Configurations with multiple codecs attached to the platform are
supported but only if each from the set is different. Add new field
representing the 'Unique ID' so that codecs that share Vendor and Part
IDs can be differentiated and thus enabling support for such
configurations.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-6-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Constant 'C4_CHANNEL' does not exist on the firmware side. Value 0xC is
reserved for 'C7_1' instead.

Fixes: 580a5912 ("ASoC: Intel: avs: Declare module configuration types")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-5-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Constant 'C4_CHANNEL' does not exist on the firmware side. Value 0xC is
reserved for 'C7_1' instead.

Fixes: 04afbbbb ("ASoC: Intel: Skylake: Update the topology interface structure")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-4-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Path and its components should be accessed under lock to prevent
problems with one thread modifying them while other tries to read.

Fixes: c8c960c1 ("ASoC: Intel: avs: APL-based platforms support")
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-3-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

When changing value of kcontrol, FW module to which data should be send
needs to be found. Currently it is done in improper way, fix it. Change
function name to indicate that it looks only for volume module.

This allows to change volume during runtime, instead of only changing
init value.

Fixes: be2b81b5 ("ASoC: Intel: avs: Parse control tuples")
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-2-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

In the BE hw_params configuration, the existing code checks if any of the
existing FEs are prepared, running, paused or suspended - and skips the
configuration in those cases. This allows multiple calls of hw_params
which the ALSA state machine supports.

This check is not handled for the prepare stage, which can lead to the
same BE being prepared multiple times. This patch adds a check similar to
that of the hw_params, with the main difference being that the suspended
state is allowed: the ALSA state machine allows a transition from
suspended to prepared with hw_params skipped.

This problem was detected on Intel IPC4/SoundWire devices, where the BE
dailink .prepare stage is used to configure the SoundWire stream with a
bank switch. Multiple .prepare calls lead to conflicts with the .trigger
operation with IPC4 configurations. This problem was not detected earlier
on Intel devices, HDaudio BE dailinks detect that the link is already
prepared and skip the configuration, and for IPC3 devices there is no BE
trigger.

Link: https://github.com/thesofproject/sof/issues/7596
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230517185731.487124-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

The rt5682 driver switches its regmap to cache-only when the
device suspends and back to regular mode on resume. When the
jack detect interrupt fires rt5682_irq() schedules the jack
detect work. This can result in invalid reads from the regmap
in cache-only mode if the work runs before the device has
resumed:

[   56.245502] rt5682 9-001a: ASoC: error at soc_component_read_no_lock on rt5682.9-001a for register: [0x000000f0] -16

Disable the jack detection interrupt during suspend and
re-enable it on resume. The driver already schedules the
jack detection work on resume, so any state change during
suspend is still handled.

This is essentially the same as commit f7d00a9b ("SoC:
rt5682s: Disable jack detection interrupt during suspend")
for the rt5682s.

Cc: stable@kernel.org
Signed-off-by: Matthias Kaehlcke <mka@chromium.org
Reviewed-by: Douglas Anderson <dianders@chromium.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org
Link: https://lore.kernel.org/r/20230516164629.1.Ibf79e94b3442eecc0054d2b478779cc512d967fc@changeid
Signed-off-by: Mark Brown <broonie@kernel.org

When we run syzkaller we get below Out of Bounds error.

"KASAN: slab-out-of-bounds Read in regcache_flat_read"

Below is the backtrace of the issue:

BUG: KASAN: slab-out-of-bounds in regcache_flat_read+0x10c/0x110
Read of size 4 at addr ffffff8088fbf714 by task syz-executor.4/14144
CPU: 6 PID: 14144 Comm: syz-executor.4 Tainted: G        W
Hardware name: Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+) (DT)
Call trace:
dump_backtrace+0x0/0x4ec
show_stack+0x34/0x50
dump_stack_lvl+0xdc/0x11c
print_address_description+0x30/0x2d8
kasan_report+0x178/0x1e4
__asan_report_load4_noabort+0x44/0x50
regcache_flat_read+0x10c/0x110
regcache_read+0xf8/0x5a0
_regmap_read+0x45c/0x86c
_regmap_update_bits+0x128/0x290
regmap_update_bits_base+0xc0/0x15c
snd_soc_component_update_bits+0xa8/0x22c
snd_soc_component_write_field+0x68/0xd4
tx_macro_put_dec_enum+0x1d0/0x268
snd_ctl_elem_write+0x288/0x474

By Error checking and checking valid values issue gets rectifies.

