- 17 Sep, 2015 5 commits
-
-
Roger Quadros authored
The VBUS line of USB2 is connected to VBUS detect logic on the PMIC. Use the palmas-usb driver to report VBUS events to the USB driver. As the palmas-usb driver supports GPIO based ID reporting provide the GPIO for ID pin as well. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Grazvydas Ignotas authored
This enables tca6424a GPIO expander driver that in turn enables TPD12S015 HDMI ESD protection and level shifter on OMAP5 uevm. In other words, it makes HDMI work on OMAP5 uevm. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Grazvydas Ignotas authored
The i2c5 pinctrl offsets are wrong. If the bootloader doesn't set the pins up, communication with tca6424a doesn't work (controller timeouts) and it is not possible to enable HDMI. Fixes: 9be495c4 ("ARM: dts: omap5-evm: Add I2c pinctrl data") Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Dave Gerlach authored
Add omap2_clk_enable_autoidle_all to am43xx_init_late otherwise the call to omap2_clk_disable_autoidle_all in am43xx_init_early may cause some clocks to always stay active and prevent low power mode transitions. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Nishanth Menon authored
Originally, all the SoC PHY rails were supplied by LDO3. However, as a result of characterization, it was determined that this posed a risk in extreme load conditions. Hence the PHY rails are split between two different LDOs. Update the related node as a result LDO3/VDDA_1V8_PHYA supplies vdda_usb1, vdda_usb2, vdda_sata, vdda_usb3 LDO4/VDDA_1V8_PHYB supplies vdda_pcie1, vdda_pcie0, vdda_hdmi, vdda_pcie NOTE: We break compatibility with pre-production boards with this change since, the PMIC LDO4 is disabled at OTP level. The new configuration is the plan of record and all pre-production boards are supposed to be replaced with the latest boards matching the mentioned configuration. Some very few 10 something boards have been created and stopped production till the latest modifications were done (PMIC USB interrupt, LDO4 etc) - and all of those boards are now getting scrapped.. If there are any (as per tracking information, there should not be any), TI should be contacted to have them replaced. Signed-off-by: Nishanth Menon <nm@ti.com> [tony@atomide.com: updated commit about these being TI internal protos] Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 14 Sep, 2015 15 commits
-
-
Tony Lindgren authored
-
Nicolas Chauvet authored
This fix the model name for the device. Whole string taken from the HP support center web page Signed-off-by: Nicolas Chauvet <kwizart@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Vishal Mahaveer authored
Register address in name of the node is wrong Signed-off-by: Vishal Mahaveer <vishalm@ti.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
One of the lines from PCF857x is connected to the vdd line of MMC1 in DRA74x and DRA72x EVMs and is modelled as a regulator. If PCF857x is not made as built-in, the regulator_get in omap_hsmmc fails making it difficult to use MMC1 as rootfs. Make PCF857x built-in. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Use platform specific compatible strings instead of the common "ti,pbias-omap" compatible string. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Nishanth Menon authored
OMAP5 SoC has Cortex-A15 which does not use TWD timer. It uses ARCH_TIMER instead, clean up unwanted configuration and enable OMAP_INTERCONNECT and OPP which is necessary for expected functionality on the SoC. Reported-by: Carlos Hernandez <ceh@ti.com> Reported-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Nishanth Menon authored
DRA7 does use OPP, uses OMAP interconnect and also does require SCU. These are missing in the SoC only build of DRA7 breaking various PM features in DRA7 only build. Reported-by: Carlos Hernandez <ceh@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Nishanth Menon authored
