Not all platforms have an RTC, and rather than trying to force one into
each, it's much easier to just set a fixed time. This is necessary
because WireGuard's latest handshakes parameter is returned in wallclock
time, and if the system time isn't set, and the system is really fast,
then this returns 0, which trips the test.

Turning this on requires setting CONFIG_COMPAT_32BIT_TIME=y, as musl
doesn't support settimeofday without it.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

66e4c8d9 ("net: warn if transport header was not set") added
a check that triggers a warning in r8169, see [0].

The commit referenced in the Fixes tag refers to the change from
which the patch applies cleanly, there's nothing wrong with this
commit. It seems the actual issue (not bug, because the warning
is harmless here) was introduced with bdfa4ed6
("r8169: use Giant Send").

[0] https://bugzilla.kernel.org/show_bug.cgi?id=216157

Fixes: 8d520b4d ("r8169: work around RTL8125 UDP hw bug")
Reported-by: Erhard F. <erhard_f@mailbox.org>
Tested-by: Erhard F. <erhard_f@mailbox.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/1b2c2b29-3dc0-f7b6-5694-97ec526d51a0@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There are UAF bugs caused by rose_t0timer_expiry(). The
root cause is that del_timer() could not stop the timer
handler that is running and there is no synchronization.
One of the race conditions is shown below:

    (thread 1)             |        (thread 2)
                           | rose_device_event
                           |   rose_rt_device_down
                           |     rose_remove_neigh
rose_t0timer_expiry        |       rose_stop_t0timer(rose_neigh)
  ...                      |         del_timer(&neigh->t0timer)
                           |         kfree(rose_neigh) //[1]FREE
  neigh->dce_mode //[2]USE |

The rose_neigh is deallocated in position [1] and use in
position [2].

The crash trace triggered by POC is like below:

BUG: KASAN: use-after-free in expire_timers+0x144/0x320
Write of size 8 at addr ffff888009b19658 by task swapper/0/0
...
Call Trace:
 <IRQ>
 dump_stack_lvl+0xbf/0xee
 print_address_description+0x7b/0x440
 print_report+0x101/0x230
 ? expire_timers+0x144/0x320
 kasan_report+0xed/0x120
 ? expire_timers+0x144/0x320
 expire_timers+0x144/0x320
 __run_timers+0x3ff/0x4d0
 run_timer_softirq+0x41/0x80
 __do_softirq+0x233/0x544
 ...

This patch changes rose_stop_ftimer() and rose_stop_t0timer()
in rose_remove_neigh() to del_timer_sync() in order that the
timer handler could be finished before the resources such as
rose_neigh and so on are deallocated. As a result, the UAF
bugs could be mitigated.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220705125610.77971-1-duoming@zju.edu.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

usbnet_write_cmd_async() mixed up which buffers
need to be freed in which error case.

v2: add Fixes tag
v3: fix uninitialized buf pointer

Fixes: 877bd862 ("usbnet: introduce usbnet 3 command helpers")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220705125351.17309-1-oneukum@suse.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 284b4d93.
When using TLS device offload and coming from tls_device_reencrypt()
flow, -EBADMSG error in tls_do_decryption() should not be counted
towards the TLSTlsDecryptError counter.

Move the counter increase back to the decrypt_internal() call site in
decrypt_skb_update().
This also fixes an issue where:
	if (n_sgin < 1)
		return -EBADMSG;

Errors in decrypt_internal() were not counted after the cited patch.

Fixes: 284b4d93 ("tls: rx: move counting TlsDecryptErrors for sync")
Cc: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: Path manager fixes for 5.19

The MPTCP userspace path manager is new in 5.19, and these patches fix
some issues in that new code.

Patches 1-3 fix path manager locking issues.

Patches 4 and 5 allow userspace path managers to change priority of
established subflows using the existing MPTCP_PM_CMD_SET_FLAGS generic
netlink command. Includes corresponding self test update.