Signed-off-by: Ravulapati Vishnu Vardhan Rao <quic_visr@quicinc.com
Link: https://lore.kernel.org/r/20230511112532.16106-1-quic_visr@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org

Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:

With additional testing with multiple links and multiple DAI types, we
found a couple of mistakes with refcounts, base address, missing
initialization.

A new helper was also added due to a change in the SoundWire
programming sequences, with the host driver in charge of setting up
the DMA channel mapping instead of the firmware.

The memory allocated for the tuples array assumes that there's 1
instance of all tokens already. So for those tokens that have multiple
instances in topology, we need to exclude the initial instance that has
already been accounted for.

Fixes: 4fdef47a ("ASoC: SOF: ipc4-topology: Add new tokens for input/output pin format count")
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230515085200.17094-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

Using the same token ID for both input and output format pin index
results in collisions and incorrect pin index getting parsed from
topology.

Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230515104403.32207-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:

Three patch to correct error path PM runtime handling in few places.

Regards,
Peter
---
Pierre-Louis Bossart (3):
  ASoC: SOF: debug: conditionally bump runtime_pm counter on exceptions
  ASoC: SOF: pcm: fix pm_runtime imbalance in error handling
  ASoC: SOF: sof-client-probes: fix pm_runtime imbalance in error
    handling

 sound/soc/sof/debug.c             |  4 ++--
 sound/soc/sof/pcm.c               | 11 ++++++-----
 sound/soc/sof/sof-client-probes.c | 14 ++++++++------
 3 files changed, 16 insertions(+), 13 deletions(-)

--
2.40.1

I'm leaving Cirrus Logic, and will no longer have access to
hardware and documentation necessary to be effective in a
maintainership role.

Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230512154503.741718-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org

Flush the SoundWire interrupt handler work instead of cancelling it.

When a SoundWire interrupt is triggered the pm_runtime is held
until the work has completed. It's therefore unsafe to cancel
the work, it must be flushed.

Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230512144237.739000-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org

Topology could have more instances of the tokens being searched for than
the number of sets that need to be copied. Stop copying token after the
limit of number of token instances has been reached. This worked before
only by chance as we had allocated more size for the tuples array than
the number of actual tokens being parsed.

Fixes: 7006d20e ("ASoC: SOF: Introduce IPC3 ops")
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512114630.24439-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

If there are failures in DSP runtime resume, the device state will not
reach active and this makes it impossible e.g. to retrieve a possible
DSP panic dump via "exception" debugfs node. If
CONFIG_SND_SOC_SOF_DEBUG_ENABLE_DEBUGFS_CACHE=y is set, the data in
cache is stale. If debugfs cache is not used, the region simply cannot
be read.

To allow debugging these scenarios, update the debugfs cache contents in
resume error handler. User-space can then later retrieve DSP panic and
other state via debugfs (requires SOF debugfs cache to be enabled in
build).

Reported-by: Curtis Malainey <cujomalainey@chromium.org
Link: https://github.com/thesofproject/linux/issues/4274
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512104638.21376-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

Remove Krzysztof Kozlowski from maintainer of Samsung SoC Audio drivers
and change the status to maintenance (no one is reality being paid for
looking at this).

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com
Link: https://lore.kernel.org/r/20230513090228.4340-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org

When devm runs function in the "remove" path for a device it runs them
in the reverse order. That means that if you have parts of your driver
that aren't using devm or are using "roll your own" devm w/
devm_add_action_or_reset() you need to keep that in mind.

The mt8186 audio driver didn't quite get this right. Specifically, in
mt8186_init_clock() it called mt8186_audsys_clk_register() and then
went on to call a bunch of other devm function. The caller of
mt8186_init_clock() used devm_add_action_or_reset() to call
mt8186_deinit_clock() but, because of the intervening devm functions,
the order was wrong.

Specifically at probe time, the order was:
1. mt8186_audsys_clk_register()
2. afe_priv->clk = devm_kcalloc(...)
3. afe_priv->clk[i] = devm_clk_get(...)