When commit c4082d49 ("ARM: omap2+: board-generic: clean up the irq data from board file") cleaned up the direct usage of gic_of_init and omap_intc_of_init, it failed to clean up the macros properly. Since these macros are no longer used, lets just remove them. Fixes: c4082d49 ("ARM: omap2+: board-generic: clean up the irq data from board file") Reported-by: Carlos Hernandez <ceh@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Nishanth Menon authored
OMAP5 and DRA7 reuse the same pm44xx_erratum variable so, enable the same, else PM features such as Suspend to ram is broken in a SoC only build configuration. Reported-by: Carlos Hernandez <ceh@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Only the IGEPv2 boards have a LAN9221i chip connected to the GPMC so the pinmux configuration for the GPIO connected to the IRQ line of the LAN chip should not be defined in the IGEP common dtsi but in the one common to the IGEPv2 boards. While there, use the OMAP3_CORE1_IOPAD() macro for the padconf reg. Suggested-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Nishanth Menon authored
With the support in the generic PM framework for wakeirq and capability added to the rtc-ds1307 driver to support this, we can now define the optional wakeup irq to allow the RTC to wakeup the system from low power modes as part of suspend. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Teresa Remmet authored
Fix the mpu voltage as it is set too low for the silicon revision 2.1. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
For beagle x15, both the vdd and io lines are connected to the same regulator (ldo1_reg). However vmmc_aux is populated to vdd_3v3. Remove it. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Nishanth Menon <nm@ti.com> [tony@atomide.com: updated to apply] Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Looks like I made a typo on the control base, all the 81xx SoCs have it at 0x48140000 base. We've just gotten away with the typo as the Ethernet phy was configured by the bootloader on my test system and we're not yet using the pinctrl. In addition to fixing the contol base, we need to also use the right Ethernet phy flags to initialize it. And we are still missing the PLL driver for dm814x and only relying on the divider and mux clocks. Fixes: f3d953ea ("ARM: dts: Add minimal dm814x support") Cc: Matthijs van Duin <matthijsvanduin@gmail.com> Cc: Nicolas Chauvet <kwizart@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Carl Frederik Werner authored
Let's fix pinmux address of gpio 170 used by tfp410 powerdown-gpio. According to the OMAP35x Technical Reference Manual CONTROL_PADCONF_I2C3_SDA[15:0] 0x480021C4 mode0: i2c3_sda CONTROL_PADCONF_I2C3_SDA[31:16] 0x480021C4 mode4: gpio_170 the pinmux address of gpio 170 must be 0x480021C6. The former wrong address broke i2c3 (used by hdmi ddc), resulting in kernel message: omap_i2c 48060000.i2c: controller timed out Fixes: 8cecf52b ("ARM: omap3-beagle.dts: add display information") Cc: stable@vger.kernel.org # v3.15+ Signed-off-by: Carl Frederik Werner <frederik@cfbw.eu> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 12 Sep, 2015 13 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/jesper/crisLinus Torvalds authored
Pull CRIS updates from Jesper Nilsson: "Mostly removal of old cruft of which we can use a generic version, or fixes for code not commonly run in the cris port, but also additions to enable some good debug" * tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris: (25 commits) CRISv10: delete unused lib/dmacopy.c CRISv10: delete unused lib/old_checksum.c CRIS: fix switch_mm() lockdep splat CRISv32: enable LOCKDEP_SUPPORT CRIS: add STACKTRACE_SUPPORT CRISv32: annotate irq enable in idle loop CRISv32: add support for irqflags tracing CRIS: UAPI: use generic types.h CRIS: UAPI: use generic shmbuf.h CRIS: UAPI: use generic msgbuf.h CRIS: UAPI: use generic socket.h CRIS: UAPI: use generic sembuf.h CRIS: UAPI: use generic sockios.h CRIS: UAPI: use generic auxvec.h CRIS: UAPI: use generic headers via Kbuild CRIS: UAPI: fix elf.h export CRIS: don't make asm/elf.h depend on asm/user.h CRIS: UAPI: fix ptrace.h CRISv32: Squash compile warnings for axisflashmap CRISv32: Add GPIO driver to the default configs ...
