- 22 Oct, 2019 24 commits
-
-
Jakub Kicinski authored
Heiner Kallweit says: ==================== The attempt to improve performance by changing the PCIe max read request size was added in the vendor driver more than 10 years back and copied to r8169 driver. In the vendor driver this has been removed long ago. Obviously it had no effect, also in my tests I didn't see any difference. Typically the max payload size is less than 512 bytes anyway, and the PCI core takes care that the maximum supported value is set. So let's remove fiddling with PCIe max read request size from r8169 too. This change allows to simplify the driver in the subsequent three patches of this series. ==================== Signed-off-by:Jakub Kicinski <jakub.kicinski@netronome.com>
-
Heiner Kallweit authored
We can remove rtl_hw_start_8168bef() and use rtl_hw_start_8168b() instead because setting register Config4 is done in rtl_jumbo_config(), being called from rtl_hw_start(). Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
We can remove rtl_hw_start_8168dp() because it's the same as rtl_hw_start_8168dp() now. Signed-off-by:
-
Heiner Kallweit authored
r8168b_0_hw_jumbo_enable() and r8168b_0_hw_jumbo_disable() both do the same and just set PCI_EXP_DEVCTL_NOSNOOP_EN. We can simplify the code by moving this setting for RTL8168B to rtl_hw_start_8168(). Signed-off-by:
-
Heiner Kallweit authored
The attempt to improve performance by changing the PCIe max read request size was added in the vendor driver more than 10 years back and copied to r8169 driver. In the vendor driver this has been removed long ago. Obviously it had no effect, also in my tests I didn't see any difference. Typically the max payload size is less than 512 bytes anyway, and the PCI core takes care that the maximum supported value is set. So let's remove fiddling with PCIe max read request size from r8169 too. Signed-off-by:
-
Jakub Kicinski authored
Karsten Graul says: ==================== More patches to address abnormal termination processing of sockets and link groups. ==================== Signed-off-by: -
Ursula Braun authored
With the introduction of the link group termination worker there is no longer a need to postpone smc_close_active_abort() to a worker. To protect socket destruction due to normal and abnormal socket closing, the socket refcount is increased. Signed-off-by:
Ursula Braun <ubraun@linux.ibm.com> Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
-
Ursula Braun authored
Use a worker for link group termination to guarantee process context. Signed-off-by:
-
Ursula Braun authored
If a link group and its connections must be terminated, * wake up socket waiters * do not enable buffer reuse A linkgroup might be terminated while normal connection closing is running. Avoid buffer reuse and its related LLC DELETE RKEY call, if linkgroup termination has started. And use the earliest indication of linkgroup termination possible, namely the removal from the linkgroup list. Signed-off-by:
-
Ursula Braun authored
There are lots of link group termination scenarios. Most of them still allow to inform the peer of the terminating sockets about aborting. This patch tries to call smc_close_abort() for terminating sockets. And the internal TCP socket is reset with tcp_abort(). Signed-off-by:
-
Ursula Braun authored
Usually link groups are freed delayed to enable quick connection creation for a follow-on SMC socket. Terminated link groups are freed faster. This patch makes sure, fast schedule of link group freeing is not rescheduled by a delayed schedule. And it makes sure link group freeing is not rescheduled, if the real freeing is already running. Signed-off-by:
-
Ursula Braun authored
Locking hierarchy requires that the link group conns_lock can be taken if the socket lock is held, but not vice versa. Nevertheless socket termination during abnormal link group termination should be protected by the socket lock. This patch reduces the time segments the link group conns_lock is held to enable usage of lock_sock in smc_lgr_terminate(). Signed-off-by:
-
Ursula Braun authored
When a link group is to be terminated, it is sufficient to hold the lgr lock when unlinking the link group from its list. Move the lock-protected link group unlinking into smc_lgr_terminate(). Signed-off-by:
-
Ursula Braun authored
The resources for a terminated socket are being cleaned up. This patch makes sure * no more data is received for an actively terminated socket * no more data is sent for an actively or passively terminated socket Signed-off-by:
-
Jakub Kicinski authored
Ido Schimmel says: ==================== Vadim says: This patch set extends the size of QSFP EEPROM for the cable types SSF-8436 and SFF-8636 from 256 bytes to 640 bytes. This allows ethtool to show correct information for these cable types (more details below). Patch #1 adds a macro that computes the EEPROM page number from the provided offset specified in the request. Patch #2 teaches the driver to access the information stored in the upper pages of the QSFP memory map. Details and examples: SFF-8436 specification defines pages 0, 1, 2 and 3. Page 0 contains lower memory page offsets (from 0x00 to 0x7f) and upper page offsets (from 0x80 to 0xfe). Upper pages 1, 2 and 3 are optional and can be empty. Page 1 is provided if upper page 0 byte 0xc3 bit 6 is set. Page 2 is provided if upper page 0 byte 0xc3 bit 7 is set. Page 3 is provided if lower page 0 byte 0x02 bit 2 is cleared. Offset 0xc3 for the upper page is provided as 0x43 = 0xc3 - 0x80. As a result of exposing 256 bytes only, ethtool shows wrong information for pages 1, 2 and 3. In the below hex dump from ethtool for a cable compliant to SFF-8636 specification, it can be seen that EEPROM of this device contains optical diagnostic page (lower page 0 byte 0x02 bit 2 is cleared), but it is not exposed, as the length defined for this type is 256 bytes. $ ethtool -m sfp42 hex on Offset Values ------ ------ 0x0000: 11 07 00 ff 00 ff 00 00 00 55 55 00 00 00 00 00 0x0010: 00 00 00 00 00 00 2a 90 00 00 82 ae 00 00 00 00 0x0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0050: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 0x0060: 00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0080: 11 8c 0c 80 00 00 00 00 00 00 00 05 ff 00 00 23 0x0090: 00 00 32 00 4d 65 6c 6c 61 6e 6f 78 20 20 20 20 0x00a0: 20 20 20 20 00 00 02 c9 4d 4d 41 31 42 30 30 2d 0x00b0: 53 53 31 20 20 20 20 20 41 32 42 68 0b b8 46 05 0x00c0: 02 07 f5 9e 4d 54 31 38 33 34 46 54 30 33 38 34 0x00d0: 36 20 20 20 31 38 30 37 30 33 00 00 0c 10 67 c2 0x00e0: 38 32 36 46 4d 41 32 32 36 49 30 31 31 35 20 20 0x00f0: 00 00 00 00 00 00 00 00 00 00 01 00 0e 00 00 00 After changing the length returned by get_module_info() callback from 256 bytes to 640 bytes, the upper pages 1, 2 and 3 are exposed by ethtool. In the below hex dump from the same cable it can be seen that the optical diagnostic page (page 3, from offset 0x0200) has non-zero data. $ ethtool -m sfp42 hex on Offset Values ------ ------ 0x0000: 11 07 00 ff 00 ff 00 00 00 55 55 00 00 00 00 00 0x0010: 00 00 00 00 00 00 27 79 00 00 82 c5 00 00 00 00 0x0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0050: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 0x0060: 00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0080: 11 8c 0c 80 00 00 00 00 00 00 00 05 ff 00 00 23 0x0090: 00 00 32 00 4d 65 6c 6c 61 6e 6f 78 20 20 20 20 0x00a0: 20 20 20 20 00 00 02 c9 4d 4d 41 31 42 30 30 2d 0x00b0: 53 53 31 20 20 20 20 20 41 32 42 68 0b b8 46 05 0x00c0: 02 07 f5 9e 4d 54 31 38 33 34 46 54 30 33 38 34 0x00d0: 36 20 20 20 31 38 30 37 30 33 00 00 0c 10 67 c2 0x00e0: 38 32 36 46 4d 41 32 32 36 49 30 31 31 35 20 20 0x00f0: 00 00 00 00 00 00 00 00 00 00 01 00 0e 00 00 00 