Patches 6 and 7 fix accounting of available endpoint IDs and the
MPTCP_MIB_RMSUBFLOW counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch increases MPTCP_MIB_RMSUBFLOW mib counter in userspace pm
destroy subflow function mptcp_nl_cmd_sf_destroy() when removing subflow.

Fixes: 702c2f64 ("mptcp: netlink: allow userspace-driven subflow establishment")
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In mptcp_pm_nl_rm_addr_or_subflow() we always mark as available
the id corresponding to the just removed address.

The used bitmap actually tracks only the local IDs: we must
restrict the operation when a (local) subflow is removed.

Fixes: a88c9e49 ("mptcp: do not block subflows creation on errors")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change updates the testing sample (pm_nl_ctl) to exercise
the updated MPTCP_PM_CMD_SET_FLAGS command for userspace PMs to
issue MP_PRIO signals over the selected subflow.

E.g. ./pm_nl_ctl set 10.0.1.2 port 47234 flags backup token 823274047 rip 10.0.1.1 rport 50003

userspace_pm.sh has a new selftest that invokes this command.

Fixes: 259a834f ("selftests: mptcp: functional tests for the userspace PM type")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Kishen Maloor <kishen.maloor@intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change updates MPTCP_PM_CMD_SET_FLAGS to allow userspace PMs
to issue MP_PRIO signals over a specific subflow selected by
the connection token, local and remote address+port.

Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/286
Fixes: 702c2f64 ("mptcp: netlink: allow userspace-driven subflow establishment")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Kishen Maloor <kishen.maloor@intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When setting up a subflow's flags for sending MP_PRIO MPTCP options, the
subflow socket lock was not held while reading and modifying several
struct members that are also read and modified in mptcp_write_options().

Acquire the subflow socket lock earlier and send the MP_PRIO ACK with
that lock already acquired. Add a new variant of the
mptcp_subflow_send_ack() helper to use with the subflow lock held.

Fixes: 06706542 ("mptcp: add the outgoing MP_PRIO support")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The in-kernel path manager code for changing subflow flags acquired both
the msk socket lock and the PM lock when possibly changing the "backup"
and "fullmesh" flags. mptcp_pm_nl_mp_prio_send_ack() does not access
anything protected by the PM lock, and it must release and reacquire
the PM lock.

By pushing the PM lock to where it is needed in mptcp_pm_nl_fullmesh(),
the lock is only acquired when the fullmesh flag is changed and the
backup flag code no longer has to release and reacquire the PM lock. The
change in locking context requires the MIB update to be modified - move
that to a better location instead.

This change also makes it possible to call
mptcp_pm_nl_mp_prio_send_ack() for the userspace PM commands without
manipulating the in-kernel PM lock.

Fixes: 0f9f696a ("mptcp: add set_flags command in PM netlink")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The user-space PM subflow removal path uses a couple of helpers
that must be called under the msk socket lock and the current
code lacks such requirement.

Change the existing lock scope so that the relevant code is under
its protection.

Fixes: 702c2f64 ("mptcp: netlink: allow userspace-driven subflow establishment")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/287Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vlad Buslov says:

====================
net: Fix police 'continue' action offload

TC act_police with 'continue' action had been supported by mlx5 matchall
classifier offload implementation for some time. However, 'continue' was
assumed implicitly and recently got broken in multiple places. Fix it in
both TC hardware offload validation code and mlx5 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Referenced commit prepared the code for upcoming extension that allows mlx5
to offload police action attached to flower classifier. However, with
regard to existing matchall classifier offload validation should be
reversed as FLOW_ACTION_CONTINUE is the only supported notexceed police
action type. Fix the problem by allowing FLOW_ACTION_CONTINUE for police
action and extend scan_tc_matchall_fdb_actions() to only allow such actions
with matchall classifier.

