Add code to query and set the number of channels on the primary VSI for a
PF. This is accessed from the 'ethtool -l' and 'ethtool -L' commands,
respectively.  Though the ice driver supports asymmetric queues report an
IRQ vector that has both Rx and Tx queues attached and is counted as a
'combined' channel.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement the VF stats gathering via the kernel via ndo_get_vf_stats().
The driver will show per-VF stats in the output of the
ip -s link show dev <PF> command.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The virtchannel interface was repeating a lot of strings
and wasting storage space in the kernel.  There was also
inconsistent messages for the same thing.  Consolidate all
those messages and bit checks into a couple of helper functions.

Also, reduce stack space usage by simplifying getting the pointer
to the pf using a helper.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We use &pf->dev->pdev all over the code. Add a simple
macro to do this for us. When multiple de-references
like this are being done add a local struct device
variable.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In situations where we alloc and free memory within the same function do
not use the devm_* variants; use regular alloc and free functions. Remove
any unused vars if there are no usages after these changes.

Also, replace an allocate and copy with kmemdup() and remove an
unnecessary memset() to 0 after a kzalloc().
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently ice_clear_vsi_promisc() detects if the VLAN ID sent is not 0
and sets the recipe_id to ICE_SW_LKUP_PROMISC_VLAN in that case and
ICE_SW_LKUP_PROMISC if the VLAN_ID is 0. However this doesn't allow VLAN
0 promiscuous rules to be removed, but they can be added. Fix this by
checking if the promisc_mask contains ICE_PROMISC_VLAN_RX or
ICE_PROMISC_VLAN_TX. This change was made to match what is being done
for ice_set_vsi_promisc().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently there can be a case where a DCB map is applied and there are
more interrupt vectors (vsi->num_q_vectors) than Rx queues (vsi->num_rxq)
and Tx queues (vsi->num_txq). If we try to set coalesce settings in this
case it will report a false failure. Fix this by checking if vector index
is valid with respect to the number of Tx and Rx queues configured.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It is wrong to set PF disable state flag for all VFs when freeing VF
resources - Instead, we should set VF disable state flag for each VF with
its resources being returned to the device. Right now, all VF opcodes,
mailbox communication to clear its resources as well fails - since we
already indicate that PF is in disable state, with all VFs not active. In
addition, we don't need to notify VF that PF is intending to reset it, if
it is already in disabled state.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the case of an invalid virtchannel request the driver
would return uninitialized data to the VF from the PF stack
which is a bug.  Fix by initializing the stack variable
earlier in the function before any return paths can be taken.

Fixes: 1071a835 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently when adding/deleting vlans in ice_vc_process_vlan_msg()
we are calling ice_vsi_manage_vlan_stripping() to enable/disable
when adding and deleting a VLAN respectively. This is wrong
because adding/deleting VLANs has nothing to do with configuring
VLAN stripping. VLAN stripping is configured through the
following VIRTCHNL operations:
	VIRTCHNL_OP_ENABLE_VLAN_STRIPPING
	VIRTCHNL_OP_DISABLE_VLAN_STRIPPING

Unfortunately we can't just remove this because then stripping
will never be configured on VF initialization. Fix this by
adding a new function that initializes (disables/enables) VLAN
stripping for the VF based on the device supported capabilities.
This allows us to remove the call to
ice_vsi_manage_vlan_stripping() in ice_vc_process_vlan_msg().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the host disables VLAN offloads on the VF by
not setting the VIRTCHNL_VF_OFFLOAD_VLAN capability bit
we will still honor VF VLAN configuration messages over
VIRTCHNL. These messages (i.e. enable/disable VLAN stripping
and VLAN filtering) should be blocked when the feature
is not supported. Fix that by adding a helper function to
determine if the VF is allowed to do VLAN operations based
on the host's VF configuration.

Also, mirror the VF communicated capabilities in the host's
VF configuration.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Firmware always returns 8 as the max number of supported TCs. However on
devices with more than 4 ports, the maximum number of TCs per port is
limited to 4. Check and, if necessary, correct the reporting of
capabilities for devices with more than 4 ports.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Store the number of functions the device has and use this number when
setting safe mode capabilities instead of calculating it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Co-developed-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix following sparse warnings:
drivers/net/dsa/ocelot/felix.c:351:6: warning: symbol 'felix_txtstamp' was not declared. Should it be static?
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

End.DT6 behavior makes use of seg6_lookup_nexthop() function which drops
all packets that are destined to be locally processed. However, DT* should
be able to deliver decapsulated packets that are destined to local
addresses. Function seg6_lookup_nexthop() is also used by DX6, so in order
to maintain compatibility I created another routing helper function which
is called seg6_lookup_any_nexthop(). This function is able to take into
account both packets that have to be processed locally and the ones that
are destined to be forwarded directly to another machine. Hence,
seg6_lookup_any_nexthop() is used in DT6 rather than seg6_lookup_nexthop()
to allow local delivery.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit a82055af ("netfilter: nft_payload: add VLAN offload
support"), VLAN fields in struct flow_dissector_key_vlan were unionized
with the intention of introducing another field that covered the whole TCI
header. However without a wrapping struct the subfields end up sharing the
same bits. As a result, "tc filter add ... flower vlan_id 14" specifies not
only vlan_id, but also vlan_priority.

