The process below was broken and is fixed with this patch.

//add an mirred action and give it an instance id of 1
sudo tc actions add action mirred egress mirror dev $MDEV  index 1
//create a filter which binds to mirred action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:10 action mirred index 1

Message before bug fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was broken and is fixed with this patch.

//add an ipt action and give it an instance id of 1
sudo tc actions add action ipt -j mark --set-mark 2 index 1
//create a filter which binds to ipt action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:10 action ipt index 1

Message before bug fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Late vlan action binding was broken and is fixed with this patch.

//add a vlan action to pop and give it an instance id of 1
sudo tc actions add action vlan pop index 1
//create filter which binds to vlan action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32 \
match ip dst 17.0.0.1/32 flowid 1:1 action vlan index 1

current message(before bug fix) was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If phy was suspended and is starting, current driver always enable
phy's interrupts, if phy works in polling, phy can raise unexpected
interrupt which will not be handled, the interrupt will block system
enter suspend again. So interrupts should only be re-enabled if phy
works in interrupt.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the very unlikely case __tcp_retransmit_skb() can not use the cloning
done in tcp_transmit_skb(), we need to refresh skb_mstamp before doing
the copy and transmit, otherwise TCP TS val will be an exact copy of
original transmit.

Fixes: 7faee5c0 ("tcp: remove TCP_SKB_CB(skb)->when")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Elad Kanfi says:

====================
nps_enet: Net driver bugs fix

v3:
tx_packet_sent flag is not necessary, use socket buffer pointer
instead.
Use wmb() instead of smp_wmb().

v2:
Remove code style commit for now.
Code style commit will be added after the bugs fix will be approved.

Summary:
 1. Bug description: TX done interrupts that arrives while interrupts
    are masked, during NAPI poll, will not trigger an interrupt handling.
    Since TX interrupt is of level edge we will lose the TX done interrupt.
    As a result all pending tx frames will get no service.

    Solution: Check if there is a pending tx request after unmasking the
    interrupt and if answer is yes then re-add ourselves to
    the NAPI poll list.

 2. Bug description: CPU-A before sending a frame will set a variable
    to true. CPU-B that executes the tx done interrupt service routine
    might read a non valid value of that variable.

    Solution: Use the socket buffer pointer instead of the variable,
    and add a write memory barrier at the tx sending function after
    the pointer is set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The tx interrupt is of edge type, and in case such interrupt is triggered
while it is masked it will not be handled even after tx interrupts are
re-enabled in the end of NAPI poll.
This will cause tx network to stop in the following scenario:
 * Rx is being handled, hence interrupts are masked.
 * Tx interrupt is triggered after checking if there is some tx to handle
   and before re-enabling the interrupts.
In this situation only rx transaction will release tx requests.

In order to handle the tx that was missed( if there was one ),
a NAPI reschdule was added after enabling the interrupts.
Signed-off-by: Elad Kanfi <eladkan@mellanox.com>
Acked-by: Noam Camus <noamca@mellanox.com>
Acked-by: Gilad Ben-Yossef <giladby@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Below is a description of a possible problematic
sequence. CPU-A is sending a frame and CPU-B handles
the interrupt that indicates the frame was sent. CPU-B
reads an invalid value of tx_packet_sent.

	CPU-A				CPU-B
	-----				-----
	nps_enet_send_frame
	.
	.
	tx_skb = skb
	tx_packet_sent = true
	order HW to start tx
	.
	.
	HW complete tx
			    ------> 	get tx complete interrupt
					.
					.
					if(tx_packet_sent == true)
						handle tx_skb

	end memory transaction
	(tx_packet_sent actually
	 written)

Furthermore there is a dependency between tx_skb and tx_packet_sent.
There is no assurance that tx_skb contains a valid pointer at CPU B
when it sees tx_packet_sent == true.

Solution:

Initialize tx_skb to NULL and use it to indicate that packet was sent,
in this way tx_packet_sent can be removed.
Add a write memory barrier after setting tx_skb in order to make sure
that it is valid before HW is informed and IRQ is fired.