0x0100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0110: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0120: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0130: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0140: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0150: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0160: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0170: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0190: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x01f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0200: 50 00 f6 00 46 00 00 00 00 00 00 00 00 00 00 00 0x0210: 88 b8 79 18 87 5a 7a 76 00 00 00 00 00 00 00 00 0x0220: 00 00 00 00 00 00 00 00 00 00 18 30 0e 61 60 b7 0x0230: 87 71 01 d3 43 e2 03 a5 10 9a 0a ba 0f a0 0b b8 0x0240: 87 71 02 d4 43 e2 05 a5 00 00 00 00 00 00 00 00 0x0250: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0260: a7 03 00 00 00 00 00 00 00 00 44 44 22 22 11 11 0x0270: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 And 'ethtool -m sfp42' shows the real values for the below fields, while before it exposed zeros for these fields: Laser bias current high alarm threshold : 8.500 mA Laser bias current low alarm threshold : 5.492 mA Laser bias current high warning threshold : 8.000 mA Laser bias current low warning threshold : 6.000 mA Laser output power high alarm threshold : 3.4673 mW / 5.40 dBm Laser output power low alarm threshold : 0.0724 mW / -11.40 dBm Laser output power high warning threshold : 1.7378 mW / 2.40 dBm Laser output power low warning threshold : 0.1445 mW / -8.40 dBm Module temperature high alarm threshold : 80.00 degrees C / 176.00 F Module temperature low alarm threshold : -10.00 degrees C / 14.00 F Module temperature high warning threshold : 70.00 degrees C / 158.00 F Module temperature low warning threshold : 0.00 degrees C / 32.00 F Module voltage high alarm threshold : 3.5000 V Module voltage low alarm threshold : 3.1000 V ==================== Signed-off-by: -
Vadim Pasternak authored
Extend the size of QSFP EEPROM for the cable types SSF8436 and SFF8636 from 256 to 640 bytes in order to expose all the EEPROM pages by ethtool. For SFF-8636 and SFF-8436 specifications, the driver exposes 256 bytes of data for ethtool's get_module_eeprom() callback. This is because the driver uses the below defines to specify SFF module length in ethtool's get_module_info() callback: 'ETH_MODULE_SFF_8636_LEN' and 'ETH_MODULE_SFF_8436_LEN' (both are 256). As a result of exposing 256 bytes only, ethtool shows wrong "zero" info for pages 1, 2, 3. The patch changes the length returned by callback for get_module_info() to the values from the next defines: 'ETH_MODULE_SFF_8636_MAX_LEN' and 'ETH_MODULE_SFF_8436_MAX_LEN' (both are 640) to allow exposing of upper page 1, 2 and 3. Signed-off-by:
Vadim Pasternak <vadimp@mellanox.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Vadim Pasternak authored
Provide a macro for getting QSFP module EEPROM page number from the optional upper page number row offset, specified in request. Signed-off-by:
-
Juergen Gross authored
Do some cleanup of the netback init and deinit code: - add an omnipotent queue deinit function usable from xenvif_disconnect_data() and the error path of xenvif_connect_data() - only install the irq handlers after initializing all relevant items (especially the kthreads related to the queue) - there is no need to use get_task_struct() after creating a kthread and using put_task_struct() again after having stopped it. - use kthread_run() instead of kthread_create() to spare the call of wake_up_process(). Signed-off-by:
Juergen Gross <jgross@suse.com> Reviewed-by:
Paul Durrant <pdurrant@gmail.com> Signed-off-by:
-
Jakub Kicinski authored
Hayes Wang says: ==================== Support loading the firmware of the PHY with the type of RTL_FW_PHY_NC. ==================== Signed-off-by: -
Hayes Wang authored
