The following dtc warning is seen when building with W=1:

arch/arm/boot/dts/imx6qdl-gw553x.dtsi:65.12-110.4: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

Remove the unneeded #address-cells/#size-cells properties to fix the issue.

Fixes: 64bf0a0a ("ARM: dts: imx6qdl-gw: add Gateworks System Controller support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add audio sound card node, which depends on codec node,
SSI node, audmux node.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Headphone detection is triggered by GPIO, then driver can
switch between speaker and headphone.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Headphone detection is triggered by GPIO, then driver can
switch between speaker and headphone.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The property "fsl,spi-num-chipselects" is gone since commit 790739c4
("dt-bindings: spi: Convert imx cspi to json-schema").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8ae ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd:

[    4.854337] m25p80@0 enforce active low on chipselect handle

Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.

The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:

 * SPI children have active low chip selects
 * by default. This can be specified negatively
 * by just omitting "spi-cs-high" in the
 * device node, or actively by tagging on
 * GPIO_ACTIVE_LOW as flag in the device
 * tree. If the line is simultaneously
 * tagged as active low in the device tree
 * and has the "spi-cs-high" set, we get a
 * conflict and the "spi-cs-high" flag will
 * take precedence.

To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the reference manual of the i.MX25 the function name for
the GPT capture input is called CAPIN1. So fix the names to follow the
same naming scheme as used for the other pads and functions. Also add
one missing pad function.

There are no mainline users that needs adaption.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the reg property to each channel node.  This update is
to accommodate the multicolor framework.  In addition to the
accommodation this allows the LEDs to be placed on any channel
and allow designs to skip channels as opposed to requiring
sequential order.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Pengutronix Kernel Team <kernel@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds missing interrupt support for the internal Marvell
switch, so that the kernel does not have to keep polling the
PHYs on the bit-banged MDIO bus all the time.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add "DMIC" rounting, headphone and microphone detect gpio for sound
card, then output sound can switch between headphone and speaker.
input sound can switch between DMIC and AMIC.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

I used the i.MX25 Reference Manual (Rev 2 01/2011) as source for these
additions and fixes.

No mainline dts is affected by the fixes (nor obviously by the
additions).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

OLED display consist of an OLED panel and a display controller.
The displays that were used on yapp4 platform were based on a SSD1305
controller. These displays are now discontinued and we need to add
support for a replacement.

The new display is based on SSD1309 controller and requires slightly
different configuration (mirror + segment offset).  We want to support
both display types so it does no matter which one was used on the assembly
line. Hence the displays are placed at different I2C addresses.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add devicetree for new variant of the Y Soft IOT appliance.
The board is based on Hydra with the following changes:

 - faster SoC (1GHz), 4GB RAM and 64GB eMMC
 - removed miniPCIe
 - removed Audio jack
 - removed uSD slot
 - removed RJ10 serial
 - HDMI replaced by USB host
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Change i.MX SoCs nand node name from "gpmi-nand" to "nand-controller" to
be compliant with yaml schema, it requires the nodename to be
"nand-controller".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Change i.MX27 nand node name from "nand" to "nand-controller" to
be compliant with yaml schema, it requires the nodename to be
"nand-controller".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add aliases for ethernet switch ports to allow bootloader to fix
MAC addresses to the ones stored in onboard configuration EEPROM.

Ursa has only one ethernet port populated (eth2) so alias for
the first port has to be removed on this board.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In preparation for an update of the TQ-Systems TQMa7x/MBa7x DTS, add the
QSPI controller to imx7s.dtsi.
Based-on-patch-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Configure the SAI device node, configure audio clock
and pinctrl.

Enable the audio sound card, which use the SAI1 and
wm8960, and enable headphone detection.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device trees for TQMa6S, TQMa6Q, and TQMa6QP embedded modules.
The A and B SoM variants are for hardware revisions that differ in
how the I2C devices are connected. For details, see [1].