Fix by wrapping the individual VLAN fields in a struct.

Fixes: a82055af ("netfilter: nft_payload: add VLAN offload support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-net-next-2019-11-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
The interesting new thing here is AQL, the Airtime Queue Limit
patchset from Kan Yan (Google) and Toke Høiland-Jørgensen (Redhat).
The effect is intended to eventually be similar to BQL, but byte
queue limits are not useful in wifi where the actual throughput can
vary by around 4 orders of magnitude. There are more details in the
patches themselves.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It is observed that TIPC service binding order will not be kept in the
publication event report to user if the service is subscribed after the
bindings.

For example, services are bound by application in the following order:

Server: bound port A to {18888,66,66} scope 2
Server: bound port A to {18888,33,33} scope 2

Now, if a client subscribes to the service range (e.g. {18888, 0-100}),
it will get the 'TIPC_PUBLISHED' events in that binding order only when
the subscription is started before the bindings.
Otherwise, if started after the bindings, the events will arrive in the
opposite order:

Client: received event for published {18888,33,33}
Client: received event for published {18888,66,66}

For the latter case, it is clear that the bindings have existed in the
name table already, so when reported, the events' order will follow the
order of the rbtree binding nodes (- a node with lesser 'lower'/'upper'
range value will be first).

This is correct as we provide the tracking on a specific service status
(available or not), not the relationship between multiple services.
However, some users expect to see the same order of arriving events
irrespective of when the subscription is issued. This turns out to be
easy to fix. We now add functionality to ensure that publication events
always are issued in the same temporal order as the corresponding
bindings were performed.

v2: replace the unnecessary macro - 'publication_after()' with inline
function.
v3: reuse 'time_after32()' instead of reinventing the same exact code.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When setting up a cluster with non-replicast/replicast capability
supported. This capability will be disabled for broadcast send link
in order to be backwards compatible.

However, when these non-support nodes left and be removed out the cluster.
We don't update this capability on broadcast send link. Then, some of
features that based on this capability will also disabling as unexpected.

In this commit, we make sure the broadcast send link capabilities will
be re-calculated as soon as a node removed/rejoined a cluster.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous commit added the ability to throttle stations when they queue
too much airtime in the hardware. This commit enables the functionality by
calculating the expected airtime usage of each packet that is dequeued from
the TXQs in mac80211, and accounting that as pending airtime.

The estimated airtime for each skb is stored in the tx_info, so we can
subtract the same amount from the running total when the skb is freed or
recycled. The throttling mechanism relies on this accounting to be
accurate (i.e., that we are not freeing skbs without subtracting any
airtime they were accounted for), so we put the subtraction into
ieee80211_report_used_skb(). As an optimisation, we also subtract the
airtime on regular TX completion, zeroing out the value stored in the
packet afterwards, to avoid having to do an expensive lookup of the station
from the packet data on every packet.

This patch does *not* include any mechanism to wake a throttled TXQ again,
on the assumption that this will happen anyway as a side effect of whatever
freed the skb (most commonly a TX completion).
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-5-kyan@google.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

In order for the Fq_CoDel algorithm integrated in mac80211 layer to operate
effectively to control excessive queueing latency, the CoDel algorithm
requires an accurate measure of how long packets stays in the queue, AKA
sojourn time. The sojourn time measured at the mac80211 layer doesn't
include queueing latency in the lower layer (firmware/hardware) and CoDel
expects lower layer to have a short queue. However, most 802.11ac chipsets
offload tasks such TX aggregation to firmware or hardware, thus have a deep
lower layer queue.

Without a mechanism to control the lower layer queue size, packets only
stay in mac80211 layer transiently before being sent to firmware queue.
As a result, the sojourn time measured by CoDel in the mac80211 layer is
almost always lower than the CoDel latency target, hence CoDel does little
to control the latency, even when the lower layer queue causes excessive
latency.

The Byte Queue Limits (BQL) mechanism is commonly used to address the
similar issue with wired network interface. However, this method cannot be
applied directly to the wireless network interface. "Bytes" is not a
suitable measure of queue depth in the wireless network, as the data rate
can vary dramatically from station to station in the same network, from a
few Mbps to over Gbps.