At remove time, the order (which should have been 3, 2, 1) was:
1. mt8186_audsys_clk_unregister()
3. Free all of afe_priv->clk[i]
2. Free afe_priv->clk

The above seemed to be causing a use-after-free. Luckily, it's easy to
fix this by simply using devm more correctly. Let's move the
devm_add_action_or_reset() to the right place. In addition to fixing
the use-after-free, code inspection shows that this fixes a leak
(missing call to mt8186_audsys_clk_unregister()) that would have
happened if any of the syscon_regmap_lookup_by_phandle() calls in
mt8186_init_clock() had failed.

Fixes: 55b423d5 ("ASoC: mediatek: mt8186: support audio clock control in platform driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/20230511092437.1.I31cceffc8c45bb1af16eb613e197b3df92cdc19e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org

The commands in sof_ipc_dai_config.flags are encoded as bits:
1 (bit0) - hw_params
2 (bit1) - hw_free
4 (bit2) - pause

These are commands, they cannot be combined as one would assume, for
example
3 (bit0 | bit1) is invalid.

This can happen right at the second start of a stream as at the end of the
first stream we set the hw_free command (bit1) and on the second start we
would OR on top of it the hw_params (bit0).

Fixes: b66bfc3a ("ASoC: SOF: sof-audio: Fix broken early bclk feature for SSP")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230512110317.5180-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

When an error occurs, we need to make sure the device can pm_runtime
suspend instead of keeping it active.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512103315.8921-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

When an error occurs, we need to make sure the device can pm_runtime
suspend instead of keeping it active.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512103315.8921-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

When a firmware IPC error happens during a pm_runtime suspend, we
ignore the error and suspend anyways. However, the code
unconditionally increases the runtime_pm counter. This results in a
confusing configuration where the code will suspend, resume but never
suspend again due to the use of pm_runtime_get_noresume().

The intent of the counter increase was to prevent entry in D3, but if
that transition to D3 is already started it cannot be stopped. In
addition, there's no point in that case in trying to prevent anything,
the firmware error is handled and the next resume will re-initialize
the firmware completely.

This patch changes the logic to prevent suspend when the device is
pm_runtime active and has a use_count > 0.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512103315.8921-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

These registers enable the HDaudio DMA hardware to split/merge data
from different PDIs, possibly on different links.

This capability exists for all types of HDaudio extended links, but
for now is only required for SoundWire. In the SSP/DMIC case, the IP
is programmed by the DSP firmware.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

We defined the values but never initialized it for SoundWire/SSP, fix
this miss.

A Fixes: tag is not provided as instance_offset was not used so far,
so nothing was really broken. This patch is only required for the
SoundWire support in the following patch.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

We mix the use of hlink->ml_addr and the 'ml_addr' parameter. It's the
same thing, let's align on using the parameter.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

The base_ptr value needs to be derived from the remap_addr pointer,
not the ml_addr. This base_ptr was used only in debug logs that were
so far not contributed upstream so the issue was not detected. It
needs to be fixed for SoundWire support on LunarLake.

Fixes: 17c9b6ec ("ASoC: SOF: Intel: hda-mlink: add structures to parse ALT links")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

Same functionality as for DMIC/SSP with different ID.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

In hindsight it was a very bad idea to use the same refcount for
Extended and 'legacy' HDaudio multi-links. The existing solution only
powers-up the first sublink, which causes SoundWire and SSP tests to
fail when more than one DAI is used concurrently. Solving this problem
requires per-sublink refcounting, as suggested in this patch.

The existing refcounting remains for 'legacy' HdAudio links, mainly to
avoid changing the obscure programming sequence in
snd_hdac_ext_bus_link_put().

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org

Apply a workaround for what appears to be a hardware quirk.

The problem seems to happen when enabling "whole chip power" (bit D7
register R6) for the very first time after the chip receives power. If
either "output" (D4) or "DAC" (D3) aren't powered on at that time,
playback becomes very distorted later on.

This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10:
https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229
I suspect this happens only when using an external MCLK signal (which
is the case for both of these boards).

Here are some experiments run on a Google Chameleon v3. These were run
in userspace using a wrapper around the i2cset utility:
ssmset() {
        i2cset -y 0 0x1a $(($1*2)) $2
}

For each of the following sequences, we apply power to the ssm2603
chip, set the configuration registers R0-R5 and R7-R8, run the selected
sequence, and check for distortions on playback.