-
Linus Torvalds authored
rq_data_dir() returns either READ or WRITE (0 == READ, 1 == WRITE), not a boolean value. Now, admittedly the "!= 0" doesn't really change the value (0 stays as zero, 1 stays as one), but it's not only redundant, it confuses gcc, and causes gcc to warn about the construct switch (rq_data_dir(req)) { case READ: ... case WRITE: ... that we have in a few drivers. Now, the gcc warning is silly and stupid (it seems to warn not about the switch value having a different type from the case statements, but about _any_ boolean switch value), but in this case the code itself is silly and stupid too, so let's just change it, and get rid of warnings like this: drivers/block/hd.c: In function ‘hd_request’: drivers/block/hd.c:630:11: warning: switch condition has boolean value [-Wswitch-bool] switch (rq_data_dir(req)) { The odd '!= 0' came in when "cmd_flags" got turned into a "u64" in commit 5953316d ("block: make rq->cmd_flags be 64-bit") and is presumably because the old code (that just did a logical 'and' with 1) would then end up making the type of rq_data_dir() be u64 too. But if we want to retain the old regular integer type, let's just cast the result to 'int' rather than use that rather odd '!= 0'. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
Fix up the writeback plugging introduced in commit d353d758 ("writeback: plug writeback at a high level") that then caused problems due to the unplug happening with a spinlock held. * writeback-plugging: writeback: plug writeback in wb_writeback() and writeback_inodes_wb() Revert "writeback: plug writeback at a high level"
-
Linus Torvalds authored
We had to revert the pluggin in writeback_sb_inodes() because the wb->list_lock is held, but we could easily plug at a higher level before taking that lock, and unplug after releasing it. This does that. Chris will run performance numbers, just to verify that this approach is comparable to the alternative (we could just drop and re-take the lock around the blk_finish_plug() rather than these two commits. I'd have preferred waiting for actual performance numbers before picking one approach over the other, but I don't want to release rc1 with the known "sleeping function called from invalid context" issue, so I'll pick this cleanup version for now. But if the numbers show that we really want to plug just at the writeback_sb_inodes() level, and we should just play ugly games with the spinlock, we'll switch to that. Cc: Chris Mason <clm@fb.com> Cc: Josef Bacik <jbacik@fb.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Neil Brown <neilb@suse.de> Cc: Jan Kara <jack@suse.cz> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
I didn't notice this when merging the thermal code from Zhang, but his merge (commit 5a924a07: "Merge branches 'thermal-core' and 'thermal-intel' of .git into next") of the thermal-core and thermal-intel branches was wrong. In thermal-core, commit 17e8351a ("thermal: consistently use int for temperatures") converted the thermal layer to use "int" for temperatures. But in parallel, in the thermal-intel branch commit d0a12625 ("thermal: Add Intel PCH thermal driver") added support for the intel PCH thermal sensor using the old interfaces that used "unsigned long" pointers. This resulted in warnings like this: drivers/thermal/intel_pch_thermal.c:184:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types] .get_temp = pch_thermal_get_temp, ^ drivers/thermal/intel_pch_thermal.c:184:14: note: (near initialization for ‘tzd_ops.get_temp’) drivers/thermal/intel_pch_thermal.c:186:19: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types] .get_trip_temp = pch_get_trip_temp, ^ drivers/thermal/intel_pch_thermal.c:186:19: note: (near initialization for ‘tzd_ops.get_trip_temp’) This fixes it. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
Merge fourth patch-bomb from Andrew Morton: - sys_membarier syscall - seq_file interface changes - a few misc fixups * emailed patches from Andrew Morton <akpm@linux-foundation.org>: revert "ocfs2/dlm: use list_for_each_entry instead of list_for_each" mm/early_ioremap: add explicit #include of asm/early_ioremap.h fs/seq_file: convert int seq_vprint/seq_printf/etc... returns to void selftests: enhance membarrier syscall test selftests: add membarrier syscall test sys_membarrier(): system-wide memory barrier (generic, x86) MODSIGN: fix a compilation warning in extract-cert
