assume we set 4096 for rx ring buffer, normal channel ptp channel efx->rxq_entries 4096 4096 rx_queue->ptr_mask 4095 1023 rx_queue->max_fill 4086 4086 sfc driver allocates rx ring buffers based on these values. When it allocates ptp channel's ring buffer, 4086 ring buffers are allocated then, these buffers are attached to the allocated array. But ptp channel's ring buffer array size is still 1024(default) and ptr_mask is still 1023 too. So, 3062 ring buffers will be overwritten to the array. This is the reason for memory leak. Test commands: ethtool -G <interface name> rx 4096 while : do ip link set <interface name> up ip link set <interface name> down done In order to avoid this problem, it adds ->copy callback to ptp channel type. So that rx_queue->ptr_mask value will be updated correctly. Fixes: 7c236c43 ("sfc: Add support for IEEE-1588 PTP") Signed-off-by:Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
- 06 May, 2022 3 commits
-
-
Kees Cook authored
Using min_t(int, ...) as a potential array index implies to the compiler that negative offsets should be allowed. This is not the case, though. Replace "int" with "unsigned int". Fixes the following warning exposed under future CONFIG_FORTIFY_SOURCE improvements: In file included from include/linux/string.h:253, from include/linux/bitmap.h:11, from include/linux/cpumask.h:12, from include/linux/smp.h:13, from include/linux/lockdep.h:14, from include/linux/rcupdate.h:29, from include/linux/rculist.h:11, from include/linux/pid.h:5, from include/linux/sched.h:14, from include/linux/delay.h:23, from drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:35: drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function 't4_get_raw_vpd_params': include/linux/fortify-string.h:46:33: warning: '__builtin_memcpy' pointer overflow between offset 29 and size [2147483648, 4294967295] [-Warray-bounds] 46 | #define __underlying_memcpy __builtin_memcpy | ^ include/linux/fortify-string.h:388:9: note: in expansion of macro '__underlying_memcpy' 388 | __underlying_##op(p, q, __fortify_size); \ | ^~~~~~~~~~~~~ include/linux/fortify-string.h:433:26: note: in expansion of macro '__fortify_memcpy_chk' 433 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \ | ^~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2796:9: note: in expansion of macro 'memcpy' 2796 | memcpy(p->id, vpd + id, min_t(int, id_len, ID_LEN)); | ^~~~~~ include/linux/fortify-string.h:46:33: warning: '__builtin_memcpy' pointer overflow between offset 0 and size [2147483648, 4294967295] [-Warray-bounds] 46 | #define __underlying_memcpy __builtin_memcpy | ^ include/linux/fortify-string.h:388:9: note: in expansion of macro '__underlying_memcpy' 388 | __underlying_##op(p, q, __fortify_size); \ | ^~~~~~~~~~~~~ include/linux/fortify-string.h:433:26: note: in expansion of macro '__fortify_memcpy_chk' 433 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \ | ^~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2798:9: note: in expansion of macro 'memcpy' 2798 | memcpy(p->sn, vpd + sn, min_t(int, sn_len, SERNUM_LEN)); | ^~~~~~ Additionally remove needless cast from u8[] to char * in last strim() call. Reported-by: -
Eric Dumazet authored
netlink_recvmsg() does not need to change transport header. If transport header was needed, it should have been reset by the producer (netlink_dump()), not the consumer(s). The following trace probably happened when multiple threads were using MSG_PEEK. BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg write to 0xffff88811e9f15b2 of 2 bytes by task 32012 on cpu 1: skb_reset_transport_header include/linux/skbuff.h:2760 [inline] netlink_recvmsg+0x1de/0x790 net/netlink/af_netlink.c:1978 sock_recvmsg_nosec net/socket.c:948 [inline] sock_recvmsg net/socket.c:966 [inline] __sys_recvfrom+0x204/0x2c0 net/socket.c:2097 __do_sys_recvfrom net/socket.c:2115 [inline] __se_sys_recvfrom net/socket.c:2111 [inline] __x64_sys_recvfrom+0x74/0x90 net/socket.c:2111 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae write to 0xffff88811e9f15b2 of 2 bytes by task 32005 on cpu 0: skb_reset_transport_header include/linux/skbuff.h:2760 [inline] netlink_recvmsg+0x1de/0x790 net/netlink/af_netlink.c:1978 ____sys_recvmsg+0x162/0x2f0 ___sys_recvmsg net/socket.c:2674 [inline] __sys_recvmsg+0x209/0x3f0 net/socket.c:2704 __do_sys_recvmsg net/socket.c:2714 [inline] __se_sys_recvmsg net/socket.c:2711 [inline] __x64_sys_recvmsg+0x42/0x50 net/socket.c:2711 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae value changed: 0xffff -> 0x0000 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 32005 Comm: syz-executor.4 Not tainted 5.18.0-rc1-syzkaller-00328-ge1f700eb-dirty #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Link: https://lore.kernel.org/r/20220505161946.2867638-1-eric.dumazet@gmail.comSigned-off-by:
-
Lokesh Dhoundiyal authored
kmemleak reports the following when routing multicast traffic over an ipsec tunnel. Kmemleak output: unreferenced object 0x8000000044bebb00 (size 256): comm "softirq", pid 0, jiffies 4294985356 (age 126.810s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 80 00 00 00 05 13 74 80 ..............t. 80 00 00 00 04 9b bf f9 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000f83947e0>] __kmalloc+0x1e8/0x300 [<00000000b7ed8dca>] metadata_dst_alloc+0x24/0x58 [<0000000081d32c20>] __ipgre_rcv+0x100/0x2b8 [<00000000824f6cf1>] gre_rcv+0x178/0x540 [<00000000ccd4e162>] gre_rcv+0x7c/0xd8 [<00000000c024b148>] ip_protocol_deliver_rcu+0x124/0x350 [<000000006a483377>] ip_local_deliver_finish+0x54/0x68 [<00000000d9271b3a>] ip_local_deliver+0x128/0x168 [<00000000bd4968ae>] xfrm_trans_reinject+0xb8/0xf8 [<0000000071672a19>] tasklet_action_common.isra.16+0xc4/0x1b0 [<0000000062e9c336>] __do_softirq+0x1fc/0x3e0 [<00000000013d7914>] irq_exit+0xc4/0xe0 [<00000000a4d73e90>] plat_irq_dispatch+0x7c/0x108 [<000000000751eb8e>] handle_int+0x16c/0x178 [<000000001668023b>] _raw_spin_unlock_irqrestore+0x1c/0x28 The metadata dst is leaked when ip_route_input_mc() updates the dst for the skb. Commit f38a9eb1 ("dst: Metadata destinations") correctly handled dropping the dst in ip_route_input_slow() but missed the multicast case which is handled by ip_route_input_mc(). Drop the dst in ip_route_input_mc() avoiding the leak. Fixes: f38a9eb1 ("dst: Metadata destinations") Signed-off-by:Lokesh Dhoundiyal <lokesh.dhoundiyal@alliedtelesis.co.nz> Signed-off-by:
Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by:
David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20220505020017.3111846-1-chris.packham@alliedtelesis.co.nzSigned-off-by:
-