This is a combination of the patches
  "arm: dt: imx6qdl: add tqma6[qdl] som on mba6 mainboard",
  "arm: dt: tqma6: add spi with spi nor flash on SOM",
  "arm: dt: add basic support for tqma6qp on mba6", and
  "arm: dt: imx6qdl-tqma6: use generic jedec,spi-nor"
from the TQMa6x BSP, with the MBa6 specific parts removed.

[1] https://support.tq-group.com/en/arm/tqma6x/linux/ptxdist/overviewSigned-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
[bst@pengutronix.de: remove unnecessary container node in the iomuxc
 node]
Signed-off-by: Bastian Krause <bst@pengutronix.de>
[p.zabel@pengutronix.de: merged patches from TQMa6x BSP REV.0114,
 separated MBa6 DTs, fixed checkpatch and dtbs_check warnings,
 added no-sd(io) properties to eMMC, added SPDX license identifiers
 and commit message]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Disable Ethernet switch reset GPIO with ZII platforms that have it
enabled.  HW switch reset results in a reset of the copper PHYs
inside of the switch.  We want to avoid this reset of the copper PHYs
in the switch as this results in unnecessary broader network disruption on
a soft reboot of the application processor.

With the HW GPIO removed, the switch driver still performs a soft reset of
the switch core which has been shown to sufficiently meet our needs with
other ZII platforms that do not have the HW switch reset GPIO defined.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the reset-gpio property, and enable PCIe on iMX6QP SABREAUTO board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add node for the RNGB block.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add node for the RNGB block.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

rng DT node was added without a compatible string.

i.MX driver for RNGC (drivers/char/hw_random/imx-rngc.c) also claims
support for RNGB, and is currently used for i.MX25.

Let's use this driver also for RNGB block in i.MX6SL.

Fixes: e29fe21c ("ARM: dts: add device tree source for imx6sl SoC")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull io_uring fixes from Jens Axboe:
 "A few differerent things in here.

  Seems like syzbot got some more io_uring bits wired up, and we got a
  handful of reports and the associated fixes are in here.

  General fixes too, and a lot of them marked for stable.

  Lastly, a bit of fallout from the async buffered reads, where we now
  more easily trigger short reads. Some applications don't really like
  that, so the io_read() code now handles short reads internally, and
  got a cleanup along the way so that it's now easier to read (and
  documented). We're now passing tests that failed before"

* tag 'io_uring-5.9-2020-08-15' of git://git.kernel.dk/linux-block:
  io_uring: short circuit -EAGAIN for blocking read attempt
  io_uring: sanitize double poll handling
  io_uring: internally retry short reads
  io_uring: retain iov_iter state over io_read/io_write calls
  task_work: only grab task signal lock when needed
  io_uring: enable lookup of links holding inflight files
  io_uring: fail poll arm on queue proc failure
  io_uring: hold 'ctx' reference around task_work queue + execute
  fs: RWF_NOWAIT should imply IOCB_NOIO
  io_uring: defer file table grabbing request cleanup for locked requests
  io_uring: add missing REQ_F_COMP_LOCKED for nested requests
  io_uring: fix recursive completion locking on oveflow flush
  io_uring: use TWA_SIGNAL for task_work uncondtionally
  io_uring: account locked memory before potential error case
  io_uring: set ctx sq/cq entry count earlier
  io_uring: Fix NULL pointer dereference in loop_rw_iter()
  io_uring: add comments on how the async buffered read retry works
  io_uring: io_async_buf_func() need not test page bit

Commit 1355c31e ("asm-generic: pgalloc: provide generic pmd_alloc_one()
and pmd_free_one()") converted parisc to use generic version of
pmd_alloc_one() but it missed the fact that parisc uses order-1 pages for
PMD.

Restore the original version of pmd_alloc_one() for parisc, just use
GFP_PGTABLE_KERNEL that implies __GFP_ZERO instead of GFP_KERNEL and
memset.