-
Vineet Gupta authored
Newer bitfiles needs the reduced clk even for SMP builds Cc: <stable@vger.kernel.org> #4.2 Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://github.com/jonmason/ntbLinus Torvalds authored
Pull NTB fixes from Jon Mason: "NTB bug and documentation fixes, new device IDs, performance improvements, and adding a mailing list to MAINTAINERS for NTB" * tag 'ntb-4.3' of git://github.com/jonmason/ntb: NTB: Fix range check on memory window index NTB: Improve index handling in B2B MW workaround NTB: Fix documentation for ntb_peer_db_clear. NTB: Fix documentation for ntb_link_is_up NTB: Use unique DMA channels for TX and RX NTB: Remove dma_sync_wait from ntb_async_rx NTB: Clean up QP stats info NTB: Make the transport list in order of discovery NTB: Add PCI Device IDs for Broadwell Xeon NTB: Add flow control to the ntb_netdev NTB: Add list to MAINTAINERS
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull more input updates from Dmitry Torokhov: "Second round of updates for the input subsystem. This introduces two brand new touchscreen drivers (Colibri and imx6ul_tsc), some small driver fixes, and we are no longer report errors from evdev_flush() as users do not really have a way of handling errors, error codes that we were returning were not on the list of errors supposed to be returned by close(), and errors were causing issues with one of older versions of systemd" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: imx_keypad - remove obsolete comment Input: touchscreen - add imx6ul_tsc driver support Input: Add touchscreen support for Colibri VF50 Input: i8042 - lower log level for "no controller" message Input: evdev - do not report errors form flush() Input: elants_i2c - extend the calibration timeout to 12 seconds Input: sparcspkr - fix module autoload for OF platform drivers Input: regulator-haptic - fix module autoload for OF platform driver Input: pwm-beeper - fix module autoload for OF platform driver Input: ab8500-ponkey - Fix module autoload for OF platform driver Input: cyttsp - remove unnecessary MODULE_ALIAS() Input: elan_i2c - add ACPI ID "ELAN1000"
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull more power management and ACPI updates from Rafael Wysocki: "These are mostly fixes and cleanups on top of the previous PM+ACPI pull request (cpufreq core and drivers, cpuidle, generic power domains framework). Some of them didn't make to that pull request and some fix issues introduced by it. The only really new thing is the support for suspend frequency in the cpufreq-dt driver, but it is needed to fix an issue with Exynos platforms. Specifics: - build fix for the new Mediatek MT8173 cpufreq driver (Guenter Roeck). - generic power domains framework fixes (power on error code path, subdomain removal) and cleanup of a deprecated API user (Geert Uytterhoeven, Jon Hunter, Ulf Hansson). - cpufreq-dt driver fixes including two fixes for bugs related to the new Operating Performance Points Device Tree bindings introduced recently (Viresh Kumar). - suspend frequency support for the cpufreq-dt driver (Bartlomiej Zolnierkiewicz, Viresh Kumar). - cpufreq core cleanups (Viresh Kumar). - intel_pstate driver fixes (Chen Yu, Kristen Carlson Accardi). - additional sanity check in the cpuidle core (Xunlei Pang). - fix for a comment related to CPU power management (Lina Iyer)" * tag 'pm+acpi-4.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: intel_pstate: fix PCT_TO_HWP macro intel_pstate: Fix user input of min/max to legal policy region PM / OPP: Return suspend_opp only if it is enabled cpufreq-dt: add suspend frequency support cpufreq: allow cpufreq_generic_suspend() to work without suspend frequency PM / OPP: add dev_pm_opp_get_suspend_opp() helper staging: board: Migrate away from __pm_genpd_name_add_device() cpufreq: Use __func__ to print function's name cpufreq: staticize cpufreq_cpu_get_raw() PM / Domains: Ensure subdomain is not in use before removing cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL cpuidle/coupled: Add sanity check for safe_state_index PM / Domains: Try power off masters in error path of __pm_genpd_poweron() cpufreq: dt: Tolerance applies on both sides of target voltage cpufreq: dt: Print error on failing to mark OPPs as shared cpufreq: dt: Check OPP count before marking them shared kernel/cpu_pm: fix cpu_cluster_pm_exit comment