This patch implements an Airtime-based Queue Limit (AQL) to make CoDel work
effectively with wireless drivers that utilized firmware/hardware
offloading. AQL allows each txq to release just enough packets to the lower
layer to form 1-2 large aggregations to keep hardware fully utilized and
retains the rest of the frames in mac80211 layer to be controlled by the
CoDel algorithm.
Signed-off-by: Kan Yan <kyan@google.com>
[ Toke: Keep API to set pending airtime internal, fix nits in commit msg ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-4-kyan@google.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Felix recently added code to calculate airtime of packets to the mt76
driver. Import this into mac80211 so we can use it for airtime queue limit
calculations.

The airtime.c file is copied verbatim from the mt76 driver, and adjusted to
be usable in mac80211. This involves:

- Switching to mac80211 data structures.
- Adding support for 160 MHz channels and HE mode.
- Moving the symbol and duration calculations around a bit to avoid
  rounding with the higher rates and longer symbol times used for HE rates.

The per-rate TX rate calculation is also split out to its own function so
it can be used directly for the AQL calculations later.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-3-kyan@google.com
[fix HE_GROUP_IDX() to use 3 * bw, since there are 3 _gi values]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When virt_wifi interface is created, virt_wifi_newlink() is called and
it calls register_netdevice().
if register_netdevice() fails, it internally would call
->priv_destructor(), which is virt_wifi_net_device_destructor() and
it frees netdev. but virt_wifi_newlink() still use netdev.
So, use-after-free would occur in virt_wifi_newlink().

Test commands:
    ip link add dummy0 type dummy
    modprobe bonding
    ip link add bonding_masters link dummy0 type virt_wifi

Splat looks like:
[  202.220554] BUG: KASAN: use-after-free in virt_wifi_newlink+0x88b/0x9a0 [virt_wifi]
[  202.221659] Read of size 8 at addr ffff888061629cb8 by task ip/852

[  202.222896] CPU: 1 PID: 852 Comm: ip Not tainted 5.4.0-rc5 #3
[  202.223765] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  202.225073] Call Trace:
[  202.225532]  dump_stack+0x7c/0xbb
[  202.226869]  print_address_description.constprop.5+0x1be/0x360
[  202.229362]  __kasan_report+0x12a/0x16f
[  202.230714]  kasan_report+0xe/0x20
[  202.232595]  virt_wifi_newlink+0x88b/0x9a0 [virt_wifi]
[  202.233370]  __rtnl_newlink+0xb9f/0x11b0
[  202.244909]  rtnl_newlink+0x65/0x90
[ ... ]

Cc: stable@vger.kernel.org
Fixes: c7cdba31 ("mac80211-next: rtnetlink wifi simulation device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20191121122645.9355-1-ap420073@gmail.com
[trim stack dump a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Commit 7b6ddeaf ("mac80211: use QoS NDP for AP probing")
let STAs send QoS Null frames as PS triggers if the AP was
a QoS STA.  However, the mac80211 PS stack relies on an
interface flag IEEE80211_STA_NULLFUNC_ACKED for
determining trigger frame ACK, which was not being set for
acked non-QoS Null frames. The effect is an inability to
trigger hardware sleep via IEEE80211_CONF_PS since the QoS
Null frame was seemingly never acked.

This bug only applies to drivers which set both
IEEE80211_HW_REPORTS_TX_ACK_STATUS and
IEEE80211_HW_PS_NULLFUNC_STACK.

Detect the acked QoS Null frame to restore STA power save.

Fixes: 7b6ddeaf ("mac80211: use QoS NDP for AP probing")
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20191119053538.25979-4-thomas@adapt-ip.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

This is useful during testing to eg. check the currently
configured HW power save state.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20191119053538.25979-3-thomas@adapt-ip.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

In ieee80211_tx_status() we don't have an sdata struct when looking up the
destination sta. Instead, we just do a lookup by the vif addr that is the
source of the packet being completed. Factor this out into a new sta_info
getter helper, since we need to use it for accounting AQL as well.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191112130835.382062-1-toke@redhat.com
[remove internal rcu_read_lock(), document instead]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a note with a use-case for the monitor-to-dev injection
mechanism in mac80211, reported by Ben Greear.

Change-Id: I6456997ef9bc40b24ede860b6ef2fed5af49cf44
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

While using ARCH=mips CROSS_COMPILE=mips-linux-gnu- command to compile,
make C=2 drivers/net/ethernet/freescale/enetc/enetc.o

one warning can be found:
drivers/net/ethernet/freescale/enetc/enetc.c:1439:5:
warning: symbol 'enetc_setup_tc_mqprio' was not declared.
Should it be static?

This patch make symbol enetc_setup_tc_mqprio static.
Fixes: 34c6adf1 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
net: introduce and use route hint

This series leverages the listification infrastructure to avoid
unnecessary route lookup on ingress packets. In absence of custom rules,
packets with equal daddr will usually land on the same dst.

