The GW74xx supports an on-board Laird Connectivity Sterling LWB5+ module
which uses a Cypress CYW4373W chip to provide 1x1 802.11 a/b/g/n/ac +
Bluetooth 5.2.

Add the proper device-tree nodes for it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add regulator config for cpu-supply in order to support cpufreq.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for USB DR on USB1 interface. Host/Device detection is done
using the usb-role-switch connector with a GPIO as USB1_OTG_ID is not
connected internally.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX93 mediamix blk ctrl node
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX93 SRC node
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Commit "arm64: dts: ls1028a: enable swp5 and eno3 for all boards" which
Shawn declared as applied, but for which I can't find a sha1sum, has
enabled a new Ethernet port on the LS1028A-RDB (&enetc_port3), but
U-Boot, which passes a MAC address to Linux' device tree through the
/aliases node, fails to do this for this newly enabled port.

Fix that by adding more ethernet aliases in the only
backwards-compatible way possible: at the end of the current list.

And since it is possible to very easily convert either swp4 or swp5 to
DSA user ports now (which have a MAC address of their own), using these
U-Boot commands:

=> fdt addr $fdt_addr_r
=> fdt rm /soc/pcie@1f0000000/ethernet-switch@0,5/ports/port@4 ethernet

it would be good if those DSA user ports (swp4, swp5) gained a valid MAC
address from U-Boot as well. In order for that to work properly,
provision two more ethernet aliases for &mscc_felix_port{4,5} as well.

The resulting ordering is slightly unusual, but to me looks more natural
than eno0, eno2, swp0, swp1, swp2, swp3, eno3, swp4, swp5.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Node names should be generic, so change the sdma node name format 'sdma'
into 'dma-controller'.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX93 lpspi nodes
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX93 lpi2c nodes
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add A55 PMU node for perf usage
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX93 BLK CTRL MIX node
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add s4 mu node for sentinel communication
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the GPIO clk, otherwise GPIO may not work if clk driver disable the
GPIO clk during kernel boot.
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

DUMMY clk only works with clk_ignore_unused and bootloader enables those
clks that required for SDHC work properly.

Correct SDHC clk entry with real clk.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for USB DR on USB1 interface. Host/Device detection is done
using the usb-role-switch connector.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Lontium LT8912B driver needs a HDMI connector to be connected to
port 1. Introduce this connector to be enabled in a device tree overlay.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add an LVDS panel node to be extended by a device tree overlay.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Rename sn65dsi83 to sn65dsi84 as that is the exact chip used on the
Verdin DSI to LVDS Adapter.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

LPSPI transfer max speed is half of the root clock.
Increase the root clock speed to support faster data transmission.

And update the parent clock of all i2c/spi with IMX8ULP_CLK_FROSC_DIV2
which could produce accurate clock for i2c/spi usage.
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Sentinel Message Unit(MU), Generic MU nodes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX8ULP pmu node
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Follow sram/sram.yaml to update the sram node name.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The clocks and clocks-names are not documented in binding doc,
and the clk-imx8ulp driver not use the undocumented property,
so drop them.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Properties are not documented so lead to the following error:
'#address-cells', '#size-cells', 'interrupts' do not match any of the regexes: 'pinctrl-[0-9]+'

Fix this by removing unneeded properties.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In order to enable (PD and data) role switching on the Librem 5 phone,
add the usb-role-switch property to imx8mq's dwc3 node.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the connector properties to the USB type-c stanza to enable (PD)
role-switching on the Librem 5 phone.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This allows the userspace to notice that there's not enough
current provided to charge the battery, and also fixes issues
with 0% SOC values being considered invalid.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Describe the RGB notification leds on the Librem 5 phone.
Use the common defines so we're sure to adhere to the common patterns,
use predefined led colors and functions so we're being warned in case
of deprecations.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Describe the focus motor that will be used for the rear camera - even
though the rear camera sensor driver is not yet in the mainline. The
focus motor is a separate device and can be controlled already.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In order for the LS1028A based boards to benefit from support for
multiple CPU ports, the second DSA master and its associated CPU port
must be enabled in the device trees. This does not change the default
CPU port from the current port 4.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The LS1028A switch has 2 internal links to the ENETC controller.

With DSA's ability to support multiple CPU ports, we should mark both
ENETC ports as DSA masters.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since the CPU port 4 of the switch is hardwired inside the SoC to go to
the enetc port 2, this shouldn't be something that the board files need
to set (but whether that CPU port is used or not is another discussion).

So move the DSA "ethernet" property to the common dtsi.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add PCIe support on i.MX8MP EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX8MP PCIe support.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This fixes the following error:

arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h: error: do not set
 execute permissions for source files
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add SNVS LPGPR bindings to MX8M Plus, the LPGPR is used to store
e.g. boot counter.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device trees for one of a number of MSC's (parent company, Avnet)
variants of the SM2S-IMX8PLUS system on module along with the compatible
SM2S-SK-AL-EP1 carrier board. As the name suggests, this family of SoMs use
the NXP i.MX8MP SoC and provide the SMARC module interface.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix the Amarula Solutions typo mistake in license text for Engicam
i.MX8M boards add in below commits.

commit <60ac3526> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M
Mini SoM")
commit <aec8ad34> ("arm64: dts: imx8mp: Add Engicam i.Core MX8M
Plus EDIMM2.2 Starter Kit")
commit <eefe06b2> ("arm64: dts: imx8mp: Add Engicam i.Core MX8M
Plus SoM")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8 LPI2C requires both PER and IPG clock, so add the missed IPG clk.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for the Kontron Electronics SL i.MX8MM OSM-S SoM
and the matching baseboard BL i.MX8MM OSM-S.

The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>