Fixes: d97b4b10 ("flow_offload: reject offload for all drivers with invalid police parameters")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Offloading police with action TC_ACT_UNSPEC was erroneously disabled even
though it was supported by mlx5 matchall offload implementation, which
didn't verify the action type but instead assumed that any single police
action attached to matchall classifier is a 'continue' action. Lack of
action type check made it non-obvious what mlx5 matchall implementation
actually supports and caused implementers and reviewers of referenced
commits to disallow it as a part of improved validation code.

Fixes: b8cd5831 ("net: flow_offload: add tc police action parameters")
Fixes: b50e462b ("net/sched: act_police: Add extack messages for offload failure")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of counting the child nodes in the device tree, hardcode the
number of ports in the driver itself.  The counting won't work at all
if an ethernet port is marked as disabled, e.g. because it is not
connected on the board at all.

It turns out that the LAN9662 and LAN9668 use the same switching IP
with the same synthesis parameters. The only difference is that the
output ports are not connected. Thus, we can just hardcode the
number of physical ports to 8.

Fixes: db8bcaad ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220704153654.1167886-1-michael@walle.ccSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Luiz Augusto von Dentz says:

====================
bluetooth pull request for net:

 - Fix deadlock when powering on.

* tag 'for-net-2022-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
  Bluetooth: core: Fix deadlock on hci_power_on_sync.
====================

Link: https://lore.kernel.org/r/20220705202700.1689796-1-luiz.dentz@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

`cancel_work_sync(&hdev->power_on)` was moved to hci_dev_close_sync in
commit [1] to ensure that power_on work is canceled after HCI interface
down.

But, in certain cases power_on work function may call hci_dev_close_sync
itself: hci_power_on -> hci_dev_do_close -> hci_dev_close_sync ->
cancel_work_sync(&hdev->power_on), causing deadlock. In particular, this
happens when device is rfkilled on boot. To avoid deadlock, move
power_on work canceling out of hci_dev_do_close/hci_dev_close_sync.

Deadlock introduced by commit [1] was reported in [2,3] as broken
suspend. Suspend did not work because `hdev->req_lock` held as result of
`power_on` work deadlock. In fact, other BT features were not working.
It was not observed when testing [1] since it was verified without
rfkill in place.

NOTE: It is not needed to cancel power_on work from other places where
hci_dev_do_close/hci_dev_close_sync is called in case:
* Requests were serialized due to `hdev->req_workqueue`. The power_on
work is first in that workqueue.
* hci_rfkill_set_block which won't close device anyway until HCI_SETUP
is on.
* hci_sock_release which runs after hci_sock_bind which ensures
HCI_SETUP was cleared.

As result, behaviour is the same as in pre-dd06ed7 commit, except
power_on work cancel added to hci_dev_close.

[1]: commit ff7f2926 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
[2]: https://lore.kernel.org/lkml/20220614181706.26513-1-max.oss.09@gmail.com/
[2]: https://lore.kernel.org/lkml/1236061d-95dd-c3ad-a38f-2dae7aae51ef@o2.pl/

Fixes: ff7f2926 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com>
Reported-by: Max Krummenacher <max.krummenacher@toradex.com>
Reported-by: Mateusz Jonczyk <mat.jonczyk@o2.pl>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Vladimir Oltean says:

====================
Fix bridge_vlan_aware.sh and bridge_vlan_unaware.sh with IFF_UNICAST_FLT

Make sure that h1 and h2 don't drop packets with a random MAC DA, which
otherwise confuses these selftests. Also, fix an incorrect error message
found during those failures.
====================

Link: https://lore.kernel.org/r/20220703073626.937785-1-vladimir.oltean@nxp.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When packets are not received, they aren't received on $host1_if, so the
message talking about the second host not receiving them is incorrect.
Fix it.

Fixes: d4deb014 ("selftests: forwarding: Add a test for FDB learning")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The first host interface has by default no interest in receiving packets
MAC DA de:ad:be:ef:13:37, so it might drop them before they hit the tc
filter and this might confuse the selftest.