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # chip, out, dac
  OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x87 # out, dac
  ssmset 0x06 0x07 # chip
  OK

  (disable MCLK)
  ssmset 0x09 0x01 # core
  ssmset 0x06 0x1f # chip
  ssmset 0x06 0x07 # out, dac
  (enable MCLK)
  OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x1f # chip
  ssmset 0x06 0x07 # out, dac
  NOT OK

  ssmset 0x06 0x1f # chip
  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # out, dac
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x0f # chip, out
  ssmset 0x06 0x07 # dac
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x17 # chip, dac
  ssmset 0x06 0x07 # out
  NOT OK

For each of the following sequences, we apply power to the ssm2603
chip, run the selected sequence, issue a reset with R15, configure
R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check
for distortions.

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # chip, out, dac
  OK

  (disable MCLK)
  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # chip, out, dac
  (enable MCLK after reset)
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x17 # chip, dac
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x0f # chip, out
  NOT OK

  ssmset 0x06 0x07 # chip, out, dac
  NOT OK

Signed-off-by: Paweł Anikiel <pan@semihalf.com
Link: https://lore.kernel.org/r/20230508113037.137627-8-pan@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org

A bunch of TI's codecs have binding schemas which force #sound-dai-cells
to one despite those codecs only having a single DAI. Allow for bindings
with zero DAI cells and deprecate the former non-zero value.

Signed-off-by: Martin Povišer <povik+lin@cutebit.org
Link: https://lore.kernel.org/r/20230509153412.62847-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org

When the CPU supplies bit/frame clocks, the system clock (clk_i2s)
is divided to produce the bit clock. This is a simple 1/N divider
with a fairly limited range, so for a given system clock frequency
only a few sample rates can be produced. Usually a wider range of
sample rates is supported by varying the system clock frequency.

The old calculation method was not very robust and could easily
produce the wrong clock rate, especially with non-standard rates.
For example, if the system clock is 1.99x the target bit clock
rate, the divider would be calculated as 1 instead of the more
accurate 2.

Instead, use a more accurate method that considers two adjacent
divider settings and selects the one that produces the least error
versus the requested rate. If the error is 5% or higher then the
rate setting is rejected to prevent garbled audio.

Skip divider calculation when the codec is supplying both the bit
and frame clock; in that case, the divider outputs are unused and
we don't want to constrain the sample rate.

Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com
Link: https://lore.kernel.org/r/20230509125134.208129-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org

Check substream and runtime variables before assigning.

Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com
Link: https://lore.kernel.org/r/20230508070510.6100-1-Vsujithkumar.Reddy@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org

There is error message when defer probe happens:

fsl-micfil-dai 30ca0000.micfil: Unbalanced pm_runtime_enable!

Fix the error handler with pm_runtime_enable and add
fsl_micfil_remove() for pm_runtime_disable.

Fixes: 47a70e6f ("ASoC: Add MICFIL SoC Digital Audio Interface driver.")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com
Link: https://lore.kernel.org/r/1683540996-6136-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org

On slow CPU (FPGA/QEMU emulated) printing overrun messages from
interrupt handler to uart console may leads to more overrun errors.
So use dev_err_ratelimited to limit the number of error messages.

Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru
Link: https://lore.kernel.org/r/20230505062820.21840-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org

Add pang12 quirk to enable the internal microphone.

Signed-off-by: Jeremy Soller <jeremy@system76.com
Signed-off-by: Tim Crawford <tcrawford@system76.com
Link: https://lore.kernel.org/r/20230505161458.19676-1-tcrawford@system76.com
Signed-off-by: Mark Brown <broonie@kernel.org

Merge tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tool updates from Arnaldo Carvalho de Melo:
 "Third version of perf tool updates, with the build problems with with
  using a 'vmlinux.h' generated from the main build fixed, and the bpf
  skeleton build disabled by default.

  Build:

   - Require libtraceevent to build, one can disable it using
     NO_LIBTRACEEVENT=1.

     It is required for tools like 'perf sched', 'perf kvm', 'perf
     trace', etc.

     libtraceevent is available in most distros so installing
     'libtraceevent-devel' should be a one-time event to continue
     building perf as usual.