Fixes: 1355c31e ("asm-generic: pgalloc: provide generic pmd_alloc_one() and pmd_free_one()")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lkml.kernel.org/r/9f2b5ebd-e4a4-0fa1-6cd3-4b9f6892d1ad@linux.eeSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull block fixes from Jens Axboe:
 "A few fixes on the block side of things:

   - Discard granularity fix (Coly)

   - rnbd cleanups (Guoqing)

   - md error handling fix (Dan)

   - md sysfs fix (Junxiao)

   - Fix flush request accounting, which caused an IO slowdown for some
     configurations (Ming)

   - Properly propagate loop flag for partition scanning (Lennart)"

* tag 'block-5.9-2020-08-14' of git://git.kernel.dk/linux-block:
  block: fix double account of flush request's driver tag
  loop: unset GENHD_FL_NO_PART_SCAN on LOOP_CONFIGURE
  rnbd: no need to set bi_end_io in rnbd_bio_map_kern
  rnbd: remove rnbd_dev_submit_io
  md-cluster: Fix potential error pointer dereference in resize_bitmaps()
  block: check queue's limits.discard_granularity in __blkdev_issue_discard()
  md: get sysfs entry after redundancy attr group create

Pull RISC-V fix from Palmer Dabbelt:
 "I collected a single fix during the merge window: we managed to break
  the early trap setup on !MMU, this fixes it"

* tag 'riscv-for-linus-5.9-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Setup exception vector for nommu platform

Pull arch/sh updates from Rich Felker:
 "Cleanup, SECCOMP_FILTER support, message printing fixes, and other
  changes to arch/sh"

* tag 'sh-for-5.9' of git://git.libc.org/linux-sh: (34 commits)
  sh: landisk: Add missing initialization of sh_io_port_base
  sh: bring syscall_set_return_value in line with other architectures
  sh: Add SECCOMP_FILTER
  sh: Rearrange blocks in entry-common.S
  sh: switch to copy_thread_tls()
  sh: use the generic dma coherent remap allocator
  sh: don't allow non-coherent DMA for NOMMU
  dma-mapping: consolidate the NO_DMA definition in kernel/dma/Kconfig
  sh: unexport register_trapped_io and match_trapped_io_handler
  sh: don't include <asm/io_trapped.h> in <asm/io.h>
  sh: move the ioremap implementation out of line
  sh: move ioremap_fixed details out of <asm/io.h>
  sh: remove __KERNEL__ ifdefs from non-UAPI headers
  sh: sort the selects for SUPERH alphabetically
  sh: remove -Werror from Makefiles
  sh: Replace HTTP links with HTTPS ones
  arch/sh/configs: remove obsolete CONFIG_SOC_CAMERA*
  sh: stacktrace: Remove stacktrace_ops.stack()
  sh: machvec: Modernize printing of kernel messages
  sh: pci: Modernize printing of kernel messages
  ...

One case was missed in the short IO retry handling, and that's hitting
-EAGAIN on a blocking attempt read (eg from io-wq context). This is a
problem on sockets that are marked as non-blocking when created, they
don't carry any REQ_F_NOWAIT information to help us terminate them
instead of perpetually retrying.

Fixes: 227c0c96 ("io_uring: internally retry short reads")
Signed-off-by: Jens Axboe <axboe@kernel.dk>

There's a bit of confusion on the matching pairs of poll vs double poll,
depending on if the request is a pure poll (IORING_OP_POLL_ADD) or
poll driven retry.

Add io_poll_get_double() that returns the double poll waitqueue, if any,
and io_poll_get_single() that returns the original poll waitqueue. With
that, remove the argument to io_poll_remove_double().

Finally ensure that wait->private is cleared once the double poll handler
has run, so that remove knows it's already been seen.

Cc: stable@vger.kernel.org # v5.8
Reported-by: syzbot+7f617d4a9369028b8a2c@syzkaller.appspotmail.com
Fixes: 18bceab1 ("io_uring: allow POLL_ADD with double poll_wait() users")
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull more perf tools updates from Arnaldo Carvalho de Melo:
 "Fixes:
   - Fixes for 'perf bench numa'.