When processing packet bursts (lists) we can easily reference the previous
dst entry. When we hit the 'same destination' condition we can avoid the
route lookup, coping the already available dst.

Detailed performance numbers are available in the individual commit
messages.

v3 -> v4:
 - move helpers to their own patches (Eric D.)
 - enable hints for SUBTREE builds (David A.)
 - re-enable hints for ipv4 forward (David A.)

v2 -> v3:
 - use fib*_has_custom_rules() helpers (David A.)
 - add ip*_extract_route_hint() helper (Edward C.)
 - use prev skb as hint instead of copying data (Willem )

v1 -> v2:
 - fix build issue with !CONFIG_IP*_MULTIPLE_TABLES
 - fix potential race in ip6_list_rcv_finish()
====================
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is alike the previous change, with some additional ipv4 specific
quirk. Even when using the route hint we still have to do perform
additional per packet checks about source address validity: a new
helper is added to wrap them.

Hints are explicitly disabled if the destination is a local broadcast,
that keeps the code simple and local broadcast are a slower path anyway.

UDP flood performances vs recvmmsg() receiver:

vanilla		patched		delta
Kpps		Kpps		%
1683		1871		+11

In the worst case scenario - each packet has a different
destination address - the performance delta is within noise
range.

v3 -> v4:
 - re-enable hints for forward

v2 -> v3:
 - really fix build (sic) and hint usage check
 - use fib4_has_custom_rules() helpers (David A.)
 - add ip_extract_route_hint() helper (Edward C.)
 - use prev skb as hint instead of copying data (Willem)

v1 -> v2:
 - fix build issue with !CONFIG_IP_MULTIPLE_TABLES
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So that we can use it in the next patch.
Additionally constify the helper argument.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When doing RX batch packet processing, we currently always repeat
the route lookup for each ingress packet. When no custom rules are
in place, and there aren't routes depending on source addresses,
we know that packets with the same destination address will use
the same dst.

This change tries to avoid per packet route lookup caching
the destination address of the latest successful lookup, and
reusing it for the next packet when the above conditions are
in place. Ingress traffic for most servers should fit.

The measured performance delta under UDP flood vs a recvmmsg
receiver is as follow:

vanilla		patched		delta
Kpps		Kpps		%
1431		1674		+17

In the worst-case scenario - each packet has a different
destination address - the performance delta is within noise
range.

v3 -> v4:
 - support hints for SUBFLOW build, too (David A.)
 - several style fixes (Eric)

v2 -> v3:
 - add fib6_has_custom_rules() helpers (David A.)
 - add ip6_extract_route_hint() helper (Edward C.)
 - use hint directly in ip6_list_rcv_finish() (Willem)

v1 -> v2:
 - fix build issue with !CONFIG_IPV6_MULTIPLE_TABLES
 - fix potential race when fib6_has_custom_rules is set
   while processing a packet batch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use a per namespace counter, increment it on successful creation
of any route using the source address, decrement it on deletion
of such routes.

This allows us to check easily if the routing decision in the
current namespace depends on the packet source. Will be used
by the next patch.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It wraps the namespace field with the same name, to easily
access it regardless of build options.
Suggested-by: David Ahern <dsahern@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yangbo Lu says:

====================
Support PTP clock and hardware timestamping for DSA Felix driver

This patch-set is to support PTP clock and hardware timestamping
for DSA Felix driver. Some functions in ocelot.c/ocelot_board.c
driver were reworked/exported, so that DSA Felix driver was able
to reuse them as much as possible.

On TX path, timestamping works on packet which requires timestamp.
The injection header will be configured accordingly, and skb clone
requires timestamp will be added into a list. The TX timestamp
is final handled in threaded interrupt handler when PTP timestamp
FIFO is ready.
On RX path, timestamping is always working. The RX timestamp could
be got from extraction header.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to reuse ocelot functions as possible to enable PTP
clock and to support hardware timestamping on Felix.
On TX path, timestamping works on packet which requires timestamp.
The injection header will be configured accordingly, and skb clone
requires timestamp will be added into a list. The TX timestamp
is final handled in threaded interrupt handler when PTP timestamp
FIFO is ready.
On RX path, timestamping is always working. The RX timestamp could
be got from extraction header.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to define PTP registers for felix_vsc9959.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert to use ocelot_port_add_txtstamp_skb() for adding skbs which
require TX timestamp into list. Export it so that DSA Felix driver
could reuse it too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method getting TX timestamp by reading timestamp FIFO and
matching skbs list is common for DSA Felix driver too.
So move code out of ocelot_board.c, convert to use
ocelot_get_txtstamp() function and export it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Export ocelot_hwstamp_get/set functions so that DSA driver
is able to reuse them.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>