     Using NO_LIBTRACEEVENT=1 produces tooling that is functional and
     sufficient for lots of users not interested in those libtraceevent
     dependent features.

   - Allow Python support in 'perf script' when libtraceevent isn't
     linked, as not all features requires it, for instance Intel PT does
     not use tracepoints.

   - Error if the python interpreter needed for jevents to work isn't
     available and NO_JEVENTS=1 isn't set, preventing a build without
     support for JSON vendor events, which is a rare but possible
     condition. The two check error messages:

        $(error ERROR: No python interpreter needed for jevents generation. Install python or build with NO_JEVENTS=1.)
        $(error ERROR: Python interpreter needed for jevents generation too old (older than 3.6). Install a newer python or build with NO_JEVENTS=1.)

   - Make libbpf 1.0 the minimum required when building with out of
     tree, distro provided libbpf.

   - Use libsdtc++'s and LLVM's libcxx's __cxa_demangle, a portable C++
     demangler, add 'perf test' entry for it.

   - Make binutils libraries opt in, as distros disable building with it
     due to licensing, they were used for C++ demangling, for instance.

   - Switch libpfm4 to opt-out rather than opt-in, if libpfm-devel (or
     equivalent) isn't installed, we'll just have a build warning:

       Makefile.config:1144: libpfm4 not found, disables libpfm4 support. Please install libpfm4-dev

   - Add a feature test for scandirat(), that is not implemented so far
     in musl and uclibc, disabling features that need it, such as
     scanning for tracepoints in /sys/kernel/tracing/events.

  perf BPF filters:

   - New feature where BPF can be used to filter samples, for instance:

      $ sudo ./perf record -e cycles --filter 'period > 1000' true
      $ sudo ./perf script
           perf-exec 2273949 546850.708501:       5029 cycles:  ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
           perf-exec 2273949 546850.708508:      32409 cycles:  ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
           perf-exec 2273949 546850.708526:     143369 cycles:  ffffffff82b4cdbf xas_start+0x5f ([kernel.kallsyms])
           perf-exec 2273949 546850.708600:     372650 cycles:  ffffffff8286b8f7 __pagevec_lru_add+0x117 ([kernel.kallsyms])
           perf-exec 2273949 546850.708791:     482953 cycles:  ffffffff829190de __mod_memcg_lruvec_state+0x4e ([kernel.kallsyms])
                true 2273949 546850.709036:     501985 cycles:  ffffffff828add7c tlb_gather_mmu+0x4c ([kernel.kallsyms])
                true 2273949 546850.709292:     503065 cycles:      7f2446d97c03 _dl_map_object_deps+0x973 (/usr/lib/x86_64-linux-gnu/ld-linux-x86-64.so.2)

   - In addition to 'period' (PERF_SAMPLE_PERIOD), the other
     PERF_SAMPLE_ can be used for filtering, and also some other sample
     accessible values, from tools/perf/Documentation/perf-record.txt:

        Essentially the BPF filter expression is:

        <term> <operator> <value> (("," | "||") <term> <operator> <value>)*

     The <term> can be one of:
        ip, id, tid, pid, cpu, time, addr, period, txn, weight, phys_addr,
        code_pgsz, data_pgsz, weight1, weight2, weight3, ins_lat, retire_lat,
        p_stage_cyc, mem_op, mem_lvl, mem_snoop, mem_remote, mem_lock,
        mem_dtlb, mem_blk, mem_hops

     The <operator> can be one of:
        ==, !=, >, >=, <, <=, &

     The <value> can be one of:
        <number> (for any term)
        na, load, store, pfetch, exec (for mem_op)
        l1, l2, l3, l4, cxl, io, any_cache, lfb, ram, pmem (for mem_lvl)
        na, none, hit, miss, hitm, fwd, peer (for mem_snoop)
        remote (for mem_remote)
        na, locked (for mem_locked)
        na, l1_hit, l1_miss, l2_hit, l2_miss, any_hit, any_miss, walk, fault (for mem_dtlb)
        na, by_data, by_addr (for mem_blk)
        hops0, hops1, hops2, hops3 (for mem_hops)

  perf lock contention:

   - Show lock type with address.