-
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pendingLinus Torvalds authored
Pull SCSI target updates from Nicholas Bellinger: "Here are the outstanding target-pending updates for v4.3-rc1. Mostly bug-fixes and minor changes this round. The fallout from the big v4.2-rc1 RCU conversion have (thus far) been minimal. The highlights this round include: - Move sense handling routines into scsi_common code (Sagi) - Return ABORTED_COMMAND sense key for PI errors (Sagi) - Add tpg_enabled_sendtargets attribute for disabled iscsi-target discovery (David) - Shrink target struct se_cmd by rearranging fields (Roland) - Drop iSCSI use of mutex around max_cmd_sn increment (Roland) - Replace iSCSI __kernel_sockaddr_storage with sockaddr_storage (Andy + Chris) - Honor fabric max_data_sg_nents I/O transfer limit (Arun + Himanshu + nab) - Fix EXTENDED_COPY >= v4.1 regression OOPsen (Alex + nab)" * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (37 commits) target: use stringify.h instead of own definition target/user: Fix UFLAG_UNKNOWN_OP handling target: Remove no-op conditional target/user: Remove unused variable target: Fix max_cmd_sn increment w/o cmdsn mutex regressions target: Attach EXTENDED_COPY local I/O descriptors to xcopy_pt_sess target/qla2xxx: Honor max_data_sg_nents I/O transfer limit target/iscsi: Replace __kernel_sockaddr_storage with sockaddr_storage target/iscsi: Replace conn->login_ip with login_sockaddr target/iscsi: Keep local_ip as the actual sockaddr target/iscsi: Fix np_ip bracket issue by removing np_ip target: Drop iSCSI use of mutex around max_cmd_sn increment qla2xxx: Update tcm_qla2xxx module description to 24xx+ iscsi-target: Add tpg_enabled_sendtargets for disabled discovery drivers: target: Drop unlikely before IS_ERR(_OR_NULL) target: check DPO/FUA usage for COMPARE AND WRITE target: Shrink struct se_cmd by rearranging fields target: Remove cmd->se_ordered_id (unused except debug log lines) target: add support for START_STOP_UNIT SCSI opcode target: improve unsupported opcode message ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull second round of SCSI updates from James Bottomley: "There's one late arriving patch here (added today), fixing a build issue which the scsi_dh patch set in here uncovered. Other than that, everything has been incubated in -next and the checkers for a week. The major pieces of this patch are a set patches facilitating better integration between scsi and scsi_dh (the device handling layer used by multi-path; all the dm parts are acked by Mike Snitzer). This also includes driver updates for mp3sas, scsi_debug and an assortment of bug fixes" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (50 commits) scsi_dh: fix randconfig build error scsi: fix scsi_error_handler vs. scsi_host_dev_release race fcoe: Convert use of __constant_htons to htons mpt2sas: setpci reset kernel oops fix pm80xx: Don't override ts->stat on IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY lpfc: Fix possible use-after-free and double free in lpfc_mbx_cmpl_rdp_page_a2() bfa: Fix incorrect de-reference of pointer bfa: Fix indentation scsi_transport_sas: Remove check for SAS expander when querying bay/enclosure IDs. scsi_debug: resp_request: remove unused variable scsi_debug: fix REPORT LUNS Well Known LU scsi_debug: schedule_resp fix input variable check scsi_debug: make dump_sector static scsi_debug: vfree is null safe so drop the check scsi_debug: use SCSI_W_LUN_REPORT_LUNS instead of SAM2_WLUN_REPORT_LUNS; scsi_debug: define pr_fmt() for consistent logging mpt2sas: Refcount fw_events and fix unsafe list usage mpt2sas: Refcount sas_device objects and fix unsafe list usage scsi_dh: return SCSI_DH_NOTCONN in scsi_dh_activate() scsi_dh: don't allow to detach device handlers at runtime ...
