- 05 Feb, 2013 37 commits
-
-
Sylwester Nawrocki authored
This patch adds V4L2 sub-device driver for OV9650/OV9652 image sensors. The driver exposes following V4L2 controls: - auto/manual exposure, - auto/manual white balance, - auto/manual gain, - brightness, saturation, sharpness, - horizontal/vertical flip, - color bar test pattern, - banding filter (power line frequency). Frame rate can be configured with g/s_frame_interval pad level ops. Supported resolution are only: SXGA, VGA, QVGA. Signed-off-by:
Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sylwester Nawrocki authored
This patch adds a v4l2 core helper function that can be used as the log_status handler for subdevs that only need to log state of the v4l2 controls owned by the subdev's control handler. Signed-off-by:
-
Sylwester Nawrocki authored
Add a v4l2 core helper function that can be used as the subdev .subscribe_event handler. This allows to eliminate some boilerplate from drivers that are only handling the control events. Signed-off-by:
-
Sylwester Nawrocki authored
Add a v4l2 core helper function that can be used as the subdev .unsubscribe_event handler. This allows to eliminate some boilerplate from drivers that are only handling the control events. Signed-off-by:
-
Sylwester Nawrocki authored
This patch adds a helper function that allows to modify range, i.e. minimum, maximum, step and default value of a v4l2 control, after the control has been created and initialized. This is helpful in situations when range of a control depends on user configurable parameters, e.g. camera sensor absolute exposure time depending on an output image resolution and frame rate. v4l2_ctrl_modify_range() function allows to modify range of an INTEGER, BOOL, MENU, INTEGER_MENU and BITMASK type controls. Based on a patch from Hans Verkuil http://patchwork.linuxtv.org/patch/8654. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Sylwester Nawrocki authored
Add common header file defining standard image sizes, so we can avoid redefining those in each driver. Signed-off-by:
-
Hans de Goede authored
Instead chaneg the passed in format to the pwc default pixelformat. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by:Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by:
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Also replaced: #if !defined CONFIG_USB_SN9C102 && !defined CONFIG_USB_SN9C102_MODULE with: #if !IS_ENABLED(CONFIG_USB_SN9C102) Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: -
Peter Senna Tschudin authored
replace: #if defined(CONFIG_USB_SI470X) || \ defined(CONFIG_USB_SI470X_MODULE) with: #if IS_ENABLED(CONFIG_USB_SI470X) This change was made for: CONFIG_USB_SI470X, CONFIG_I2C_SI470X Reported-by: -
Johannes Schellen authored
This patch fixes a bug which causes all histogram regions to start in the top left corner of the image. The histogram region coordinates are 16 bit values which share a 32 bit register. The bug is due to the region end value assignments overwriting the region start values with zero. Signed-off-by:
Johannes Schellen <Johannes.Schellen@rwth-aachen.de> Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
Replace kzalloc, request_mem_region, ioremap, clk_get and regulator_get with their devm_* managed replacement. Signed-off-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
-
Laurent Pinchart authored
kzalloc initializes the memory it allocates to 0, there's no need for an explicit memset. Signed-off-by:
-
Laurent Pinchart authored
The preview engine includes filters that consume columns and lines as part of their operation, thus resulting in a cropped image. To allow turning those filters on/off during streaming without affecting the output image size, the driver adds additional cropping to make the total number of cropped columns and lines constant regardless of which filters are enabled. This process needlessly includes the CFA filter, as whether the filter is enabled only depends on the sink pad format, which can't change during streaming. Exclude the CFA filter from the preview engine margins. Signed-off-by:
-
Oliver Neukum authored
Ming Lei reported: IMO, there is a minor fault in the error handling path of uvc_status_start() inside uvc_v4l2_open(), and the 'users' count should have been decreased before usb_autopm_put_interface(). In theory, a [URB resubmission] warning can be triggered when the device is opened just between usb_autopm_put_interface() and atomic_dec(&stream->dev->users). The fix is trivial. Reported-by:
Ming Lei <tom.leiming@gmail.com> Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Ezequiel Garcia authored
This kind of memcpy() is error-prone. Its replacement with a struct assignment is prefered because it's type-safe and much easier to read. Signed-off-by:
Ezequiel Garcia <elezegarcia@gmail.com> Signed-off-by:
-
Wei Yongjun authored
Add the missing unlock on the error handling path in function vpbe_initialize(). Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by:
Prabhakar Lad <prabhakar.lad@ti.com> Signed-off-by:
-
Lad, Prabhakar authored
drivers/media/platform/davinci/dm355_ccdc.c:593:9: warning: ‘val1’ may be used uninitialized in this function [-Wuninitialized] drivers/media/platform/davinci/dm355_ccdc.c:560:6: note: ‘val1’ was declared here This is a false positive but the compiler has no way to know about it, so initialize the variable to 0. Signed-off-by:
-
Lad, Prabhakar authored
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so simplifies their clean up paths. Signed-off-by:
Manjunath Hadli <manjunath.hadli@ti.com> Acked-by:
-
Lad, Prabhakar authored
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so simplifies their clean up paths. Signed-off-by:
-
Lad, Prabhakar authored
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so simplifies their clean up paths. Signed-off-by:
-
Lad, Prabhakar authored
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so simplifies their clean up paths. Signed-off-by:
-
Paul Bolle authored
Compiling the saa7164 driver without CONFIG_VIDEO_ADV_DEBUG set triggers these GCC warnings: drivers/media/pci/saa7164/saa7164-encoder.c:1301:12: warning: ‘saa7164_g_register’ defined but not used [-Wunused-function] drivers/media/pci/saa7164/saa7164-encoder.c:1314:12: warning: ‘saa7164_s_register’ defined but not used [-Wunused-function] Silence these warnings by wrapping these two functions in an "#ifdef CONFIG_VIDEO_ADV_DEBUG" and "#endif" pair. Signed-off-by:Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
- 01 Feb, 2013 1 commit
-
-
Alexandre Lissy authored
Events for the iMon Knob pad where not correctly interpreted on ARM, resulting in buggy mouse movements (cursor going straight out of the screen), key pad only generating KEY_RIGHT and KEY_DOWN events. A reproducer is: int main(int argc, char ** argv) { char rel_x = 0x00; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__); rel_x = 0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__); rel_x |= ~0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__); return 0; } (running on x86 or amd64) $ ./test rel_x:0 @test.c:6 rel_x:15 @test.c:7 rel_x:-1 @test.c:8 (running on armv6) rel_x:0 @test.c:6 rel_x:15 @test.c:7 rel_x:255 @test.c:8 Forcing the rel_x and rel_y variables as signed char fixes the issue. Reference: http://www.arm.linux.org.uk/docs/faqs/signedchar.phpSigned-off-by:Alexandre Lissy <alexandrelissy@free.fr> Signed-off-by:
-
- 24 Jan, 2013 2 commits
-
-
Mauro Carvalho Chehab authored
* v4l_for_linus: (464 commits) [media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures [media] uvcvideo: Cleanup leftovers of partial revert [media] uvcvideo: Return -EACCES when trying to set a read-only control Linux 3.8-rc3 mm: reinstante dropped pmd_trans_splitting() check cred: Remove tgcred pointer from struct cred drm/ttm: fix fence locking in ttm_buffer_object_transfer ARM: clps711x: Fix bad merge of clockevents setup ARM: highbank: save and restore L2 cache and GIC on suspend ARM: highbank: add a power request clear ARM: highbank: fix secondary boot and hotplug ARM: highbank: fix typos with hignbank in power request functions ARM: dts: fix highbank cpu mpidr values ARM: dts: add device_type prop to cpu nodes on Calxeda platforms drm/prime: drop reference on imported dma-buf come from gem xen/netfront: improve truesize tracking ARM: mx5: Fix MX53 flexcan2 clock ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array sctp: fix Kconfig bug in default cookie hmac selection EDAC: Cleanup device deregistering path ... Conflicts: drivers/media/pci/dm1105/dm1105.c drivers/media/platform/soc_camera/mx2_camera.c
-
Andreas Regel authored
Sometimes there is a problem when trying to access the non-existing registers of the second demodulator path on the STV0903. This change removes the calls in case the driver is used on a STV0903. Signed-off-by:
Andreas Regel <andreas.regel@gmx.de> Acked-by:
Manu Abraham <manu@linuxtv.org> Signed-off-by:
-