Enable promiscuous mode such that the filter properly counts received
packets.

Fixes: d4deb014 ("selftests: forwarding: Add a test for FDB learning")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

As mentioned in the blamed commit, flood_unicast_test() works by
checking the match count on a tc filter placed on the receiving
interface.

But the second host interface (host2_if) has no interest in receiving a
packet with MAC DA de:ad:be:ef:13:37, so its RX filter drops it even
before the ingress tc filter gets to be executed. So we will incorrectly
get the message "Packet was not flooded when should", when in fact, the
packet was flooded as expected but dropped due to an unrelated reason,
at some other layer on the receiving side.

Force h2 to accept this packet by temporarily placing it in promiscuous
mode. Alternatively we could either deliver to its MAC address or use
tcpdump_start, but this has the fewest complications.

This fixes the "flooding" test from bridge_vlan_aware.sh and
bridge_vlan_unaware.sh, which calls flood_test from the lib.

Fixes: 236dd50b ("selftests: forwarding: Add a test for flooded traffic")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Merge tag 'linux-can-fixes-for-5.19-20220704' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
can 2022-07-04

The 1st patch is by Oliver Hartkopp, targets the BCM CAN protocol and
converts a costly synchronize_rcu() to call_rcu() to fix a performance
regression.

Srinivas Neeli's patch for the xilinx_can driver drops the brp limit
down to 1, as only the pre-production silicon have an issue with a brp
of 1.

The next patch is by Duy Nguyen and fixes the data transmission on
R-Car V3U SoCs in the rcar_canfd driver.

Rhett Aultman's patch fixes a DMA memory leak in the gs_usb driver.

Liang He's patch removes an extra of_node_get() in the grcan driver.

The next 2 patches are by me, target the m_can driver and fix the
timestamp handling used for peripheral devices like the tcan4x5x.

Jimmy Assarsson contributes 3 patches for the kvaser_usb driver and
fixes CAN clock and bit timing related issues.

The remaining 5 patches target the mcp251xfd driver. Thomas Kopp
contributes 2 patches to improve the workaround for broken CRC when
reading the TBC register. 3 patches by me add a missing
hrtimer_cancel() during the ndo_stop() callback, and fix the reading
of the Device ID register.

* tag 'linux-can-fixes-for-5.19-20220704' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
  can: mcp251xfd: mcp251xfd_register_get_dev_id(): fix endianness conversion
  can: mcp251xfd: mcp251xfd_register_get_dev_id(): use correct length to read dev_id
  can: mcp251xfd: mcp251xfd_stop(): add missing hrtimer_cancel()
  can: mcp251xfd: mcp251xfd_regmap_crc_read(): update workaround broken CRC on TBC register
  can: mcp251xfd: mcp251xfd_regmap_crc_read(): improve workaround handling for mcp2517fd
  can: kvaser_usb: kvaser_usb_leaf: fix bittiming limits
  can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression
  can: kvaser_usb: replace run-time checks with struct kvaser_usb_driver_info
  can: m_can: m_can_{read_fifo,echo_tx_event}(): shift timestamp to full 32 bits
  can: m_can: m_can_chip_config(): actually enable internal timestamping
  can: grcan: grcan_probe(): remove extra of_node_get()
  can: gs_usb: gs_usb_open/close(): fix memory leak
  can: rcar_canfd: Fix data transmission failed on R-Car V3U
  Revert "can: xilinx_can: Limit CANFD brp to 2"
  can: bcm: use call_rcu() instead of costly synchronize_rcu()
====================

Link: https://lore.kernel.org/r/20220704122613.1551119-1-mkl@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In mcp251xfd_register_get_dev_id() the device ID register is read with
handcrafted SPI transfers. As all registers, this register is in
little endian. Further it is not naturally aligned in struct
mcp251xfd_map_buf_nocrc::data. However after the transfer the register
content is converted from big endian to CPU endianness not taking care
of being unaligned.