Support the firmware of PHY NC which is used to fix the issue found for PHY. Currently, only RTL_VER_04, RTL_VER_05, and RTL_VER_06 need it. The order of loading PHY firmware would be RTL_FW_PHY_START RTL_FW_PHY_NC RTL_FW_PHY_STOP The RTL_FW_PHY_START/RTL_FW_PHY_STOP are used to lock/unlock the PHY, and set/clear the patch key from the firmware file. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
Hayes Wang authored
Move r8153_patch_request() forward for later patch. Signed-off-by:
-
Hayes Wang authored
Make sure @fw_offset field of struct fw_mac is more than the size of struct fw_mac. Signed-off-by:
-
Hayes Wang authored
The struct fw_type_1 is used by MAC only, so rename it to a meaningful one. Besides, adjust two messages. Replace "load xxx fail" with "check xxx fail" Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueJakub Kicinski authored
Jeff Kirsher says: ==================== 1GbE Intel Wired LAN Driver Updates 2019-10-21 This series contains updates to e1000e and igc only. Sasha adds stream control transmission protocol (SCTP) CRC checksum support for igc. Also added S0ix support to the e1000e driver. Then added multicast support by adding the address list to the MTA table and providing the option for IPv6 address for igc. In addition, added receive checksum support to igc as well. Lastly, cleaned up some code that was not fully implemented yet for the VLAN filter table array. v2: Dropped patch 1 & 2 from the original series. Patch 1 is being sent to 'net' tree as a fix and patch 2 implementation needs to be re-worked. Updated the patch to add support for S0ix to fix the reverse Xmas tree issues and made the entry/exit functions void since they constantly returned success. All based on community feedback. v3: Cleaned up patch 4 of the series based on feedback from the community. Cleaned up a stray comma in a code comment and removed the 'inline' of a function that would be inlined by the compiler anyways. ==================== Signed-off-by:
-
- 21 Oct, 2019 16 commits
-
-
Davide Caratti authored
Use tcf_tm_dump(), instead of an open coded variant (no functional change in this patch). Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Heiner Kallweit says: ==================== net: phy: marvell: support downshift as PHY tunable So far downshift is implemented for one small use case only and can't be controlled from userspace. So let's implement this feature properly as a PHY tunable so that it can be controlled via ethtool. ==================== Signed-off-by: -
Heiner Kallweit authored
Instead of superseded function marvell_set_downshift() we can use new function m88e1111_set_downshift() in m88e1116r_config_init(). For this m88e1116r_config_init() has to be moved in the code. Signed-off-by:
-
Heiner Kallweit authored
So far downshift is implemented for one small use case only and can't be controlled from userspace. So let's implement this feature properly as a PHY tunable so that it can be controlled via ethtool. More Marvell PHY's may support downshift, but I restricted it for now to the ones where I have the datasheet. Signed-off-by:
-
Roman Mashak authored
Added test cases for IP header operations: - set tos/precedence - add value to tos/precedence - clear tos/precedence - invert tos/precedence Signed-off-by:
Roman Mashak <mrv@mojatatu.com> Signed-off-by:
-
David S. Miller authored
Lorenzo Bianconi says: ==================== add XDP support to mvneta driver Add XDP support to mvneta driver for devices that rely on software buffer management. Supported verdicts are: - XDP_DROP - XDP_PASS - XDP_REDIRECT - XDP_TX Moreover set ndo_xdp_xmit net_device_ops function pointer in order to support redirecting from other device (e.g. virtio-net). Convert mvneta driver to page_pool API. This series is based on previous work done by Jesper and Ilias. We will send follow-up patches to reduce DMA-sync operations. Changes since v4: - reset page_pool pointer to NULL in mvneta_rxq_drop_pkts and in mvneta_create_page_pool error path - move dma sync in mvneta_rx_refill() in patch 2/7 - verify bpf prog pointer in mvneta_xdp_setup to double-check if