   - Track and show mmap_lock, siglock and per-cpu rq_lock with address.
     This is done for mmap_lock by following the current->mm pointer:

      $ sudo ./perf lock con -abl -- sleep 10
       contended   total wait     max wait     avg wait            address   symbol
       ...
           16344    312.30 ms      2.22 ms     19.11 us   ffff8cc702595640
           17686    310.08 ms      1.49 ms     17.53 us   ffff8cc7025952c0
               3     84.14 ms     45.79 ms     28.05 ms   ffff8cc78114c478   mmap_lock
            3557     76.80 ms     68.75 us     21.59 us   ffff8cc77ca3af58
               1     68.27 ms     68.27 ms     68.27 ms   ffff8cda745dfd70
               9     54.53 ms      7.96 ms      6.06 ms   ffff8cc7642a48b8   mmap_lock
           14629     44.01 ms     60.00 us      3.01 us   ffff8cc7625f9ca0
            3481     42.63 ms    140.71 us     12.24 us   ffffffff937906ac   vmap_area_lock
           16194     38.73 ms     42.15 us      2.39 us   ffff8cd397cbc560
              11     38.44 ms     10.39 ms      3.49 ms   ffff8ccd6d12fbb8   mmap_lock
               1      5.43 ms      5.43 ms      5.43 ms   ffff8cd70018f0d8
            1674      5.38 ms    422.93 us      3.21 us   ffffffff92e06080   tasklist_lock
             581      4.51 ms    130.68 us      7.75 us   ffff8cc9b1259058
               5      3.52 ms      1.27 ms    703.23 us   ffff8cc754510070
             112      3.47 ms     56.47 us     31.02 us   ffff8ccee38b3120
             381      3.31 ms     73.44 us      8.69 us   ffffffff93790690   purge_vmap_area_lock
             255      3.19 ms     36.35 us     12.49 us   ffff8d053ce30c80

   - Update default map size to 16384.

   - Allocate single letter option -M for --map-nr-entries, as it is
     proving being frequently used.

   - Fix struct rq lock access for older kernels with BPF's CO-RE
     (Compile once, run everywhere).

   - Fix problems found with MSAn.

  perf report/top:

   - Add inline information when using --call-graph=fp or lbr, as was
     already done to the --call-graph=dwarf callchain mode.

   - Improve the 'srcfile' sort key performance by really using an
     optimization introduced in 6.2 for the 'srcline' sort key that
     avoids calling addr2line for comparision with each sample.

  perf sched:

   - Make 'perf sched latency/map/replay' to use "sched:sched_waking"
     instead of "sched:sched_waking", consistent with 'perf record'
     since d566a9c2 ("perf sched: Prefer sched_waking event when it
     exists").

  perf ftrace:

   - Make system wide the default target for latency subcommand, run the
     following command then generate some network traffic and press
     control+C:

       # perf ftrace latency -T __kfree_skb
     ^C
         DURATION     |      COUNT | GRAPH                                          |
          0 - 1    us |         27 | #############                                  |
          1 - 2    us |         22 | ###########                                    |
          2 - 4    us |          8 | ####                                           |
          4 - 8    us |          5 | ##                                             |
          8 - 16   us |         24 | ############                                   |
         16 - 32   us |          2 | #                                              |
         32 - 64   us |          1 |                                                |
         64 - 128  us |          0 |                                                |
        128 - 256  us |          0 |                                                |
        256 - 512  us |          0 |                                                |
        512 - 1024 us |          0 |                                                |
          1 - 2    ms |          0 |                                                |
          2 - 4    ms |          0 |                                                |
          4 - 8    ms |          0 |                                                |
          8 - 16   ms |          0 |                                                |
         16 - 32   ms |          0 |                                                |
         32 - 64   ms |          0 |                                                |
         64 - 128  ms |          0 |                                                |
        128 - 256  ms |          0 |                                                |
        256 - 512  ms |          0 |                                                |
        512 - 1024 ms |          0 |                                                |
          1 - ...   s |          0 |                                                |
       #

  perf top:

   - Add --branch-history (LBR: Last Branch Record) option, just like
     already available for 'perf record'.

   - Fix segfault in thread__comm_len() where thread->comm was being
     used outside thread->comm_lock.

  perf annotate:

   - Allow configuring objdump and addr2line in ~/.perfconfig., so that
     you can use alternative binaries, such as llvm's.

  perf kvm:

   - Add TUI mode for 'perf kvm stat report'.