Fixed sequence will be:

       CPU-A                           CPU-B
       -----                           -----

	tx_skb = skb
	wmb()
	.
	.
	order HW to start tx
	.
	.
	HW complete tx
			------>		get tx complete interrupt
					.
					.
					if(tx_skb != NULL)
						handle tx_skb

					tx_skb = NULL
Signed-off-by: Elad Kanfi <eladkan@mellanox.com>
Acked-by: Noam Camus <noamca@mellanox.com>
Acked-by: Gilad Ben-Yossef <giladby@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2016-05-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.6

iwlwifi

* fix P2P rates (and possibly other issues)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contain Netfilter simple fixes for your net tree,
two one-liner and one two-liner:

1) Oneliner to fix missing spinlock definition that triggers
   'BUG: spinlock bad magic on CPU#' when spinlock debugging is enabled,
   from Florian Westphal.

2) Fix missing workqueue cancelation on IDLETIMER removal,
   from Liping Zhang.

3) Fix insufficient validation of netlink of NFACCT_QUOTA in
   nfnetlink_acct, from Phil Turnbull.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Reserved fields should be set to zero to avoid exposing
bits from the kernel stack.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stack object "dte_facilities" is allocated in x25_rx_call_request(),
which is supposed to be initialized in x25_negotiate_facilities.
However, 5 fields (8 bytes in total) are not initialized. This
object is then copied to userland via copy_to_user, thus infoleak
occurs.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

When reopening the network device on ra7795/salvator-x, e.g. after a
DHCP timeout:

    IP-Config: Reopening network devices...
    genirq: Flags mismatch irq 139. 00000000 (eth0:ch24:emac) vs. 00000000 (eth0:ch24:emac)
    ravb e6800000.ethernet eth0: cannot request IRQ eth0:ch24:emac
    IP-Config: Failed to open eth0
    IP-Config: No network devices available

The "mismatch" is due to requesting an IRQ that is already in use,
while IRQF_PROBE_SHARED wasn't set.

However, the real cause is that ravb_close() doesn't release the R-Car
Gen3-specific secondary IRQ.

Add the missing free_irq() call to fix this.

Fixes: 22d4df8f ("ravb: Add support for r8a7795 SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

glibc's net/if.h contains copies of definitions from linux/if.h and these
conflict and cause build failures if both files are included by application
source code. Changes in uapi headers, which fixed header file dependencies to
include linux/if.h when it was needed, e.g. commit 1ffad83d, made the
net/if.h and linux/if.h incompatibilities visible as build failures for
userspace applications like iproute2 and xtables-addons.

This patch fixes compile errors when glibc net/if.h is included before
linux/if.h:

./linux/if.h:99:21: error: redeclaration of enumerator ‘IFF_NOARP’
./linux/if.h:98:23: error: redeclaration of enumerator ‘IFF_RUNNING’
./linux/if.h:97:26: error: redeclaration of enumerator ‘IFF_NOTRAILERS’
./linux/if.h:96:27: error: redeclaration of enumerator ‘IFF_POINTOPOINT’
./linux/if.h:95:24: error: redeclaration of enumerator ‘IFF_LOOPBACK’
./linux/if.h:94:21: error: redeclaration of enumerator ‘IFF_DEBUG’
./linux/if.h:93:25: error: redeclaration of enumerator ‘IFF_BROADCAST’
./linux/if.h:92:19: error: redeclaration of enumerator ‘IFF_UP’
./linux/if.h:252:8: error: redefinition of ‘struct ifconf’
./linux/if.h:203:8: error: redefinition of ‘struct ifreq’
./linux/if.h:169:8: error: redefinition of ‘struct ifmap’
./linux/if.h:107:23: error: redeclaration of enumerator ‘IFF_DYNAMIC’
./linux/if.h:106:25: error: redeclaration of enumerator ‘IFF_AUTOMEDIA’
./linux/if.h:105:23: error: redeclaration of enumerator ‘IFF_PORTSEL’
./linux/if.h:104:25: error: redeclaration of enumerator ‘IFF_MULTICAST’
./linux/if.h:103:21: error: redeclaration of enumerator ‘IFF_SLAVE’
./linux/if.h:102:22: error: redeclaration of enumerator ‘IFF_MASTER’
./linux/if.h:101:24: error: redeclaration of enumerator ‘IFF_ALLMULTI’
./linux/if.h:100:23: error: redeclaration of enumerator ‘IFF_PROMISC’

The cases where linux/if.h is included before net/if.h need a similar fix in
the glibc side, or the order of include files can be changed userspace
code as a workaround.