   - Always memset source before memcpy in 'perf bench mem'.

   - Quote CC and CXX for their arguments to fix build in environments
     using those variables to pass more than just the compiler names.

   - Fix module symbol processing, addressing regression detected via
     "perf test".

   - Allow multiple probes in record+script_probe_vfs_getname.sh 'perf
     test' entry.

  Improvements:
   - Add script to autogenerate socket family name id->string table from
     copy of kernel header, used so far in 'perf trace'.

   - 'perf ftrace' improvements to provide similar options for this
     utility so that one can go from 'perf record', 'perf trace', etc to
     'perf ftrace' just by changing the name of the subcommand.

   - Prefer new "sched:sched_waking" trace event when it exists in 'perf
     sched' post processing.

   - Update POWER9 metrics to utilize other metrics.

   - Fall back to querying debuginfod if debuginfo not found locally.

  Miscellaneous:
   - Sync various kvm headers with kernel sources"

* tag 'perf-tools-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (40 commits)
  perf ftrace: Make option description initials all capital letters
  perf build-ids: Fall back to debuginfod query if debuginfo not found
  perf bench numa: Remove dead code in parse_nodes_opt()
  perf stat: Update POWER9 metrics to utilize other metrics
  perf ftrace: Add change log
  perf: ftrace: Add set_tracing_options() to set all trace options
  perf ftrace: Add option --tid to filter by thread id
  perf ftrace: Add option -D/--delay to delay tracing
  perf: ftrace: Allow set graph depth by '--graph-opts'
  perf ftrace: Add support for trace option tracing_thresh
  perf ftrace: Add option 'verbose' to show more info for graph tracer
  perf ftrace: Add support for tracing option 'irq-info'
  perf ftrace: Add support for trace option funcgraph-irqs
  perf ftrace: Add support for trace option sleep-time
  perf ftrace: Add support for tracing option 'func_stack_trace'
  perf tools: Add general function to parse sublevel options
  perf ftrace: Add option '--inherit' to trace children processes
  perf ftrace: Show trace column header
  perf ftrace: Add option '-m/--buffer-size' to set per-cpu buffer size
  perf ftrace: Factor out function write_tracing_file_int()
  ...

Pull x86 fixes from Ingo Molnar:
 "Misc fixes and small updates all around the place:

   - Fix mitigation state sysfs output

   - Fix an FPU xstate/sxave code assumption bug triggered by
     Architectural LBR support

   - Fix Lightning Mountain SoC TSC frequency enumeration bug

   - Fix kexec debug output

   - Fix kexec memory range assumption bug

   - Fix a boundary condition in the crash kernel code

   - Optimize porgatory.ro generation a bit

   - Enable ACRN guests to use X2APIC mode

   - Reduce a __text_poke() IRQs-off critical section for the benefit of
     PREEMPT_RT"

* tag 'x86-urgent-2020-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/alternatives: Acquire pte lock with interrupts enabled
  x86/bugs/multihit: Fix mitigation reporting when VMX is not in use
  x86/fpu/xstate: Fix an xstate size check warning with architectural LBRs
  x86/purgatory: Don't generate debug info for purgatory.ro
  x86/tsr: Fix tsc frequency enumeration bug on Lightning Mountain SoC
  kexec_file: Correctly output debugging information for the PT_LOAD ELF header
  kexec: Improve & fix crash_exclude_mem_range() to handle overlapping ranges
  x86/crash: Correct the address boundary of function parameters
  x86/acrn: Remove redundant chars from ACRN signature
  x86/acrn: Allow ACRN guest to use X2APIC mode

Pull scheduler fixes from Ingo Molnar:
 "Two fixes: fix a new tracepoint's output value, and fix the formatting
  of show-state syslog printouts"

* tag 'sched-urgent-2020-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Fix the alignment of the show-state debug output
  sched: Fix use of count for nr_running tracepoint