  Reference counting:

   - Add reference count checking infrastructure to check for use after
     free, done to the 'cpumap', 'namespaces', 'maps' and 'map' structs,
     more to come.

     To build with it use -DREFCNT_CHECKING=1 in the make command line
     to build tools/perf. Documented at:

       https://perf.wiki.kernel.org/index.php/Reference_Count_Checking

   - The above caught, for instance, fix, present in this series:

        - Fix maps use after put in 'perf test "Share thread maps"':

          'maps' is copied from leader, but the leader is put on line 79
          and then 'maps' is used to read the reference count below - so
          a use after put, with the put of maps happening within
          thread__put.

     Fixed by reversing the order of puts so that the leader is put
     last.

   - Also several fixes were made to places where reference counts were
     not being held.

   - Make this one of the tests in 'make -C tools/perf build-test' to
     regularly build test it and to make sure no direct access to the
     reference counted structs are made, doing that via accessors to
     check the validity of the struct pointer.

  ARM64:

   - Fix 'perf report' segfault when filtering coresight traces by
     sparse lists of CPUs.

   - Add support for 'simd' as a sort field for 'perf report', to show
     ARM's NEON SIMD's predicate flags: "partial" and "empty".

  arm64 vendor events:

   - Add N1 metrics.

  Intel vendor events:

   - Add graniterapids, grandridge and sierraforrest events.

   - Refresh events for: alderlake, aldernaken, broadwell, broadwellde,
     broadwellx, cascadelakx, haswell, haswellx, icelake, icelakex,
     jaketown, meteorlake, knightslanding, sandybridge, sapphirerapids,
     silvermont, skylake, tigerlake and westmereep-dp

   - Refresh metrics for alderlake-n, broadwell, broadwellde,
     broadwellx, haswell, haswellx, icelakex, ivybridge, ivytown and
     skylakex.

  perf stat:

   - Implement --topdown using JSON metrics.

   - Add TopdownL1 JSON metric as a default if present, but disable it
     for now for some Intel hybrid architectures, a series of patches
     addressing this is being reviewed and will be submitted for v6.5.

   - Use metrics for --smi-cost.

   - Update topdown documentation.

  Vendor events (JSON) infrastructure:

   - Add support for computing and printing metric threshold values. For
     instance, here is one found in thesapphirerapids json file:

       {
           "BriefDescription": "Percentage of cycles spent in System Management Interrupts.",
           "MetricExpr": "((msr@aperf@ - cycles) / msr@aperf@ if msr@smi@ > 0 else 0)",
           "MetricGroup": "smi",
           "MetricName": "smi_cycles",
           "MetricThreshold": "smi_cycles > 0.1",
           "ScaleUnit": "100%"
       },

   - Test parsing metric thresholds with the fake PMU in 'perf test
     pmu-events'.

   - Support for printing metric thresholds in 'perf list'.

   - Add --metric-no-threshold option to 'perf stat'.

   - Add rand (reverse and) and has_pmem (optane memory) support to
     metrics.

   - Sort list of input files to avoid depending on the order from
     readdir() helping in obtaining reproducible builds.

  S/390:

   - Add common metrics: - CPI (cycles per instruction), prbstate (ratio
     of instructions executed in problem state compared to total number
     of instructions), l1mp (Level one instruction and data cache misses
     per 100 instructions).

   - Add cache metrics for z13, z14, z15 and z16.

   - Add metric for TLB and cache.

  ARM:

   - Add raw decoding for SPE (Statistical Profiling Extension) v1.3 MTE
     (Memory Tagging Extension) and MOPS (Memory Operations) load/store.

  Intel PT hardware tracing:

   - Add event type names UINTR (User interrupt delivered) and UIRET
     (Exiting from user interrupt routine), documented in table 32-50
     "CFE Packet Type and Vector Fields Details" in the Intel Processor
     Trace chapter of The Intel SDM Volume 3 version 078.

   - Add support for new branch instructions ERETS and ERETU.

   - Fix CYC timestamps after standalone CBR

  ARM CoreSight hardware tracing:

   - Allow user to override timestamp and contextid settings.