This change was tested in x86 userspace on Debian unstable with
scripts/headers_compile_test.sh:

$ make headers_install && \
  cd usr/include && ../../scripts/headers_compile_test.sh -l -k
...
cc -Wall -c -nostdinc -I /usr/lib/gcc/i586-linux-gnu/5/include -I /usr/lib/gcc/i586-linux-gnu/5/include-fixed -I . -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH/i586-linux-gnu -o /dev/null ./linux/if.h_libc_before_kernel.h
PASSED libc before kernel test: ./linux/if.h
Reported-by: Jan Engelhardt <jengelh@inai.de>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Stephen Hemminger <shemming@brocade.com>
Reported-by: Waldemar Brodkorb <mail@waldemar-brodkorb.de>
Cc: Gabriel Laskar <gabriel@lse.epita.fr>
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

   - bug in ahash SG list walking that may lead to crashes

   - resource leak in qat

   - missing RSA dependency that causes it to fail"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: rsa - select crypto mgr dependency
  crypto: hash - Fix page length clamping in hash walk
  crypto: qat - fix adf_ctl_drv.c:undefined reference to adf_init_pf_wq
  crypto: qat - fix invalid pf2vf_resp_wq logic

Pull networking fixes from David Miller:

 1) Check klogctl failure correctly, from Colin Ian King.

 2) Prevent OOM when under memory pressure in flowcache, from Steffen
    Klassert.

 3) Fix info leak in llc and rtnetlink ifmap code, from Kangjie Lu.

 4) Memory barrier and multicast handling fixes in bnxt_en, from Michael
    Chan.

 5) Endianness bug in mlx5, from Daniel Jurgens.

 6) Fix disconnect handling in VSOCK, from Ian Campbell.

 7) Fix locking of netdev list walking in get_bridge_ifindices(), from
    Nikolay Aleksandrov.

 8) Bridge multicast MLD parser can look at wrong packet offsets, fix
    from Linus Lüssing.

 9) Fix chip hang in qede driver, from Sudarsana Reddy Kalluru.

10) Fix missing setting of encapsulation before inner handling completes
    in udp_offload code, from Jarno Rajahalme.

11) Missing rollbacks during LAG join and flood configuration failures
    in mlxsw driver, from Ido Schimmel.

12) Fix error code checks in netxen driver, from Dan Carpenter.

13) Fix key size in new macsec driver, from Sabrina Dubroca.

14) Fix mlx5/VXLAN dependencies, from Arnd Bergmann.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
  net/mlx5e: make VXLAN support conditional
  Revert "net/mlx5: Kconfig: Fix MLX5_EN/VXLAN build issue"
  macsec: key identifier is 128 bits, not 64
  Documentation/networking: more accurate LCO explanation
  macvtap: segmented packet is consumed
  tools: bpf_jit_disasm: check for klogctl failure
  qede: uninitialized variable in qede_start_xmit()
  netxen: netxen_rom_fast_read() doesn't return -1
  netxen: reversed condition in netxen_nic_set_link_parameters()
  netxen: fix error handling in netxen_get_flash_block()
  mlxsw: spectrum: Add missing rollback in flood configuration
  mlxsw: spectrum: Fix rollback order in LAG join failure
  udp_offload: Set encapsulation before inner completes.
  udp_tunnel: Remove redundant udp_tunnel_gro_complete().
  qede: prevent chip hang when increasing channels
  net: ipv6: tcp reset, icmp need to consider L3 domain
  bridge: fix igmp / mld query parsing
  net: bridge: fix old ioctl unlocked net device walk
  VSOCK: do not disconnect socket when peer has shutdown SEND only
  net/mlx4_en: Fix endianness bug in IPV6 csum calculation
  ...

gcc support for __builtin_bswap16() was supposedly added for powerpc in
gcc 4.6, and was then later added for other architectures in gcc 4.8.