Pull perf fixes from Ingo Molnar:
 "Misc fixes, an expansion of perf syscall access to CAP_PERFMON
  privileged tools, plus a RAPL HW-enablement for Intel SPR platforms"

* tag 'perf-urgent-2020-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/rapl: Add support for Intel SPR platform
  perf/x86/rapl: Support multiple RAPL unit quirks
  perf/x86/rapl: Fix missing psys sysfs attributes
  hw_breakpoint: Remove unused __register_perf_hw_breakpoint() declaration
  kprobes: Remove show_registers() function prototype
  perf/core: Take over CAP_SYS_PTRACE creds to CAP_PERFMON capability

Pull locking fixlets from Ingo Molnar:
 "A documentation fix and a 'fallthrough' macro update"

* tag 'locking-urgent-2020-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex: Convert to use the preferred 'fallthrough' macro
  Documentation/locking/locktypes: Fix a typo

Pull 9p updates from Dominique Martinet:

 - some code cleanup

 - a couple of static analysis fixes

 - setattr: try to pick a fid associated with the file rather than the
   dentry, which might sometimes matter

* tag '9p-for-5.9-rc1' of git://github.com/martinetd/linux:
  9p: Remove unneeded cast from memory allocation
  9p: remove unused code in 9p
  net/9p: Fix sparse endian warning in trans_fd.c
  9p: Fix memory leak in v9fs_mount
  9p: retrieve fid from file when file instance exist.

Pull cifs fixes from Steve French:
 "Three small cifs/smb3 fixes, one for stable fixing mkdir path with
  the 'idsfromsid' mount option"

* tag '5.9-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  SMB3: Fix mkdir when idsfromsid configured on mount
  cifs: Convert to use the fallthrough macro
  cifs: Fix an error pointer dereference in cifs_mount()

Pull NFS client updates from Trond Myklebust:
 "Stable fixes:
   - pNFS: Don't return layout segments that are being used for I/O
   - pNFS: Don't move layout segments off the active list when being used for I/O

  Features:
   - NFS: Add support for user xattrs through the NFSv4.2 protocol
   - NFS: Allow applications to speed up readdir+statx() using AT_STATX_DONT_SYNC
   - NFSv4.0 allow nconnect for v4.0

  Bugfixes and cleanups:
   - nfs: ensure correct writeback errors are returned on close()
   - nfs: nfs_file_write() should check for writeback errors
   - nfs: Fix getxattr kernel panic and memory overflow
   - NFS: Fix the pNFS/flexfiles mirrored read failover code
   - SUNRPC: dont update timeout value on connection reset
   - freezer: Add unsafe versions of freezable_schedule_timeout_interruptible for NFS
   - sunrpc: destroy rpc_inode_cachep after unregister_filesystem"

* tag 'nfs-for-5.9-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (32 commits)
  NFS: Fix flexfiles read failover
  fs: nfs: delete repeated words in comments
  rpc_pipefs: convert comma to semicolon
  nfs: Fix getxattr kernel panic and memory overflow
  NFS: Don't return layout segments that are in use
  NFS: Don't move layouts to plh_return_segs list while in use
  NFS: Add layout segment info to pnfs read/write/commit tracepoints
  NFS: Add tracepoints for layouterror and layoutstats.
  NFS: Report the stateid + status in trace_nfs4_layoutreturn_on_close()
  SUNRPC dont update timeout value on connection reset
  nfs: nfs_file_write() should check for writeback errors
  nfs: ensure correct writeback errors are returned on close()
  NFSv4.2: xattr cache: get rid of cache discard work queue
  NFS: remove redundant initialization of variable result
  NFSv4.0 allow nconnect for v4.0
  freezer: Add unsafe versions of freezable_schedule_timeout_interruptible for NFS
  sunrpc: destroy rpc_inode_cachep after unregister_filesystem
  NFSv4.2: add client side xattr caching.
  NFSv4.2: hook in the user extended attribute handlers
  NFSv4.2: add the extended attribute proc functions.
  ...