Fix the conversion by converting from little endian to CPU endianness
taking the unaligned source into account.

Side note: So far the register content is 0x0 on all mcp251xfd
compatible chips, and is only used for an informative printk.

Link: https://lore.kernel.org/all/20220627092859.809042-1-mkl@pengutronix.de
Fixes: 55e5b97f ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The device ID register is 32 bits wide. The driver uses incorrectly
the size of a pointer to a u32 to calculate the length of the SPI
transfer. This results in a read of 2 registers on 64 bit platforms.
This is no problem on the Linux side, as the RX buffer of the SPI
transfer is large enough. In the mpc251xfd chip this results in the
read of an undocumented register. So far no problems were observed.

Fix the length of the SPI transfer to read the device ID register
only.

Link: https://lore.kernel.org/all/20220616094914.244440-1-mkl@pengutronix.de
Fixes: 55e5b97f ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In commit 169d00a2 ("can: mcp251xfd: add TX IRQ coalescing
support") software based TX coalescing was added to the driver. The
key idea is to keep the TX complete IRQ disabled for some time after
processing it and re-enable later by a hrtimer. When bringing the
interface down, this timer has to be stopped.

Add the missing hrtimer_cancel() of the tx_irq_time hrtimer to
mcp251xfd_stop().

Link: https://lore.kernel.org/all/20220620143942.891811-1-mkl@pengutronix.de
Fixes: 169d00a2 ("can: mcp251xfd: add TX IRQ coalescing support")
Cc: stable@vger.kernel.org # v5.18
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit
c7eb923c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.

- If a CRC read error on the TBC register is detected and the first
  byte is 0x00 or 0x80, the most significant bit of the first byte is
  flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
  For now we assume transferred data was OK.

New investigations and simulations indicate that the CRC send by the
device is calculated on correct data, and the data is incorrectly
received by the SPI host controller.

Use flipped instead of original data and update workaround description
in mcp251xfd_regmap_crc_read().

[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"

Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com
Fixes: c7eb923c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit
c7eb923c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.

- If a CRC read error on the TBC register is detected and the first
  byte is 0x00 or 0x80, the most significant bit of the first byte is
  flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
  For now we assume transferred data was OK.

Measurements on the mcp2517fd show that the workaround is applicable
not only of the lowest byte is 0x00 or 0x80, but also if 3 least
significant bits are set.

Update check on 1st data byte and workaround description accordingly.

[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"

Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com
Fixes: c7eb923c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register")
Cc: stable@vger.kernel.org
Reported-by: Pavel Modilaynen <pavel.modilaynen@volvocars.com>
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Use correct bittiming limits depending on device. For devices based on
USBcanII, Leaf M32C or Leaf i.MX28.

Fixes: 080f40a6 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Fixes: b4f20130 ("can: kvaser_usb: add support for Kvaser Leaf v2 and usb mini PCIe")
Fixes: f5d4abea ("can: kvaser_usb: Add support for the USBcan-II family")
Link: https://lore.kernel.org/all/20220603083820.800246-4-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: remove stray netlink.h include]
[mkl: keep struct can_bittiming_const kvaser_usb_flexc_bittiming_const in kvaser_usb_hydra.c]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The firmware of M32C based Leaf devices expects bittiming parameters
calculated for 16MHz clock. Since we use the actual clock frequency of
the device, the device may end up with wrong bittiming parameters,
depending on user requested parameters.

This regression affects M32C based Leaf devices with non-16MHz clock.

Fixes: fb12797a ("can: kvaser_usb: get CAN clock frequency from device")
Link: https://lore.kernel.org/all/20220603083820.800246-3-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Unify and move compile-time known information into new struct
kvaser_usb_driver_info, in favor of run-time checks.

All Kvaser USBcanII supports listen-only mode and error counter
reporting.