However, Stephen Rothwell reported that attempting to use it on powerpc
in gcc 4.6 fails with:

  lib/vsprintf.c:160:2: error: initializer element is not constant
  lib/vsprintf.c:160:2: error: (near initialization for 'decpair[0]')
  lib/vsprintf.c:160:2: error: initializer element is not constant
  lib/vsprintf.c:160:2: error: (near initialization for 'decpair[1]')
  ...

I'm not entirely sure what those errors mean, but I don't see them on
gcc 4.8.  So let's consider gcc 4.8 to be the official starting point
for __builtin_bswap16().

Arnd Bergmann adds:
 "I found the commit in gcc-4.8 that replaced the powerpc-specific
  implementation of __builtin_bswap16 with an architecture-independent
  one.  Apparently the powerpc version (gcc-4.6 and 4.7) just mapped to
  the lhbrx/sthbrx instructions, so it ended up not being a constant,
  though the intent of the patch was mainly to add support for the
  builtin to x86:

    https://gcc.gnu.org/bugzilla/show_bug.cgi?id=52624

  has the patch that went into gcc-4.8 and more information."

Fixes: 7322dd75 ("byteswap: try to avoid __builtin_constant_p gcc bug")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Saeed Mahameed says:

====================
net/mlx5e: Kconfig fixes for VxLAN

Reposting to net the build errors fixes posted by Arnd last week.

Originally Arnd posted those fixes to net-next, while the issue
is also seen in net.  For net-next a different approach is required
for fixing the issue as VXLAN and Device Drivers are no longer
dependent, but there is no harm for those fixes to get into net-next.

Optionally, once net is merged into net-next we can
Revert "net/mlx5e: make VXLAN support conditional" as the
CONFIG_MLX5_CORE_EN_VXLAN will no longer be required.

Applied on top: 28892865 ('mlxsw: spectrum: Add missing rollback in flood configuration')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

VXLAN can be disabled at compile-time or it can be a loadable
module while mlx5 is built-in, which leads to a link error:

drivers/net/built-in.o: In function `mlx5e_create_netdev':
ntb_netdev.c:(.text+0x106de4): undefined reference to `vxlan_get_rx_port'

This avoids the link error and makes the vxlan code optional,
like the other ethernet drivers do as well.

Link: https://patchwork.ozlabs.org/patch/589296/
Fixes: b3f63c3d ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 69976fb1.

We cannot select VXLAN when IPv4 support is disabled, that just gives
us additional build errors, including:

warning: (MLX5_CORE_EN) selects VXLAN which has unmet direct dependencies (NETDEVICES && NET_CORE && INET)
In file included from ../drivers/net/vxlan.c:36:0:
include/net/udp_tunnel.h: In function 'udp_tunnel_handle_offloads':
include/net/udp_tunnel.h:112:9: error: implicit declaration of function 'iptunnel_handle_offloads' [-Werror=implicit-function-declaration]
  return iptunnel_handle_offloads(skb, type);
         ^~~~~~~~~~~~~~~~~~~~~~~~

I'm sending a proper fix for the original bug in a separate patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MACsec standard mentions a key identifier for each key, but
doesn't specify anything about it, so I arbitrarily chose 64 bits.

IEEE 802.1X-2010 specifies MKA (MACsec Key Agreement), and defines the
key identifier to be 128 bits (96 bits "member identifier" + 32 bits
"key number").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In few places the term "ones-complement sum" was used but the actual
meaning is "the complement of the ones-complement sum".

Also, avoid enclosing long statements with underscore, to ease
readability.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If GSO packet is segmented and its segments are properly queued,
we call consume_skb() instead of kfree_skb() to be drop monitor
friendly.

Fixes: 3e4f8b78 ("macvtap: Perform GSO on forwarding path.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

klogctl can fail and return -ve len, so check for this and
return NULL to avoid passing a (size_t)-1 to malloc.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

"data_split" was never set to false.  It's just uninitialized.