stop/start is really necessary - coding style fixes Changes since v3: - rename MVNETA_XDP_CONSUMED in MVNETA_XDP_DROPPED - squash patch 4/8 and patch 3/8 - fix dma sync for XDP_TX verdict - fix queue_index in xdp_rxq_info_reg - cosmetics Changes since v2: - rely on page_pool_recycle_direct instead of xdp_return_buff for XDP_DROP - define xdp buffer in mvneta_rx_swbm and avoid default initializations - use dma_sync_single_for_cpu instead of dma_sync_single_range_for_cpu - run page_pool_release_page in mvneta_swbm_add_rx_fragment even if the buffer contains just ETH_FCS Changes since v1: - sync dma buffers before refilling hw queues - fix stats accounting Changes since RFC: - implement XDP_TX - make tx pending buffer list agnostic - code refactoring - check if device is running in mvneta_xdp_setup ==================== Reviewed-by:
-
Lorenzo Bianconi authored
Implement XDP_TX verdict and ndo_xdp_xmit net_device_ops function pointer Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Lorenzo Bianconi authored
Allow tx buffer array to contain both skb and xdp buffers in order to enable xdp frame recycling adding XDP_TX verdict support Signed-off-by:
-
Lorenzo Bianconi authored
Move data buffer prefetch in mvneta_swbm_rx_frame after dma_sync_single_range_for_cpu Signed-off-by:
Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by:
Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by:
-
Lorenzo Bianconi authored
Add basic XDP support to mvneta driver for devices that rely on software buffer management. Currently supported verdicts are: - XDP_DROP - XDP_PASS - XDP_REDIRECT - XDP_ABORTED - iptables drop: $iptables -t raw -I PREROUTING -p udp --dport 9 -j DROP $nstat -n && sleep 1 && nstat IpInReceives 151169 0.0 IpExtInOctets 6953544 0.0 IpExtInNoECTPkts 151165 0.0 - XDP_DROP via xdp1 $./samples/bpf/xdp1 3 proto 0: 421419 pkt/s proto 0: 421444 pkt/s proto 0: 421393 pkt/s proto 0: 421440 pkt/s proto 0: 421184 pkt/s Tested-by:
Matteo Croce <mcroce@redhat.com> Signed-off-by:
-
Lorenzo Bianconi authored
Refactor mvneta_rx_swbm code introducing mvneta_swbm_rx_frame and mvneta_swbm_add_rx_fragment routines. Rely on build_skb in oreder to allocate skb since the previous patch introduced buffer recycling using the page_pool API. This patch fixes even an issue in the original driver where dma buffers are accessed before dma sync. mvneta driver can run on not cache coherent devices so it is necessary to sync DMA buffers before sending them to the device in order to avoid memory corruptions. Running perf analysis we can see a performance cost associated with this DMA-sync (anyway it is already there in the original driver code). In follow up patches we will add more logic to reduce DMA-sync as much as possible. Signed-off-by:
-
Lorenzo Bianconi authored
Use the page_pool api for allocations and DMA handling instead of __dev_alloc_page()/dma_map_page() and free_page()/dma_unmap_page(). Pages are unmapped using page_pool_release_page before packets go into the network stack. The page_pool API offers buffer recycling capabilities for XDP but allocates one page per packet, unless the driver splits and manages the allocated page. This is a preliminary patch to add XDP support to mvneta driver Signed-off-by:
-
Lorenzo Bianconi authored
Introduce mvneta_update_stats routine to collect {rx/tx} statistics (packets and bytes). This is a preliminary patch to add XDP support to mvneta driver Signed-off-by: -
Sasha Neftin authored
VLAN filter table array not implemented yet and shadow_vfta pointer not used. Clean up the code and remove the unused shadow_vfta pointer. Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
Extend the socket buffer field process and add Rx checksum functionality Minor: fix indentation with tab instead of spaces. Signed-off-by:
-
Sasha Neftin authored
Add multicast addresses list to the MTA table. Implement basic Rx mode support. Add option for IPv6 address settings. Signed-off-by:
-