Link: https://lore.kernel.org/all/20220603083820.800246-2-extja@kvaser.comSuggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: move struct kvaser_usb_driver_info into kvaser_usb_core.c]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

During a reset, there may have been transmits in flight that are no
longer valid and cannot be fulfilled.  Resetting and clearing the
queues is insufficient; each skb also needs to be explicitly freed
so that upper levels are not left waiting for confirmation of a
transmit that will never happen.  If this happens frequently enough,
the apparent backlog will cause TCP to begin "congestion control"
unnecessarily, culminating in permanently decreased throughput.

Fixes: d7c0ef36 ("ibmvnic: Free and re-allocate scrqs when tx/rx scrqs change")
Tested-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Rick Lindsley <ricklind@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 1be37d3b ("can: m_can: fix periph RX path: use
rx-offload to ensure skbs are sent from softirq context") the RX path
for peripheral devices was switched to RX-offload.

Received CAN frames are pushed to RX-offload together with a
timestamp. RX-offload is designed to handle overflows of the timestamp
correctly, if 32 bit timestamps are provided.

The timestamps of m_can core are only 16 bits wide. So this patch
shifts them to full 32 bit before passing them to RX-offload.

Link: https://lore.kernel.org/all/20220612211410.4081390-1-mkl@pengutronix.de
Fixes: 1be37d3b ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In commit df06fd67 ("can: m_can: m_can_chip_config(): enable and
configure internal timestamps") the timestamping in the m_can core
should be enabled. In peripheral mode, the RX'ed CAN frames, TX
compete frames and error events are sorted by the timestamp.

The above mentioned commit however forgot to enable the timestamping.
Add the missing bits to enable the timestamp counter to the write of
the Timestamp Counter Configuration register.

Link: https://lore.kernel.org/all/20220612212708.4081756-1-mkl@pengutronix.de
Fixes: df06fd67 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In grcan_probe(), of_find_node_by_path() has already increased the
refcount. There is no need to call of_node_get() again, so remove it.

Link: https://lore.kernel.org/all/20220619070257.4067022-1-windhl@126.com
Fixes: 1e93ed26 ("can: grcan: grcan_probe(): fix broken system id check for errata workaround needs")
Cc: stable@vger.kernel.org # v5.18
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The gs_usb driver appears to suffer from a malady common to many USB
CAN adapter drivers in that it performs usb_alloc_coherent() to
allocate a number of USB request blocks (URBs) for RX, and then later
relies on usb_kill_anchored_urbs() to free them, but this doesn't
actually free them. As a result, this may be leaking DMA memory that's
been used by the driver.

This commit is an adaptation of the techniques found in the esd_usb2
driver where a similar design pattern led to a memory leak. It
explicitly frees the RX URBs and their DMA memory via a call to
usb_free_coherent(). Since the RX URBs were allocated in the
gs_can_open(), we remove them in gs_can_close() rather than in the
disconnect function as was done in esd_usb2.

For more information, see the 928150fa ("can: esd_usb2: fix memory
leak").

Link: https://lore.kernel.org/all/alpine.DEB.2.22.394.2206031547001.1630869@thelappy
Fixes: d08e973a ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

On R-Car V3U, this driver should use suitable register offset instead of
other SoCs' one. Otherwise, data transmission failed on R-Car V3U.

Fixes: 45721c40 ("can: rcar_canfd: Add support for r8a779a0 SoC")
Link: https://lore.kernel.org/all/20220704074611.957191-1-yoshihiro.shimoda.uh@renesas.comReviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This reverts commit 05ca14fd.

On early silicon engineering samples observed bit shrinking issue when
we use brp as 1. Hence updated brp_min as 2. As in production silicon
this issue is fixed, so reverting the patch.

Link: https://lore.kernel.org/all/20220609082433.1191060-2-srinivas.neeli@xilinx.comSigned-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Jakub Kicinski says:

====================
docs: netdev: document more of our rules

The patch series length limit and reverse xmas tree are not documented.
Add those, and a tl;dr section summarizing how we differ.

v2: improve the series length blurb (Andrew)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>