Fixes: 2950219d ('qede: Add basic network device support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The error handling is broken here.  netxen_rom_fast_read() returns zero
on success and -EIO on error.  It never returns -1.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

My static checker complains that we are using "autoneg" without
initializing it.  The problem is the ->phy_read() condition is reversed
so we only set this on error instead of success.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

My static checker complained that "v" can be used unintialized if
netxen_rom_fast_read() returns -EIO.  That function never actually
returns -1.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull misc driver fixes from Gfreg KH:
 "Here are three small fixes for some driver problems that were
  reported.  Full details in the shortlog below.

  All of these have been in linux-next with no reported issues"

* tag 'char-misc-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  nvmem: mxs-ocotp: fix buffer overflow in read
  Drivers: hv: vmbus: Fix signaling logic in hv_need_to_signal_on_read()
  misc: mic: Fix for double fetch security bug in VOP driver

Pull IIO driver fixes from Grek KH:
 "It's really just IIO drivers here, some small fixes that resolve some
  'crash on boot' errors that have shown up in the -rc series, and other
  bugfixes that are required.

  All have been in linux-next with no reported problems"

* tag 'staging-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: imu: mpu6050: Fix name/chip_id when using ACPI
  iio: imu: mpu6050: fix possible NULL dereferences
  iio:adc:at91-sama5d2: Repair crash on module removal
  iio: ak8975: fix maybe-uninitialized warning
  iio: ak8975: Fix NULL pointer exception on early interrupt

Pull USB fixes from Greg KH:
 "Here are some last-remaining fixes for USB drivers to resolve issues
  that have shown up in testing.  And two new device ids as well.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  Revert "USB / PM: Allow USB devices to remain runtime-suspended when sleeping"
  usb: musb: jz4740: fix error check of usb_get_phy()
  Revert "usb: musb: musb_host: Enable HCD_BH flag to handle urb return in bottom half"
  usb: musb: gadget: nuke endpoint before setting its descriptor to NULL
  USB: serial: cp210x: add Straizona Focusers device ids
  USB: serial: cp210x: add ID for Link ECU

Pull ARM fixes from Russell King:
 "These are a number of updates to fix a few problems found in the ARM
  nommu code over the last couple of years, caused mostly by changes on
  the mmu side"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8573/1: domain: move {set,get}_domain under config guard
  ARM: 8572/1: nommu: change memory reserve for the vectors
  ARM: 8571/1: nommu: fix PMSAv7 setup

Pull media fixes from Mauro Carvalho Chehab:

  - deadlock fixes on driver probe at exynos4-is and s43-camif drivers

  - a build breakage if media controller is enabled and USB or PCI is
   built as module.

* tag 'media/v4.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] media-device: fix builds when USB or PCI is compiled as module
  [media] media: s3c-camif: fix deadlock on driver probe()
  [media] media: exynos4-is: fix deadlock on driver probe

Pull libata fixes from Tejun Heo:
 "An ahci driver addition and updates to ahci port enable handling for
  some platform devices"

* 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ata: add AMD Seattle platform driver
  ARM: dts: apq8064: add ahci ports-implemented mask
  ata: ahci-platform: Add ports-implemented DT bindings.
  libahci: save port map for forced port map

Pull rdma fix from Doug Ledford:
 "Fix for max sector calculation in iSER"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  IB/iser: Fix max_sectors calculation

When we fail to set the flooding configuration for the broadcast and
unregistered multicast traffic, we should revert the flooding
configuration of the unknown unicast traffic.

Fixes: 0293038e ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the leave procedure in the error path symmetric to the join
procedure and first remove the port from the collector before
potentially destroying the LAG.

Fixes: 0d65fc13 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

UDP tunnel segmentation code relies on the inner offsets being set for
an UDP tunnel GSO packet, but the inner *_complete() functions will
set the inner offsets only if 'encapsulation' is set before calling
them.  Currently, udp_gro_complete() sets 'encapsulation' only after
the inner *_complete() functions are done.  This causes the inner
offsets having invalid values after udp_gro_complete() returns, which
in turn will make it impossible to properly segment the packet in case
it needs to be forwarded, which would be visible to the user either as
invalid packets being sent or as packet loss.

This patch fixes this by setting skb's 'encapsulation' in
udp_gro_complete() before calling into the inner complete functions,
and by making each possible UDP tunnel gro_complete() callback set the
inner_mac_header to the beginning of the tunnel payload.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Reviewed-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>