-
- 11 Sep, 2015 7 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-mediaLinus Torvalds authored
Pull media updates from Mauro Carvalho Chehab: "A series of patches that move part of the code used to allocate memory from the media subsystem to the mm subsystem" [ The mm parts have been acked by VM people, and the series was apparently in -mm for a while - Linus ] * tag 'media/v4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: [media] drm/exynos: Convert g2d_userptr_get_dma_addr() to use get_vaddr_frames() [media] media: vb2: Remove unused functions [media] media: vb2: Convert vb2_dc_get_userptr() to use frame vector [media] media: vb2: Convert vb2_vmalloc_get_userptr() to use frame vector [media] media: vb2: Convert vb2_dma_sg_get_userptr() to use frame vector [media] vb2: Provide helpers for mapping virtual addresses [media] media: omap_vout: Convert omap_vout_uservirt_to_phys() to use get_vaddr_pfns() [media] mm: Provide new get_vaddr_frames() helper [media] vb2: Push mmap_sem down to memops
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edacLinus Torvalds authored
Pull edac updates from Mauro Carvalho Chehab: "Two EDAC fixes for Intel systems (Haswell and Ivy Bridge)" * tag 'edac/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: sb_edac: correctly fetch DIMM width on Ivy Bridge and Haswell sb_edac: look harder for DDRIO on Haswell systems
-
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linuxLinus Torvalds authored
Pull thermal updates from Zhang Rui: - use int instead of unsigned long to represent temperature to avoid bogus overheat detection when negative temperature reported. From Sascha Hauer. - export available thermal governors information to user space via sysfs. From Wei Ni. - introduce new thermal driver for Wildcat Point platform controller hub, which uses PCH thermal sensor and associated critical and hot trip points. From Tushar Dave. - add suuport for Intel Skylake and Denlow platforms in powerclamp driver. - some small cleanups in thermal core. * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: thermal: Add Intel PCH thermal driver thermal: Add comment explaining test for critical temperature thermal: Use IS_ENABLED instead of #ifdef thermal: remove unnecessary call to thermal_zone_device_set_polling thermal: trivial: fix typo in comment thermal: consistently use int for temperatures thermal: add available policies sysfs attribute thermal/powerclamp: add cpu id for denlow platform thermal/powerclamp: add cpu id for Skylake u/y thermal/powerclamp: add cpu id for skylake h/s
-
Andrew Morton authored
Revert commit f83c7b5e ("ocfs2/dlm: use list_for_each_entry instead of list_for_each"). list_for_each_entry() will dereference its `pos' argument, which can be NULL in dlm_process_recovery_data(). Reported-by: Julia Lawall <julia.lawall@lip6.fr> Reported-by: Fengguang Wu <fengguang.wu@gmail.com> Cc: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Ard Biesheuvel authored
Commit 6b0f68e3 ("mm: add utility for early copy from unmapped ram") introduces a function copy_from_early_mem() into mm/early_ioremap.c which itself calls early_memremap()/early_memunmap(). However, since early_memunmap() has not been declared yet at this point in the .c file, nor by any explicitly included header files, we are depending on a transitive include of asm/early_ioremap.h to declare it, which is fragile. So instead, include this header explicitly. Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by: Mark Salter <msalter@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Joe Perches authored
The seq_<foo> function return values were frequently misused. See: commit 1f33c41c ("seq_file: Rename seq_overflow() to seq_has_overflowed() and make public") All uses of these return values have been removed, so convert the return types to void. Miscellanea: o Move seq_put_decimal_<type> and seq_escape prototypes closer the other seq_vprintf prototypes o Reorder seq_putc and seq_puts to return early on overflow o Add argument names to seq_vprintf and seq_printf o Update the seq_escape kernel-doc o Convert a couple of leading spaces to tabs in seq_escape Signed-off-by: Joe Perches <joe@perches.com> Cc: Al Viro <viro@ZenIV.linux.org.uk> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Mark Brown <broonie@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Joerg Roedel <jroedel@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Mathieu Desnoyers authored
Update the membarrier syscall self-test to match the membarrier interface. Extend coverage of the interface. Consider ENOSYS as a "SKIP" test, since it is a valid configuration, but does not allow testing the system call. Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Pranith Kumar <bobby.prani@gmail.com> Cc: Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-