   - Fix segfault in dso lookup.

   - Fix timeless decode mode detection.

   - Add separate decode paths for timeless and per-thread modes.

  auxtrace:

   - Fix address filter entire kernel size.

  Miscellaneous:

   - Fix use-after-free and unaligned bugs in the PLT handling routines.

   - Use zfree() to reduce chances of use after free.

   - Add missing 0x prefix for addresses printed in hexadecimal in 'perf
     probe'.

   - Suppress massive unsupported target platform errors in the unwind
     code.

   - Fix return incorrect build_id size in elf_read_build_id().

   - Fix 'perf scripts intel-pt-events.py' IPC output for Python 2 .

   - Add missing new parameter in kfree_skb tracepoint to the python
     scripts using it.

   - Add 'perf bench syscall fork' benchmark.

   - Add support for printing PERF_MEM_LVLNUM_UNC (Uncached access) in
     'perf mem'.

   - Fix wrong size expectation for perf test 'Setup struct
     perf_event_attr' caused by the patch adding
     perf_event_attr::config3.

   - Fix some spelling mistakes"

* tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (365 commits)
  Revert "perf build: Make BUILD_BPF_SKEL default, rename to NO_BPF_SKEL"
  Revert "perf build: Warn for BPF skeletons if endian mismatches"
  perf metrics: Fix SEGV with --for-each-cgroup
  perf bpf skels: Stop using vmlinux.h generated from BTF, use subset of used structs + CO-RE
  perf stat: Separate bperf from bpf_profiler
  perf test record+probe_libc_inet_pton: Fix call chain match on x86_64
  perf test record+probe_libc_inet_pton: Fix call chain match on s390
  perf tracepoint: Fix memory leak in is_valid_tracepoint()
  perf cs-etm: Add fix for coresight trace for any range of CPUs
  perf build: Fix unescaped # in perf build-test
  perf unwind: Suppress massive unsupported target platform errors
  perf script: Add new parameter in kfree_skb tracepoint to the python scripts using it
  perf script: Print raw ip instead of binary offset for callchain
  perf symbols: Fix return incorrect build_id size in elf_read_build_id()
  perf list: Modify the warning message about scandirat(3)
  perf list: Fix memory leaks in print_tracepoint_events()
  perf lock contention: Rework offset calculation with BPF CO-RE
  perf lock contention: Fix struct rq lock access
  perf stat: Disable TopdownL1 on hybrid
  perf stat: Avoid SEGV on counter->name
  ...

Pull debugobjects fix from Thomas Gleixner:
 "A single fix for debugobjects:

  The recent fix to ensure atomicity of lookup and allocation
  inadvertently broke the pool refill mechanism, so that debugobject
  OOMs now in certain situations. The reason is that the functions which
  got updated no longer invoke debug_objecs_init(), which is now the
  only place to care about refilling the tracking object pool.

  Restore the original behaviour by adding explicit refill opportunities
  to those places"

* tag 'core-debugobjects-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  debugobject: Ensure pool refill (again)

Pull crypto fixes from Herbert Xu:

 - A long-standing bug in crypto_engine

 - A buggy but harmless check in the sun8i-ss driver

 - A regression in the CRYPTO_USER interface

* tag 'v6.4-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: api - Fix CRYPTO_USER checks for report function
  crypto: engine - fix crypto_queue backlog handling
  crypto: sun8i-ss - Fix a test in sun8i_ss_setup_ivs()

Pull cifs fixes from Steve French:
 "smb3 client fixes, mostly DFS or reconnect related:

   - Two DFS connection sharing fixes

   - DFS refresh fix

   - Reconnect fix

   - Two potential use after free fixes

   - Also print prefix patch in mount debug msg

   - Two small cleanup fixes"

* tag '6.4-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Remove unneeded semicolon
  cifs: fix sharing of DFS connections
  cifs: avoid potential races when handling multiple dfs tcons
  cifs: protect access of TCP_Server_Info::{origin,leaf}_fullpath
  cifs: fix potential race when tree connecting ipc
  cifs: fix potential use-after-free bugs in TCP_Server_Info::hostname
  cifs: print smb3_fs_context::source when mounting
  cifs: protect session status check in smb2_reconnect()
  SMB3.1.1: correct definition for app_instance_id create contexts